2022-09-28 07:43:56

by Marcel Ziswiler

Subject: [PATCH v2 2/5] arm: dts: colibri-imx6: move vbus-supply to module level device tree

From: Marcel Ziswiler <[email protected]>

Move USB VBUS supply from single carrier board to module level device
tree. This pin is as per Colibri module family standard.

Signed-off-by: Marcel Ziswiler <[email protected]>
---

(no changes since v1)

arch/arm/boot/dts/imx6dl-colibri-aster.dts | 1 -
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 1 -
arch/arm/boot/dts/imx6dl-colibri-iris.dts | 1 -
arch/arm/boot/dts/imx6qdl-colibri.dtsi | 9 +++++++--
4 files changed, 7 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-colibri-aster.dts b/arch/arm/boot/dts/imx6dl-colibri-aster.dts
index 74e8a6cd8bed..a28e083f29d5 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-aster.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-aster.dts
@@ -99,7 +99,6 @@ &uart3 {
};

&usbh1 {
- vbus-supply = <&reg_usb_host_vbus>;
status = "okay";
};

diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 7272edd85a49..a02981d4a3fc 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -111,7 +111,6 @@ &uart3 {
};

&usbh1 {
- vbus-supply = <&reg_usb_host_vbus>;
status = "okay";
};

diff --git a/arch/arm/boot/dts/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
index cf77d894f6d7..c5797ff35b71 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-iris.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
@@ -138,7 +138,6 @@ &uart3 {
};

&usbh1 {
- vbus-supply = <&reg_usb_host_vbus>;
status = "okay";
};

diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 3e98b5da0cc6..21c5049bda4e 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -112,7 +112,7 @@ reg_module_3v3_audio: regulator-module-3v3-audio {

reg_usb_host_vbus: regulator-usb-host-vbus {
compatible = "regulator-fixed";
- gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* SODIMM 129 / USBH_PEN */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
regulator-max-microvolt = <5000000>;
@@ -677,6 +677,11 @@ &uart3 {
status = "disabled";
};

+/* Colibri USBH */
+&usbh1 {
+ vbus-supply = <&reg_usb_host_vbus>;
+};
+
/* Colibri USBC */
&usbotg {
disable-over-current;
@@ -995,7 +1000,7 @@ MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1

pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
fsl,pins = <
- /* USBH_EN */
+ /* SODIMM 129 / USBH_PEN */
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x0f058
>;
};
--
2.36.1