2022-05-13 18:59:37

by Neal Liu

[permalink] [raw]
Subject: [PATCH 1/3] usb: gadget: add Aspeed ast2600 udc driver

Aspeed udc is compliant with USB2.0, supports USB High Speed
and Full Speed, backward compatible with USB1.1.

Supports independent DMA channel for each generic endpoint.
Supports 32/256 stages descriptor mode for all generic endpoints.

This driver supports full functionality including single/multiple
stages descriptor mode, and exposes 1 UDC gadget driver.

Signed-off-by: Neal Liu <[email protected]>
---
MAINTAINERS | 7 +
drivers/usb/gadget/udc/Kconfig | 13 +
drivers/usb/gadget/udc/Makefile | 1 +
drivers/usb/gadget/udc/aspeed_udc.c | 1594 +++++++++++++++++++++++++++
4 files changed, 1615 insertions(+)
create mode 100644 drivers/usb/gadget/udc/aspeed_udc.c

diff --git a/MAINTAINERS b/MAINTAINERS
index e8c52d0192a6..784d8d8e7b22 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3109,6 +3109,13 @@ S: Maintained
F: Documentation/devicetree/bindings/media/aspeed-video.txt
F: drivers/media/platform/aspeed/

+ASPEED USB UDC DRIVER
+M: Neal Liu <[email protected]>
+L: [email protected] (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/usb/aspeed,udc.yaml
+F: drivers/usb/gadget/udc/aspeed_udc.c
+
ASUS NOTEBOOKS AND EEEPC ACPI/WMI EXTRAS DRIVERS
M: Corentin Chary <[email protected]>
L: [email protected]
diff --git a/drivers/usb/gadget/udc/Kconfig b/drivers/usb/gadget/udc/Kconfig
index 69394dc1cdfb..03535f33511b 100644
--- a/drivers/usb/gadget/udc/Kconfig
+++ b/drivers/usb/gadget/udc/Kconfig
@@ -463,6 +463,19 @@ config USB_TEGRA_XUDC
dynamically linked module called "tegra_xudc" and force all
gadget drivers to also be dynamically linked.

+config USB_ASPEED_UDC
+ tristate "Aspeed UDC driver support"
+ depends on ARCH_ASPEED || COMPILE_TEST
+ depends on USB_LIBCOMPOSITE
+ help
+ Enables Aspeed USB2.0 Device Controller driver for AST260x
+ family SoCs. The controller supports 1 control endpoint and
+ 4 programmable endpoints.
+
+ Say "y" to link the driver statically, or "m" to build a
+ dynamically linked module called "aspeed_udc" and force all
+ gadget drivers to also be dynamically linked.
+
source "drivers/usb/gadget/udc/aspeed-vhub/Kconfig"

