In order to improve human readability, reduce the indentation by
returning early if the dp/edp cable is not plugged in.
Signed-off-by: Bo-Chen Chen <[email protected]>
---
drivers/gpu/drm/mediatek/mtk_dp.c | 66 ++++++++++++++++---------------
1 file changed, 34 insertions(+), 32 deletions(-)
diff --git a/drivers/gpu/drm/mediatek/mtk_dp.c b/drivers/gpu/drm/mediatek/mtk_dp.c
index dfa942ca62da..c72c646e25e9 100644
--- a/drivers/gpu/drm/mediatek/mtk_dp.c
+++ b/drivers/gpu/drm/mediatek/mtk_dp.c
@@ -1933,39 +1933,41 @@ static enum drm_connector_status mtk_dp_bdg_detect(struct drm_bridge *bridge)
bool enabled = mtk_dp->enabled;
u8 sink_count = 0;
- if (mtk_dp->train_info.cable_plugged_in) {
- if (!enabled) {
- /* power on aux */
- mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
- DP_PWR_STATE_BANDGAP_TPLL_LANE,
- DP_PWR_STATE_MASK);
-
- /* power on panel */
- drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D0);
- usleep_range(2000, 5000);
- }
- /*
- * Some dongles still source HPD when they do not connect to any
- * sink device. To avoid this, we need to read the sink count
- * to make sure we do connect to sink devices. After this detect
- * function, we just need to check the HPD connection to check
- * whether we connect to a sink device.
- */
- drm_dp_dpcd_readb(&mtk_dp->aux, DP_SINK_COUNT, &sink_count);
- if (DP_GET_SINK_COUNT(sink_count))
- ret = connector_status_connected;
-
- if (!enabled) {
- /* power off panel */
- drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
- usleep_range(2000, 3000);
-
- /* power off aux */
- mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
- DP_PWR_STATE_BANDGAP_TPLL,
- DP_PWR_STATE_MASK);
- }
+ if (!mtk_dp->train_info.cable_plugged_in)
+ return ret;
+
+ if (!enabled) {
+ /* power on aux */
+ mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
+ DP_PWR_STATE_BANDGAP_TPLL_LANE,
+ DP_PWR_STATE_MASK);
+
+ /* power on panel */
+ drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D0);
+ usleep_range(2000, 5000);
}
+ /*
+ * Some dongles still source HPD when they do not connect to any
+ * sink device. To avoid this, we need to read the sink count
+ * to make sure we do connect to sink devices. After this detect
+ * function, we just need to check the HPD connection to check
+ * whether we connect to a sink device.
+ */
+ drm_dp_dpcd_readb(&mtk_dp->aux, DP_SINK_COUNT, &sink_count);
+ if (DP_GET_SINK_COUNT(sink_count))
+ ret = connector_status_connected;
+
+ if (!enabled) {
+ /* power off panel */
+ drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
+ usleep_range(2000, 3000);
+
+ /* power off aux */
+ mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
+ DP_PWR_STATE_BANDGAP_TPLL,
+ DP_PWR_STATE_MASK);
+ }
+
return ret;
}
--
2.18.0
Bo-Chen Chen <[email protected]> 於 2022年9月16日 週五 晚上9:38寫道：
>
> In order to improve human readability, reduce the indentation by
> returning early if the dp/edp cable is not plugged in.
Acked-by: Chun-Kuang Hu <[email protected]>
>
> Signed-off-by: Bo-Chen Chen <[email protected]>
> ---
> drivers/gpu/drm/mediatek/mtk_dp.c | 66 ++++++++++++++++---------------
> 1 file changed, 34 insertions(+), 32 deletions(-)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_dp.c b/drivers/gpu/drm/mediatek/mtk_dp.c
> index dfa942ca62da..c72c646e25e9 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dp.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dp.c
> @@ -1933,39 +1933,41 @@ static enum drm_connector_status mtk_dp_bdg_detect(struct drm_bridge *bridge)
> bool enabled = mtk_dp->enabled;
> u8 sink_count = 0;
>
> - if (mtk_dp->train_info.cable_plugged_in) {
> - if (!enabled) {
> - /* power on aux */
> - mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
> - DP_PWR_STATE_BANDGAP_TPLL_LANE,
> - DP_PWR_STATE_MASK);
> -
> - /* power on panel */
> - drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D0);
> - usleep_range(2000, 5000);
> - }
> - /*
> - * Some dongles still source HPD when they do not connect to any
> - * sink device. To avoid this, we need to read the sink count
> - * to make sure we do connect to sink devices. After this detect
> - * function, we just need to check the HPD connection to check
> - * whether we connect to a sink device.
> - */
> - drm_dp_dpcd_readb(&mtk_dp->aux, DP_SINK_COUNT, &sink_count);
> - if (DP_GET_SINK_COUNT(sink_count))
> - ret = connector_status_connected;
> -
> - if (!enabled) {
> - /* power off panel */
> - drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
> - usleep_range(2000, 3000);
> -
> - /* power off aux */
> - mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
> - DP_PWR_STATE_BANDGAP_TPLL,
> - DP_PWR_STATE_MASK);
> - }
> + if (!mtk_dp->train_info.cable_plugged_in)
> + return ret;
> +
> + if (!enabled) {
> + /* power on aux */
> + mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
> + DP_PWR_STATE_BANDGAP_TPLL_LANE,
> + DP_PWR_STATE_MASK);
> +
> + /* power on panel */
> + drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D0);
> + usleep_range(2000, 5000);
> }
> + /*
> + * Some dongles still source HPD when they do not connect to any
> + * sink device. To avoid this, we need to read the sink count
> + * to make sure we do connect to sink devices. After this detect
> + * function, we just need to check the HPD connection to check
> + * whether we connect to a sink device.
> + */
> + drm_dp_dpcd_readb(&mtk_dp->aux, DP_SINK_COUNT, &sink_count);
> + if (DP_GET_SINK_COUNT(sink_count))
> + ret = connector_status_connected;
> +
> + if (!enabled) {
> + /* power off panel */
> + drm_dp_dpcd_writeb(&mtk_dp->aux, DP_SET_POWER, DP_SET_POWER_D3);
> + usleep_range(2000, 3000);
> +
> + /* power off aux */
> + mtk_dp_update_bits(mtk_dp, MTK_DP_TOP_PWR_STATE,
> + DP_PWR_STATE_BANDGAP_TPLL,
> + DP_PWR_STATE_MASK);
> + }
> +
> return ret;
> }
>
> --
> 2.18.0
>
Il 16/09/22 15:38, Bo-Chen Chen ha scritto:
> In order to improve human readability, reduce the indentation by
> returning early if the dp/edp cable is not plugged in.
>
> Signed-off-by: Bo-Chen Chen <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>