There are four modes, and each mode has a table of registers.
Some of the registers are common to all modes, so create new
tables for these common registers to reduce duplicate code.
Signed-off-by: Adam Ford <[email protected]>
---
V3: Change some of the comments to better reflect their description
Add a few more entries to the imx219_common_regs table.
diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index e10af3f74b38..faa5dab3c2ec 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -145,23 +145,61 @@ struct imx219_mode {
struct imx219_reg_list reg_list;
};
-/*
- * Register sets lifted off the i2C interface from the Raspberry Pi firmware
- * driver.
- * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
- */
-static const struct imx219_reg mode_3280x2464_regs[] = {
- {0x0100, 0x00},
+static const struct imx219_reg imx219_common_regs[] = {
+ {0x0100, 0x00}, /* Mode Select */
+
+ /* To Access Addresses 3000-5fff, send the following commands */
{0x30eb, 0x0c},
{0x30eb, 0x05},
{0x300a, 0xff},
{0x300b, 0xff},
{0x30eb, 0x05},
{0x30eb, 0x09},
- {0x0114, 0x01},
- {0x0128, 0x00},
- {0x012a, 0x18},
+
+ /* PLL Clock Table */
+ {0x0301, 0x05}, /* VTPXCK_DIV */
+ {0x0303, 0x01}, /* VTSYSCK_DIV */
+ {0x0304, 0x03}, /* PREPLLCK_VT_DIV 0x03 = AUTO set */
+ {0x0305, 0x03}, /* PREPLLCK_OP_DIV 0x03 = AUTO set */
+ {0x0306, 0x00}, /* PLL_VT_MPY */
+ {0x0307, 0x39},
+ {0x030b, 0x01}, /* OP_SYS_CLK_DIV */
+ {0x030c, 0x00}, /* PLL_OP_MPY */
+ {0x030d, 0x72},
+
+ /* Undocumented registers */
+ {0x455e, 0x00},
+ {0x471e, 0x4b},
+ {0x4767, 0x0f},
+ {0x4750, 0x14},
+ {0x4540, 0x00},
+ {0x47b4, 0x14},
+ {0x4713, 0x30},
+ {0x478b, 0x10},
+ {0x478f, 0x10},
+ {0x4793, 0x10},
+ {0x4797, 0x0e},
+ {0x479b, 0x0e},
+
+ /* Frame Bank Register Group "A" */
+ {0x0162, 0x0d}, /* Line_Length_A */
+ {0x0163, 0x78},
+ {0x0170, 0x01}, /* X_ODD_INC_A */
+ {0x0171, 0x01}, /* Y_ODD_INC_A */
+
+ /* Output setup registers */
+ {0x0114, 0x01}, /* CSI 2-Lane Mode */
+ {0x0128, 0x00}, /* DPHY Auto Mode */
+ {0x012a, 0x18}, /* EXCK_Freq */
{0x012b, 0x00},
+};
+
+/*
+ * Register sets lifted off the i2C interface from the Raspberry Pi firmware
+ * driver.
+ * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
+ */
+static const struct imx219_reg mode_3280x2464_regs[] = {
{0x0164, 0x00},
{0x0165, 0x00},
{0x0166, 0x0c},
@@ -174,53 +212,15 @@ static const struct imx219_reg mode_3280x2464_regs[] = {
{0x016d, 0xd0},
{0x016e, 0x09},
{0x016f, 0xa0},
- {0x0170, 0x01},
- {0x0171, 0x01},
- {0x0174, 0x00},
+ {0x0174, 0x00}, /* No-Binning */
{0x0175, 0x00},
- {0x0301, 0x05},
- {0x0303, 0x01},
- {0x0304, 0x03},
- {0x0305, 0x03},
- {0x0306, 0x00},
- {0x0307, 0x39},
- {0x030b, 0x01},
- {0x030c, 0x00},
- {0x030d, 0x72},
{0x0624, 0x0c},
{0x0625, 0xd0},
{0x0626, 0x09},
{0x0627, 0xa0},
- {0x455e, 0x00},
- {0x471e, 0x4b},
- {0x4767, 0x0f},
- {0x4750, 0x14},
- {0x4540, 0x00},
- {0x47b4, 0x14},
- {0x4713, 0x30},
- {0x478b, 0x10},
- {0x478f, 0x10},
- {0x4793, 0x10},
- {0x4797, 0x0e},
- {0x479b, 0x0e},
- {0x0162, 0x0d},
- {0x0163, 0x78},
};
static const struct imx219_reg mode_1920_1080_regs[] = {
- {0x0100, 0x00},
- {0x30eb, 0x05},
- {0x30eb, 0x0c},
- {0x300a, 0xff},
- {0x300b, 0xff},
- {0x30eb, 0x05},
- {0x30eb, 0x09},
- {0x0114, 0x01},
- {0x0128, 0x00},
- {0x012a, 0x18},
- {0x012b, 0x00},
- {0x0162, 0x0d},
- {0x0163, 0x78},
{0x0164, 0x02},
{0x0165, 0xa8},
{0x0166, 0x0a},
@@ -233,49 +233,15 @@ static const struct imx219_reg mode_1920_1080_regs[] = {
{0x016d, 0x80},
{0x016e, 0x04},
{0x016f, 0x38},
- {0x0170, 0x01},
- {0x0171, 0x01},
- {0x0174, 0x00},
+ {0x0174, 0x00}, /* No-Binning */
{0x0175, 0x00},