#
diff --git a/drivers/usb/gadget/udc/Makefile b/drivers/usb/gadget/udc/Makefile
index a21f2224e7eb..12f9e4c9eb0c 100644
--- a/drivers/usb/gadget/udc/Makefile
+++ b/drivers/usb/gadget/udc/Makefile
@@ -40,5 +40,6 @@ obj-$(CONFIG_USB_GR_UDC) += gr_udc.o
obj-$(CONFIG_USB_GADGET_XILINX) += udc-xilinx.o
obj-$(CONFIG_USB_SNP_UDC_PLAT) += snps_udc_plat.o
obj-$(CONFIG_USB_ASPEED_VHUB) += aspeed-vhub/
+obj-$(CONFIG_USB_ASPEED_UDC) += aspeed_udc.o
obj-$(CONFIG_USB_BDC_UDC) += bdc/
obj-$(CONFIG_USB_MAX3420_UDC) += max3420_udc.o
diff --git a/drivers/usb/gadget/udc/aspeed_udc.c b/drivers/usb/gadget/udc/aspeed_udc.c
new file mode 100644
index 000000000000..f2756f099482
--- /dev/null
+++ b/drivers/usb/gadget/udc/aspeed_udc.c
@@ -0,0 +1,1594 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Aspeed Technology Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/prefetch.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/slab.h>
+
+#define AST_UDC_NUM_ENDPOINTS (1 + 4)
+#define AST_UDC_EP0_MAX_PACKET 64 /* EP0's max packet size */
+#define AST_UDC_EPn_MAX_PACKET 1024 /* Generic EPs max packet size */
+#define AST_UDC_DESCS_COUNT 256 /* Use 256 stages descriptor mode (32/256) */
+#define AST_UDC_DESC_MODE 1 /* Single/Multiple Stage(s) Descriptor Mode */
+
+#define AST_UDC_EP_DMA_SIZE (AST_UDC_EPn_MAX_PACKET + 8 * AST_UDC_DESCS_COUNT)
+
+/*****************************
+ * *
+ * UDC register definitions *
+ * *
+ *****************************/
+
+#define AST_UDC_FUNC_CTRL 0x00 /* Root Function Control & Status Register */
+#define AST_UDC_CONFIG 0x04 /* Root Configuration Setting Register */
+#define AST_UDC_IER 0x08 /* Interrupt Control Register */
+#define AST_UDC_ISR 0x0C /* Interrupt Status Register */
+#define AST_UDC_EP_ACK_IER 0x10 /* Programmable ep Pool ACK Interrupt Enable Reg */
+#define AST_UDC_EP_NAK_IER 0x14 /* Programmable ep Pool NAK Interrupt Enable Reg */
+#define AST_UDC_EP_ACK_ISR 0x18 /* Programmable ep Pool ACK Interrupt Status Reg */
+#define AST_UDC_EP_NAK_ISR 0x1C /* Programmable ep Pool NAK Interrupt Status Reg */
+#define AST_UDC_DEV_RESET 0x20 /* Device Controller Soft Reset Enable Register */
+#define AST_UDC_STS 0x24 /* USB Status Register */
+#define AST_VHUB_EP_DATA 0x28 /* Programmable ep Pool Data Toggle Value Set */
+#define AST_VHUB_ISO_TX_FAIL 0x2C /* Isochronous Transaction Fail Accumulator */
+#define AST_UDC_EP0_CTRL 0x30 /* Endpoint 0 Control/Status Register */
+#define AST_UDC_EP0_DATA_BUFF 0x34 /* Base Address of ep0 IN/OUT Data Buffer Reg */
+#define AST_UDC_SETUP0 0x80 /* Root Device Setup Data Buffer0 */
+#define AST_UDC_SETUP1 0x84 /* Root Device Setup Data Buffer1 */
+
+
+/* Main control reg */
+#define USB_PHY_CLK_EN BIT(31)
+#define USB_FIFO_DYN_PWRD_EN BIT(19)
+#define USB_EP_LONG_DESC BIT(18)
+#define USB_BIST_TEST_PASS BIT(13)
+#define USB_BIST_TURN_ON BIT(12)
+#define USB_PHY_RESET_DIS BIT(11)
+#define USB_TEST_MODE(x) ((x) << 8)
+#define USB_FORCE_TIMER_HS BIT(7)
+#define USB_FORCE_HS BIT(6)
+#define USB_REMOTE_WAKEUP_12MS BIT(5)
+#define USB_REMOTE_WAKEUP_EN BIT(4)
+#define USB_AUTO_REMOTE_WAKEUP_EN BIT(3)
+#define USB_STOP_CLK_IN_SUPEND BIT(2)
+#define USB_UPSTREAM_FS BIT(1)
+#define USB_UPSTREAM_EN BIT(0)
+
+/* Interrupt ctrl & status reg */
+#define UDC_IRQ_EP_POOL_NAK BIT(17)
+#define UDC_IRQ_EP_POOL_ACK_STALL BIT(16)
+#define UDC_IRQ_BUS_RESUME BIT(8)
+#define UDC_IRQ_BUS_SUSPEND BIT(7)
+#define UDC_IRQ_BUS_RESET BIT(6)
+#define UDC_IRQ_EP0_IN_DATA_NAK BIT(4)
+#define UDC_IRQ_EP0_IN_ACK_STALL BIT(3)
+#define UDC_IRQ_EP0_OUT_NAK BIT(2)
+#define UDC_IRQ_EP0_OUT_ACK_STALL BIT(1)
+#define UDC_IRQ_EP0_SETUP BIT(0)
+#define UDC_IRQ_ACK_ALL (0x1ff)
+
+/* EP isr reg */
+#define USB_EP3_ISR BIT(3)
+#define USB_EP2_ISR BIT(2)
+#define USB_EP1_ISR BIT(1)
+#define USB_EP0_ISR BIT(0)
+#define UDC_IRQ_EP_ACK_ALL (0xf)
+
+/*Soft reset reg */
+#define ROOT_UDC_SOFT_RESET BIT(0)
+
+/* USB status reg */
+#define UDC_STS_HIGHSPEED BIT(27)
+
+/* Programmable EP data toggle */
+#define EP_TOGGLE_SET_EPNUM(x) ((x) & 0x3)
+
+/* EP0 ctrl reg */
+#define EP0_GET_RX_LEN(x) ((x >> 16) & 0x7f)
+#define EP0_TX_LEN(x) ((x & 0x7f) << 8)
+#define EP0_RX_BUFF_RDY BIT(2)
+#define EP0_TX_BUFF_RDY BIT(1)
+#define EP0_STALL BIT(0)
+
+/*************************************
+ * *
+ * per-endpoint register definitions *
+ * *
+ *************************************/
+
+#define AST_UDC_EP_CONFIG 0x00 /* Endpoint Configuration Register */
+#define AST_UDC_EP_DMA_CTRL 0x04 /* DMA Descriptor List Control/Status Register */
+#define AST_UDC_EP_DMA_BUFF 0x08 /* DMA Descriptor/Buffer Base Address */
+#define AST_UDC_EP_DMA_STS 0x0C /* DMA Descriptor List R/W Pointer and Status */
+
+#define AST_UDC_EP_BASE 0x200
+#define AST_UDC_EP_OFFSET 0x10
+
+/* EP config reg */
+#define EP_SET_MAX_PKT(x) ((x & 0x3ff) << 16)
+#define EP_DATA_FETCH_CTRL(x) ((x & 0x3) << 14)
+#define EP_AUTO_DATA_DISABLE (0x1 << 13)
+#define EP_SET_EP_STALL (0x1 << 12)
+#define EP_SET_EP_NUM(x) ((x & 0xf) << 8)
+#define EP_SET_TYPE_MASK(x) ((x) << 5)
+#define EP_TYPE_BULK (0x1)
+#define EP_TYPE_INT (0x2)
+#define EP_TYPE_ISO (0x3)
+#define EP_DIR_OUT (0x1 << 4)
+#define EP_ALLOCATED_MASK (0x7 << 1)
+#define EP_ENABLE BIT(0)
+
+/* EP DMA ctrl reg */
+#define EP_DMA_CTRL_GET_PROC_STS(x) ((x >> 4) & 0xf)
+#define EP_DMA_CTRL_STS_RX_IDLE 0x0
+#define EP_DMA_CTRL_STS_TX_IDLE 0x8
+#define EP_DMA_CTRL_IN_LONG_MODE (0x1 << 3)
+#define EP_DMA_CTRL_RESET (0x1 << 2)
+#define EP_DMA_SINGLE_STAGE (0x1 << 1)
+#define EP_DMA_DESC_MODE (0x1 << 0)
+
+/* EP DMA status reg */
+#define EP_DMA_SET_TX_SIZE(x) ((x & 0x7ff) << 16)
+#define EP_DMA_GET_TX_SIZE(x) (((x) >> 16) & 0x7ff)
+#define EP_DMA_GET_RPTR(x) (((x) >> 8) & 0xff)
+#define EP_DMA_GET_WPTR(x) ((x) & 0xff)
+#define EP_DMA_SINGLE_KICK (1 << 0) /* WPTR = 1 for single mode */
+
+/* EP desc reg */
+#define AST_EP_DMA_DESC_INTR_ENABLE BIT(31)
+#define AST_EP_DMA_DESC_PID_DATA0 (0 << 14)
+#define AST_EP_DMA_DESC_PID_DATA2 BIT(14)
+#define AST_EP_DMA_DESC_PID_DATA1 (2 << 14)
+#define AST_EP_DMA_DESC_PID_MDATA (3 << 14)
+#define EP_DESC1_IN_LEN(x) ((x) & 0x1fff)
+#define AST_EP_DMA_DESC_MAX_LEN (7680) /* Max packet length for trasmit in 1 desc */
+
+struct ast_udc_request {
+ struct usb_request req;
+ struct list_head queue;
+ unsigned mapped:1;
+ unsigned int actual_dma_length;
+ u32 saved_dma_wptr;
+};
+
+#define to_ast_req(__req) container_of(__req, struct ast_udc_request, req)
+
+struct ast_dma_desc {
+ u32 des_0;
+ u32 des_1;
+};
+
+struct ast_udc_ep {
+ struct usb_ep ep;
+
+ /* Request queue */
+ struct list_head queue;
+
+ struct ast_udc_dev *udc;
+ void __iomem *ep_reg;
+ void *epn_buf;
+ dma_addr_t epn_buf_dma;
+ const struct usb_endpoint_descriptor *desc;
+
+ /* DMA Descriptors */
+ struct ast_dma_desc *descs;
+ dma_addr_t descs_dma;
+ u32 descs_wptr;
+ u32 chunk_max;
+
+ bool dir_in:1;
+ unsigned stopped:1;
+ bool desc_mode:1;
+};
+
+#define to_ast_ep(__ep) container_of(__ep, struct ast_udc_ep, ep)
+
+struct ast_udc_dev {
+ struct platform_device *pdev;
+ void __iomem *reg;
+ int irq;
+ spinlock_t lock;
+ struct clk *clk;
+ struct work_struct wake_work;
+
+ /* EP0 DMA buffers allocated in one chunk */
+ void *ep0_buf;
+ dma_addr_t ep0_buf_dma;
+ struct ast_udc_ep ep[AST_UDC_NUM_ENDPOINTS];
+
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *driver;
+ struct usb_ctrlrequest *creq;
+ enum usb_device_state suspended_from;
+ int desc_mode;
+
+ /* Force full speed only */
+ bool force_usb1:1;
+ unsigned is_control_tx:1;
+ bool wakeup_en:1;
+};
+
+#define to_ast_dev(__g) container_of(__g, struct ast_udc_dev, gadget)
+
+static const char * const ast_ep_name[] = {
+ "ep0", "ep1", "ep2", "ep3", "ep4"
+};
+
+#ifdef AST_UDC_DEBUG_ALL
+#define AST_UDC_DEBUG
+#define AST_SETUP_DEBUG
+#define AST_EP_DEBUG
+#define AST_ISR_DEBUG
+#endif
+
+#ifdef AST_SETUP_DEBUG
+#define SETUP_DBG(u, fmt, ...) \
+ dev_dbg(&(u)->pdev->dev, "%s() " fmt, __func__, ##__VA_ARGS__)
+#else
+#define SETUP_DBG(u, fmt, ...)
+#endif
+
+#ifdef AST_EP_DEBUG
+#define EP_DBG(e, fmt, ...) \
+ dev_dbg(&(e)->udc->pdev->dev, "%s():%s " fmt, __func__, \
+ (e)->ep.name, ##__VA_ARGS__)
+#else
+#define EP_DBG(ep, fmt, ...) ((void)(ep))
+#endif
+
