2022-09-16 15:42:58

by Tim Harvey

Subject: [PATCH v2] ARM: dts: imx6qdl-gw53xx: add CAN regulator

The GW53xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.

Signed-off-by: Tim Harvey <[email protected]>
---
v2:
- move compatible to start of child node
- fix typo in commit log
---
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 18 +++++++++++++++++-
1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index a0710d562766..6c0c109046d8 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -129,6 +129,16 @@ reg_3p3v: regulator-3p3v {
regulator-always-on;
};

+ reg_can1_stby: regulator-can1-stby {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_can1>;
+ regulator-name = "can1_stby";
+ gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
reg_usb_h1_vbus: regulator-usb-h1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb_h1_vbus";
@@ -170,6 +180,7 @@ &audmux {
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <&reg_can1_stby>;
status = "okay";
};

@@ -600,7 +611,6 @@ pinctrl_flexcan1: flexcan1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b1
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b1
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* CAN_STBY */
>;
};

@@ -691,6 +701,12 @@ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
>;
};

+ pinctrl_reg_can1: regcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x4001b0b0 /* CAN_STBY */
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
--
2.25.1

2022-09-17 05:04:54

by Shawn Guo

Subject: Re: [PATCH v2] ARM: dts: imx6qdl-gw53xx: add CAN regulator

On Fri, Sep 16, 2022 at 08:30:02AM -0700, Tim Harvey wrote:
> The GW53xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
> Configure this as a regulator to drive it low when CAN is in use.
>
> Signed-off-by: Tim Harvey <[email protected]>

Applied, thanks!