From: Frieder Schrempf <[email protected]>
This set contains a few improvements for the imx8mm-kontron devicetrees
(patch 3-7) and support for a new SoM (patch 8, including baseboard) that
complies to the Open Standard Module (OSM) 1.0 hardware specification, size S
(https://sget.org/standards/osm).
It also includes binding changes in patch 1 and 2.
Changes in v4:
* fix hex values and unit addresses in SPI NOR partition nodes
* fix SoM dtsi includes
Changes in v3:
* drop patch for 2 which was applied separately
* rebase on v6.0-rc1
* rename compatibles and file names
Changes in v2:
* move binding changes to beginning of patchset
* Allow arbitrary regulator names in PCA9450 bindings
* Use voltage rail names from schematic for PMIC regulator-names
* Add SPI NOR partition layout to devicetree
* Remove unneeded header include
* Add tags
Frieder Schrempf (8):
dt-bindings: arm: fsl: Rename compatibles for Kontron i.MX8MM
SoM/board
dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board
arm64: dts: imx8mm-kontron: Adjust compatibles, file names and model
strings
arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card
IO voltage
arm64: dts: imx8mm-kontron: Remove low DDRC operating point
arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for
PMIC regulator-names
arm64: dts: imx8mm-kontron: Add SPI NOR partition layout
arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S
.../devicetree/bindings/arm/fsl.yaml | 13 +-
arch/arm64/boot/dts/freescale/Makefile | 3 +-
.../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 376 ++++++++++++++++++
...tron-n801x-s.dts => imx8mm-kontron-bl.dts} | 9 +-
.../dts/freescale/imx8mm-kontron-osm-s.dtsi | 330 +++++++++++++++
...-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} | 53 ++-
6 files changed, 758 insertions(+), 26 deletions(-)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts} (96%)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} (87%)
--
2.37.2
From: Frieder Schrempf <[email protected]>
This adds support for the Kontron Electronics SL i.MX8MM OSM-S SoM
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v4:
* SPI NOR partitions: fix hex values in reg to be lowercase
* SPI NOR partitions: fix unit addresses to match reg
* fix SoM dtsi include
Changes in v3:
* rename devicetrees, compatibles and SoM model
* rebase on v6.0-rc1
Changes in v2:
* add SPI NOR partitions
* use voltage rail names for PMIC regulator-name
* drop unused header include
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mm-kontron-bl-osm-s.dts | 376 ++++++++++++++++++
.../dts/freescale/imx8mm-kontron-osm-s.dtsi | 330 +++++++++++++++
3 files changed, 707 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index d014f7c4c888..542e1d661f30 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -56,6 +56,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl-osm-s.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
new file mode 100644
index 000000000000..8b16bd68576c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-kontron-osm-s.dtsi"
+
+/ {
+ model = "Kontron BL i.MX8MM OSM-S (N802X S)";
+ compatible = "kontron,imx8mm-bl-osm-s", "kontron,imx8mm-osm-s", "fsl,imx8mm";
+
+ aliases {
+ ethernet1 = &usbnet;
+ };
+
+ /* fixed crystal dedicated to mcp2542fd */
+ osc_can: clock-osc-can {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ clock-output-names = "osc-can";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_led>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led3 {
+ label = "led3";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm2 0 5000 0>;
+ };
+
+ reg_rst_eth2: regulator-rst-eth2 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_eth2>;
+ gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-name = "rst-usb-eth2";
+ };
+
+ reg_usb1_vbus: regulator-usb1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+ gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "usb1-vbus";
+ };
+
+ reg_vdd_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vdd-5v";
+ };
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp251xfd";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can>;
+ clocks = <&osc_can>;
+ interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>;
+ /*
+ * Limit the SPI clock to 15 MHz to prevent issues
+ * with corrupted data due to chip errata.