- {0x0301, 0x05},
- {0x0303, 0x01},
- {0x0304, 0x03},
- {0x0305, 0x03},
- {0x0306, 0x00},
- {0x0307, 0x39},
- {0x030b, 0x01},
- {0x030c, 0x00},
- {0x030d, 0x72},
{0x0624, 0x07},
{0x0625, 0x80},
{0x0626, 0x04},
{0x0627, 0x38},
- {0x455e, 0x00},
- {0x471e, 0x4b},
- {0x4767, 0x0f},
- {0x4750, 0x14},
- {0x4540, 0x00},
- {0x47b4, 0x14},
- {0x4713, 0x30},
- {0x478b, 0x10},
- {0x478f, 0x10},
- {0x4793, 0x10},
- {0x4797, 0x0e},
- {0x479b, 0x0e},
};
static const struct imx219_reg mode_1640_1232_regs[] = {
- {0x0100, 0x00},
- {0x30eb, 0x0c},
- {0x30eb, 0x05},
- {0x300a, 0xff},
- {0x300b, 0xff},
- {0x30eb, 0x05},
- {0x30eb, 0x09},
- {0x0114, 0x01},
- {0x0128, 0x00},
- {0x012a, 0x18},
- {0x012b, 0x00},
{0x0164, 0x00},
{0x0165, 0x00},
{0x0166, 0x0c},
@@ -288,53 +254,15 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
{0x016d, 0x68},
{0x016e, 0x04},
{0x016f, 0xd0},
- {0x0170, 0x01},
- {0x0171, 0x01},
- {0x0174, 0x01},
+ {0x0174, 0x01}, /* x2-Binning */
{0x0175, 0x01},
- {0x0301, 0x05},
- {0x0303, 0x01},
- {0x0304, 0x03},
- {0x0305, 0x03},
- {0x0306, 0x00},
- {0x0307, 0x39},
- {0x030b, 0x01},
- {0x030c, 0x00},
- {0x030d, 0x72},
{0x0624, 0x06},
{0x0625, 0x68},
{0x0626, 0x04},
{0x0627, 0xd0},
- {0x455e, 0x00},
- {0x471e, 0x4b},
- {0x4767, 0x0f},
- {0x4750, 0x14},
- {0x4540, 0x00},
- {0x47b4, 0x14},
- {0x4713, 0x30},
- {0x478b, 0x10},
- {0x478f, 0x10},
- {0x4793, 0x10},
- {0x4797, 0x0e},
- {0x479b, 0x0e},
- {0x0162, 0x0d},
- {0x0163, 0x78},
};
static const struct imx219_reg mode_640_480_regs[] = {
- {0x0100, 0x00},
- {0x30eb, 0x05},
- {0x30eb, 0x0c},
- {0x300a, 0xff},
- {0x300b, 0xff},
- {0x30eb, 0x05},
- {0x30eb, 0x09},
- {0x0114, 0x01},
- {0x0128, 0x00},
- {0x012a, 0x18},
- {0x012b, 0x00},
- {0x0162, 0x0d},
- {0x0163, 0x78},
{0x0164, 0x03},
{0x0165, 0xe8},
{0x0166, 0x08},
@@ -347,35 +275,12 @@ static const struct imx219_reg mode_640_480_regs[] = {
{0x016d, 0x80},
{0x016e, 0x01},
{0x016f, 0xe0},
- {0x0170, 0x01},
- {0x0171, 0x01},
- {0x0174, 0x03},
+ {0x0174, 0x03}, /* x2-analog binning */
{0x0175, 0x03},
- {0x0301, 0x05},
- {0x0303, 0x01},
- {0x0304, 0x03},
- {0x0305, 0x03},
- {0x0306, 0x00},
- {0x0307, 0x39},
- {0x030b, 0x01},
- {0x030c, 0x00},
- {0x030d, 0x72},
{0x0624, 0x06},
{0x0625, 0x68},
{0x0626, 0x04},
{0x0627, 0xd0},
- {0x455e, 0x00},
- {0x471e, 0x4b},
- {0x4767, 0x0f},
- {0x4750, 0x14},
- {0x4540, 0x00},
- {0x47b4, 0x14},
- {0x4713, 0x30},
- {0x478b, 0x10},
- {0x478f, 0x10},
- {0x4793, 0x10},
- {0x4797, 0x0e},
- {0x479b, 0x0e},
};
static const struct imx219_reg raw8_framefmt_regs[] = {
@@ -1041,6 +946,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
if (ret < 0)
return ret;
+ /* Send all registers that are common to all modes */
+ ret = imx219_write_regs(imx219, imx219_common_regs, ARRAY_SIZE(imx219_common_regs));
+ if (ret) {
+ dev_err(&client->dev, "%s failed to send mfg header\n", __func__);
+ goto err_rpm_put;
+ }
+
/* Apply default values of current mode */
reg_list = &imx219->mode->reg_list;
ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
--
2.34.1
The imx219 camera is capable of either two-lane or four-lane
operation. When operating in four-lane, both the pixel rate and
link frequency change. Regardless of the mode, however, both
frequencies remain fixed.
Helper functions are needed to read and set pixel and link frequencies
which also reduces the number of fixed registers in the table of modes.
Since the link frequency and number of lanes is extracted from the
endpoint, move the endpoint handling into the probe function and
out of the imx219_check_hwcfg. This simplifies the imx219_check_hwcfg
just a bit.