+#ifdef AST_UDC_DEBUG
+#define UDC_DBG(u, fmt, ...) \
+ dev_dbg(&(u)->pdev->dev, "%s() " fmt, __func__, ##__VA_ARGS__)
+#else
+#define UDC_DBG(u, fmt, ...)
+#endif
+
+#ifdef AST_ISR_DEBUG
+#define ISR_DBG(u, fmt, ...) \
+ dev_dbg(&(u)->pdev->dev, "%s() " fmt, __func__, ##__VA_ARGS__)
+#else
+#define ISR_DBG(u, fmt, ...)
+#endif
+
+/*-------------------------------------------------------------------------*/
+#define ast_udc_read(udc, offset) \
+ readl((udc)->reg + (offset))
+#define ast_udc_write(udc, val, offset) \
+ writel((val), (udc)->reg + (offset))
+
+#define ast_ep_read(ep, reg) \
+ readl((ep)->ep_reg + (reg))
+#define ast_ep_write(ep, val, reg) \
+ writel((val), (ep)->ep_reg + (reg))
+
+/*-------------------------------------------------------------------------*/
+
+static void ast_udc_done(struct ast_udc_ep *ep, struct ast_udc_request *req,
+ int status)
+{
+ struct ast_udc_dev *udc = ep->udc;
+
+ EP_DBG(ep, "req @%p, len (%d/%d), buf:0x%x, dir:0x%x\n",
+ req, req->req.actual, req->req.length,
+ (u32)req->req.buf, ep->dir_in);
+
+ list_del(&req->queue);
+
+ if (req->req.status == -EINPROGRESS)
+ req->req.status = status;
+ else
+ status = req->req.status;
+
+ if (status && status != -ESHUTDOWN)
+ EP_DBG(ep, "done req:%p, status:%d\n", req, status);
+
+ spin_unlock(&udc->lock);
+ usb_gadget_giveback_request(&ep->ep, &req->req);
+ spin_lock(&udc->lock);
+}
+
+static void ast_udc_nuke(struct ast_udc_ep *ep, int status)
+{
+ int count = 0;
+
+ /* Sanity check */
+ if (&ep->queue == NULL)
+ return;
+
+ while (!list_empty(&ep->queue)) {
+ struct ast_udc_request *req;
+
+ req = list_entry(ep->queue.next, struct ast_udc_request,
+ queue);
+ ast_udc_done(ep, req, status);
+ count++;
+ }
+
+ if (count)
+ EP_DBG(ep, "Nuked %d request(s)\n", count);
+}
+
+/*
+ * Stop activity on all endpoints.
+ * Device controller for which EP activity is to be stopped.
+ *
+ * All the endpoints are stopped and any pending transfer requests if any on
+ * the endpoint are terminated.
+ */
+static void ast_udc_stop_activity(struct ast_udc_dev *udc)
+{
+ struct ast_udc_ep *ep;
+ int i;
+
+ for (i = 0; i < AST_UDC_NUM_ENDPOINTS; i++) {
+ ep = &udc->ep[i];
+ ep->stopped = 1;
+ ast_udc_nuke(ep, -ESHUTDOWN);
+ }
+}
+
+static int ast_udc_ep_enable(struct usb_ep *_ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ u16 maxpacket = usb_endpoint_maxp(desc);
+ struct ast_udc_ep *ep = to_ast_ep(_ep);
+ struct ast_udc_dev *udc = ep->udc;
+ u8 epnum = usb_endpoint_num(desc);
+ unsigned long flags;
+ u32 ep_conf = 0;
+ u8 dir_in;
+ u8 type;
+
+ if (!_ep || !ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT ||
+ maxpacket == 0 || maxpacket > ep->ep.maxpacket) {
+ EP_DBG(ep, "Failed, invalid EP enable param\n");
+ return -EINVAL;
+ }
+
+ if (!udc->driver) {
+ EP_DBG(ep, "bogus device state\n");
+ return -ESHUTDOWN;
+ }
+
+ EP_DBG(ep, "maxpacket:0x%x\n", maxpacket);
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ ep->desc = desc;
+ ep->stopped = 0;
+ ep->ep.maxpacket = maxpacket;
+ ep->chunk_max = AST_EP_DMA_DESC_MAX_LEN;
+
+ if (maxpacket < AST_UDC_EPn_MAX_PACKET)
+ ep_conf = EP_SET_MAX_PKT(maxpacket);
+
+ ep_conf |= EP_SET_EP_NUM(epnum);
+
+ type = usb_endpoint_type(desc);
+ dir_in = usb_endpoint_dir_in(desc);
+ ep->dir_in = dir_in;
+ if (!ep->dir_in)
+ ep_conf |= EP_DIR_OUT;
+
+ EP_DBG(ep, "type %d, dir_in %d\n", type, dir_in);
+ switch (type) {
+ case USB_ENDPOINT_XFER_ISOC:
+ ep_conf |= EP_SET_TYPE_MASK(EP_TYPE_ISO);
+ break;
+
+ case USB_ENDPOINT_XFER_BULK:
+ ep_conf |= EP_SET_TYPE_MASK(EP_TYPE_BULK);
+ break;
+
+ case USB_ENDPOINT_XFER_INT:
+ ep_conf |= EP_SET_TYPE_MASK(EP_TYPE_INT);
+ break;
+ }
+
+ ep->desc_mode = udc->desc_mode && ep->descs_dma && ep->dir_in;
+ if (ep->desc_mode) {
+ ast_ep_write(ep, EP_DMA_CTRL_RESET, AST_UDC_EP_DMA_CTRL);
+ ast_ep_write(ep, 0, AST_UDC_EP_DMA_STS);
+ ast_ep_write(ep, ep->descs_dma, AST_UDC_EP_DMA_BUFF);
+
+ /* Enable Long Descriptor Mode */
+ ast_ep_write(ep, EP_DMA_CTRL_IN_LONG_MODE | EP_DMA_DESC_MODE,
+ AST_UDC_EP_DMA_CTRL);
+
+ ep->descs_wptr = 0;
+
+ } else {
+ ast_ep_write(ep, EP_DMA_CTRL_RESET, AST_UDC_EP_DMA_CTRL);
+ ast_ep_write(ep, EP_DMA_SINGLE_STAGE, AST_UDC_EP_DMA_CTRL);
+ ast_ep_write(ep, 0, AST_UDC_EP_DMA_STS);
+ }
+
+ /* Cleanup data toggle just in case */
+ ast_udc_write(udc, EP_TOGGLE_SET_EPNUM(epnum), AST_VHUB_EP_DATA);
+
+ /* Enable EP */
+ ast_ep_write(ep, ep_conf | EP_ENABLE, AST_UDC_EP_CONFIG);
+
+ EP_DBG(ep, "ep_config: 0x%x\n", ast_ep_read(ep, AST_UDC_EP_CONFIG));
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static int ast_udc_ep_disable(struct usb_ep *_ep)
+{
+ struct ast_udc_ep *ep = to_ast_ep(_ep);
+ struct ast_udc_dev *udc = ep->udc;
+ unsigned long flags;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ ep->ep.desc = NULL;
+ ep->stopped = 1;
+
+ ast_udc_nuke(ep, -ESHUTDOWN);
+ ast_ep_write(ep, 0, AST_UDC_EP_CONFIG);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static struct usb_request *ast_udc_ep_alloc_request(struct usb_ep *_ep,
+ gfp_t gfp_flags)
+{
+ struct ast_udc_ep *ep = to_ast_ep(_ep);
+ struct ast_udc_request *req;
+
+ req = kzalloc(sizeof(struct ast_udc_request), gfp_flags);
+ if (!req) {
+ EP_DBG(ep, "request allocation failed\n");
+ return NULL;
+ }
+
+ INIT_LIST_HEAD(&req->queue);
+
+ return &req->req;
+}
+
+static void ast_udc_ep_free_request(struct usb_ep *_ep,
+ struct usb_request *_req)
+{
+ struct ast_udc_request *req = to_ast_req(_req);
+
+ kfree(req);
+}
+
+static int ast_dma_descriptor_setup(struct ast_udc_ep *ep, u32 dma_buf,
+ u16 tx_len, struct ast_udc_request *req)
+{
+ struct ast_udc_dev *udc = ep->udc;
+ struct device *dev = &udc->pdev->dev;
+ u32 offset, chunk;
+ int count, last;
+
+ if (!ep->descs) {
+ dev_warn(dev, "%s: Empty DMA descs list failure\n",
+ ep->ep.name);
+ return -EINVAL;
+ }
+
+ chunk = tx_len;
+ offset = count = last = 0;
+
+ EP_DBG(ep, "req @%p, %s:%d, %s:0x%x, %s:0x%x\n", req,
+ "wptr", ep->descs_wptr, "dma_buf", dma_buf,
+ "tx_len", tx_len);
+
+ /* Create Descriptor Lists */
+ while (chunk >= 0 && !last && count < AST_UDC_DESCS_COUNT) {
+
+ ep->descs[ep->descs_wptr].des_0 = dma_buf + offset;
+
+ if (chunk <= ep->chunk_max) {
+ ep->descs[ep->descs_wptr].des_1 = chunk;
+ last = 1;
+ } else {
+ ep->descs[ep->descs_wptr].des_1 = ep->chunk_max;
+ chunk -= ep->chunk_max;
+ }
+
+ EP_DBG(ep, "descs[%d]: 0x%x 0x%x, last:%d\n",
+ ep->descs_wptr,
+ ep->descs[ep->descs_wptr].des_0,
+ ep->descs[ep->descs_wptr].des_1,
+ last);
+
+ if (count == 0)
+ req->saved_dma_wptr = ep->descs_wptr;
+
+ ep->descs_wptr++;
+ count++;
+
+ if (ep->descs_wptr >= AST_UDC_DESCS_COUNT)
+ ep->descs_wptr = 0;
+
+ offset = ep->chunk_max * count;
+ }
+
+ return 0;
+}
+
+static void ast_udc_epn_kick(struct ast_udc_ep *ep, struct ast_udc_request *req)
+{
+ u32 tx_len;
+ u32 last;
+
+ last = req->req.length - req->req.actual;
+ tx_len = last > ep->ep.maxpacket ? ep->ep.maxpacket : last;
+
+ EP_DBG(ep, "kick req @%p, len:%d, dir:%d\n",
+ req, tx_len, ep->dir_in);
+
+ ast_ep_write(ep, req->req.dma + req->req.actual, AST_UDC_EP_DMA_BUFF);
+
+ /* Start DMA */
+ ast_ep_write(ep, EP_DMA_SET_TX_SIZE(tx_len), AST_UDC_EP_DMA_STS);
+ ast_ep_write(ep, EP_DMA_SET_TX_SIZE(tx_len) | EP_DMA_SINGLE_KICK,
+ AST_UDC_EP_DMA_STS);
+}
+
+static void ast_udc_epn_kick_desc(struct ast_udc_ep *ep,
+ struct ast_udc_request *req)
+{
+ u32 descs_max_size;
+ u32 tx_len;
+ u32 last;
+
+ descs_max_size = AST_EP_DMA_DESC_MAX_LEN * AST_UDC_DESCS_COUNT;
+
+ last = req->req.length - req->req.actual;
+ tx_len = last > descs_max_size ? descs_max_size : last;
+
+ EP_DBG(ep, "kick req @%p, %s:%d, %s:0x%x, %s:0x%x (%d/%d), %s:0x%x\n",
+ req, "tx_len", tx_len, "dir_in", ep->dir_in,
+ "dma", req->req.dma + req->req.actual,
+ req->req.actual, req->req.length,
+ "descs_max_size", descs_max_size);
+
+ if (!ast_dma_descriptor_setup(ep, req->req.dma + req->req.actual,
+ tx_len, req))
+ req->actual_dma_length += tx_len;
+
+ /* make sure CPU done everything before triggering DMA */
+ mb();
+
+ ast_ep_write(ep, ep->descs_wptr, AST_UDC_EP_DMA_STS);
+
+ EP_DBG(ep, "descs_wptr:%d, dstat:0x%x, dctrl:0x%x\n",
+ ep->descs_wptr,
+ ast_ep_read(ep, AST_UDC_EP_DMA_STS),
+ ast_ep_read(ep, AST_UDC_EP_DMA_CTRL));
