From: Andy Yan <[email protected]>
EAIDK-610 is from OPEN AI LAB and popularly used by university
students.
Specification:
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- 12V DC Power supply
This patch is test on Armbain and Glodroid with
HDMI/GPU/USB HOST/Type-C ADB/WIFI.
Signed-off-by: Andy Yan <[email protected]>
---
.../devicetree/bindings/arm/rockchip.yaml | 5 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3399-eaidk-610.dts | 899 ++++++++++++++++++
4 files changed, 907 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index cf9eb1e8326a..f1dd87b1544e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -470,6 +470,11 @@ properties:
- const: netxeon,r89
- const: rockchip,rk3288
+ - description: OPEN AI LAB EAIDK-610
+ items:
+ - const: openailab,eaidk-610
+ - const: rockchip,rk3399
+
- description: Orange Pi RK3399 board
items:
- const: rockchip,rk3399-orangepi
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 0496773a3c4d..bc5011d79371 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -907,6 +907,8 @@ patternProperties:
description: On Tat Industrial Company
"^opalkelly,.*":
description: Opal Kelly Incorporated
+ "^openailab,.*":
+ description: openailab.com
"^opencores,.*":
description: OpenCores.org
"^openembed,.*":
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 18d00eae3072..addc8755709b 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -21,6 +21,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-eaidk-610.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
new file mode 100644
index 000000000000..00eee40d646c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
@@ -0,0 +1,899 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+ model = "OPEN AI LAB EAIDK-610";
+ compatible = "openailab,eaidk-610", "rockchip,rk3399";
+
+ aliases {
+ mmc0 = &sdio0;
+ mmc1 = &sdmmc;
+ mmc2 = &sdhci;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 25000 0>;
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7
+ 8 9 10 11 12 13 14 15
+ 16 17 18 19 20 21 22 23
+ 24 25 26 27 28 29 30 31
+ 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47
+ 48 49 50 51 52 53 54 55
+ 56 57 58 59 60 61 62 63
+ 64 65 66 67 68 69 70 71
+ 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87
+ 88 89 90 91 92 93 94 95
+ 96 97 98 99 100 101 102 103
+ 104 105 106 107 108 109 110 111
+ 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127
+ 128 129 130 131 132 133 134 135
+ 136 137 138 139 140 141 142 143
+ 144 145 146 147 148 149 150 151
+ 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167
+ 168 169 170 171 172 173 174 175
+ 176 177 178 179 180 181 182 183
+ 184 185 186 187 188 189 190 191
+ 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207
+ 208 209 210 211 212 213 214 215
+ 216 217 218 219 220 221 222 223
+ 224 225 226 227 228 229 230 231
+ 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247
+ 248 249 250 251 252 253 254 255>;
+ default-brightness-level = <200>;
+ };
+
+ clkin_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "clkin_gmac";
+ #clock-cells = <0>;
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn>;
+
+ power {
+ debounce-interval = <100>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "GPIO Key Power";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_pin>, <&user_led_pin>,
+ <&heartbeat_led_pin>, <&wlan_active_led_pin>,
+ <&bt_active_led_pin>;
+
+ work_led: led-0 {
+ label = "blue:work";
+ default-state = "on";
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ };
+
+ user_led: led-1 {
+ label = "read:user";
+ default-state = "off";
+ gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+ };
+
+ heartbeat_led: led-2 {
+ label = "green:heartbeat";
+ linux,default-trigger = "heartbeat";
+ gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan_active_led: led-3 {
+ label = "yellow:wlan";
+ gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ bt_active_led: led-4 {
+ label = "blue:bt";
+ gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "hci0-power";
+ default-state = "off";
+ };
+ };
+
+ rt5651-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "realtek,rt5651-codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Mic Jack", "MICBIAS1",
+ "IN1P", "Mic Jack",
+ "Headphone Jack", "HPOL",
+ "Headphone Jack", "HPOR";
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&rt5651>;
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+ reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+ };
+
+ /* switched by pmic_sleep */
+ vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ /* For USB3.0 Port1/2 */
+ vcc5v0_host1: vcc5v0-host1-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host1_en>;
+ regulator-name = "vcc5v0_host1";
+ regulator-always-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ /* For USB2.0 Port1/2 */
+ vcc5v0_host3: vcc5v0-host3-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host3_en>;
+ regulator-name = "vcc5v0_host3";
+ regulator-always-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_typec: vcc5v0-typec-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_typec_en>;
+ regulator-name = "vcc5v0_typec";
+ regulator-always-on;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vdd_log: vdd-log {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_RMII_SRC>;
+ assigned-clock-parents = <&clkin_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ tx_delay = <0x28>;
+ rx_delay = <0x11>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_cec>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ vcc10-supply = <&vcc3v3_sys>;
+ vcc11-supply = <&vcc3v3_sys>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_3v0>;
+
+ regulators {
+ vdd_center: DCDC_REG1 {
+ regulator-name = "vdd_center";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-name = "vdd_cpu_l";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG4 {