Signed-off-by: Adam Ford <[email protected]>
---
V3: Keep the helper function doing the link and lane parsing to
keep th probe function small.
diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index faa5dab3c2ec..bb4125e7e113 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -42,10 +42,16 @@
/* External clock frequency is 24.0M */
#define IMX219_XCLK_FREQ 24000000
-/* Pixel rate is fixed at 182.4M for all the modes */
+/* Pixel rate is fixed for all the modes */
#define IMX219_PIXEL_RATE 182400000
+#define IMX219_PIXEL_RATE_4LANE 280800000
#define IMX219_DEFAULT_LINK_FREQ 456000000
+#define IMX219_DEFAULT_LINK_FREQ_4LANE 363000000
+
+#define IMX219_REG_CSI_LANE_MODE 0x0114
+#define IMX219_CSI_2_LANE_MODE 0x01
+#define IMX219_CSI_4_LANE_MODE 0x03
/* V_TIMING internal */
#define IMX219_REG_VTS 0x0160
@@ -299,6 +305,10 @@ static const s64 imx219_link_freq_menu[] = {
IMX219_DEFAULT_LINK_FREQ,
};
+static const s64 imx219_link_freq_4lane_menu[] = {
+ IMX219_DEFAULT_LINK_FREQ_4LANE,
+};
+
static const char * const imx219_test_pattern_menu[] = {
"Disabled",
"Color Bars",
@@ -474,6 +484,9 @@ struct imx219 {
/* Streaming on/off */
bool streaming;
+
+ /* Two or Four lanes */
+ u8 lanes;
};
static inline struct imx219 *to_imx219(struct v4l2_subdev *_sd)
@@ -936,6 +949,13 @@ static int imx219_get_selection(struct v4l2_subdev *sd,
return -EINVAL;
}
+static int imx219_configure_lanes(struct imx219 *imx219)
+{
+ return imx219_write_reg(imx219, IMX219_REG_CSI_LANE_MODE,
+ IMX219_REG_VALUE_08BIT, (imx219->lanes == 2) ?
+ IMX219_CSI_2_LANE_MODE : IMX219_CSI_4_LANE_MODE);
+};
+
static int imx219_start_streaming(struct imx219 *imx219)
{
struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
@@ -953,6 +973,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
goto err_rpm_put;
}
+ /* Configure two or four Lane mode */
+ ret = imx219_configure_lanes(imx219);
+ if (ret) {
+ dev_err(&client->dev, "%s failed to configure lanes\n", __func__);
+ goto err_rpm_put;
+ }
+
/* Apply default values of current mode */
reg_list = &imx219->mode->reg_list;
ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
@@ -1184,6 +1211,11 @@ static const struct v4l2_subdev_internal_ops imx219_internal_ops = {
.open = imx219_open,
};
+static unsigned long imx219_get_pixel_rate(struct imx219 *imx219)
+{
+ return (imx219->lanes == 2) ? IMX219_PIXEL_RATE : IMX219_PIXEL_RATE_4LANE;
+}
+
/* Initialize control handlers */
static int imx219_init_controls(struct imx219 *imx219)
{
@@ -1205,15 +1237,16 @@ static int imx219_init_controls(struct imx219 *imx219)
/* By default, PIXEL_RATE is read only */
imx219->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
V4L2_CID_PIXEL_RATE,
- IMX219_PIXEL_RATE,
- IMX219_PIXEL_RATE, 1,
- IMX219_PIXEL_RATE);
+ imx219_get_pixel_rate(imx219),
+ imx219_get_pixel_rate(imx219), 1,
+ imx219_get_pixel_rate(imx219));
imx219->link_freq =
v4l2_ctrl_new_int_menu(ctrl_hdlr, &imx219_ctrl_ops,
V4L2_CID_LINK_FREQ,
ARRAY_SIZE(imx219_link_freq_menu) - 1, 0,
- imx219_link_freq_menu);
+ (imx219->lanes == 2) ? imx219_link_freq_menu :
+ imx219_link_freq_4lane_menu);
if (imx219->link_freq)
imx219->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
@@ -1308,7 +1341,7 @@ static void imx219_free_controls(struct imx219 *imx219)
mutex_destroy(&imx219->mutex);
}
-static int imx219_check_hwcfg(struct device *dev)
+static int imx219_check_hwcfg(struct device *dev, struct imx219 *imx219)
{
struct fwnode_handle *endpoint;
struct v4l2_fwnode_endpoint ep_cfg = {
@@ -1328,10 +1361,12 @@ static int imx219_check_hwcfg(struct device *dev)
}
/* Check the number of MIPI CSI2 data lanes */
- if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) {
- dev_err(dev, "only 2 data lanes are currently supported\n");
+ if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2 &&
+ ep_cfg.bus.mipi_csi2.num_data_lanes != 4) {
+ dev_err(dev, "only 2 or 4 data lanes are currently supported\n");
goto error_out;
}
+ imx219->lanes = ep_cfg.bus.mipi_csi2.num_data_lanes;
/* Check the link frequency set in device tree */
if (!ep_cfg.nr_of_link_frequencies) {
@@ -1339,8 +1374,8 @@ static int imx219_check_hwcfg(struct device *dev)
goto error_out;
}
- if (ep_cfg.nr_of_link_frequencies != 1 ||
- ep_cfg.link_frequencies[0] != IMX219_DEFAULT_LINK_FREQ) {
+ if (ep_cfg.link_frequencies[0] != ((imx219->lanes == 2) ?
+ IMX219_DEFAULT_LINK_FREQ : IMX219_DEFAULT_LINK_FREQ_4LANE)) {
dev_err(dev, "Link frequency not supported: %lld\n",
ep_cfg.link_frequencies[0]);
goto error_out;
@@ -1368,7 +1403,7 @@ static int imx219_probe(struct i2c_client *client)
v4l2_i2c_subdev_init(&imx219->sd, client, &imx219_subdev_ops);
/* Check the hardware configuration in device tree */
- if (imx219_check_hwcfg(dev))
+ if (imx219_check_hwcfg(dev, imx219))
return -EINVAL;
/* Get system clock (xclk) */
--
2.34.1
On Sat, Jul 9, 2022 at 8:51 AM Adam Ford <[email protected]> wrote:
>
> There are four modes, and each mode has a table of registers.
> Some of the registers are common to all modes, so create new
> tables for these common registers to reduce duplicate code.
>
Dave,
I've tried to address your concerns in this V3 series which is down to
2 patches. Any chance you can review them? I've tested the 4-lane
mode on both an imx8mp (still images) and a Renesas RZ/G2M (streaming
video) and both can capture in 4-lane mode.
adam
> Signed-off-by: Adam Ford <[email protected]>
> ---
> V3: Change some of the comments to better reflect their description
> Add a few more entries to the imx219_common_regs table.
