2022-05-26 02:55:48

by Viorel Suman (OSS)

[permalink] [raw]
Subject: [PATCH] net: phy: at803x: disable WOL at probe

From: Viorel Suman <[email protected]>

Before 7beecaf7d507b ("net: phy: at803x: improve the WOL feature") patch
"at803x_get_wol" implementation used AT803X_INTR_ENABLE_WOL value to set
WAKE_MAGIC flag, and now AT803X_WOL_EN value is used for the same purpose.
The problem here is that the value of these two bits is different after
hardware reset: AT803X_INTR_ENABLE_WOL=0 after hardware reset, but
AT803X_WOL_EN=1. So now, if called right after boot, "at803x_get_wol" will
set WAKE_MAGIC flag, even if WOL function is not enabled via
"at803x_set_wol" call. The patch disables WOL function on probe using
"at803x_set_wol" call thus the behavior is consistent.

Fixes: 7beecaf7d507b ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Viorel Suman <[email protected]>
---
drivers/net/phy/at803x.c | 16 +++++++++++++---
1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 73926006d319..6277d1b1d814 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -443,10 +443,10 @@ static int at803x_set_wol(struct phy_device *phydev,
AT803X_LOC_MAC_ADDR_0_15_OFFSET,
};

- if (!ndev)
- return -ENODEV;
-
if (wol->wolopts & WAKE_MAGIC) {
+ if (!ndev)
+ return -ENODEV;
+
mac = (const u8 *) ndev->dev_addr;

if (!is_valid_ether_addr(mac))
@@ -857,6 +857,9 @@ static int at803x_probe(struct phy_device *phydev)
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
int mode_cfg;
+ struct ethtool_wolinfo wol = {
+ .wolopts = 0,
+ };

if (ccr < 0)
goto err;
@@ -872,6 +875,13 @@ static int at803x_probe(struct phy_device *phydev)
priv->is_fiber = true;
break;
}
+
+ /* Disable WOL by default */
+ ret = at803x_set_wol(phydev, &wol);
+ if (ret < 0) {
+ phydev_err(phydev, "failed to disable WOL on probe: %d\n", ret);
+ return ret;
+ }
}

return 0;
--
2.35.3



2022-05-28 03:10:36

by Viorel Suman

[permalink] [raw]
Subject: Re: [PATCH] net: phy: at803x: disable WOL at probe

On 22-05-26 21:00:44, Jakub Kicinski wrote:
> On Wed, 25 May 2022 13:36:57 +0300 Viorel Suman (OSS) wrote:
> > diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
> > index 73926006d319..6277d1b1d814 100644
> > --- a/drivers/net/phy/at803x.c
> > +++ b/drivers/net/phy/at803x.c
> > @@ -443,10 +443,10 @@ static int at803x_set_wol(struct phy_device *phydev,
> > AT803X_LOC_MAC_ADDR_0_15_OFFSET,
> > };
> >
> > - if (!ndev)
> > - return -ENODEV;
> > -
> > if (wol->wolopts & WAKE_MAGIC) {
> > + if (!ndev)
> > + return -ENODEV;
>
> Please move the ndev variable into the scope.
> It'll make it clear that it can't be used elsewhere
> in this function.

Thank you for review, done in v2.

>
> > mac = (const u8 *) ndev->dev_addr;
> >
> > if (!is_valid_ether_addr(mac))
> > @@ -857,6 +857,9 @@ static int at803x_probe(struct phy_device *phydev)
> > if (phydev->drv->phy_id == ATH8031_PHY_ID) {
> > int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
> > int mode_cfg;
> > + struct ethtool_wolinfo wol = {
> > + .wolopts = 0,
> > + };
> >
> > if (ccr < 0)
> > goto err;
> > @@ -872,6 +875,13 @@ static int at803x_probe(struct phy_device *phydev)
> > priv->is_fiber = true;
> > break;
> > }
> > +
> > + /* Disable WOL by default */
> > + ret = at803x_set_wol(phydev, &wol);
> > + if (ret < 0) {
> > + phydev_err(phydev, "failed to disable WOL on probe: %d\n", ret);
> > + return ret;
>
> Don't you need to goto err; here?

Missed err section indeed, thanks. Fixed in v2.

>
> > + }
> > }
> >
> > return 0;

2022-05-28 19:08:08

by Jakub Kicinski

[permalink] [raw]
Subject: Re: [PATCH] net: phy: at803x: disable WOL at probe

On Wed, 25 May 2022 13:36:57 +0300 Viorel Suman (OSS) wrote:
> diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
> index 73926006d319..6277d1b1d814 100644
> --- a/drivers/net/phy/at803x.c
> +++ b/drivers/net/phy/at803x.c
> @@ -443,10 +443,10 @@ static int at803x_set_wol(struct phy_device *phydev,
> AT803X_LOC_MAC_ADDR_0_15_OFFSET,
> };
>
> - if (!ndev)
> - return -ENODEV;
> -
> if (wol->wolopts & WAKE_MAGIC) {
> + if (!ndev)
> + return -ENODEV;

Please move the ndev variable into the scope.
It'll make it clear that it can't be used elsewhere
in this function.

> mac = (const u8 *) ndev->dev_addr;
>
> if (!is_valid_ether_addr(mac))
> @@ -857,6 +857,9 @@ static int at803x_probe(struct phy_device *phydev)
> if (phydev->drv->phy_id == ATH8031_PHY_ID) {
> int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
> int mode_cfg;
> + struct ethtool_wolinfo wol = {
> + .wolopts = 0,
> + };
>
> if (ccr < 0)
> goto err;
> @@ -872,6 +875,13 @@ static int at803x_probe(struct phy_device *phydev)
> priv->is_fiber = true;
> break;
> }
> +
> + /* Disable WOL by default */
> + ret = at803x_set_wol(phydev, &wol);
> + if (ret < 0) {
> + phydev_err(phydev, "failed to disable WOL on probe: %d\n", ret);
> + return ret;

Don't you need to goto err; here?

> + }
> }
>
> return 0;