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc1v8_dvp: LDO_REG1 {
+ regulator-name = "vcc1v8_dvp";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc2v8_dvp: LDO_REG2 {
+ regulator-name = "vcc2v8_dvp";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG3 {
+ regulator-name = "vcc1v8_pmu";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_sdio: LDO_REG4 {
+ regulator-name = "vcc_sdio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcca3v0_codec: LDO_REG5 {
+ regulator-name = "vcca3v0_codec";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v5: LDO_REG6 {
+ regulator-name = "vcc_1v5";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1500000>;
+ };
+ };
+
+ vcca1v8_codec: LDO_REG7 {
+ regulator-name = "vcca1v8_codec";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v0: LDO_REG8 {
+ regulator-name = "vcc_3v0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc3v3_s3: vcc_lan: SWITCH_REG1 {
+ regulator-name = "vcc3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s0: SWITCH_REG2 {
+ regulator-name = "vcc3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu_b: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_b";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel1_pin>;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: regulator@41 {
+ compatible = "silergy,syr828";
+ reg = <0x41>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_gpu";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel2_pin>;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <1000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c1 {
+ i2c-scl-rising-time-ns = <300>;
+ i2c-scl-falling-time-ns = <15>;
+ status = "okay";
+
+ rt5651: rt5651@1a {
+ compatible = "rockchip,rt5651";
+ reg = <0x1a>;
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ clock-names = "mclk";
+ hp-det-gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
+ spk-con-gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
+};
+
+&i2c3 {
+ i2c-scl-rising-time-ns = <450>;
+ i2c-scl-falling-time-ns = <15>;
+ status = "okay";
+};
+
+&i2c4 {
+ i2c-scl-rising-time-ns = <600>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+
+ fusb0: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fusb0_int>;
+ vbus-supply = <&vcc5v0_typec>;
+ status = "okay";
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "host";
+ label = "USB-C";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ sink-pdos =
+ <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
+ try-power-role = "sink";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc_hs: endpoint {
+ remote-endpoint =
+ <&u2phy0_typec_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usbc_ss: endpoint {
+ remote-endpoint =
+ <&tcphy0_typec_ss>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2s1 {
+ rockchip,playback-channels = <2>;
+ rockchip,capture-channels = <2>;
+ status = "okay";
+};
+
+&i2s2 {
+ status = "okay";
+};
+
+&io_domains {
+ status = "okay";
+
+ audio-supply = <&vcca1v8_codec>;
+ bt656-supply = <&vcc_3v0>;
+ gpio1830-supply = <&vcc_3v0>;
+ sdmmc-supply = <&vcc_sdio>;
+};
+
+&pmu_io_domains {
+ status = "okay";
+
+ pmu1830-supply = <&vcc_3v0>;
+};
+
+&pinctrl {
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ fusb302x {
+ fusb0_int: fusb0-int {
+ rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ lcd-panel {
+ lcd_panel_reset: lcd-panel-reset {
+ rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ work_led_pin: work-led-pin {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ user_led_pin: user-led-pin {
+ rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ heartbeat_led_pin: heartbeat-led-pin {
+ rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wlan_active_led_pin: wlan-led-pin {
+ rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_active_led_pin: bt-led-pin {
+ rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ vsel1_pin: vsel1-pin {
+ rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ vsel2_pin: vsel2-pin {
+ rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ rt5651 {
+ rt5651_hpcon: rt5640-hpcon {
+ rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-typec {
+ vcc5v0_typec_en: vcc5v0_typec_en {
+ rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ vcc5v0_host3_en: vcc5v0-host3-en {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_host1_en: vcc5v0-host1-en {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_host_wake_l: wifi-host-wake-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca1v8_s3>;
+ status = "okay";
+};
+
+&sdio0 {
+ /* WiFi & BT combo module AMPAK AP6255 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ clock-frequency = <50000000>;
+ cap-sdio-irq;
+ cap-sd-highspeed;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+ sd-uhs-sdr104;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+ interrupt-names = "host-wake";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_host_wake_l>;
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ max-frequency = <150000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&tcphy0 {
+ status = "okay";
+};
+
+&tcphy0_usb3 {
+ port {
+ tcphy0_typec_ss: endpoint {
+ remote-endpoint = <&usbc_ss>;
+ };
+ };
+};
+
+&tcphy1 {
+ status = "okay";
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_host3>;
+ status = "okay";
+ };
+
+ port {
+ u2phy0_typec_hs: endpoint {
+ remote-endpoint = <&usbc_hs>;
+ };
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host3>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts>;
+ status = "disabled";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
--
2.34.1
On Sun, Jul 03, 2022 at 08:07:06PM +0800, [email protected] wrote:
> From: Andy Yan <[email protected]>
>
> EAIDK-610 is from OPEN AI LAB and popularly used by university
> students.
