From: Frieder Schrempf <[email protected]>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <[email protected]>
Signed-off-by: Frieder Schrempf <[email protected]>
Reviewed-by: Heiko Thiery <[email protected]>
---
Changes in v3:
* rebase on v6.0-rc1
Changes in v2:
* none
---
arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts | 3 +++
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 2 --
2 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index 4e5828fa815b..7af3c476fd9a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -321,6 +321,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
@@ -333,6 +334,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
@@ -345,6 +347,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 30299c2a98ea..33179157f619 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -86,7 +86,6 @@ pca9450: pmic@25 {
pinctrl-0 = <&pinctrl_pmic>;
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
regulators {
reg_vdd_soc: BUCK1 {
@@ -229,7 +228,6 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
pinctrl_pmic: pmicgrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141
- MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x141
>;
};
--
2.37.1