Hi Quentin,
On Wed, May 04, 2022 at 03:55:42PM +0200, Quentin Schulz wrote:
> From: Quentin Schulz <[email protected]>
>
> Until now, this driver only supported ACPI. This adds support for
> Device Tree too.
>
> This is heavily inspired by device tree support addition to OV8856
> driver. The differentiation between ACPI and DT mode is done through an
> is_acpi_node check.
>
> Cc: Quentin Schulz <[email protected]>
> Signed-off-by: Quentin Schulz <[email protected]>
> ---
>
> v2:
> - fixed unused-const-variable warning by removing of_match_ptr in
> of_match_table, reported by kernel test robot,
>
> drivers/media/i2c/ov5675.c | 134 +++++++++++++++++++++++++++++++++----
> 1 file changed, 121 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/media/i2c/ov5675.c b/drivers/media/i2c/ov5675.c
> index 82ba9f56baec..ccbc8dc506ff 100644
> --- a/drivers/media/i2c/ov5675.c
> +++ b/drivers/media/i2c/ov5675.c
> @@ -3,10 +3,13 @@
>
> #include <asm/unaligned.h>
> #include <linux/acpi.h>
> +#include <linux/clk.h>
> #include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> #include <linux/i2c.h>
#include <linux/mod_devicetable.h>
for struct of_device_id
> #include <linux/module.h>
> #include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> #include <media/v4l2-ctrls.h>
> #include <media/v4l2-device.h>
> #include <media/v4l2-fwnode.h>
> @@ -17,7 +20,7 @@
>
> #define OV5675_LINK_FREQ_450MHZ 450000000ULL
> #define OV5675_SCLK 90000000LL
> -#define OV5675_MCLK 19200000
> +#define OV5675_XVCLK_19_2 19200000
> #define OV5675_DATA_LANES 2
> #define OV5675_RGB_DEPTH 10
>
> @@ -76,6 +79,14 @@
>
> #define to_ov5675(_sd) container_of(_sd, struct ov5675, sd)
>
> +static const char * const ov5675_supply_names[] = {
> + "avdd", /* Analog power */
> + "dovdd", /* Digital I/O power */
> + "dvdd", /* Digital core power */
> +};
> +
> +#define OV5675_NUM_SUPPLIES ARRAY_SIZE(ov5675_supply_names)
> +
> enum {
> OV5675_LINK_FREQ_900MBPS,
> };
> @@ -484,6 +495,9 @@ struct ov5675 {
> struct v4l2_subdev sd;
> struct media_pad pad;
> struct v4l2_ctrl_handler ctrl_handler;
> + struct clk *xvclk;
> + struct gpio_desc *reset_gpio;
> + struct regulator_bulk_data supplies[OV5675_NUM_SUPPLIES];
>
> /* V4L2 Controls */
> struct v4l2_ctrl *link_freq;
> @@ -944,6 +958,52 @@ static int ov5675_set_stream(struct v4l2_subdev *sd, int enable)
> return ret;
> }
>
> +static void __ov5675_power_off(struct ov5675 *ov5675)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov5675->sd);
> +
> + if (is_acpi_node(dev_fwnode(&client->dev)))
> + return;
> +
> + gpiod_set_value_cansleep(ov5675->reset_gpio, 1);
> + usleep_range(1000, 1200);
> +
> + regulator_bulk_disable(OV5675_NUM_SUPPLIES, ov5675->supplies);
> + clk_disable_unprepare(ov5675->xvclk);
> +}
> +
> +static int __ov5675_power_on(struct ov5675 *ov5675)
> +{
> + struct i2c_client *client = v4l2_get_subdevdata(&ov5675->sd);
> + int ret;
> +
> + if (is_acpi_node(dev_fwnode(&client->dev)))
A question for Sakari here:
I have a similar series for ov5670, where I don't use is_acpi_node()
https://patchwork.linuxtv.org/project/linux-media/patch/[email protected]/
should this be done for all drivers supporting acpi && OF ?