>
> Specification:
> - Rockchip RK3399
> - LPDDR3 4GB
> - TF sd scard slot
> - eMMC
> - AP6255 for WiFi + BT
> - Gigabit ethernet
> - HDMI out
> - 40 pin header
> - USB 2.0 x 2
> - USB 3.0 x 1
> - USB 3.0 Type-C x 1
> - 12V DC Power supply
>
> This patch is test on Armbain and Glodroid with
> HDMI/GPU/USB HOST/Type-C ADB/WIFI.
>
> Signed-off-by: Andy Yan <[email protected]>
> ---
> .../devicetree/bindings/arm/rockchip.yaml | 5 +
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
Bindings should be a separate patch.
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3399-eaidk-610.dts | 899 ++++++++++++++++++
> 4 files changed, 907 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
> index cf9eb1e8326a..f1dd87b1544e 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.yaml
> +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
> @@ -470,6 +470,11 @@ properties:
> - const: netxeon,r89
> - const: rockchip,rk3288
>
> + - description: OPEN AI LAB EAIDK-610
> + items:
> + - const: openailab,eaidk-610
> + - const: rockchip,rk3399
> +
> - description: Orange Pi RK3399 board
> items:
> - const: rockchip,rk3399-orangepi
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> index 0496773a3c4d..bc5011d79371 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> @@ -907,6 +907,8 @@ patternProperties:
> description: On Tat Industrial Company
> "^opalkelly,.*":
> description: Opal Kelly Incorporated
> + "^openailab,.*":
> + description: openailab.com
> "^opencores,.*":
> description: OpenCores.org
> "^openembed,.*":
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 18d00eae3072..addc8755709b 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -21,6 +21,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-eaidk-610.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> new file mode 100644
> index 000000000000..00eee40d646c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> @@ -0,0 +1,899 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Fuzhou Rockchip Electronics Co., Ltd.
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/usb/pd.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> + model = "OPEN AI LAB EAIDK-610";
> + compatible = "openailab,eaidk-610", "rockchip,rk3399";
> +
> + aliases {
> + mmc0 = &sdio0;
> + mmc1 = &sdmmc;
> + mmc2 = &sdhci;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 25000 0>;
> + brightness-levels = <
> + 0 1 2 3 4 5 6 7
> + 8 9 10 11 12 13 14 15
> + 16 17 18 19 20 21 22 23
> + 24 25 26 27 28 29 30 31
> + 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47
> + 48 49 50 51 52 53 54 55
> + 56 57 58 59 60 61 62 63
> + 64 65 66 67 68 69 70 71
> + 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87
> + 88 89 90 91 92 93 94 95
> + 96 97 98 99 100 101 102 103
> + 104 105 106 107 108 109 110 111
> + 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127
> + 128 129 130 131 132 133 134 135
> + 136 137 138 139 140 141 142 143
> + 144 145 146 147 148 149 150 151
> + 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167
> + 168 169 170 171 172 173 174 175
> + 176 177 178 179 180 181 182 183
> + 184 185 186 187 188 189 190 191
> + 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207
> + 208 209 210 211 212 213 214 215
> + 216 217 218 219 220 221 222 223
> + 224 225 226 227 228 229 230 231
> + 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247
> + 248 249 250 251 252 253 254 255>;
> + default-brightness-level = <200>;
> + };
> +
> + clkin_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + clock-frequency = <125000000>;
> + clock-output-names = "clkin_gmac";
> + #clock-cells = <0>;
> + };
> +
> + dc_12v: dc-12v {
> + compatible = "regulator-fixed";
> + regulator-name = "dc_12v";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn>;
> +
> + power {
key-power
> + debounce-interval = <100>;
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "GPIO Key Power";
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&work_led_pin>, <&user_led_pin>,
> + <&heartbeat_led_pin>, <&wlan_active_led_pin>,
> + <&bt_active_led_pin>;
> +
> + work_led: led-0 {
> + label = "blue:work";
> + default-state = "on";
> + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> + };
> +
> + user_led: led-1 {
> + label = "read:user";
> + default-state = "off";
> + gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
> + };
> +
> + heartbeat_led: led-2 {
> + label = "green:heartbeat";
> + linux,default-trigger = "heartbeat";
> + gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
> + };
> +
> + wlan_active_led: led-3 {
> + label = "yellow:wlan";
> + gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> +
> + bt_active_led: led-4 {
> + label = "blue:bt";
> + gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "hci0-power";
> + default-state = "off";
> + };
> + };
> +
> + rt5651-sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,name = "realtek,rt5651-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphone Jack";
> + simple-audio-card,routing =
> + "Mic Jack", "MICBIAS1",
> + "IN1P", "Mic Jack",
> + "Headphone Jack", "HPOL",
> + "Headphone Jack", "HPOR";
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1>;
> + };
> + simple-audio-card,codec {
> + sound-dai = <&rt5651>;
> + };