>
> diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
> index e10af3f74b38..faa5dab3c2ec 100644
> --- a/drivers/media/i2c/imx219.c
> +++ b/drivers/media/i2c/imx219.c
> @@ -145,23 +145,61 @@ struct imx219_mode {
> struct imx219_reg_list reg_list;
> };
>
> -/*
> - * Register sets lifted off the i2C interface from the Raspberry Pi firmware
> - * driver.
> - * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
> - */
> -static const struct imx219_reg mode_3280x2464_regs[] = {
> - {0x0100, 0x00},
> +static const struct imx219_reg imx219_common_regs[] = {
> + {0x0100, 0x00}, /* Mode Select */
> +
> + /* To Access Addresses 3000-5fff, send the following commands */
> {0x30eb, 0x0c},
> {0x30eb, 0x05},
> {0x300a, 0xff},
> {0x300b, 0xff},
> {0x30eb, 0x05},
> {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> +
> + /* PLL Clock Table */
> + {0x0301, 0x05}, /* VTPXCK_DIV */
> + {0x0303, 0x01}, /* VTSYSCK_DIV */
> + {0x0304, 0x03}, /* PREPLLCK_VT_DIV 0x03 = AUTO set */
> + {0x0305, 0x03}, /* PREPLLCK_OP_DIV 0x03 = AUTO set */
> + {0x0306, 0x00}, /* PLL_VT_MPY */
> + {0x0307, 0x39},
> + {0x030b, 0x01}, /* OP_SYS_CLK_DIV */
> + {0x030c, 0x00}, /* PLL_OP_MPY */
> + {0x030d, 0x72},
> +
> + /* Undocumented registers */
> + {0x455e, 0x00},
> + {0x471e, 0x4b},
> + {0x4767, 0x0f},
> + {0x4750, 0x14},
> + {0x4540, 0x00},
> + {0x47b4, 0x14},
> + {0x4713, 0x30},
> + {0x478b, 0x10},
> + {0x478f, 0x10},
> + {0x4793, 0x10},
> + {0x4797, 0x0e},
> + {0x479b, 0x0e},
> +
> + /* Frame Bank Register Group "A" */
> + {0x0162, 0x0d}, /* Line_Length_A */
> + {0x0163, 0x78},
> + {0x0170, 0x01}, /* X_ODD_INC_A */
> + {0x0171, 0x01}, /* Y_ODD_INC_A */
> +
> + /* Output setup registers */
> + {0x0114, 0x01}, /* CSI 2-Lane Mode */
> + {0x0128, 0x00}, /* DPHY Auto Mode */
> + {0x012a, 0x18}, /* EXCK_Freq */
> {0x012b, 0x00},
> +};
> +
> +/*
> + * Register sets lifted off the i2C interface from the Raspberry Pi firmware
> + * driver.
> + * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
> + */
> +static const struct imx219_reg mode_3280x2464_regs[] = {
> {0x0164, 0x00},
> {0x0165, 0x00},
> {0x0166, 0x0c},
> @@ -174,53 +212,15 @@ static const struct imx219_reg mode_3280x2464_regs[] = {
> {0x016d, 0xd0},
> {0x016e, 0x09},
> {0x016f, 0xa0},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x00},
> + {0x0174, 0x00}, /* No-Binning */
> {0x0175, 0x00},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x0c},
> {0x0625, 0xd0},
> {0x0626, 0x09},
> {0x0627, 0xa0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> };
>
> static const struct imx219_reg mode_1920_1080_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x05},
> - {0x30eb, 0x0c},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> {0x0164, 0x02},
> {0x0165, 0xa8},
> {0x0166, 0x0a},
> @@ -233,49 +233,15 @@ static const struct imx219_reg mode_1920_1080_regs[] = {
> {0x016d, 0x80},
> {0x016e, 0x04},
> {0x016f, 0x38},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x00},
> + {0x0174, 0x00}, /* No-Binning */
> {0x0175, 0x00},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x07},
> {0x0625, 0x80},
> {0x0626, 0x04},
> {0x0627, 0x38},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> };
>
> static const struct imx219_reg mode_1640_1232_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x0c},
> - {0x30eb, 0x05},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> {0x0164, 0x00},
> {0x0165, 0x00},
> {0x0166, 0x0c},
> @@ -288,53 +254,15 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
> {0x016d, 0x68},
> {0x016e, 0x04},
> {0x016f, 0xd0},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x01},
> + {0x0174, 0x01}, /* x2-Binning */
> {0x0175, 0x01},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x06},
> {0x0625, 0x68},
> {0x0626, 0x04},
> {0x0627, 0xd0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> };
>
> static const struct imx219_reg mode_640_480_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x05},
> - {0x30eb, 0x0c},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> {0x0164, 0x03},
> {0x0165, 0xe8},
> {0x0166, 0x08},
> @@ -347,35 +275,12 @@ static const struct imx219_reg mode_640_480_regs[] = {
> {0x016d, 0x80},
> {0x016e, 0x01},
> {0x016f, 0xe0},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x03},
> + {0x0174, 0x03}, /* x2-analog binning */
> {0x0175, 0x03},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x06},
> {0x0625, 0x68},
> {0x0626, 0x04},
> {0x0627, 0xd0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> };
>
> static const struct imx219_reg raw8_framefmt_regs[] = {
> @@ -1041,6 +946,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
> if (ret < 0)
> return ret;
>
> + /* Send all registers that are common to all modes */
> + ret = imx219_write_regs(imx219, imx219_common_regs, ARRAY_SIZE(imx219_common_regs));
> + if (ret) {
> + dev_err(&client->dev, "%s failed to send mfg header\n", __func__);
> + goto err_rpm_put;
> + }
> +
> /* Apply default values of current mode */
> reg_list = &imx219->mode->reg_list;
> ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
> --
> 2.34.1
>
Hi Adam
Sorry for the delay in reviewing.