+ */
+ spi-max-frequency = <15000000>;
+ vdd-supply = <®_vdd_3v3>;
+ xceiver-supply = <®_vdd_5v>;
+ };
+};
+
+&ecspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ eeram@0 {
+ compatible = "microchip,48l640";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-connection-type = "rgmii-rxid";
+ phy-handle = <ðphy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@0 {
+ reg = <0>;
+ reset-assert-us = <1>;
+ reset-deassert-us = <15000>;
+ reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio1>;
+ gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
+ "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio5>;
+ gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ linux,rs485-enabled-at-boot-time;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ disable-over-current;
+ vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ usb1@1 {
+ compatible = "usb424,9514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbnet: ethernet@1 {
+ compatible = "usb424,ec00";
+ reg = <1>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ vmmc-supply = <®_vdd_3v3>;
+ vqmmc-supply = <®_nvcc_sd>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can: cangrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82
+ MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82
+ MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82
+ MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x82
+ MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x82
+ MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x82
+ MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x19
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x19 /* PHY RST */
+ MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* ETH IRQ */
+ >;
+ };
+
+ pinctrl_gpio_led: gpioledgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x19
+ MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x19
+ MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x19
+ >;
+ };
+
+ pinctrl_gpio1: gpio1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x19
+ MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19
+ MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19
+ MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19
+ >;
+ };
+
+ pinctrl_gpio5: gpio5grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x19
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x19
+ >;
+ };
+
+ pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x140
+ MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x140
+ MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B 0x140
+ MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B 0x140
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140
+ MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140
+ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140
+ >;
+ };
+
+ pinctrl_usb_eth2: usbeth2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
new file mode 100644
index 000000000000..8d10f5b41297
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx8mm.dtsi"
+
+/ {
+ model = "Kontron OSM-S i.MX8MM (N802X SOM)";
+ compatible = "kontron,imx8mm-osm-s", "fsl,imx8mm";
+
+ memory@40000000 {
+ device_type = "memory";
+ /*
+ * There are multiple SoM flavors with different DDR sizes.
+ * The smallest is 1GB. For larger sizes the bootloader will
+ * update the reg property.
+ */
+ reg = <0x0 0x40000000 0 0x80000000>;
+ };
+
+ chosen {
+ stdout-path = &uart3;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_1 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_2 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_3 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&ddrc {
+ operating-points-v2 = <&ddrc_opp_table>;
+
+ ddrc_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100M {
+ opp-hz = /bits/ 64 <100000000>;
+ };
+
+ opp-750M {
+ opp-hz = /bits/ 64 <750000000>;
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
+ spi-max-frequency = <80000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x1e0000>;
+ };
+
+ partition@1e0000 {
+ label = "env";
+ reg = <0x1e0000 0x10000>;
+ };
+
+ partition@1f0000 {
+ label = "env_redundant";
+ reg = <0x1f0000 0x10000>;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_vdd_soc: BUCK1 {
+ regulator-name = "+0V8_VDD_SOC (BUCK1)";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ nxp,dvs-run-voltage = <850000>;
+ nxp,dvs-standby-voltage = <800000>;
+ };
+
+ reg_vdd_arm: BUCK2 {
+ regulator-name = "+0V9_VDD_ARM (BUCK2)";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ };
+
+ reg_vdd_dram: BUCK3 {
+ regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_3v3: BUCK4 {
+ regulator-name = "+3V3 (BUCK4)";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_1v8: BUCK5 {
+ regulator-name = "+1V8 (BUCK5)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_dram: BUCK6 {
+ regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_snvs: LDO1 {
+ regulator-name = "+1V8_NVCC_SNVS (LDO1)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_snvs: LDO2 {
+ regulator-name = "+0V8_VDD_SNVS (LDO2)";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdda: LDO3 {
+ regulator-name = "+1V8_VDDA (LDO3)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vdd_phy: LDO4 {
+ regulator-name = "+0V9_VDD_PHY (LDO4)";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_nvcc_sd: LDO5 {
+ regulator-name = "NVCC_SD (LDO5)";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ rtc@52 {
+ compatible = "microcrystal,rv3028";
+ reg = <0x52>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>;
+ trickle-diode-disable;
+ };
+};
+
+&uart3 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ vmmc-supply = <®_vdd_3v3>;
+ vqmmc-supply = <®_vdd_1v8>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
+ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
+ MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x019
+ MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.37.2
From: Frieder Schrempf <[email protected]>
This is the layout used by the bootloader. Add it to the kernel
devicetree to make the same layout available in Linux and have
the devicetrees synced.