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk808 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> +
> + /*
> + * On the module itself this is one of these (depending
> + * on the actual card populated):
> + * - SDIO_RESET_L_WL_REG_ON
> + * - PDN (power down when low)
> + */
> + reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> + };
> +
> + /* switched by pmic_sleep */
> + vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc1v8_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_1v8>;
> + };
> +
> + vcc3v3_sys: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&dc_12v>;
> + };
> +
> + vcc5v0_sys: vcc5v0-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_12v>;
> + };
> +
> + /* For USB3.0 Port1/2 */
> + vcc5v0_host1: vcc5v0-host1-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_host1_en>;
> + regulator-name = "vcc5v0_host1";
> + regulator-always-on;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + /* For USB2.0 Port1/2 */
> + vcc5v0_host3: vcc5v0-host3-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_host3_en>;
> + regulator-name = "vcc5v0_host3";
> + regulator-always-on;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc5v0_typec: vcc5v0-typec-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_typec_en>;
> + regulator-name = "vcc5v0_typec";
> + regulator-always-on;
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + vdd_log: vdd-log {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_log";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + };
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_RMII_SRC>;
> + assigned-clock-parents = <&clkin_gmac>;
> + clock_in_out = "input";
> + phy-supply = <&vcc_lan>;
> + phy-mode = "rgmii";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 50000>;
> + tx_delay = <0x28>;
> + rx_delay = <0x11>;
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + ddc-i2c-bus = <&i2c3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hdmi_cec>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>;
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> +
> + vcc1-supply = <&vcc3v3_sys>;
> + vcc2-supply = <&vcc3v3_sys>;
> + vcc3-supply = <&vcc3v3_sys>;
> + vcc4-supply = <&vcc3v3_sys>;
> + vcc6-supply = <&vcc3v3_sys>;
> + vcc7-supply = <&vcc3v3_sys>;
> + vcc8-supply = <&vcc3v3_sys>;
> + vcc9-supply = <&vcc3v3_sys>;
> + vcc10-supply = <&vcc3v3_sys>;
> + vcc11-supply = <&vcc3v3_sys>;
> + vcc12-supply = <&vcc3v3_sys>;
> + vddio-supply = <&vcc_3v0>;
> +
> + regulators {
> + vdd_center: DCDC_REG1 {
> + regulator-name = "vdd_center";
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_l: DCDC_REG2 {
> + regulator-name = "vdd_cpu_l";
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: DCDC_REG4 {
> + regulator-name = "vcc_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc1v8_dvp: LDO_REG1 {
> + regulator-name = "vcc1v8_dvp";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc2v8_dvp: LDO_REG2 {
> + regulator-name = "vcc2v8_dvp";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc1v8_pmu: LDO_REG3 {
> + regulator-name = "vcc1v8_pmu";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_sdio: LDO_REG4 {
> + regulator-name = "vcc_sdio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcca3v0_codec: LDO_REG5 {
> + regulator-name = "vcca3v0_codec";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v5: LDO_REG6 {
> + regulator-name = "vcc_1v5";
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1500000>;
> + };
> + };
> +
> + vcca1v8_codec: LDO_REG7 {
> + regulator-name = "vcca1v8_codec";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v0: LDO_REG8 {
> + regulator-name = "vcc_3v0";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc3v3_s3: vcc_lan: SWITCH_REG1 {
> + regulator-name = "vcc3v3_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_s0: SWITCH_REG2 {
> + regulator-name = "vcc3v3_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu_b: regulator@40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_b";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel1_pin>;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc3v3_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: regulator@41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_gpu";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel2_pin>;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <1000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc3v3_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c1 {
> + i2c-scl-rising-time-ns = <300>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +
> + rt5651: rt5651@1a {
audio-codec@1a
> + compatible = "rockchip,rt5651";
> + reg = <0x1a>;
> + clocks = <&cru SCLK_I2S_8CH_OUT>;
> + clock-names = "mclk";
> + hp-det-gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
> + spk-con-gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> + #sound-dai-cells = <0>;
> + };
> +
> +};
> +
> +&i2c3 {
> + i2c-scl-rising-time-ns = <450>;
> + i2c-scl-falling-time-ns = <15>;
> + status = "okay";
> +};
> +
> +&i2c4 {
> + i2c-scl-rising-time-ns = <600>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> +
> + fusb0: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&fusb0_int>;
> + vbus-supply = <&vcc5v0_typec>;
> + status = "okay";
That's the default, drop.
Rob