MPL115 supports shutdown gpio which can be used to set the default
state to low power mode. Power from all internal circuits and
registers is removed. This is done by pulling the SHDN pin to low.
This patch sets the default mode to low-power and only exits when
a reading is required from the chip. This maximises power savings.
According to spec., a wakeup time period of ~5 ms exists between
waking up and actually communicating with the device. This is
implemented using sleep delay.
Signed-off-by: Rajat Khandelwal <[email protected]>
---
drivers/iio/pressure/mpl115.c | 33 +++++++++++++++++++++++++++++----
1 file changed, 29 insertions(+), 4 deletions(-)
diff --git a/drivers/iio/pressure/mpl115.c b/drivers/iio/pressure/mpl115.c
index 5bf5b9abe6f1..c0ad3e941d05 100644
--- a/drivers/iio/pressure/mpl115.c
+++ b/drivers/iio/pressure/mpl115.c
@@ -3,13 +3,12 @@
* mpl115.c - Support for Freescale MPL115A pressure/temperature sensor
*
* Copyright (c) 2014 Peter Meerwald <[email protected]>
- *
- * TODO: shutdown pin
*/
#include <linux/module.h>
#include <linux/iio/iio.h>
#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
#include "mpl115.h"
@@ -27,6 +26,7 @@ struct mpl115_data {
s16 a0;
s16 b1, b2;
s16 c12;
+ struct gpio_desc *shutdown;
const struct mpl115_ops *ops;
};
@@ -102,13 +102,27 @@ static int mpl115_read_raw(struct iio_dev *indio_dev,
switch (mask) {
case IIO_CHAN_INFO_PROCESSED:
- ret = mpl115_comp_pressure(data, val, val2);
+ if (data->shutdown) {
+ gpiod_set_value(data->shutdown, 0);
+ usleep_range(5000, 6000);
+ ret = mpl115_comp_pressure(data, val, val2);
+ gpiod_set_value(data->shutdown, 1);
+ } else
+ ret = mpl115_comp_pressure(data, val, val2);
+
if (ret < 0)
return ret;
return IIO_VAL_INT_PLUS_MICRO;
case IIO_CHAN_INFO_RAW:
/* temperature -5.35 C / LSB, 472 LSB is 25 C */
- ret = mpl115_read_temp(data);
+ if (data->shutdown) {
+ gpiod_set_value(data->shutdown, 0);
+ usleep_range(5000, 6000);
+ ret = mpl115_read_temp(data);
+ gpiod_set_value(data->shutdown, 1);
+ } else
+ ret = mpl115_read_temp(data);
+
if (ret < 0)
return ret;
*val = ret >> 6;
@@ -185,6 +199,17 @@ int mpl115_probe(struct device *dev, const char *name,
return ret;
data->c12 = ret;
+ data->shutdown = devm_gpiod_get_optional(dev, "shutdown",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(data->shutdown))
+ return dev_err_probe(dev, PTR_ERR(data->shutdown),
+ "cannot get shutdown gpio\n");
+
+ if (data->shutdown)
+ dev_dbg(dev, "low-power mode enabled");
+ else
+ dev_dbg(dev, "low-power mode disabled");
+
return devm_iio_device_register(dev, indio_dev);
}
EXPORT_SYMBOL_NS_GPL(mpl115_probe, IIO_MPL115);
--
2.34.1
On Tue, 27 Sep 2022 23:08:38 +0530
Rajat Khandelwal <[email protected]> wrote:
> MPL115 supports shutdown gpio which can be used to set the default
> state to low power mode. Power from all internal circuits and
> registers is removed. This is done by pulling the SHDN pin to low.
> This patch sets the default mode to low-power and only exits when
> a reading is required from the chip. This maximises power savings.
>
> According to spec., a wakeup time period of ~5 ms exists between
> waking up and actually communicating with the device. This is
> implemented using sleep delay.
>
> Signed-off-by: Rajat Khandelwal <[email protected]>
Hi Rajat,
5ms is a significant delay to add to the read paths on this device
(I think the normal readout is < 3msec total).
As such, have you considered implementing this as runtime_pm using
autosleep? That way, if the user is doing a bunch of readings (perhaps
to compute a more accurate average value) they won't end up powering the
device up and down. However, if the reads are infrequent then the
power saving will be achieved at the cost of more latency on the first
read after a long gap.
Thanks,
Jonathan
> ---
> drivers/iio/pressure/mpl115.c | 33 +++++++++++++++++++++++++++++----
> 1 file changed, 29 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/iio/pressure/mpl115.c b/drivers/iio/pressure/mpl115.c
> index 5bf5b9abe6f1..c0ad3e941d05 100644
> --- a/drivers/iio/pressure/mpl115.c
> +++ b/drivers/iio/pressure/mpl115.c
> @@ -3,13 +3,12 @@
> * mpl115.c - Support for Freescale MPL115A pressure/temperature sensor
> *
> * Copyright (c) 2014 Peter Meerwald <[email protected]>
> - *
> - * TODO: shutdown pin
> */
>
> #include <linux/module.h>
> #include <linux/iio/iio.h>
> #include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
>
> #include "mpl115.h"
>
> @@ -27,6 +26,7 @@ struct mpl115_data {
> s16 a0;
> s16 b1, b2;
> s16 c12;
> + struct gpio_desc *shutdown;
> const struct mpl115_ops *ops;
> };
>
> @@ -102,13 +102,27 @@ static int mpl115_read_raw(struct iio_dev *indio_dev,
>
> switch (mask) {
> case IIO_CHAN_INFO_PROCESSED:
> - ret = mpl115_comp_pressure(data, val, val2);
> + if (data->shutdown) {
> + gpiod_set_value(data->shutdown, 0);
> + usleep_range(5000, 6000);
> + ret = mpl115_comp_pressure(data, val, val2);
> + gpiod_set_value(data->shutdown, 1);
> + } else
> + ret = mpl115_comp_pressure(data, val, val2);
> +
> if (ret < 0)
> return ret;
> return IIO_VAL_INT_PLUS_MICRO;
> case IIO_CHAN_INFO_RAW:
> /* temperature -5.35 C / LSB, 472 LSB is 25 C */
> - ret = mpl115_read_temp(data);
> + if (data->shutdown) {
> + gpiod_set_value(data->shutdown, 0);
> + usleep_range(5000, 6000);
> + ret = mpl115_read_temp(data);
> + gpiod_set_value(data->shutdown, 1);
> + } else
> + ret = mpl115_read_temp(data);
> +
> if (ret < 0)
> return ret;
> *val = ret >> 6;
> @@ -185,6 +199,17 @@ int mpl115_probe(struct device *dev, const char *name,
> return ret;
> data->c12 = ret;
>
> + data->shutdown = devm_gpiod_get_optional(dev, "shutdown",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(data->shutdown))
> + return dev_err_probe(dev, PTR_ERR(data->shutdown),
> + "cannot get shutdown gpio\n");
> +
> + if (data->shutdown)
> + dev_dbg(dev, "low-power mode enabled");
> + else
> + dev_dbg(dev, "low-power mode disabled");
> +
> return devm_iio_device_register(dev, indio_dev);
> }
> EXPORT_SYMBOL_NS_GPL(mpl115_probe, IIO_MPL115);