On Sat, 9 Jul 2022 at 14:51, Adam Ford <[email protected]> wrote:
>
> The imx219 camera is capable of either two-lane or four-lane
> operation. When operating in four-lane, both the pixel rate and
> link frequency change. Regardless of the mode, however, both
> frequencies remain fixed.
>
> Helper functions are needed to read and set pixel and link frequencies
> which also reduces the number of fixed registers in the table of modes.
>
> Since the link frequency and number of lanes is extracted from the
> endpoint, move the endpoint handling into the probe function and
> out of the imx219_check_hwcfg. This simplifies the imx219_check_hwcfg
> just a bit.
This paragraph isn't relevant any more.
> Signed-off-by: Adam Ford <[email protected]>
> ---
> V3: Keep the helper function doing the link and lane parsing to
> keep th probe function small.
>
> diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
> index faa5dab3c2ec..bb4125e7e113 100644
> --- a/drivers/media/i2c/imx219.c
> +++ b/drivers/media/i2c/imx219.c
> @@ -42,10 +42,16 @@
> /* External clock frequency is 24.0M */
> #define IMX219_XCLK_FREQ 24000000
>
> -/* Pixel rate is fixed at 182.4M for all the modes */
> +/* Pixel rate is fixed for all the modes */
> #define IMX219_PIXEL_RATE 182400000
> +#define IMX219_PIXEL_RATE_4LANE 280800000
>
> #define IMX219_DEFAULT_LINK_FREQ 456000000
> +#define IMX219_DEFAULT_LINK_FREQ_4LANE 363000000
> +
> +#define IMX219_REG_CSI_LANE_MODE 0x0114
> +#define IMX219_CSI_2_LANE_MODE 0x01
> +#define IMX219_CSI_4_LANE_MODE 0x03
>
> /* V_TIMING internal */
> #define IMX219_REG_VTS 0x0160
> @@ -299,6 +305,10 @@ static const s64 imx219_link_freq_menu[] = {
> IMX219_DEFAULT_LINK_FREQ,
> };
>
> +static const s64 imx219_link_freq_4lane_menu[] = {
> + IMX219_DEFAULT_LINK_FREQ_4LANE,
> +};
> +
> static const char * const imx219_test_pattern_menu[] = {
> "Disabled",
> "Color Bars",
> @@ -474,6 +484,9 @@ struct imx219 {
>
> /* Streaming on/off */
> bool streaming;
> +
> + /* Two or Four lanes */
> + u8 lanes;
> };
>
> static inline struct imx219 *to_imx219(struct v4l2_subdev *_sd)
> @@ -936,6 +949,13 @@ static int imx219_get_selection(struct v4l2_subdev *sd,
> return -EINVAL;
> }
>
> +static int imx219_configure_lanes(struct imx219 *imx219)
> +{
> + return imx219_write_reg(imx219, IMX219_REG_CSI_LANE_MODE,
> + IMX219_REG_VALUE_08BIT, (imx219->lanes == 2) ?
> + IMX219_CSI_2_LANE_MODE : IMX219_CSI_4_LANE_MODE);
> +};
> +
> static int imx219_start_streaming(struct imx219 *imx219)
> {
> struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
> @@ -953,6 +973,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
> goto err_rpm_put;
> }
>
> + /* Configure two or four Lane mode */
> + ret = imx219_configure_lanes(imx219);
> + if (ret) {
> + dev_err(&client->dev, "%s failed to configure lanes\n", __func__);
> + goto err_rpm_put;
> + }
> +
> /* Apply default values of current mode */
> reg_list = &imx219->mode->reg_list;
> ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
> @@ -1184,6 +1211,11 @@ static const struct v4l2_subdev_internal_ops imx219_internal_ops = {
> .open = imx219_open,
> };
>
> +static unsigned long imx219_get_pixel_rate(struct imx219 *imx219)
> +{
> + return (imx219->lanes == 2) ? IMX219_PIXEL_RATE : IMX219_PIXEL_RATE_4LANE;
> +}
> +
> /* Initialize control handlers */
> static int imx219_init_controls(struct imx219 *imx219)
> {
> @@ -1205,15 +1237,16 @@ static int imx219_init_controls(struct imx219 *imx219)
> /* By default, PIXEL_RATE is read only */
> imx219->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
> V4L2_CID_PIXEL_RATE,
> - IMX219_PIXEL_RATE,
> - IMX219_PIXEL_RATE, 1,
> - IMX219_PIXEL_RATE);
> + imx219_get_pixel_rate(imx219),
> + imx219_get_pixel_rate(imx219), 1,
> + imx219_get_pixel_rate(imx219));
>
> imx219->link_freq =
> v4l2_ctrl_new_int_menu(ctrl_hdlr, &imx219_ctrl_ops,
> V4L2_CID_LINK_FREQ,
> ARRAY_SIZE(imx219_link_freq_menu) - 1, 0,
> - imx219_link_freq_menu);
> + (imx219->lanes == 2) ? imx219_link_freq_menu :
> + imx219_link_freq_4lane_menu);
> if (imx219->link_freq)
> imx219->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
>
> @@ -1308,7 +1341,7 @@ static void imx219_free_controls(struct imx219 *imx219)
> mutex_destroy(&imx219->mutex);
> }
>
> -static int imx219_check_hwcfg(struct device *dev)
> +static int imx219_check_hwcfg(struct device *dev, struct imx219 *imx219)
> {
> struct fwnode_handle *endpoint;
> struct v4l2_fwnode_endpoint ep_cfg = {
> @@ -1328,10 +1361,12 @@ static int imx219_check_hwcfg(struct device *dev)
> }
>
> /* Check the number of MIPI CSI2 data lanes */
> - if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) {
> - dev_err(dev, "only 2 data lanes are currently supported\n");
> + if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2 &&
> + ep_cfg.bus.mipi_csi2.num_data_lanes != 4) {
> + dev_err(dev, "only 2 or 4 data lanes are currently supported\n");
> goto error_out;
> }
> + imx219->lanes = ep_cfg.bus.mipi_csi2.num_data_lanes;
>
> /* Check the link frequency set in device tree */
> if (!ep_cfg.nr_of_link_frequencies) {
> @@ -1339,8 +1374,8 @@ static int imx219_check_hwcfg(struct device *dev)
> goto error_out;
> }
>
> - if (ep_cfg.nr_of_link_frequencies != 1 ||
> - ep_cfg.link_frequencies[0] != IMX219_DEFAULT_LINK_FREQ) {
> + if (ep_cfg.link_frequencies[0] != ((imx219->lanes == 2) ?