> + return 0;
> +
> + ret = clk_prepare_enable(ov5675->xvclk);
> + if (ret < 0) {
> + dev_err(&client->dev, "failed to enable xvclk: %d\n", ret);
> + return ret;
> + }
> +
> + gpiod_set_value_cansleep(ov5675->reset_gpio, 1);
> +
> + /* Reset pulse should be at least 2ms */
> + usleep_range(2000, 2200);
> +
> + ret = regulator_bulk_enable(OV5675_NUM_SUPPLIES, ov5675->supplies);
> + if (ret) {
> + clk_disable_unprepare(ov5675->xvclk);
> + return ret;
> + }
> +
> + gpiod_set_value_cansleep(ov5675->reset_gpio, 0);
> +
> + usleep_range(1000, 1200);
> +
> + return 0;
> +}
> +
> static int __maybe_unused ov5675_suspend(struct device *dev)
> {
> struct v4l2_subdev *sd = dev_get_drvdata(dev);
> @@ -953,6 +1013,7 @@ static int __maybe_unused ov5675_suspend(struct device *dev)
> if (ov5675->streaming)
> ov5675_stop_streaming(ov5675);
>
> + __ov5675_power_off(ov5675);
So you plumb the device power/up down in the SYSTEM_SLEEP_PM_OPS() callbacks ?
My understanding is that it would be better to create RUNTIME_PM_OPS()
for this, so that the device can be runtime suspended/resumed.
Be aware my understanding of runtime_pm is limited, better check with
Sakari too (I'll ask him to have a look).
> mutex_unlock(&ov5675->mutex);
>
> return 0;
> @@ -965,6 +1026,8 @@ static int __maybe_unused ov5675_resume(struct device *dev)
> int ret;
>
> mutex_lock(&ov5675->mutex);
> +
> + __ov5675_power_on(ov5675);
> if (ov5675->streaming) {
> ret = ov5675_start_streaming(ov5675);
> if (ret) {
> @@ -1106,32 +1169,60 @@ static const struct v4l2_subdev_internal_ops ov5675_internal_ops = {
> .open = ov5675_open,
> };
>
> -static int ov5675_check_hwcfg(struct device *dev)
> +static int ov5675_get_hwcfg(struct ov5675 *ov5675, struct device *dev)
> {
> struct fwnode_handle *ep;
> struct fwnode_handle *fwnode = dev_fwnode(dev);
> struct v4l2_fwnode_endpoint bus_cfg = {
> .bus_type = V4L2_MBUS_CSI2_DPHY
> };
> - u32 mclk;
> + u32 xvclk_rate;
> int ret;
> unsigned int i, j;
>
> if (!fwnode)
> return -ENXIO;
>
> - ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk);
> + ret = fwnode_property_read_u32(fwnode, "clock-frequency", &xvclk_rate);
Isn't "clock-frequency" a leftover from ACPI ? It shouldn't be in the OF
bindings either (you have it in 1/3).
You can use the common clock framework API as you do below for OF and
parse "clock-frequency" only for ACPI, as far as I can tell.
> if (ret) {
> dev_err(dev, "can't get clock frequency");
> return ret;
> }
>
> - if (mclk != OV5675_MCLK) {
> - dev_err(dev, "external clock %d is not supported", mclk);
> + if (!is_acpi_node(fwnode)) {
> + ov5675->xvclk = devm_clk_get(dev, "xvclk");
> + if (IS_ERR(ov5675->xvclk)) {
> + ret = PTR_ERR(ov5675->xvclk);
> + dev_err(dev, "failed to get xvclk: %d\n", ret);
> + return ret;
> + }
> +
> + clk_set_rate(ov5675->xvclk, xvclk_rate);
> + xvclk_rate = clk_get_rate(ov5675->xvclk);
> + }
> +
> + if (xvclk_rate != OV5675_XVCLK_19_2) {
> + dev_err(dev, "external clock rate %u is unsupported", xvclk_rate);
> return -EINVAL;
> }
>
> + ov5675->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(ov5675->reset_gpio)) {
> + ret = PTR_ERR(ov5675->reset_gpio);