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v4:
* fix hex values in reg to be lowercase
* fix unit addresses to match reg
Changes in v3:
* rebase on v6.0-rc1
Changes in v2:
* new patch
---
.../boot/dts/freescale/imx8mm-kontron-sl.dtsi | 21 +++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index ce9c27619e26..0679728d2489 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -66,6 +66,27 @@ flash@0 {
compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
spi-max-frequency = <80000000>;
reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x1e0000>;
+ };
+
+ partition@1e0000 {
+ label = "env";
+ reg = <0x1e0000 0x10000>;
+ };
+
+ partition@1f0000 {
+ label = "env_redundant";
+ reg = <0x1f0000 0x10000>;
+ };
+ };
};
};
--
2.37.2
From: Frieder Schrempf <[email protected]>
Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <[email protected]>
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v4:
* none
Changes in v3:
* rebase on v6.0-rc1
Changes in v2:
* new patch
---
.../boot/dts/freescale/imx8mm-kontron-sl.dtsi | 22 +++++++++----------
1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 96ecdce67059..ce9c27619e26 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -85,7 +85,7 @@ pca9450: pmic@25 {
regulators {
reg_vdd_soc: BUCK1 {
- regulator-name = "buck1";
+ regulator-name = "+0V8_VDD_SOC (BUCK1)";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <850000>;
regulator-boot-on;
@@ -96,7 +96,7 @@ reg_vdd_soc: BUCK1 {
};
reg_vdd_arm: BUCK2 {
- regulator-name = "buck2";
+ regulator-name = "+0V9_VDD_ARM (BUCK2)";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <950000>;
regulator-boot-on;
@@ -107,7 +107,7 @@ reg_vdd_arm: BUCK2 {
};
reg_vdd_dram: BUCK3 {
- regulator-name = "buck3";
+ regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <950000>;
regulator-boot-on;
@@ -115,7 +115,7 @@ reg_vdd_dram: BUCK3 {
};
reg_vdd_3v3: BUCK4 {
- regulator-name = "buck4";
+ regulator-name = "+3V3 (BUCK4)";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
@@ -123,7 +123,7 @@ reg_vdd_3v3: BUCK4 {
};
reg_vdd_1v8: BUCK5 {
- regulator-name = "buck5";
+ regulator-name = "+1V8 (BUCK5)";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
@@ -131,7 +131,7 @@ reg_vdd_1v8: BUCK5 {
};
reg_nvcc_dram: BUCK6 {
- regulator-name = "buck6";
+ regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-boot-on;
@@ -139,7 +139,7 @@ reg_nvcc_dram: BUCK6 {
};
reg_nvcc_snvs: LDO1 {
- regulator-name = "ldo1";
+ regulator-name = "+1V8_NVCC_SNVS (LDO1)";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
@@ -147,7 +147,7 @@ reg_nvcc_snvs: LDO1 {
};
reg_vdd_snvs: LDO2 {
- regulator-name = "ldo2";
+ regulator-name = "+0V8_VDD_SNVS (LDO2)";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <900000>;
regulator-boot-on;
@@ -155,7 +155,7 @@ reg_vdd_snvs: LDO2 {
};
reg_vdda: LDO3 {
- regulator-name = "ldo3";
+ regulator-name = "+1V8_VDDA (LDO3)";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
@@ -163,7 +163,7 @@ reg_vdda: LDO3 {
};
reg_vdd_phy: LDO4 {
- regulator-name = "ldo4";
+ regulator-name = "+0V9_VDD_PHY (LDO4)";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-boot-on;
@@ -171,7 +171,7 @@ reg_vdd_phy: LDO4 {
};
reg_nvcc_sd: LDO5 {
- regulator-name = "ldo5";
+ regulator-name = "NVCC_SD (LDO5)";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
--
2.37.2
From: Frieder Schrempf <[email protected]>
The official naming includes "SL" (SoM-Line) or "BL" (Board-Line).