> + IMX219_DEFAULT_LINK_FREQ : IMX219_DEFAULT_LINK_FREQ_4LANE)) {
You've lost the check of ep_cfg.nr_of_link_frequencies != 1 in this update.
Otherwise it looks good to me.
Dave
> dev_err(dev, "Link frequency not supported: %lld\n",
> ep_cfg.link_frequencies[0]);
> goto error_out;
> @@ -1368,7 +1403,7 @@ static int imx219_probe(struct i2c_client *client)
> v4l2_i2c_subdev_init(&imx219->sd, client, &imx219_subdev_ops);
>
> /* Check the hardware configuration in device tree */
> - if (imx219_check_hwcfg(dev))
> + if (imx219_check_hwcfg(dev, imx219))
> return -EINVAL;
>
> /* Get system clock (xclk) */
> --
> 2.34.1
>
On Sat, 9 Jul 2022 at 14:51, Adam Ford <[email protected]> wrote:
>
> There are four modes, and each mode has a table of registers.
> Some of the registers are common to all modes, so create new
> tables for these common registers to reduce duplicate code.
>
> Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Dave Stevenson <[email protected]>
> ---
> V3: Change some of the comments to better reflect their description
> Add a few more entries to the imx219_common_regs table.
>
> diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
> index e10af3f74b38..faa5dab3c2ec 100644
> --- a/drivers/media/i2c/imx219.c
> +++ b/drivers/media/i2c/imx219.c
> @@ -145,23 +145,61 @@ struct imx219_mode {
> struct imx219_reg_list reg_list;
> };
>
> -/*
> - * Register sets lifted off the i2C interface from the Raspberry Pi firmware
> - * driver.
> - * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
> - */
> -static const struct imx219_reg mode_3280x2464_regs[] = {
> - {0x0100, 0x00},
> +static const struct imx219_reg imx219_common_regs[] = {
> + {0x0100, 0x00}, /* Mode Select */
> +
> + /* To Access Addresses 3000-5fff, send the following commands */
> {0x30eb, 0x0c},
> {0x30eb, 0x05},
> {0x300a, 0xff},
> {0x300b, 0xff},
> {0x30eb, 0x05},
> {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> +
> + /* PLL Clock Table */
> + {0x0301, 0x05}, /* VTPXCK_DIV */
> + {0x0303, 0x01}, /* VTSYSCK_DIV */
> + {0x0304, 0x03}, /* PREPLLCK_VT_DIV 0x03 = AUTO set */
> + {0x0305, 0x03}, /* PREPLLCK_OP_DIV 0x03 = AUTO set */
> + {0x0306, 0x00}, /* PLL_VT_MPY */
> + {0x0307, 0x39},
> + {0x030b, 0x01}, /* OP_SYS_CLK_DIV */
> + {0x030c, 0x00}, /* PLL_OP_MPY */
> + {0x030d, 0x72},
> +
> + /* Undocumented registers */
> + {0x455e, 0x00},
> + {0x471e, 0x4b},
> + {0x4767, 0x0f},
> + {0x4750, 0x14},
> + {0x4540, 0x00},
> + {0x47b4, 0x14},
> + {0x4713, 0x30},
> + {0x478b, 0x10},
> + {0x478f, 0x10},
> + {0x4793, 0x10},
> + {0x4797, 0x0e},
> + {0x479b, 0x0e},
> +
> + /* Frame Bank Register Group "A" */
> + {0x0162, 0x0d}, /* Line_Length_A */
> + {0x0163, 0x78},
> + {0x0170, 0x01}, /* X_ODD_INC_A */
> + {0x0171, 0x01}, /* Y_ODD_INC_A */
> +
> + /* Output setup registers */
> + {0x0114, 0x01}, /* CSI 2-Lane Mode */
> + {0x0128, 0x00}, /* DPHY Auto Mode */
> + {0x012a, 0x18}, /* EXCK_Freq */
> {0x012b, 0x00},
> +};
> +
> +/*
> + * Register sets lifted off the i2C interface from the Raspberry Pi firmware
> + * driver.
> + * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
> + */
> +static const struct imx219_reg mode_3280x2464_regs[] = {
> {0x0164, 0x00},
> {0x0165, 0x00},
> {0x0166, 0x0c},
> @@ -174,53 +212,15 @@ static const struct imx219_reg mode_3280x2464_regs[] = {
> {0x016d, 0xd0},
> {0x016e, 0x09},
> {0x016f, 0xa0},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x00},
> + {0x0174, 0x00}, /* No-Binning */
> {0x0175, 0x00},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x0c},
> {0x0625, 0xd0},
> {0x0626, 0x09},
> {0x0627, 0xa0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> };
>
> static const struct imx219_reg mode_1920_1080_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x05},
> - {0x30eb, 0x0c},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> {0x0164, 0x02},
> {0x0165, 0xa8},
> {0x0166, 0x0a},
> @@ -233,49 +233,15 @@ static const struct imx219_reg mode_1920_1080_regs[] = {
> {0x016d, 0x80},
> {0x016e, 0x04},
> {0x016f, 0x38},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x00},
> + {0x0174, 0x00}, /* No-Binning */
> {0x0175, 0x00},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x07},
> {0x0625, 0x80},
> {0x0626, 0x04},
> {0x0627, 0x38},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> };
>
> static const struct imx219_reg mode_1640_1232_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x0c},
> - {0x30eb, 0x05},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> {0x0164, 0x00},
> {0x0165, 0x00},
> {0x0166, 0x0c},
> @@ -288,53 +254,15 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
> {0x016d, 0x68},
> {0x016e, 0x04},
> {0x016f, 0xd0},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x01},
> + {0x0174, 0x01}, /* x2-Binning */
> {0x0175, 0x01},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x06},
> {0x0625, 0x68},
> {0x0626, 0x04},
> {0x0627, 0xd0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> };
>
> static const struct imx219_reg mode_640_480_regs[] = {
> - {0x0100, 0x00},
> - {0x30eb, 0x05},
> - {0x30eb, 0x0c},
> - {0x300a, 0xff},
> - {0x300b, 0xff},
> - {0x30eb, 0x05},
> - {0x30eb, 0x09},
> - {0x0114, 0x01},
> - {0x0128, 0x00},
> - {0x012a, 0x18},
> - {0x012b, 0x00},
> - {0x0162, 0x0d},
> - {0x0163, 0x78},
> {0x0164, 0x03},
> {0x0165, 0xe8},
> {0x0166, 0x08},
> @@ -347,35 +275,12 @@ static const struct imx219_reg mode_640_480_regs[] = {
> {0x016d, 0x80},
> {0x016e, 0x01},
> {0x016f, 0xe0},
> - {0x0170, 0x01},
> - {0x0171, 0x01},
> - {0x0174, 0x03},
> + {0x0174, 0x03}, /* x2-analog binning */
> {0x0175, 0x03},
> - {0x0301, 0x05},
> - {0x0303, 0x01},
> - {0x0304, 0x03},
> - {0x0305, 0x03},
> - {0x0306, 0x00},
> - {0x0307, 0x39},
> - {0x030b, 0x01},
> - {0x030c, 0x00},
> - {0x030d, 0x72},
> {0x0624, 0x06},
> {0x0625, 0x68},
> {0x0626, 0x04},
> {0x0627, 0xd0},
> - {0x455e, 0x00},
> - {0x471e, 0x4b},
> - {0x4767, 0x0f},
> - {0x4750, 0x14},
> - {0x4540, 0x00},
> - {0x47b4, 0x14},
> - {0x4713, 0x30},
> - {0x478b, 0x10},
> - {0x478f, 0x10},
> - {0x4793, 0x10},
> - {0x4797, 0x0e},
> - {0x479b, 0x0e},
> };
>
> static const struct imx219_reg raw8_framefmt_regs[] = {
> @@ -1041,6 +946,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
> if (ret < 0)
> return ret;
>
> + /* Send all registers that are common to all modes */
> + ret = imx219_write_regs(imx219, imx219_common_regs, ARRAY_SIZE(imx219_common_regs));
> + if (ret) {
> + dev_err(&client->dev, "%s failed to send mfg header\n", __func__);
> + goto err_rpm_put;
> + }
> +
> /* Apply default values of current mode */
> reg_list = &imx219->mode->reg_list;
> ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
> --
> 2.34.1
>
On Wed, Jul 27, 2022 at 9:30 AM Dave Stevenson
<[email protected]> wrote:
>
> Hi Adam
>
> Sorry for the delay in reviewing.
>
> On Sat, 9 Jul 2022 at 14:51, Adam Ford <[email protected]> wrote:
> >
> > The imx219 camera is capable of either two-lane or four-lane
> > operation. When operating in four-lane, both the pixel rate and
> > link frequency change. Regardless of the mode, however, both
> > frequencies remain fixed.
> >
> > Helper functions are needed to read and set pixel and link frequencies
> > which also reduces the number of fixed registers in the table of modes.
> >
> > Since the link frequency and number of lanes is extracted from the
> > endpoint, move the endpoint handling into the probe function and
> > out of the imx219_check_hwcfg. This simplifies the imx219_check_hwcfg
> > just a bit.
>
> This paragraph isn't relevant any more.
Oops. I forgot to review the commit message. I'll fix on V4.
>
> > Signed-off-by: Adam Ford <[email protected]>
> > ---
> > V3: Keep the helper function doing the link and lane parsing to
> > keep th probe function small.
> >
> > diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
> > index faa5dab3c2ec..bb4125e7e113 100644
> > --- a/drivers/media/i2c/imx219.c
> > +++ b/drivers/media/i2c/imx219.c
> > @@ -42,10 +42,16 @@
> > /* External clock frequency is 24.0M */
> > #define IMX219_XCLK_FREQ 24000000
> >
> > -/* Pixel rate is fixed at 182.4M for all the modes */
> > +/* Pixel rate is fixed for all the modes */
> > #define IMX219_PIXEL_RATE 182400000
> > +#define IMX219_PIXEL_RATE_4LANE 280800000
> >
> > #define IMX219_DEFAULT_LINK_FREQ 456000000
> > +#define IMX219_DEFAULT_LINK_FREQ_4LANE 363000000
> > +
> > +#define IMX219_REG_CSI_LANE_MODE 0x0114
> > +#define IMX219_CSI_2_LANE_MODE 0x01
> > +#define IMX219_CSI_4_LANE_MODE 0x03
> >
> > /* V_TIMING internal */
> > #define IMX219_REG_VTS 0x0160
> > @@ -299,6 +305,10 @@ static const s64 imx219_link_freq_menu[] = {
> > IMX219_DEFAULT_LINK_FREQ,
> > };
> >
> > +static const s64 imx219_link_freq_4lane_menu[] = {
> > + IMX219_DEFAULT_LINK_FREQ_4LANE,
> > +};
> > +
> > static const char * const imx219_test_pattern_menu[] = {
> > "Disabled",
> > "Color Bars",
> > @@ -474,6 +484,9 @@ struct imx219 {
> >
> > /* Streaming on/off */
> > bool streaming;
> > +
> > + /* Two or Four lanes */
> > + u8 lanes;
> > };
> >
> > static inline struct imx219 *to_imx219(struct v4l2_subdev *_sd)
> > @@ -936,6 +949,13 @@ static int imx219_get_selection(struct v4l2_subdev *sd,
> > return -EINVAL;
> > }
> >
> > +static int imx219_configure_lanes(struct imx219 *imx219)
> > +{
> > + return imx219_write_reg(imx219, IMX219_REG_CSI_LANE_MODE,
> > + IMX219_REG_VALUE_08BIT, (imx219->lanes == 2) ?