> + dev_err(dev, "failed to get reset-gpios: %d\n", ret);
> + return ret;
> + }
> +
> + for (i = 0; i < OV5675_NUM_SUPPLIES; i++)
> + ov5675->supplies[i].supply = ov5675_supply_names[i];
> +
> + ret = devm_regulator_bulk_get(dev, OV5675_NUM_SUPPLIES,
> + ov5675->supplies);
> + if (ret)
> + return ret;
> +
> ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
> if (!ep)
> return -ENXIO;
> @@ -1186,6 +1277,8 @@ static int ov5675_remove(struct i2c_client *client)
> pm_runtime_disable(&client->dev);
> mutex_destroy(&ov5675->mutex);
>
> + __ov5675_power_off(ov5675);
> +
> return 0;
> }
>
> @@ -1195,25 +1288,31 @@ static int ov5675_probe(struct i2c_client *client)
> bool full_power;
> int ret;
>
> - ret = ov5675_check_hwcfg(&client->dev);
> + ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL);
> + if (!ov5675)
> + return -ENOMEM;
> +
> + ret = ov5675_get_hwcfg(ov5675, &client->dev);
> if (ret) {
> - dev_err(&client->dev, "failed to check HW configuration: %d",
> + dev_err(&client->dev, "failed to get HW configuration: %d",
> ret);
> return ret;
> }
>
> - ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL);
> - if (!ov5675)
> - return -ENOMEM;
> -
> v4l2_i2c_subdev_init(&ov5675->sd, client, &ov5675_subdev_ops);
>
> + ret = __ov5675_power_on(ov5675);
> + if (ret) {
> + dev_err(&client->dev, "failed to power on: %d\n", ret);
> + return ret;
> + }
> +
> full_power = acpi_dev_state_d0(&client->dev);
> if (full_power) {
> ret = ov5675_identify_module(ov5675);
> if (ret) {
> dev_err(&client->dev, "failed to find sensor: %d", ret);
> - return ret;
> + goto probe_power_off;
> }
> }
Maybe you can also update the comment at the end of the probe function
to remove references to ACPI. As you wish.
/*
* Device is already turned on by i2c-core with ACPI domain PM.
* Enable runtime PM and turn off the device.
*/
Thanks
j
>
> @@ -1262,6 +1361,8 @@ static int ov5675_probe(struct i2c_client *client)
> probe_error_v4l2_ctrl_handler_free:
> v4l2_ctrl_handler_free(ov5675->sd.ctrl_handler);
> mutex_destroy(&ov5675->mutex);
> +probe_power_off:
> + __ov5675_power_off(ov5675);
>
> return ret;
> }
> @@ -1279,11 +1380,18 @@ static const struct acpi_device_id ov5675_acpi_ids[] = {
> MODULE_DEVICE_TABLE(acpi, ov5675_acpi_ids);
> #endif
>
> +static const struct of_device_id ov5675_of_match[] = {
> + { .compatible = "ovti,ov5675", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, ov5675_of_match);
> +
> static struct i2c_driver ov5675_i2c_driver = {
> .driver = {
> .name = "ov5675",
> .pm = &ov5675_pm_ops,
> .acpi_match_table = ACPI_PTR(ov5675_acpi_ids),
> + .of_match_table = ov5675_of_match,
> },
> .probe_new = ov5675_probe,
> .remove = ov5675_remove,
> --
> 2.35.1
>
Hi Jacopo, Quentin,
On Thu, May 05, 2022 at 09:47:25AM +0200, Jacopo Mondi wrote:
> Hi Quentin,
>
> On Wed, May 04, 2022 at 03:55:42PM +0200, Quentin Schulz wrote:
> > From: Quentin Schulz <[email protected]>
> >
> > Until now, this driver only supported ACPI. This adds support for
> > Device Tree too.
> >
> > This is heavily inspired by device tree support addition to OV8856
> > driver. The differentiation between ACPI and DT mode is done through an
> > is_acpi_node check.