By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v4:
* fix SoM dtsi includes
Changes in v3:
* also rename compatibles and file names
* rebase on v6.0-rc1
Changes in v2:
* none
---
arch/arm64/boot/dts/freescale/Makefile | 2 +-
.../{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts} | 6 +++---
...imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} | 4 ++--
3 files changed, 6 insertions(+), 6 deletions(-)
rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-s.dts => imx8mm-kontron-bl.dts} (97%)
rename arch/arm64/boot/dts/freescale/{imx8mm-kontron-n801x-som.dtsi => imx8mm-kontron-sl.dtsi} (98%)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 8bf7f7ecebaa..d014f7c4c888 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -55,7 +55,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
-dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
similarity index 97%
rename from arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
rename to arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index 23be1ec538ba..ca533baedcd2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -5,11 +5,11 @@
/dts-v1/;
-#include "imx8mm-kontron-n801x-som.dtsi"
+#include "imx8mm-kontron-sl.dtsi"
/ {
- model = "Kontron i.MX8MM N801X S";
- compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+ model = "Kontron BL i.MX8MM (N801X S)";
+ compatible = "kontron,imx8mm-bl", "kontron,imx8mm-sl", "fsl,imx8mm";
aliases {
ethernet1 = &usbnet;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
similarity index 98%
rename from arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
rename to arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 8f90eb02550d..30299c2a98ea 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -6,8 +6,8 @@
#include "imx8mm.dtsi"
/ {
- model = "Kontron i.MX8MM N801X SoM";
- compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm";
+ model = "Kontron SL i.MX8MM (N801X SOM)";
+ compatible = "kontron,imx8mm-sl", "fsl,imx8mm";
memory@40000000 {
device_type = "memory";
--
2.37.2
From: Frieder Schrempf <[email protected]>
This updates the bindings in order to use names for the boards that
follow the latest convention used by Kontron marketing.
By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v4:
* none
Changes in v3:
* new patch
---
Documentation/devicetree/bindings/arm/fsl.yaml | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7431579ab0e8..4dcfa27044f0 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -831,7 +831,7 @@ properties:
- gw,imx8mm-gw7901 # i.MX8MM Gateworks Board
- gw,imx8mm-gw7902 # i.MX8MM Gateworks Board
- gw,imx8mm-gw7903 # i.MX8MM Gateworks Board
- - kontron,imx8mm-n801x-som # i.MX8MM Kontron SL (N801X) SOM
+ - kontron,imx8mm-sl # i.MX8MM Kontron SL (N801X) SOM
- menlo,mx8menlo # i.MX8MM Menlo board with Verdin SoM
- toradex,verdin-imx8mm # Verdin iMX8M Mini Modules
- toradex,verdin-imx8mm-nonwifi # Verdin iMX8M Mini Modules without Wi-Fi / BT
@@ -850,8 +850,8 @@ properties:
- description: Kontron BL i.MX8MM (N801X S) Board
items:
- - const: kontron,imx8mm-n801x-s
- - const: kontron,imx8mm-n801x-som
+ - const: kontron,imx8mm-bl
+ - const: kontron,imx8mm-sl
- const: fsl,imx8mm
- description: Toradex Boards with Verdin iMX8M Mini Modules
--
2.37.2
From: Frieder Schrempf <[email protected]>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <[email protected]>
Signed-off-by: Frieder Schrempf <[email protected]>
Reviewed-by: Heiko Thiery <[email protected]>
---
Changes in v4:
* none
Changes in v3:
* rebase on v6.0-rc1
Changes in v2:
* none
---
arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts | 3 +++
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 2 --
2 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
index ca533baedcd2..a079322a3793 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -321,6 +321,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
@@ -333,6 +334,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
@@ -345,6 +347,7 @@ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x019
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 30299c2a98ea..33179157f619 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -86,7 +86,6 @@ pca9450: pmic@25 {
pinctrl-0 = <&pinctrl_pmic>;
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
regulators {
reg_vdd_soc: BUCK1 {
@@ -229,7 +228,6 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
pinctrl_pmic: pmicgrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x141
- MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x141
>;
};
--
2.37.2
From: Frieder Schrempf <[email protected]>
For some reason there is a problem with finding a DDR configuration
that works on all operating points and all LPDDR4 types used on the
SoM. Therefore the bootloader currently doesn't configure the lowest
of the three operating points. Let's also skip this in the kernel
devicetree to make sure it isn't used.