> > + IMX219_CSI_2_LANE_MODE : IMX219_CSI_4_LANE_MODE);
> > +};
> > +
> > static int imx219_start_streaming(struct imx219 *imx219)
> > {
> > struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
> > @@ -953,6 +973,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
> > goto err_rpm_put;
> > }
> >
> > + /* Configure two or four Lane mode */
> > + ret = imx219_configure_lanes(imx219);
> > + if (ret) {
> > + dev_err(&client->dev, "%s failed to configure lanes\n", __func__);
> > + goto err_rpm_put;
> > + }
> > +
> > /* Apply default values of current mode */
> > reg_list = &imx219->mode->reg_list;
> > ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
> > @@ -1184,6 +1211,11 @@ static const struct v4l2_subdev_internal_ops imx219_internal_ops = {
> > .open = imx219_open,
> > };
> >
> > +static unsigned long imx219_get_pixel_rate(struct imx219 *imx219)
> > +{
> > + return (imx219->lanes == 2) ? IMX219_PIXEL_RATE : IMX219_PIXEL_RATE_4LANE;
> > +}
> > +
> > /* Initialize control handlers */
> > static int imx219_init_controls(struct imx219 *imx219)
> > {
> > @@ -1205,15 +1237,16 @@ static int imx219_init_controls(struct imx219 *imx219)
> > /* By default, PIXEL_RATE is read only */
> > imx219->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
> > V4L2_CID_PIXEL_RATE,
> > - IMX219_PIXEL_RATE,
> > - IMX219_PIXEL_RATE, 1,
> > - IMX219_PIXEL_RATE);
> > + imx219_get_pixel_rate(imx219),
> > + imx219_get_pixel_rate(imx219), 1,
> > + imx219_get_pixel_rate(imx219));
> >
> > imx219->link_freq =
> > v4l2_ctrl_new_int_menu(ctrl_hdlr, &imx219_ctrl_ops,
> > V4L2_CID_LINK_FREQ,
> > ARRAY_SIZE(imx219_link_freq_menu) - 1, 0,
> > - imx219_link_freq_menu);
> > + (imx219->lanes == 2) ? imx219_link_freq_menu :
> > + imx219_link_freq_4lane_menu);
> > if (imx219->link_freq)
> > imx219->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> >
> > @@ -1308,7 +1341,7 @@ static void imx219_free_controls(struct imx219 *imx219)
> > mutex_destroy(&imx219->mutex);
> > }
> >
> > -static int imx219_check_hwcfg(struct device *dev)
> > +static int imx219_check_hwcfg(struct device *dev, struct imx219 *imx219)
> > {
> > struct fwnode_handle *endpoint;
> > struct v4l2_fwnode_endpoint ep_cfg = {
> > @@ -1328,10 +1361,12 @@ static int imx219_check_hwcfg(struct device *dev)
> > }
> >
> > /* Check the number of MIPI CSI2 data lanes */
> > - if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) {
> > - dev_err(dev, "only 2 data lanes are currently supported\n");
> > + if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2 &&
> > + ep_cfg.bus.mipi_csi2.num_data_lanes != 4) {
> > + dev_err(dev, "only 2 or 4 data lanes are currently supported\n");
> > goto error_out;
> > }
> > + imx219->lanes = ep_cfg.bus.mipi_csi2.num_data_lanes;
> >
> > /* Check the link frequency set in device tree */
> > if (!ep_cfg.nr_of_link_frequencies) {
> > @@ -1339,8 +1374,8 @@ static int imx219_check_hwcfg(struct device *dev)
> > goto error_out;
> > }
> >
> > - if (ep_cfg.nr_of_link_frequencies != 1 ||
> > - ep_cfg.link_frequencies[0] != IMX219_DEFAULT_LINK_FREQ) {
> > + if (ep_cfg.link_frequencies[0] != ((imx219->lanes == 2) ?
> > + IMX219_DEFAULT_LINK_FREQ : IMX219_DEFAULT_LINK_FREQ_4LANE)) {
>
> You've lost the check of ep_cfg.nr_of_link_frequencies != 1 in this update.
oops. I'll fix in V4.
>
> Otherwise it looks good to me.
>
Thanks for the review and feedback.
adam
> Dave
>
> > dev_err(dev, "Link frequency not supported: %lld\n",
> > ep_cfg.link_frequencies[0]);
> > goto error_out;
> > @@ -1368,7 +1403,7 @@ static int imx219_probe(struct i2c_client *client)
> > v4l2_i2c_subdev_init(&imx219->sd, client, &imx219_subdev_ops);
> >
> > /* Check the hardware configuration in device tree */
> > - if (imx219_check_hwcfg(dev))
> > + if (imx219_check_hwcfg(dev, imx219))
> > return -EINVAL;
> >
> > /* Get system clock (xclk) */
> > --
> > 2.34.1
> >