> >
> > Cc: Quentin Schulz <[email protected]>
> > Signed-off-by: Quentin Schulz <[email protected]>
> > ---
> >
> > v2:
> > - fixed unused-const-variable warning by removing of_match_ptr in
> > of_match_table, reported by kernel test robot,
> >
> > drivers/media/i2c/ov5675.c | 134 +++++++++++++++++++++++++++++++++----
> > 1 file changed, 121 insertions(+), 13 deletions(-)
> >
> > diff --git a/drivers/media/i2c/ov5675.c b/drivers/media/i2c/ov5675.c
> > index 82ba9f56baec..ccbc8dc506ff 100644
> > --- a/drivers/media/i2c/ov5675.c
> > +++ b/drivers/media/i2c/ov5675.c
> > @@ -3,10 +3,13 @@
> >
> > #include <asm/unaligned.h>
> > #include <linux/acpi.h>
> > +#include <linux/clk.h>
> > #include <linux/delay.h>
> > +#include <linux/gpio/consumer.h>
> > #include <linux/i2c.h>
>
> #include <linux/mod_devicetable.h>
>
> for struct of_device_id
>
> > #include <linux/module.h>
> > #include <linux/pm_runtime.h>
> > +#include <linux/regulator/consumer.h>
> > #include <media/v4l2-ctrls.h>
> > #include <media/v4l2-device.h>
> > #include <media/v4l2-fwnode.h>
> > @@ -17,7 +20,7 @@
> >
> > #define OV5675_LINK_FREQ_450MHZ 450000000ULL
> > #define OV5675_SCLK 90000000LL
> > -#define OV5675_MCLK 19200000
> > +#define OV5675_XVCLK_19_2 19200000
> > #define OV5675_DATA_LANES 2
> > #define OV5675_RGB_DEPTH 10
> >
> > @@ -76,6 +79,14 @@
> >
> > #define to_ov5675(_sd) container_of(_sd, struct ov5675, sd)
> >
> > +static const char * const ov5675_supply_names[] = {
> > + "avdd", /* Analog power */
> > + "dovdd", /* Digital I/O power */
> > + "dvdd", /* Digital core power */
> > +};
> > +
> > +#define OV5675_NUM_SUPPLIES ARRAY_SIZE(ov5675_supply_names)
> > +
> > enum {
> > OV5675_LINK_FREQ_900MBPS,
> > };
> > @@ -484,6 +495,9 @@ struct ov5675 {
> > struct v4l2_subdev sd;
> > struct media_pad pad;
> > struct v4l2_ctrl_handler ctrl_handler;
> > + struct clk *xvclk;
> > + struct gpio_desc *reset_gpio;
> > + struct regulator_bulk_data supplies[OV5675_NUM_SUPPLIES];
> >
> > /* V4L2 Controls */
> > struct v4l2_ctrl *link_freq;
> > @@ -944,6 +958,52 @@ static int ov5675_set_stream(struct v4l2_subdev *sd, int enable)
> > return ret;
> > }
> >
> > +static void __ov5675_power_off(struct ov5675 *ov5675)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov5675->sd);
> > +
> > + if (is_acpi_node(dev_fwnode(&client->dev)))
> > + return;
> > +
> > + gpiod_set_value_cansleep(ov5675->reset_gpio, 1);
> > + usleep_range(1000, 1200);
> > +
> > + regulator_bulk_disable(OV5675_NUM_SUPPLIES, ov5675->supplies);
> > + clk_disable_unprepare(ov5675->xvclk);
> > +}
> > +
> > +static int __ov5675_power_on(struct ov5675 *ov5675)
> > +{
> > + struct i2c_client *client = v4l2_get_subdevdata(&ov5675->sd);
> > + int ret;
> > +
> > + if (is_acpi_node(dev_fwnode(&client->dev)))
>
> A question for Sakari here:
>
> I have a similar series for ov5670, where I don't use is_acpi_node()
> https://patchwork.linuxtv.org/project/linux-media/patch/[email protected]/
>
> should this be done for all drivers supporting acpi && OF ?
It's better if you don't.
Regulators and GPIOs can be present in ACPI systems, too, I'm not sure
about clocks (maybe not yet?). If you check for ACPI and then bail out
here, the driver may not work on some systems.
On the other hand, you might be able to skip some of these delays in some
cases if the related resource isn't there. The datasheet probably tells
more of that.
I guess the driver or the example driver name in documentation need
some revising.
