2022-10-03 17:28:34

by Eric Chanudet

[permalink] [raw]
Subject: [PATCH] mailbox: qcom-ipcc: flag IRQ NO_THREAD

PREEMPT_RT forces qcom-ipcc's handler to be threaded with interrupts
enabled, which triggers a warning in __handle_irq_event_percpu():
irq 173 handler irq_default_primary_handler+0x0/0x10 enabled interrupts
WARNING: CPU: 0 PID: 77 at kernel/irq/handle.c:161 __handle_irq_event_percpu+0x4c4/0x4d0

Mark it IRQF_NO_THREAD to avoid running the handler in a threaded
context with threadirqs or PREEMPT_RT enabled.

Signed-off-by: Eric Chanudet <[email protected]>
---
drivers/mailbox/qcom-ipcc.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mailbox/qcom-ipcc.c b/drivers/mailbox/qcom-ipcc.c
index 31d58b7d55fe..7e27acf6c0cc 100644
--- a/drivers/mailbox/qcom-ipcc.c
+++ b/drivers/mailbox/qcom-ipcc.c
@@ -308,7 +308,8 @@ static int qcom_ipcc_probe(struct platform_device *pdev)
goto err_mbox;

ret = devm_request_irq(&pdev->dev, ipcc->irq, qcom_ipcc_irq_fn,
- IRQF_TRIGGER_HIGH | IRQF_NO_SUSPEND, name, ipcc);
+ IRQF_TRIGGER_HIGH | IRQF_NO_SUSPEND |
+ IRQF_NO_THREAD, name, ipcc);
if (ret < 0) {
dev_err(&pdev->dev, "Failed to register the irq: %d\n", ret);
goto err_req_irq;
--
2.37.3


Subject: Re: [PATCH] mailbox: qcom-ipcc: flag IRQ NO_THREAD

On 2022-10-03 13:08:49 [-0400], Eric Chanudet wrote:
> PREEMPT_RT forces qcom-ipcc's handler to be threaded with interrupts
> enabled, which triggers a warning in __handle_irq_event_percpu():
> irq 173 handler irq_default_primary_handler+0x0/0x10 enabled interrupts
> WARNING: CPU: 0 PID: 77 at kernel/irq/handle.c:161 __handle_irq_event_percpu+0x4c4/0x4d0
>
> Mark it IRQF_NO_THREAD to avoid running the handler in a threaded
> context with threadirqs or PREEMPT_RT enabled.

The important bit of information is that this is a IRQ-multiplexer and
such it must not be threaded. Otherwise its child-interrupts would be
invoked from the thread handler which is not desired.
This is noticed by PREEMPT_RT but also on a non-PREEMPT_RT kernel where
`threadirqs' has been used.

Side note: Using request_irq() has the side effect that this interrupt
pops-up in /proc/interrupts and the "child-interrupt", too. So you
account two interrupts while "one" on the HW side occurred.
Maybe irq_set_chained_handler_and_data() would be better use.
Either way, this addresses the problem,

Acked-by: Sebastian Andrzej Siewior <[email protected]>

> Signed-off-by: Eric Chanudet <[email protected]>

Sebastian

2022-10-06 19:38:04

by Eric Chanudet

[permalink] [raw]
Subject: Re: [PATCH] mailbox: qcom-ipcc: flag IRQ NO_THREAD

On Tue, Oct 04, 2022 at 11:41:50AM +0200, Sebastian Andrzej Siewior wrote:
> On 2022-10-03 13:08:49 [-0400], Eric Chanudet wrote:
> > PREEMPT_RT forces qcom-ipcc's handler to be threaded with interrupts
> > enabled, which triggers a warning in __handle_irq_event_percpu():
> > irq 173 handler irq_default_primary_handler+0x0/0x10 enabled interrupts
> > WARNING: CPU: 0 PID: 77 at kernel/irq/handle.c:161 __handle_irq_event_percpu+0x4c4/0x4d0
> >
> > Mark it IRQF_NO_THREAD to avoid running the handler in a threaded
> > context with threadirqs or PREEMPT_RT enabled.
>
> The important bit of information is that this is a IRQ-multiplexer and
> such it must not be threaded. Otherwise its child-interrupts would be
> invoked from the thread handler which is not desired.
> This is noticed by PREEMPT_RT but also on a non-PREEMPT_RT kernel where
> `threadirqs' has been used.

Thank you, I will send a v2 shortly updating the description with the
above.

> Side note: Using request_irq() has the side effect that this interrupt
> pops-up in /proc/interrupts and the "child-interrupt", too. So you
> account two interrupts while "one" on the HW side occurred.
> Maybe irq_set_chained_handler_and_data() would be better use.

I see.

> Either way, this addresses the problem,

--
Eric Chanudet