+}
+
+static void ast_udc_ep0_queue(struct ast_udc_ep *ep,
+ struct ast_udc_request *req)
+{
+ struct ast_udc_dev *udc = ep->udc;
+ u32 tx_len;
+ u32 last;
+
+ last = req->req.length - req->req.actual;
+ tx_len = last > ep->ep.maxpacket ? ep->ep.maxpacket : last;
+
+ ast_udc_write(udc, req->req.dma + req->req.actual,
+ AST_UDC_EP0_DATA_BUFF);
+
+ if (ep->dir_in) {
+ /* IN requests, send data */
+ SETUP_DBG(udc, "IN: %s:0x%x, %s:0x%x, %s:%d (%d/%d), %s:%d\n",
+ "buf", (u32)req->req.buf,
+ "dma", req->req.dma + req->req.actual,
+ "tx_len", tx_len,
+ req->req.actual, req->req.length,
+ "dir_in", ep->dir_in);
+
+ req->req.actual += tx_len;
+ ast_udc_write(udc, EP0_TX_LEN(tx_len), AST_UDC_EP0_CTRL);
+ ast_udc_write(udc, EP0_TX_LEN(tx_len) | EP0_TX_BUFF_RDY,
+ AST_UDC_EP0_CTRL);
+
+ } else {
+ /* OUT requests, receive data */
+ SETUP_DBG(udc, "OUT: %s:%x, %s:%x, %s:(%d/%d), %s:%d\n",
+ "buf", (u32)req->req.buf,
+ "dma", req->req.dma + req->req.actual,
+ "len", req->req.actual, req->req.length,
+ "dir_in", ep->dir_in);
+
+ if (!req->req.length) {
+ /* 0 len request, send tx as completion */
+ ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
+ ep->dir_in = 0x80;
+ } else
+ ast_udc_write(udc, EP0_RX_BUFF_RDY, AST_UDC_EP0_CTRL);
+ }
+}
+
+static int ast_udc_ep_queue(struct usb_ep *_ep, struct usb_request *_req,
+ gfp_t gfp_flags)
+{
+ struct ast_udc_request *req = to_ast_req(_req);
+ struct ast_udc_ep *ep = to_ast_ep(_ep);
+ struct ast_udc_dev *udc = ep->udc;
+ struct device *dev = &udc->pdev->dev;
+ unsigned long flags;
+ int rc;
+
+ if (unlikely(!_req || !_req->complete || !_req->buf || !_ep)) {
+ dev_warn(dev, "Invalid EP request !\n");
+ return -EINVAL;
+ }
+
+ if (ep->stopped) {
+ dev_warn(dev, "%s is already stopped !\n", _ep->name);
+ return -ESHUTDOWN;
+ }
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ list_add_tail(&req->queue, &ep->queue);
+
+ req->req.actual = 0;
+ req->req.status = -EINPROGRESS;
+ req->actual_dma_length = 0;
+
+ rc = usb_gadget_map_request(&udc->gadget, &req->req, ep->dir_in);
+ if (rc) {
+ EP_DBG(ep, "Request mapping failure %d\n", rc);
+ dev_warn(dev, "Request mapping failure %d\n", rc);
+ return rc;
+ }
+
+ EP_DBG(ep, "enqueue req @%p\n", req);
+ EP_DBG(ep, "l=%d, dma:0x%x, zero:%d, is_in:%d\n",
+ _req->length, _req->dma, _req->zero, ep->dir_in);
+
+ /* EP0 request enqueue */
+ if (ep->ep.desc == NULL) {
+ if ((req->req.dma % 4) != 0) {
+ dev_warn(dev, "EP0 req dma alignment error\n");
+ return -ESHUTDOWN;
+ }
+
+ ast_udc_ep0_queue(ep, req);
+ goto end;
+ }
+
+ /* EPn request enqueue */
+ if (list_is_singular(&ep->queue)) {
+ if (ep->desc_mode)
+ ast_udc_epn_kick_desc(ep, req);
+ else
+ ast_udc_epn_kick(ep, req);
+ }
+
+end:
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static int ast_udc_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct ast_udc_ep *ep = to_ast_ep(_ep);
+ struct ast_udc_dev *udc = ep->udc;
+ struct ast_udc_request *req;
+ unsigned long flags;
+ int rc = 0;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ /* make sure it's actually queued on this endpoint */
+ list_for_each_entry(req, &ep->queue, queue) {
+ if (&req->req == _req) {
+ list_del_init(&req->queue);
+ ast_udc_done(ep, req, -ESHUTDOWN);
+ _req->status = -ECONNRESET;
+ break;
+ }
+ }
+
+ /* dequeue request not found */
+ if (&req->req != _req)
+ rc = -EINVAL;
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return rc;
+}
+
+static int ast_udc_ep_set_halt(struct usb_ep *_ep, int value)
+{
+ struct ast_udc_ep *ep = to_ast_ep(_ep);
+ struct ast_udc_dev *udc = ep->udc;
+ unsigned long flags;
+ int epnum;
+ u32 ctrl;
+
+ EP_DBG(ep, "val:%d\n", value);
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ epnum = usb_endpoint_num(ep->desc);
+
+ /* EP0 */
+ if (epnum == 0) {
+ ctrl = ast_udc_read(udc, AST_UDC_EP0_CTRL);
+ if (value)
+ ctrl |= EP0_STALL;
+ else
+ ctrl &= ~EP0_STALL;
+
+ ast_udc_write(udc, ctrl, AST_UDC_EP0_CTRL);
+
+ } else {
+ /* EPn */
+ ctrl = ast_udc_read(udc, AST_UDC_EP_CONFIG);
+ if (value)
+ ctrl |= EP_SET_EP_STALL;
+ else
+ ctrl &= ~EP_SET_EP_STALL;
+
+ ast_ep_write(ep, ctrl, AST_UDC_EP_CONFIG);
+
+ /* only epn is stopped and waits for clear */
+ ep->stopped = value ? 1 : 0;
+ }
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static const struct usb_ep_ops ast_udc_ep_ops = {
+ .enable = ast_udc_ep_enable,
+ .disable = ast_udc_ep_disable,
+ .alloc_request = ast_udc_ep_alloc_request,
+ .free_request = ast_udc_ep_free_request,
+ .queue = ast_udc_ep_queue,
+ .dequeue = ast_udc_ep_dequeue,
+ .set_halt = ast_udc_ep_set_halt,
+ /* there's only imprecise fifo status reporting */
+};
+
+static void ast_udc_ep0_rx(struct ast_udc_dev *udc)
+{
+ ast_udc_write(udc, udc->ep0_buf_dma, AST_UDC_EP0_DATA_BUFF);
+ ast_udc_write(udc, EP0_RX_BUFF_RDY, AST_UDC_EP0_CTRL);
+}
+
+static void ast_udc_ep0_tx(struct ast_udc_dev *udc)
+{
+ ast_udc_write(udc, udc->ep0_buf_dma, AST_UDC_EP0_DATA_BUFF);
+ ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
+}
+
+static void ast_udc_ep0_out(struct ast_udc_dev *udc)
+{
+ struct device *dev = &udc->pdev->dev;
+ struct ast_udc_ep *ep = &udc->ep[0];
+ struct ast_udc_request *req;
+ u16 rx_len;
+ u8 *buf;
+
+ if (list_empty(&ep->queue))
+ return;
+
+ req = list_entry(ep->queue.next, struct ast_udc_request, queue);
+
+ buf = req->req.buf;
+ rx_len = EP0_GET_RX_LEN(ast_udc_read(udc, AST_UDC_EP0_CTRL));
+ req->req.actual += rx_len;
+
+ SETUP_DBG(udc, "req %p (%d/%d)\n", req,
+ req->req.actual, req->req.length);
+
+ if ((rx_len < ep->ep.maxpacket) ||
+ (req->req.actual == req->req.length)) {
+ ast_udc_ep0_tx(udc);
+ if (!ep->dir_in)
+ ast_udc_done(ep, req, 0);
+
+ } else {
+ if (rx_len > req->req.length) {
+ // Issue Fix
+ dev_warn(dev, "Something wrong (%d/%d)\n",
+ req->req.actual, req->req.length);
+ ast_udc_ep0_tx(udc);
+ ast_udc_done(ep, req, 0);
+ return;
+ }
+
+ ep->dir_in = 0;
+
+ /* More works */
+ ast_udc_ep0_queue(ep, req);
+ }
+}
+
+static void ast_udc_ep0_in(struct ast_udc_dev *udc)
+{
+ struct ast_udc_ep *ep = &udc->ep[0];
+ struct ast_udc_request *req;
+
+ if (list_empty(&ep->queue)) {
+ if (udc->is_control_tx) {
+ ast_udc_ep0_rx(udc);
+ udc->is_control_tx = 0;
+ }
+
+ return;
+ }
+
+ req = list_entry(ep->queue.next, struct ast_udc_request, queue);
+
+ SETUP_DBG(udc, "req %p (%d/%d)\n", req,
+ req->req.actual, req->req.length);
+
+ if (req->req.length == req->req.actual) {
+ if (req->req.length)
+ ast_udc_ep0_rx(udc);
+
+ if (ep->dir_in)
+ ast_udc_done(ep, req, 0);
+
+ } else {
+ /* More works */
+ ast_udc_ep0_queue(ep, req);
+ }
+}
+
+static void ast_udc_epn_handle(struct ast_udc_dev *udc, u16 ep_num)
+{
+ struct ast_udc_ep *ep = &udc->ep[ep_num];
+ struct ast_udc_request *req;
+ u16 len = 0;
+
+ if (list_empty(&ep->queue))
+ return;
+
+ req = list_first_entry(&ep->queue, struct ast_udc_request, queue);
+
+ len = EP_DMA_GET_TX_SIZE(ast_ep_read(ep, AST_UDC_EP_DMA_STS));
+ req->req.actual += len;
+
+ EP_DBG(ep, "req @%p, length:(%d/%d), %s:0x%x\n", req,
+ req->req.actual, req->req.length, "len", len);
+
+ /* Done this request */
+ if (req->req.length == req->req.actual) {
+ ast_udc_done(ep, req, 0);
+ req = list_first_entry_or_null(&ep->queue,
+ struct ast_udc_request,
+ queue);
+
+ } else {
+ /* Check for short packet */
+ if (len < ep->ep.maxpacket) {
+ ast_udc_done(ep, req, 0);
+ req = list_first_entry_or_null(&ep->queue,
+ struct ast_udc_request,
+ queue);
+ }
+ }
+
+ /* More requests */
+ if (req)
+ ast_udc_epn_kick(ep, req);
+}
+
+static void ast_udc_epn_handle_desc(struct ast_udc_dev *udc, u16 ep_num)
+{
+ struct ast_udc_ep *ep = &udc->ep[ep_num];
+ struct device *dev = &udc->pdev->dev;
+ struct ast_udc_request *req;
+ u32 proc_sts, wr_ptr, rd_ptr;
+ u32 len_in_desc, ctrl;
+ u16 total_len = 0;
+ u16 len;
+ int i;
+
+ if (list_empty(&ep->queue)) {
+ dev_warn(dev, "%s reqest queue empty !\n", ep->ep.name);
+ return;
+ }
+
+ req = list_first_entry(&ep->queue, struct ast_udc_request, queue);
+
+ ctrl = ast_ep_read(ep, AST_UDC_EP_DMA_CTRL);
+ proc_sts = EP_DMA_CTRL_GET_PROC_STS(ctrl);
+
+ /* Check processing status is idle */
+ if (proc_sts != EP_DMA_CTRL_STS_RX_IDLE &&
+ proc_sts != EP_DMA_CTRL_STS_TX_IDLE) {