>
> > + return 0;
> > +
> > + ret = clk_prepare_enable(ov5675->xvclk);
> > + if (ret < 0) {
> > + dev_err(&client->dev, "failed to enable xvclk: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + gpiod_set_value_cansleep(ov5675->reset_gpio, 1);
> > +
> > + /* Reset pulse should be at least 2ms */
> > + usleep_range(2000, 2200);
> > +
> > + ret = regulator_bulk_enable(OV5675_NUM_SUPPLIES, ov5675->supplies);
> > + if (ret) {
> > + clk_disable_unprepare(ov5675->xvclk);
> > + return ret;
> > + }
> > +
> > + gpiod_set_value_cansleep(ov5675->reset_gpio, 0);
> > +
> > + usleep_range(1000, 1200);
> > +
> > + return 0;
> > +}
> > +
> > static int __maybe_unused ov5675_suspend(struct device *dev)
> > {
> > struct v4l2_subdev *sd = dev_get_drvdata(dev);
> > @@ -953,6 +1013,7 @@ static int __maybe_unused ov5675_suspend(struct device *dev)
> > if (ov5675->streaming)
> > ov5675_stop_streaming(ov5675);
> >
> > + __ov5675_power_off(ov5675);
>
> So you plumb the device power/up down in the SYSTEM_SLEEP_PM_OPS() callbacks ?
>
> My understanding is that it would be better to create RUNTIME_PM_OPS()
> for this, so that the device can be runtime suspended/resumed.
Yes, please. The driver already uses runtime PM.
>
> Be aware my understanding of runtime_pm is limited, better check with
> Sakari too (I'll ask him to have a look).
>
> > mutex_unlock(&ov5675->mutex);
> >
> > return 0;
> > @@ -965,6 +1026,8 @@ static int __maybe_unused ov5675_resume(struct device *dev)
> > int ret;
> >
> > mutex_lock(&ov5675->mutex);
> > +
> > + __ov5675_power_on(ov5675);
> > if (ov5675->streaming) {
> > ret = ov5675_start_streaming(ov5675);
> > if (ret) {
> > @@ -1106,32 +1169,60 @@ static const struct v4l2_subdev_internal_ops ov5675_internal_ops = {
> > .open = ov5675_open,
> > };
> >
> > -static int ov5675_check_hwcfg(struct device *dev)
> > +static int ov5675_get_hwcfg(struct ov5675 *ov5675, struct device *dev)
> > {
> > struct fwnode_handle *ep;
> > struct fwnode_handle *fwnode = dev_fwnode(dev);
> > struct v4l2_fwnode_endpoint bus_cfg = {
> > .bus_type = V4L2_MBUS_CSI2_DPHY
> > };
> > - u32 mclk;
> > + u32 xvclk_rate;
> > int ret;
> > unsigned int i, j;
> >
> > if (!fwnode)
> > return -ENXIO;
> >
> > - ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk);
> > + ret = fwnode_property_read_u32(fwnode, "clock-frequency", &xvclk_rate);
>
> Isn't "clock-frequency" a leftover from ACPI ? It shouldn't be in the OF
> bindings either (you have it in 1/3).
>
> You can use the common clock framework API as you do below for OF and
> parse "clock-frequency" only for ACPI, as far as I can tell.
Older bindings had clock-frequency on DT, too, but newer ones rely on the
frequency being set using assigned-clock- stuff.
<URL:https://hverkuil.home.xs4all.nl/spec/driver-api/camera-sensor.html#handling-clocks>
But as discussed earlier, it's not possible to technically add these as
required properties albeit it's almost certainly a bug if they're not
present in dts.
See e.g.
>
> > if (ret) {
> > dev_err(dev, "can't get clock frequency");
> > return ret;
> > }
> >
> > - if (mclk != OV5675_MCLK) {
> > - dev_err(dev, "external clock %d is not supported", mclk);
> > + if (!is_acpi_node(fwnode)) {
> > + ov5675->xvclk = devm_clk_get(dev, "xvclk");
> > + if (IS_ERR(ov5675->xvclk)) {
> > + ret = PTR_ERR(ov5675->xvclk);
> > + dev_err(dev, "failed to get xvclk: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + clk_set_rate(ov5675->xvclk, xvclk_rate);
> > + xvclk_rate = clk_get_rate(ov5675->xvclk);
>
> > + }
> > +
> > + if (xvclk_rate != OV5675_XVCLK_19_2) {
> > + dev_err(dev, "external clock rate %u is unsupported", xvclk_rate);
This would be nicer wrapped.