Signed-off-by: Frieder Schrempf <[email protected]>
---
Changes in v4:
* none
Changes in v3:
* rebase on v6.0-rc1
Changes in v2:
* none
---
arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi | 4 ----
1 file changed, 4 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
index 33179157f619..96ecdce67059 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -46,10 +46,6 @@ &ddrc {
ddrc_opp_table: opp-table {
compatible = "operating-points-v2";
- opp-25M {
- opp-hz = /bits/ 64 <25000000>;
- };
-
opp-100M {
opp-hz = /bits/ 64 <100000000>;
};
--
2.37.2
From: Frieder Schrempf <[email protected]>
Add bindings for the Kontron BL i.MX8MM OSM-S board.
Signed-off-by: Frieder Schrempf <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
Changes in v4:
* none
Changes in v3:
* rename compatibles
* rebase on v6.0-rc1
Changes in v2:
* add A-b tag from Krzysztof (Thanks!)
---
Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 4dcfa27044f0..2b5a4d293e25 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -832,6 +832,7 @@ properties:
- gw,imx8mm-gw7902 # i.MX8MM Gateworks Board
- gw,imx8mm-gw7903 # i.MX8MM Gateworks Board
- kontron,imx8mm-sl # i.MX8MM Kontron SL (N801X) SOM
+ - kontron,imx8mm-osm-s # i.MX8MM Kontron OSM-S (N802X) SOM
- menlo,mx8menlo # i.MX8MM Menlo board with Verdin SoM
- toradex,verdin-imx8mm # Verdin iMX8M Mini Modules
- toradex,verdin-imx8mm-nonwifi # Verdin iMX8M Mini Modules without Wi-Fi / BT
@@ -854,6 +855,12 @@ properties:
- const: kontron,imx8mm-sl
- const: fsl,imx8mm
+ - description: Kontron BL i.MX8MM OSM-S (N802X S) Board
+ items:
+ - const: kontron,imx8mm-bl-osm-s
+ - const: kontron,imx8mm-osm-s
+ - const: fsl,imx8mm
+
- description: Toradex Boards with Verdin iMX8M Mini Modules
items:
- enum:
--
2.37.2
On 22/08/2022 11:03, Frieder Schrempf wrote:
> From: Frieder Schrempf <[email protected]>
>
> This updates the bindings in order to use names for the boards that
> follow the latest convention used by Kontron marketing.
>
> By updating we make sure, that we can maintain this more easily in
> future and make sure that the proper devicetree can be selected for
> the hardware.
>
> Signed-off-by: Frieder Schrempf <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On Mon, Aug 22, 2022 at 10:03:46AM +0200, Frieder Schrempf wrote:
> From: Frieder Schrempf <[email protected]>
>
> This set contains a few improvements for the imx8mm-kontron devicetrees
> (patch 3-7) and support for a new SoM (patch 8, including baseboard) that
> complies to the Open Standard Module (OSM) 1.0 hardware specification, size S
> (https://sget.org/standards/osm).
>
> It also includes binding changes in patch 1 and 2.
>
> Changes in v4:
> * fix hex values and unit addresses in SPI NOR partition nodes
> * fix SoM dtsi includes
>
> Changes in v3:
> * drop patch for 2 which was applied separately
> * rebase on v6.0-rc1
> * rename compatibles and file names
>
> Changes in v2:
> * move binding changes to beginning of patchset
> * Allow arbitrary regulator names in PCA9450 bindings
> * Use voltage rail names from schematic for PMIC regulator-names
> * Add SPI NOR partition layout to devicetree
> * Remove unneeded header include
> * Add tags
>
> Frieder Schrempf (8):
> dt-bindings: arm: fsl: Rename compatibles for Kontron i.MX8MM
> SoM/board
> dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board
> arm64: dts: imx8mm-kontron: Adjust compatibles, file names and model
> strings
> arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card
> IO voltage
> arm64: dts: imx8mm-kontron: Remove low DDRC operating point
> arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for
> PMIC regulator-names
> arm64: dts: imx8mm-kontron: Add SPI NOR partition layout
> arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S
Applied all, thanks!