+ dev_warn(dev, "EP DMA CTRL: 0x%x, PS:0x%x\n",
+ ast_ep_read(ep, AST_UDC_EP_DMA_CTRL),
+ proc_sts);
+ return;
+ }
+
+ ctrl = ast_ep_read(ep, AST_UDC_EP_DMA_STS);
+ rd_ptr = EP_DMA_GET_RPTR(ctrl);
+ wr_ptr = EP_DMA_GET_WPTR(ctrl);
+
+ if (rd_ptr != wr_ptr) {
+ dev_warn(dev, "desc list is not empty ! %s:%d, %s:%d\n",
+ "rptr", rd_ptr, "wptr", wr_ptr);
+ return;
+ }
+
+ EP_DBG(ep, "rd_ptr:%d, wr_ptr:%d\n", rd_ptr, wr_ptr);
+ i = req->saved_dma_wptr;
+
+ do {
+ len_in_desc = EP_DESC1_IN_LEN(ep->descs[i].des_1);
+ EP_DBG(ep, "desc[%d] len: %d\n", i, len_in_desc);
+ total_len += len_in_desc;
+ i++;
+ if (i >= AST_UDC_DESCS_COUNT)
+ i = 0;
+
+ } while (i != wr_ptr);
+
+ req->req.actual += total_len;
+
+ EP_DBG(ep, "req @%p, length:(%d/%d), %s:0x%x\n", req,
+ req->req.actual, req->req.length, "len", total_len);
+
+ /* Done this request */
+ if (req->req.length == req->req.actual) {
+ ast_udc_done(ep, req, 0);
+ req = list_first_entry_or_null(&ep->queue,
+ struct ast_udc_request,
+ queue);
+
+ } else {
+ /* Check for short packet */
+ if (len < ep->ep.maxpacket) {
+ ast_udc_done(ep, req, 0);
+ req = list_first_entry_or_null(&ep->queue,
+ struct ast_udc_request,
+ queue);
+ }
+ }
+
+ /* More requests & dma descs not setup yet */
+ if (req && (req->actual_dma_length == req->req.actual)) {
+ EP_DBG(ep, "More requests\n");
+ ast_udc_epn_kick_desc(ep, req);
+ }
+}
+
+static void ast_udc_ep0_data_tx(struct ast_udc_dev *udc, u8 *tx_data, u32 len)
+{
+ if (len) {
+ memcpy(udc->ep0_buf, tx_data, len);
+
+ ast_udc_write(udc, udc->ep0_buf_dma, AST_UDC_EP0_DATA_BUFF);
+ ast_udc_write(udc, EP0_TX_LEN(len), AST_UDC_EP0_CTRL);
+ ast_udc_write(udc, EP0_TX_LEN(len) | EP0_TX_BUFF_RDY,
+ AST_UDC_EP0_CTRL);
+ udc->is_control_tx = 1;
+
+ } else
+ ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
+}
+
+static void ast_udc_getstatus(struct ast_udc_dev *udc)
+{
+ struct ast_udc_ep *ep;
+ u16 status = 0;
+ int epnum;
+
+ switch (udc->creq->bRequestType & USB_RECIP_MASK) {
+ case USB_RECIP_DEVICE:
+ /* Get device status */
+ status = 1 << USB_DEVICE_SELF_POWERED;
+ break;
+ case USB_RECIP_INTERFACE:
+ break;
+ case USB_RECIP_ENDPOINT:
+ epnum = udc->creq->wIndex & USB_ENDPOINT_NUMBER_MASK;
+ status = udc->ep[epnum].stopped;
+ break;
+ default:
+ goto stall;
+ }
+
+ ep = &udc->ep[epnum];
+ EP_DBG(ep, "status: 0x%x\n", status);
+ ast_udc_ep0_data_tx(udc, (u8 *)&status, sizeof(status));
+
+ return;
+
+stall:
+ EP_DBG(ep, "Can't respond request\n");
+ ast_udc_write(udc, ast_udc_read(udc, AST_UDC_EP0_CTRL) | EP0_STALL,
+ AST_UDC_EP0_CTRL);
+}
+
+static void ast_udc_ep0_handle_setup(struct ast_udc_dev *udc)
+{
+ struct ast_udc_ep *ep = &udc->ep[0];
+ struct ast_udc_request *req;
+ struct usb_ctrlrequest crq;
+ int req_num = 0;
+ u16 ep_num = 0;
+ int rc;
+
+ memcpy_fromio(&crq, udc->creq, sizeof(crq));
+
+ SETUP_DBG(udc, "SETEUP packet: %02x/%02x/%04x/%04x/%04x\n",
+ crq.bRequestType, crq.bRequest, le16_to_cpu(crq.wValue),
+ le16_to_cpu(crq.wIndex), le16_to_cpu(crq.wLength));
+
+ /*
+ * Cleanup ep0 request(s) in queue because
+ * there is a new control setup comes.
+ */
+ list_for_each_entry(req, &udc->ep[0].queue, queue) {
+ req_num++;
+ EP_DBG(ep, "there is req %p in ep0 queue !\n", req);
+ }
+
+ if (req_num)
+ ast_udc_nuke(&udc->ep[0], -ETIMEDOUT);
+
+ udc->ep[0].dir_in = crq.bRequestType & USB_DIR_IN;
+
+ if ((crq.bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) {
+ switch (crq.bRequest) {
+ case USB_REQ_SET_ADDRESS:
+ if (ast_udc_read(udc, AST_UDC_STS) & UDC_STS_HIGHSPEED)
+ udc->gadget.speed = USB_SPEED_HIGH;
+ else
+ udc->gadget.speed = USB_SPEED_FULL;
+
+ SETUP_DBG(udc, "set addr: 0x%x\n", crq.wValue);
+ ast_udc_write(udc, crq.wValue, AST_UDC_CONFIG);
+ goto req_complete;
+
+ case USB_REQ_CLEAR_FEATURE:
+ ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
+ SETUP_DBG(udc, "ep%d: CLEAR FEATURE\n", ep_num);
+ goto req_driver;
+
+ case USB_REQ_SET_FEATURE:
+ ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
+ SETUP_DBG(udc, "ep%d: SET FEATURE\n", ep_num);
+ goto req_driver;
+
+ case USB_REQ_GET_STATUS:
+ ast_udc_getstatus(udc);
+ return;
+
+ default:
+ goto req_driver;
+ }
+
+ }
+
+req_driver:
+ if (udc->driver) {
+ SETUP_DBG(udc, "Forwarding %s to gadget...\n",
+ udc->gadget.name);
+
+ spin_unlock(&udc->lock);
+ rc = udc->driver->setup(&udc->gadget, &crq);
+ spin_lock(&udc->lock);
+
+ } else
+ SETUP_DBG(udc, "No gadget for request !\n");
+
+ if (rc >= 0)
+ return;
+
+ /* Stall if gadget failed */
+ SETUP_DBG(udc, "Stalling, rc:0x%x\n", rc);
+ ast_udc_write(udc, ast_udc_read(udc, AST_UDC_EP0_CTRL) | EP0_STALL,
+ AST_UDC_EP0_CTRL);
+ return;
+
+req_complete:
+ SETUP_DBG(udc, "ep%d: Sending IN status without data\n", ep_num);
+ ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
+}
+
+static irqreturn_t ast_udc_isr(int irq, void *data)
+{
+ struct ast_udc_dev *udc = (struct ast_udc_dev *)data;
+ struct ast_udc_ep *ep;
+ u32 isr, ep_isr;
+ int i;
+
+ spin_lock(&udc->lock);
+
+ isr = ast_udc_read(udc, AST_UDC_ISR);
+ if (!isr)
+ goto done;
+
+ /* Ack interrupts */
+ ast_udc_write(udc, isr, AST_UDC_ISR);
+
+ if (isr & UDC_IRQ_BUS_RESET) {
+ ISR_DBG(udc, "UDC_IRQ_BUS_RESET\n");
+ udc->gadget.speed = USB_SPEED_UNKNOWN;
+
+ ep = &udc->ep[1];
+ EP_DBG(ep, "dctrl:0x%x\n",
+ ast_ep_read(ep, AST_UDC_EP_DMA_CTRL));
+
+ if (udc->driver && udc->driver->reset) {
+ spin_unlock(&udc->lock);
+ udc->driver->reset(&udc->gadget);
+ spin_lock(&udc->lock);
+ }
+ }
+
+ if (isr & UDC_IRQ_BUS_SUSPEND) {
+ ISR_DBG(udc, "UDC_IRQ_BUS_SUSPEND\n");
+ udc->suspended_from = udc->gadget.state;
+ usb_gadget_set_state(&udc->gadget, USB_STATE_SUSPENDED);
+
+ if (udc->driver && udc->driver->suspend) {
+ spin_unlock(&udc->lock);
+ udc->driver->suspend(&udc->gadget);
+ spin_lock(&udc->lock);
+ }
+ }
+
+ if (isr & UDC_IRQ_BUS_RESUME) {
+ ISR_DBG(udc, "UDC_IRQ_BUS_RESUME\n");
+ usb_gadget_set_state(&udc->gadget, udc->suspended_from);
+
+ if (udc->driver && udc->driver->resume) {
+ spin_unlock(&udc->lock);
+ udc->driver->resume(&udc->gadget);
+ spin_lock(&udc->lock);
+ }
+ }
+
+ if (isr & UDC_IRQ_EP0_IN_ACK_STALL) {
+ ISR_DBG(udc, "UDC_IRQ_EP0_IN_ACK_STALL\n");
+ ast_udc_ep0_in(udc);
+ }
+
+ if (isr & UDC_IRQ_EP0_OUT_ACK_STALL) {
+ ISR_DBG(udc, "UDC_IRQ_EP0_OUT_ACK_STALL\n");
+ ast_udc_ep0_out(udc);
+ }
+
+ if (isr & UDC_IRQ_EP0_SETUP) {
+ ISR_DBG(udc, "UDC_IRQ_EP0_SETUP\n");
+ ast_udc_ep0_handle_setup(udc);
+ }
+
+ if (isr & UDC_IRQ_EP_POOL_ACK_STALL) {
+ ISR_DBG(udc, "UDC_IRQ_EP_POOL_ACK_STALL\n");
+ ep_isr = ast_udc_read(udc, AST_UDC_EP_ACK_ISR);
+
+ /* Ack EP interrupts */
+ ast_udc_write(udc, ep_isr, AST_UDC_EP_ACK_ISR);
+
+ /* Handle each EP */
+ for (i = 0; i < AST_UDC_NUM_ENDPOINTS - 1; i++) {
+ if (ep_isr & (0x1 << i)) {
+ ep = &udc->ep[i + 1];
+ if (ep->desc_mode)
+ ast_udc_epn_handle_desc(udc, i + 1);
+ else
+ ast_udc_epn_handle(udc, i + 1);
+ }
+ }
+ }
+
+done:
+ spin_unlock(&udc->lock);
+ return IRQ_HANDLED;
+}
+
+static int ast_udc_gadget_getframe(struct usb_gadget *gadget)
+{
+ struct ast_udc_dev *udc = to_ast_dev(gadget);
+
+ return (ast_udc_read(udc, AST_UDC_STS) >> 16) & 0x7ff;
+}
+
+static void ast_udc_wake_work(struct work_struct *work)
+{
+ struct ast_udc_dev *udc = container_of(work, struct ast_udc_dev,
+ wake_work);
+ unsigned long flags;
+ u32 ctrl;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ UDC_DBG(udc, "Wakeup Host !\n");
+ ctrl = ast_udc_read(udc, AST_UDC_FUNC_CTRL);
+ ast_udc_write(udc, ctrl | USB_REMOTE_WAKEUP_EN, AST_UDC_FUNC_CTRL);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+}
+
+static void ast_udc_wakeup_all(struct ast_udc_dev *udc)
+{
+ /*
+ * A device is trying to wake the world, because this
+ * can recurse into the device, we break the call chain
+ * using a work queue
+ */
+ schedule_work(&udc->wake_work);
+}
+
+static int ast_udc_wakeup(struct usb_gadget *gadget)
+{
+ struct ast_udc_dev *udc = to_ast_dev(gadget);
+ unsigned long flags;
+ int rc = 0;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ if (!udc->wakeup_en) {
+ UDC_DBG(udc, "Remote Wakeup is disabled\n");
+ rc = -EINVAL;
+ goto err;
+ }
+
+ UDC_DBG(udc, "Device initiated wakeup\n");
+ ast_udc_wakeup_all(udc);
+
+err:
+ spin_unlock_irqrestore(&udc->lock, flags);