> > return -EINVAL;
> > }
> >
> > + ov5675->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> > + GPIOD_OUT_HIGH);
> > + if (IS_ERR(ov5675->reset_gpio)) {
> > + ret = PTR_ERR(ov5675->reset_gpio);
> > + dev_err(dev, "failed to get reset-gpios: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + for (i = 0; i < OV5675_NUM_SUPPLIES; i++)
> > + ov5675->supplies[i].supply = ov5675_supply_names[i];
> > +
> > + ret = devm_regulator_bulk_get(dev, OV5675_NUM_SUPPLIES,
> > + ov5675->supplies);
> > + if (ret)
> > + return ret;
> > +
> > ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
> > if (!ep)
> > return -ENXIO;
> > @@ -1186,6 +1277,8 @@ static int ov5675_remove(struct i2c_client *client)
> > pm_runtime_disable(&client->dev);
> > mutex_destroy(&ov5675->mutex);
> >
> > + __ov5675_power_off(ov5675);
> > +
> > return 0;
> > }
> >
> > @@ -1195,25 +1288,31 @@ static int ov5675_probe(struct i2c_client *client)
> > bool full_power;
> > int ret;
> >
> > - ret = ov5675_check_hwcfg(&client->dev);
> > + ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL);
> > + if (!ov5675)
> > + return -ENOMEM;
> > +
> > + ret = ov5675_get_hwcfg(ov5675, &client->dev);
> > if (ret) {
> > - dev_err(&client->dev, "failed to check HW configuration: %d",
> > + dev_err(&client->dev, "failed to get HW configuration: %d",
> > ret);
> > return ret;
> > }
> >
> > - ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL);
> > - if (!ov5675)
> > - return -ENOMEM;
> > -
> > v4l2_i2c_subdev_init(&ov5675->sd, client, &ov5675_subdev_ops);
> >
> > + ret = __ov5675_power_on(ov5675);
> > + if (ret) {
> > + dev_err(&client->dev, "failed to power on: %d\n", ret);
> > + return ret;
> > + }
> > +
> > full_power = acpi_dev_state_d0(&client->dev);
> > if (full_power) {
> > ret = ov5675_identify_module(ov5675);
> > if (ret) {
> > dev_err(&client->dev, "failed to find sensor: %d", ret);
> > - return ret;
> > + goto probe_power_off;
> > }
> > }
>
> Maybe you can also update the comment at the end of the probe function
> to remove references to ACPI. As you wish.
>
> /*
> * Device is already turned on by i2c-core with ACPI domain PM.
> * Enable runtime PM and turn off the device.
> */
No need for such a comment --- nothing specific to this driver there.
>
> Thanks
> j
>
> >
> > @@ -1262,6 +1361,8 @@ static int ov5675_probe(struct i2c_client *client)
> > probe_error_v4l2_ctrl_handler_free:
> > v4l2_ctrl_handler_free(ov5675->sd.ctrl_handler);
> > mutex_destroy(&ov5675->mutex);
> > +probe_power_off:
> > + __ov5675_power_off(ov5675);
> >
> > return ret;
> > }
> > @@ -1279,11 +1380,18 @@ static const struct acpi_device_id ov5675_acpi_ids[] = {
> > MODULE_DEVICE_TABLE(acpi, ov5675_acpi_ids);
> > #endif
> >
> > +static const struct of_device_id ov5675_of_match[] = {
> > + { .compatible = "ovti,ov5675", },
> > + { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, ov5675_of_match);
> > +
> > static struct i2c_driver ov5675_i2c_driver = {
> > .driver = {
> > .name = "ov5675",
> > .pm = &ov5675_pm_ops,
> > .acpi_match_table = ACPI_PTR(ov5675_acpi_ids),
> > + .of_match_table = ov5675_of_match,
> > },
> > .probe_new = ov5675_probe,
> > .remove = ov5675_remove,
--
Kind regards,
Sakari Ailus