From: Frank Wunderlich <[email protected]>
Add Nodes to Bananapi-R2-Pro board to support PCIe v3 and
set PCIe related regulators to always on.
Suggested-by: Peter Geis <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
---
v4:
- change u8 lane-map to u32 data-lanes
v3:
- squash lane-map over bifurcation property
- add comment which slot is M2 and which one if mPCIe
- fixes from Peter:
- drop regulator-always-on/regulator-boot-on from regulators
- increase startup-delay-us for regulators
- set phy-mode on PCIe3-phy
- add num-lanes to PCIe overrides
- add usb node for to PCIe/m2
- move lane-map from PCIe controller to PCIe-phy
v2:
- underscores in nodenames
- rockchip,bifurcation to vendor unspecific bifurcation
- fix trailing space
---
.../boot/dts/rockchip/rk3568-bpi-r2-pro.dts | 90 +++++++++++++++++++
1 file changed, 90 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
index 40cf2236c0b6..dd688019ca49 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
@@ -74,6 +74,62 @@ vcc5v0_sys: vcc5v0-sys {
vin-supply = <&dc_12v>;
};
+ pcie30_avdd0v9: pcie30-avdd0v9 {
+ compatible = "regulator-fixed";
+ regulator-name = "pcie30_avdd0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ pcie30_avdd1v8: pcie30-avdd1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "pcie30_avdd1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* pi6c pcie clock generator feeds both ports */
+ vcc3v3_pi6c_05: vcc3v3-pi6c-05-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <200000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ /* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+ vcc3v3_minipcie: vcc3v3-minipcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_minipcie";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc3v3_pi6c_05>;
+ };
+
+ /* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+ vcc3v3_ngff: vcc3v3-ngff-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_ngff";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc3v3_pi6c_05>;
+ };
+
vcc5v0_usb: vcc5v0_usb {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_usb";
@@ -401,6 +457,27 @@ rgmii_phy1: ethernet-phy@0 {
};
};
+&pcie30phy {
+ data-lanes = <1 2>;
+ status = "okay";
+};
+
+&pcie3x1 {
+ /* M.2 slot */
+ num-lanes = <1>;
+ reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_ngff>;
+ status = "okay";
+};
+
+&pcie3x2 {
+ /* mPCIe slot */
+ num-lanes = <1>;
+ reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_minipcie>;
+ status = "okay";
+};
+
&pinctrl {
leds {
blue_led_pin: blue-led-pin {
@@ -587,3 +664,16 @@ &usb2phy0_otg {
phy-supply = <&vcc5v0_usb_otg>;
status = "okay";
};
+
+&usb2phy1 {
+ /* USB for PCIe/M2 */
+ status = "okay";
+};
+
+&usb2phy1_host {
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ status = "okay";
+};
--
2.34.1