+ return rc;
+}
+
+/*
+ * Activate/Deactivate link with host
+ */
+static int ast_udc_pullup(struct usb_gadget *gadget, int is_on)
+{
+ struct ast_udc_dev *udc = to_ast_dev(gadget);
+ unsigned long flags;
+ u32 ctrl;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ UDC_DBG(udc, "is_on: %d\n", is_on);
+ if (is_on)
+ ctrl = ast_udc_read(udc, AST_UDC_FUNC_CTRL) | USB_UPSTREAM_EN;
+ else
+ ctrl = ast_udc_read(udc, AST_UDC_FUNC_CTRL) & ~USB_UPSTREAM_EN;
+
+ ast_udc_write(udc, ctrl, AST_UDC_FUNC_CTRL);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static int ast_udc_start(struct usb_gadget *gadget,
+ struct usb_gadget_driver *driver)
+{
+ struct ast_udc_dev *udc = to_ast_dev(gadget);
+ struct ast_udc_ep *ep;
+ unsigned long flags;
+ int i;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ UDC_DBG(udc, "\n");
+ udc->driver = driver;
+ udc->gadget.dev.of_node = udc->pdev->dev.of_node;
+
+ for (i = 0; i < AST_UDC_NUM_ENDPOINTS; i++) {
+ ep = &udc->ep[i];
+ ep->stopped = 0;
+ }
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static int ast_udc_stop(struct usb_gadget *gadget)
+{
+ struct ast_udc_dev *udc = to_ast_dev(gadget);
+ unsigned long flags;
+ u32 ctrl;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ UDC_DBG(udc, "\n");
+ ctrl = ast_udc_read(udc, AST_UDC_FUNC_CTRL) & ~USB_UPSTREAM_EN;
+ ast_udc_write(udc, ctrl, AST_UDC_FUNC_CTRL);
+
+ udc->gadget.speed = USB_SPEED_UNKNOWN;
+ udc->driver = NULL;
+
+ ast_udc_stop_activity(udc);
+ usb_gadget_set_state(&udc->gadget, USB_STATE_NOTATTACHED);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ return 0;
+}
+
+static const struct usb_gadget_ops ast_udc_ops = {
+ .get_frame = ast_udc_gadget_getframe,
+ .wakeup = ast_udc_wakeup,
+ .pullup = ast_udc_pullup,
+ .udc_start = ast_udc_start,
+ .udc_stop = ast_udc_stop,
+};
+
+/*
+ * Support 1 Control Endpoint.
+ * Support multiple programmable endpoints that can be configured to
+ * Bulk IN/OUT, Interrupt IN/OUT, and Isochronous IN/OUT type endpoint.
+ */
+static void ast_udc_init_ep(struct ast_udc_dev *udc)
+{
+ struct ast_udc_ep *ep;
+ int i;
+
+ for (i = 0; i < AST_UDC_NUM_ENDPOINTS; i++) {
+ ep = &udc->ep[i];
+ ep->ep.name = ast_ep_name[i];
+ if (i == 0) {
+ ep->ep.caps.type_control = true;
+ } else {
+ ep->ep.caps.type_iso = true;
+ ep->ep.caps.type_bulk = true;
+ ep->ep.caps.type_int = true;
+ }
+ ep->ep.caps.dir_in = true;
+ ep->ep.caps.dir_out = true;
+
+ ep->ep.ops = &ast_udc_ep_ops;
+ ep->udc = udc;
+
+ INIT_LIST_HEAD(&ep->queue);
+
+ if (i == 0) {
+ usb_ep_set_maxpacket_limit(&ep->ep,
+ AST_UDC_EP0_MAX_PACKET);
+ continue;
+ }
+
+ ep->ep_reg = udc->reg + AST_UDC_EP_BASE +
+ (AST_UDC_EP_OFFSET * (i - 1));
+
+ ep->epn_buf = udc->ep0_buf + (i * AST_UDC_EP_DMA_SIZE);
+ ep->epn_buf_dma = udc->ep0_buf_dma + (i * AST_UDC_EP_DMA_SIZE);
+ usb_ep_set_maxpacket_limit(&ep->ep, AST_UDC_EPn_MAX_PACKET);
+
+ ep->descs = ep->epn_buf + AST_UDC_EPn_MAX_PACKET;
+ ep->descs_dma = ep->epn_buf_dma + AST_UDC_EPn_MAX_PACKET;
+ ep->descs_wptr = 0;
+
+ list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
+ }
+}
+
+static void ast_udc_init_dev(struct ast_udc_dev *udc)
+{
+ INIT_WORK(&udc->wake_work, ast_udc_wake_work);
+}
+
+static void ast_udc_init_hw(struct ast_udc_dev *udc)
+{
+ u32 ctrl;
+
+ /* Enable PHY */
+ ctrl = USB_PHY_CLK_EN | USB_PHY_RESET_DIS;
+ ast_udc_write(udc, ctrl, AST_UDC_FUNC_CTRL);
+
+ udelay(1);
+ ast_udc_write(udc, 0, AST_UDC_DEV_RESET);
+
+ /* Set descriptor ring size */
+ if (AST_UDC_DESCS_COUNT == 256) {
+ ctrl |= USB_EP_LONG_DESC;
+ ast_udc_write(udc, ctrl, AST_UDC_FUNC_CTRL);
+ }
+
+ /* Mask & ack all interrupts before installing the handler */
+ ast_udc_write(udc, 0, AST_UDC_IER);
+ ast_udc_write(udc, UDC_IRQ_ACK_ALL, AST_UDC_ISR);
+
+ /* Enable some interrupts */
+ ctrl = UDC_IRQ_EP_POOL_ACK_STALL | UDC_IRQ_BUS_RESUME |
+ UDC_IRQ_BUS_SUSPEND | UDC_IRQ_BUS_RESET |
+ UDC_IRQ_EP0_IN_ACK_STALL | UDC_IRQ_EP0_OUT_ACK_STALL |
+ UDC_IRQ_EP0_SETUP;
+ ast_udc_write(udc, ctrl, AST_UDC_IER);
+
+ /* Cleanup and enable ep ACK interrupts */
+ ast_udc_write(udc, UDC_IRQ_EP_ACK_ALL, AST_UDC_EP_ACK_IER);
+ ast_udc_write(udc, UDC_IRQ_EP_ACK_ALL, AST_UDC_EP_ACK_ISR);
+
+ ast_udc_write(udc, 0, AST_UDC_EP0_CTRL);
+}
+
+static int ast_udc_remove(struct platform_device *pdev)
+{
+ struct ast_udc_dev *udc = platform_get_drvdata(pdev);
+ unsigned long flags;
+ u32 ctrl;
+
+ usb_del_gadget_udc(&udc->gadget);
+ if (udc->driver)
+ return -EBUSY;
+
+ spin_lock_irqsave(&udc->lock, flags);
+
+ /* Disable upstream port connection */
+ ctrl = ast_udc_read(udc, AST_UDC_FUNC_CTRL) & ~USB_UPSTREAM_EN;
+ ast_udc_write(udc, ctrl, AST_UDC_FUNC_CTRL);
+
+ clk_disable_unprepare(udc->clk);
+
+ spin_unlock_irqrestore(&udc->lock, flags);
+
+ if (udc->ep0_buf)
+ dma_free_coherent(&pdev->dev,
+ AST_UDC_EP_DMA_SIZE * AST_UDC_NUM_ENDPOINTS,
+ udc->ep0_buf,
+ udc->ep0_buf_dma);
+
+ udc->ep0_buf = NULL;
+
+ return 0;
+}
+
+static int ast_udc_probe(struct platform_device *pdev)
+{
+ enum usb_device_speed max_speed;
+ struct device *dev = &pdev->dev;
+ struct ast_udc_dev *udc;
+ struct resource *res;
+ int rc;
+
+ udc = devm_kzalloc(&pdev->dev, sizeof(struct ast_udc_dev), GFP_KERNEL);
+ if (!udc)
+ return -ENOMEM;
+
+ udc->gadget.dev.parent = dev;
+ udc->pdev = pdev;
+ spin_lock_init(&udc->lock);
+
+ udc->gadget.ops = &ast_udc_ops;
+ udc->gadget.ep0 = &udc->ep[0].ep;
+ udc->gadget.name = "aspeed-udc";
+ udc->gadget.dev.init_name = "gadget";
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ udc->reg = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(udc->reg)) {
+ dev_err(&pdev->dev, "Failed to map resources\n");
+ return PTR_ERR(udc->reg);
+ }
+
+ platform_set_drvdata(pdev, udc);
+
+ udc->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(udc->clk)) {
+ rc = PTR_ERR(udc->clk);
+ goto err;
+ }
+ rc = clk_prepare_enable(udc->clk);
+ if (rc) {
+ dev_err(&pdev->dev, "Failed to enable clock (0x%x)\n", rc);
+ goto err;
+ }
+
+ /* Check if we need to limit the HW to USB1 */
+ max_speed = usb_get_maximum_speed(&pdev->dev);
+ if (max_speed != USB_SPEED_UNKNOWN && max_speed < USB_SPEED_HIGH)
+ udc->force_usb1 = true;
+
+ /*
+ * Allocate DMA buffers for all EPs in one chunk
+ */
+ udc->ep0_buf = dma_alloc_coherent(&pdev->dev,
+ AST_UDC_EP_DMA_SIZE *
+ AST_UDC_NUM_ENDPOINTS,
+ &udc->ep0_buf_dma, GFP_KERNEL);
+
+ udc->gadget.speed = USB_SPEED_UNKNOWN;
+ udc->gadget.max_speed = USB_SPEED_HIGH;
+ udc->creq = udc->reg + AST_UDC_SETUP0;
+
+ /*
+ * Support single stage mode or 32/256 stages descriptor mode.
+ * Set default as Descriptor Mode.
+ */
+ udc->desc_mode = AST_UDC_DESC_MODE;
+
+ dev_info(&pdev->dev, "DMA %s\n", udc->desc_mode ?
+ "descriptor mode" : "single mode");
+
+ INIT_LIST_HEAD(&udc->gadget.ep_list);
+ INIT_LIST_HEAD(&udc->gadget.ep0->ep_list);
+
+ /* Initialized udc ep */
+ ast_udc_init_ep(udc);
+
+ /* Initialized udc device */
+ ast_udc_init_dev(udc);
+
+ /* Initialized udc hardware */
+ ast_udc_init_hw(udc);
+
+ /* Find interrupt and install handler */
+ udc->irq = platform_get_irq(pdev, 0);
+ if (udc->irq < 0) {
+ dev_err(&pdev->dev, "Failed to get interrupt\n");
+ rc = udc->irq;
+ goto err;
+ }
+
+ rc = devm_request_irq(&pdev->dev, udc->irq, ast_udc_isr, 0,
+ KBUILD_MODNAME, udc);
+ if (rc) {
+ dev_err(&pdev->dev, "Failed to request interrupt\n");
+ goto err;
+ }
+
+ rc = usb_add_gadget_udc(&pdev->dev, &udc->gadget);
+ if (rc) {
+ dev_err(&pdev->dev, "Failed to add gadget udc\n");
+ goto err;
+ }
+
+ dev_info(&pdev->dev, "Initialized udc in USB%s mode\n",
+ udc->force_usb1 ? "1" : "2");
+
+ return 0;
+
+err:
+ dev_err(&pdev->dev, "Failed to udc probe, rc:0x%x\n", rc);
+ ast_udc_remove(pdev);
+
+ return rc;
+}
+
+static const struct of_device_id ast_udc_of_dt_ids[] = {
+ { .compatible = "aspeed,ast2600-udc", },
+ {}
+};
+
+MODULE_DEVICE_TABLE(of, ast_udc_of_dt_ids);
+
+static struct platform_driver ast_udc_driver = {
+ .probe = ast_udc_probe,
+ .remove = ast_udc_remove,
+ .driver = {
+ .name = KBUILD_MODNAME,
+ .of_match_table = ast_udc_of_dt_ids,
+ },
+};
+
+module_platform_driver(ast_udc_driver);
+
+MODULE_DESCRIPTION("ASPEED UDC driver");
+MODULE_AUTHOR("Neal Liu <[email protected]>");
+MODULE_LICENSE("GPL");
--
2.25.1



2022-05-16 14:12:21

by kernel test robot

[permalink] [raw]
Subject: Re: [PATCH 1/3] usb: gadget: add Aspeed ast2600 udc driver

Hi Neal,

I love your patch! Perhaps something to improve:

[auto build test WARNING on usb/usb-testing]
[also build test WARNING on robh/for-next v5.18-rc7 next-20220513]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url: https://github.com/intel-lab-lkp/linux/commits/Neal-Liu/add-Aspeed-udc-driver-for-ast2600/20220513-150314
base: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-testing
config: openrisc-randconfig-s031-20220516 (https://download.01.org/0day-ci/archive/20220516/[email protected]/config)
compiler: or1k-linux-gcc (GCC) 11.3.0
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# apt-get install sparse
# sparse version: v0.6.4-dirty
# https://github.com/intel-lab-lkp/linux/commit/272ae26f9fe89f60d584cf445431d0fa566eb24b
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review Neal-Liu/add-Aspeed-udc-driver-for-ast2600/20220513-150314
git checkout 272ae26f9fe89f60d584cf445431d0fa566eb24b
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.3.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=openrisc SHELL=/bin/bash drivers/usb/gadget/udc/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <[email protected]>


sparse warnings: (new ones prefixed by >>)
drivers/usb/gadget/udc/aspeed_udc.c:1009:34: sparse: sparse: restricted __le16 degrades to integer
>> drivers/usb/gadget/udc/aspeed_udc.c:1037:32: sparse: sparse: incorrect type in argument 2 (different address spaces) @@ expected void const volatile [noderef] __iomem *addr @@ got struct usb_ctrlrequest *creq @@
drivers/usb/gadget/udc/aspeed_udc.c:1037:32: sparse: expected void const volatile [noderef] __iomem *addr
drivers/usb/gadget/udc/aspeed_udc.c:1037:32: sparse: got struct usb_ctrlrequest *creq
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: sparse: incorrect type in argument 1 (different base types) @@ expected unsigned int [usertype] value @@ got restricted __le16 [addressable] [usertype] wValue @@
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: expected unsigned int [usertype] value
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: got restricted __le16 [addressable] [usertype] wValue
drivers/usb/gadget/udc/aspeed_udc.c:1070:37: sparse: sparse: restricted __le16 degrades to integer
drivers/usb/gadget/udc/aspeed_udc.c:1075:37: sparse: sparse: restricted __le16 degrades to integer
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: sparse: incorrect type in assignment (different address spaces) @@ expected struct usb_ctrlrequest *creq @@ got void [noderef] __iomem * @@
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: expected struct usb_ctrlrequest *creq
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: got void [noderef] __iomem *
drivers/usb/gadget/udc/aspeed_udc.c:619:38: sparse: sparse: cast truncates bits from constant value (80 becomes 0)
drivers/usb/gadget/udc/aspeed_udc.c:625:12: sparse: sparse: context imbalance in 'ast_udc_ep_queue' - different lock contexts for basic block

vim +1037 drivers/usb/gadget/udc/aspeed_udc.c

1027
1028 static void ast_udc_ep0_handle_setup(struct ast_udc_dev *udc)
1029 {
1030 struct ast_udc_ep *ep = &udc->ep[0];
1031 struct ast_udc_request *req;
1032 struct usb_ctrlrequest crq;
1033 int req_num = 0;
1034 u16 ep_num = 0;
1035 int rc;
1036
> 1037 memcpy_fromio(&crq, udc->creq, sizeof(crq));
1038
1039 SETUP_DBG(udc, "SETEUP packet: %02x/%02x/%04x/%04x/%04x\n",
1040 crq.bRequestType, crq.bRequest, le16_to_cpu(crq.wValue),
1041 le16_to_cpu(crq.wIndex), le16_to_cpu(crq.wLength));
1042
1043 /*
1044 * Cleanup ep0 request(s) in queue because
1045 * there is a new control setup comes.
1046 */
1047 list_for_each_entry(req, &udc->ep[0].queue, queue) {
1048 req_num++;
1049 EP_DBG(ep, "there is req %p in ep0 queue !\n", req);
1050 }
1051
1052 if (req_num)
1053 ast_udc_nuke(&udc->ep[0], -ETIMEDOUT);
1054
1055 udc->ep[0].dir_in = crq.bRequestType & USB_DIR_IN;
1056
1057 if ((crq.bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) {
1058 switch (crq.bRequest) {
1059 case USB_REQ_SET_ADDRESS:
1060 if (ast_udc_read(udc, AST_UDC_STS) & UDC_STS_HIGHSPEED)
1061 udc->gadget.speed = USB_SPEED_HIGH;
1062 else
1063 udc->gadget.speed = USB_SPEED_FULL;
1064
1065 SETUP_DBG(udc, "set addr: 0x%x\n", crq.wValue);
1066 ast_udc_write(udc, crq.wValue, AST_UDC_CONFIG);
1067 goto req_complete;
1068
1069 case USB_REQ_CLEAR_FEATURE:
1070 ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
1071 SETUP_DBG(udc, "ep%d: CLEAR FEATURE\n", ep_num);
1072 goto req_driver;
1073
1074 case USB_REQ_SET_FEATURE:
1075 ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
1076 SETUP_DBG(udc, "ep%d: SET FEATURE\n", ep_num);
1077 goto req_driver;
1078
1079 case USB_REQ_GET_STATUS:
1080 ast_udc_getstatus(udc);
1081 return;
1082
1083 default:
1084 goto req_driver;
1085 }
1086
1087 }
1088
1089 req_driver:
1090 if (udc->driver) {
1091 SETUP_DBG(udc, "Forwarding %s to gadget...\n",
1092 udc->gadget.name);
1093
1094 spin_unlock(&udc->lock);
1095 rc = udc->driver->setup(&udc->gadget, &crq);
1096 spin_lock(&udc->lock);
1097
1098 } else
1099 SETUP_DBG(udc, "No gadget for request !\n");
1100
1101 if (rc >= 0)
1102 return;
1103
1104 /* Stall if gadget failed */
1105 SETUP_DBG(udc, "Stalling, rc:0x%x\n", rc);
1106 ast_udc_write(udc, ast_udc_read(udc, AST_UDC_EP0_CTRL) | EP0_STALL,
1107 AST_UDC_EP0_CTRL);
1108 return;
1109
1110 req_complete:
1111 SETUP_DBG(udc, "ep%d: Sending IN status without data\n", ep_num);
1112 ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
1113 }
1114

--
0-DAY CI Kernel Test Service
https://01.org/lkp

2022-05-16 14:59:26

by kernel test robot

[permalink] [raw]
Subject: Re: [PATCH 1/3] usb: gadget: add Aspeed ast2600 udc driver

Hi Neal,

I love your patch! Perhaps something to improve:

[auto build test WARNING on usb/usb-testing]
[also build test WARNING on robh/for-next balbi-usb/testing/next v5.18-rc7 next-20220513]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url: https://github.com/intel-lab-lkp/linux/commits/Neal-Liu/add-Aspeed-udc-driver-for-ast2600/20220513-150314
base: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-testing
config: sparc-randconfig-s031-20220516 (https://download.01.org/0day-ci/archive/20220516/[email protected]/config)
compiler: sparc-linux-gcc (GCC) 11.3.0
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# apt-get install sparse
# sparse version: v0.6.4-dirty
# https://github.com/intel-lab-lkp/linux/commit/272ae26f9fe89f60d584cf445431d0fa566eb24b
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review Neal-Liu/add-Aspeed-udc-driver-for-ast2600/20220513-150314
git checkout 272ae26f9fe89f60d584cf445431d0fa566eb24b
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.3.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=sparc SHELL=/bin/bash drivers/usb/gadget/udc/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <[email protected]>


sparse warnings: (new ones prefixed by >>)
>> drivers/usb/gadget/udc/aspeed_udc.c:1009:34: sparse: sparse: restricted __le16 degrades to integer
>> drivers/usb/gadget/udc/aspeed_udc.c:1037:9: sparse: sparse: incorrect type in argument 2 (different address spaces) @@ expected void const volatile [noderef] __iomem *src @@ got struct usb_ctrlrequest *creq @@
drivers/usb/gadget/udc/aspeed_udc.c:1037:9: sparse: expected void const volatile [noderef] __iomem *src
drivers/usb/gadget/udc/aspeed_udc.c:1037:9: sparse: got struct usb_ctrlrequest *creq
>> drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: sparse: incorrect type in argument 1 (different base types) @@ expected unsigned int [usertype] value @@ got restricted __le16 [addressable] [usertype] wValue @@
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: expected unsigned int [usertype] value
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: got restricted __le16 [addressable] [usertype] wValue
drivers/usb/gadget/udc/aspeed_udc.c:1070:37: sparse: sparse: restricted __le16 degrades to integer
drivers/usb/gadget/udc/aspeed_udc.c:1075:37: sparse: sparse: restricted __le16 degrades to integer
>> drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: sparse: incorrect type in assignment (different address spaces) @@ expected struct usb_ctrlrequest *creq @@ got void [noderef] __iomem * @@
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: expected struct usb_ctrlrequest *creq
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: got void [noderef] __iomem *
>> drivers/usb/gadget/udc/aspeed_udc.c:619:38: sparse: sparse: cast truncates bits from constant value (80 becomes 0)
drivers/usb/gadget/udc/aspeed_udc.c:625:12: sparse: sparse: context imbalance in 'ast_udc_ep_queue' - different lock contexts for basic block

vim +1009 drivers/usb/gadget/udc/aspeed_udc.c

994
995 static void ast_udc_getstatus(struct ast_udc_dev *udc)
996 {
997 struct ast_udc_ep *ep;
998 u16 status = 0;
999 int epnum;
1000
1001 switch (udc->creq->bRequestType & USB_RECIP_MASK) {
1002 case USB_RECIP_DEVICE:
1003 /* Get device status */
1004 status = 1 << USB_DEVICE_SELF_POWERED;
1005 break;
1006 case USB_RECIP_INTERFACE:
1007 break;
1008 case USB_RECIP_ENDPOINT:
> 1009 epnum = udc->creq->wIndex & USB_ENDPOINT_NUMBER_MASK;
1010 status = udc->ep[epnum].stopped;
1011 break;
1012 default:
1013 goto stall;
1014 }
1015
1016 ep = &udc->ep[epnum];
1017 EP_DBG(ep, "status: 0x%x\n", status);
1018 ast_udc_ep0_data_tx(udc, (u8 *)&status, sizeof(status));
1019
1020 return;
1021
1022 stall:
1023 EP_DBG(ep, "Can't respond request\n");
1024 ast_udc_write(udc, ast_udc_read(udc, AST_UDC_EP0_CTRL) | EP0_STALL,
1025 AST_UDC_EP0_CTRL);
1026 }
1027
1028 static void ast_udc_ep0_handle_setup(struct ast_udc_dev *udc)
1029 {
1030 struct ast_udc_ep *ep = &udc->ep[0];
1031 struct ast_udc_request *req;
1032 struct usb_ctrlrequest crq;
1033 int req_num = 0;
1034 u16 ep_num = 0;
1035 int rc;
1036
> 1037 memcpy_fromio(&crq, udc->creq, sizeof(crq));
1038
1039 SETUP_DBG(udc, "SETEUP packet: %02x/%02x/%04x/%04x/%04x\n",
1040 crq.bRequestType, crq.bRequest, le16_to_cpu(crq.wValue),
1041 le16_to_cpu(crq.wIndex), le16_to_cpu(crq.wLength));
1042
1043 /*
1044 * Cleanup ep0 request(s) in queue because
1045 * there is a new control setup comes.
1046 */
1047 list_for_each_entry(req, &udc->ep[0].queue, queue) {
1048 req_num++;
1049 EP_DBG(ep, "there is req %p in ep0 queue !\n", req);
1050 }
1051
1052 if (req_num)
1053 ast_udc_nuke(&udc->ep[0], -ETIMEDOUT);
1054
1055 udc->ep[0].dir_in = crq.bRequestType & USB_DIR_IN;
1056
1057 if ((crq.bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) {
1058 switch (crq.bRequest) {
1059 case USB_REQ_SET_ADDRESS:
1060 if (ast_udc_read(udc, AST_UDC_STS) & UDC_STS_HIGHSPEED)
1061 udc->gadget.speed = USB_SPEED_HIGH;
1062 else
1063 udc->gadget.speed = USB_SPEED_FULL;
1064
1065 SETUP_DBG(udc, "set addr: 0x%x\n", crq.wValue);
> 1066 ast_udc_write(udc, crq.wValue, AST_UDC_CONFIG);
1067 goto req_complete;
1068
1069 case USB_REQ_CLEAR_FEATURE:
1070 ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
1071 SETUP_DBG(udc, "ep%d: CLEAR FEATURE\n", ep_num);
1072 goto req_driver;
1073
1074 case USB_REQ_SET_FEATURE:
1075 ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
1076 SETUP_DBG(udc, "ep%d: SET FEATURE\n", ep_num);
1077 goto req_driver;
1078
1079 case USB_REQ_GET_STATUS:
1080 ast_udc_getstatus(udc);
1081 return;
1082
1083 default:
1084 goto req_driver;
1085 }
1086
1087 }
1088
1089 req_driver:
1090 if (udc->driver) {
1091 SETUP_DBG(udc, "Forwarding %s to gadget...\n",
1092 udc->gadget.name);
1093
1094 spin_unlock(&udc->lock);
1095 rc = udc->driver->setup(&udc->gadget, &crq);
1096 spin_lock(&udc->lock);
1097
1098 } else
1099 SETUP_DBG(udc, "No gadget for request !\n");
1100
1101 if (rc >= 0)
1102 return;
1103
1104 /* Stall if gadget failed */
1105 SETUP_DBG(udc, "Stalling, rc:0x%x\n", rc);
1106 ast_udc_write(udc, ast_udc_read(udc, AST_UDC_EP0_CTRL) | EP0_STALL,
1107 AST_UDC_EP0_CTRL);
1108 return;
1109
1110 req_complete:
1111 SETUP_DBG(udc, "ep%d: Sending IN status without data\n", ep_num);
1112 ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
1113 }
1114

--
0-DAY CI Kernel Test Service
https://01.org/lkp

2022-05-17 03:35:14

by kernel test robot

[permalink] [raw]
Subject: Re: [PATCH 1/3] usb: gadget: add Aspeed ast2600 udc driver

Hi Neal,

I love your patch! Perhaps something to improve:

[auto build test WARNING on usb/usb-testing]
[also build test WARNING on robh/for-next v5.18-rc7]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url: https://github.com/intel-lab-lkp/linux/commits/Neal-Liu/add-Aspeed-udc-driver-for-ast2600/20220513-150314
base: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-testing
config: mips-randconfig-s032-20220516 (https://download.01.org/0day-ci/archive/20220517/[email protected]/config)
compiler: mipsel-linux-gcc (GCC) 11.3.0
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# apt-get install sparse
# sparse version: v0.6.4-dirty
# https://github.com/intel-lab-lkp/linux/commit/272ae26f9fe89f60d584cf445431d0fa566eb24b
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review Neal-Liu/add-Aspeed-udc-driver-for-ast2600/20220513-150314
git checkout 272ae26f9fe89f60d584cf445431d0fa566eb24b
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.3.0 make.cross C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__' O=build_dir ARCH=mips SHELL=/bin/bash drivers/usb/gadget/udc/

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <[email protected]>


sparse warnings: (new ones prefixed by >>)
command-line: note: in included file:
builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQUIRE redefined
builtin:0:0: sparse: this was the original definition
builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_SEQ_CST redefined
builtin:0:0: sparse: this was the original definition
builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_ACQ_REL redefined
builtin:0:0: sparse: this was the original definition
builtin:1:9: sparse: sparse: preprocessor token __ATOMIC_RELEASE redefined
builtin:0:0: sparse: this was the original definition
drivers/usb/gadget/udc/aspeed_udc.c:1009:34: sparse: sparse: restricted __le16 degrades to integer
drivers/usb/gadget/udc/aspeed_udc.c:1037:32: sparse: sparse: incorrect type in argument 2 (different address spaces) @@ expected void const volatile [noderef] __iomem *src @@ got struct usb_ctrlrequest *creq @@
drivers/usb/gadget/udc/aspeed_udc.c:1037:32: sparse: expected void const volatile [noderef] __iomem *src
drivers/usb/gadget/udc/aspeed_udc.c:1037:32: sparse: got struct usb_ctrlrequest *creq
>> drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: sparse: incorrect type in argument 1 (different base types) @@ expected unsigned int [usertype] val @@ got restricted __le16 [addressable] [usertype] wValue @@
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: expected unsigned int [usertype] val
drivers/usb/gadget/udc/aspeed_udc.c:1066:25: sparse: got restricted __le16 [addressable] [usertype] wValue
drivers/usb/gadget/udc/aspeed_udc.c:1070:37: sparse: sparse: restricted __le16 degrades to integer
drivers/usb/gadget/udc/aspeed_udc.c:1075:37: sparse: sparse: restricted __le16 degrades to integer
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: sparse: incorrect type in assignment (different address spaces) @@ expected struct usb_ctrlrequest *creq @@ got void [noderef] __iomem * @@
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: expected struct usb_ctrlrequest *creq
drivers/usb/gadget/udc/aspeed_udc.c:1518:19: sparse: got void [noderef] __iomem *
drivers/usb/gadget/udc/aspeed_udc.c:619:38: sparse: sparse: cast truncates bits from constant value (80 becomes 0)
drivers/usb/gadget/udc/aspeed_udc.c:625:12: sparse: sparse: context imbalance in 'ast_udc_ep_queue' - different lock contexts for basic block

vim +1066 drivers/usb/gadget/udc/aspeed_udc.c

1027
1028 static void ast_udc_ep0_handle_setup(struct ast_udc_dev *udc)
1029 {
1030 struct ast_udc_ep *ep = &udc->ep[0];
1031 struct ast_udc_request *req;
1032 struct usb_ctrlrequest crq;
1033 int req_num = 0;
1034 u16 ep_num = 0;
1035 int rc;
1036
1037 memcpy_fromio(&crq, udc->creq, sizeof(crq));
1038
1039 SETUP_DBG(udc, "SETEUP packet: %02x/%02x/%04x/%04x/%04x\n",
1040 crq.bRequestType, crq.bRequest, le16_to_cpu(crq.wValue),
1041 le16_to_cpu(crq.wIndex), le16_to_cpu(crq.wLength));
1042
1043 /*
1044 * Cleanup ep0 request(s) in queue because
1045 * there is a new control setup comes.
1046 */
1047 list_for_each_entry(req, &udc->ep[0].queue, queue) {
1048 req_num++;
1049 EP_DBG(ep, "there is req %p in ep0 queue !\n", req);
1050 }
1051
1052 if (req_num)
1053 ast_udc_nuke(&udc->ep[0], -ETIMEDOUT);
1054
1055 udc->ep[0].dir_in = crq.bRequestType & USB_DIR_IN;
1056
1057 if ((crq.bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) {
1058 switch (crq.bRequest) {
1059 case USB_REQ_SET_ADDRESS:
1060 if (ast_udc_read(udc, AST_UDC_STS) & UDC_STS_HIGHSPEED)
1061 udc->gadget.speed = USB_SPEED_HIGH;
1062 else
1063 udc->gadget.speed = USB_SPEED_FULL;
1064
1065 SETUP_DBG(udc, "set addr: 0x%x\n", crq.wValue);
> 1066 ast_udc_write(udc, crq.wValue, AST_UDC_CONFIG);
1067 goto req_complete;
1068
1069 case USB_REQ_CLEAR_FEATURE:
1070 ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
1071 SETUP_DBG(udc, "ep%d: CLEAR FEATURE\n", ep_num);
1072 goto req_driver;
1073
1074 case USB_REQ_SET_FEATURE:
1075 ep_num = crq.wIndex & USB_ENDPOINT_NUMBER_MASK;
1076 SETUP_DBG(udc, "ep%d: SET FEATURE\n", ep_num);
1077 goto req_driver;
1078
1079 case USB_REQ_GET_STATUS:
1080 ast_udc_getstatus(udc);
1081 return;
1082
1083 default:
1084 goto req_driver;
1085 }
1086
1087 }
1088
1089 req_driver:
1090 if (udc->driver) {
1091 SETUP_DBG(udc, "Forwarding %s to gadget...\n",
1092 udc->gadget.name);
1093
1094 spin_unlock(&udc->lock);
1095 rc = udc->driver->setup(&udc->gadget, &crq);
1096 spin_lock(&udc->lock);
1097
1098 } else
1099 SETUP_DBG(udc, "No gadget for request !\n");
1100
1101 if (rc >= 0)
1102 return;
1103
1104 /* Stall if gadget failed */
1105 SETUP_DBG(udc, "Stalling, rc:0x%x\n", rc);
1106 ast_udc_write(udc, ast_udc_read(udc, AST_UDC_EP0_CTRL) | EP0_STALL,
1107 AST_UDC_EP0_CTRL);
1108 return;
1109
1110 req_complete:
1111 SETUP_DBG(udc, "ep%d: Sending IN status without data\n", ep_num);
1112 ast_udc_write(udc, EP0_TX_BUFF_RDY, AST_UDC_EP0_CTRL);
1113 }
1114

--
0-DAY CI Kernel Test Service
https://01.org/lkp