Changes since v3:
- remove qcom,msm-id and qcom,board-id (4/4)
Changes since v2:
- remove intc address and size cells (4/4)
- move apps_rsc label property down (4/4)
- move properties in intc (4/4)
- remove leading zeroes in iommus (4/4)
- change 0x0 to 0 in regs except cpu (4/4)
- change 0 to 0x0 in memory regs (4/4)
- convert hex to decimal in rmi4 #cells properties (4/4)
Changes since v1:
- remove i2c interconnects (4/4)
- change regulator phandle names (4/4)
- change regulators node names (4/4)
- remove clock-output-names from xo-board (4/4)
- remove vdd-supply from touchscreen (4/4)
- move clocks to device dts (4/4)
- reorder pmic nodes, root nodes, and phandle references in dts (4/4)
- move status properties to bottom of nodes (4/4)
- accumulate commit message tags (1-3/4)
Do not apply this series yet. It is only for review comments. It can be
applied once the "qcom,sdm670-smmu-500" compatible string gets added (or
now if you don't care about handling an unnecessary quirk).
This adds the device trees and bindings to support the Qualcomm
Snapdragon 670 and Google Pixel 3a. This patch series, specifically the
last patch, depends on:
[PATCH v4 0/3] SDM670 Global Clocks
https://lore.kernel.org/all/[email protected]/T/
[PATCH v2 0/2] RPMh Support for PM660 and PM660L
https://lore.kernel.org/all/[email protected]/T/
[PATCH v2 0/2] SDM670 RPMh Clocks
https://lore.kernel.org/all/[email protected]/T/
[PATCH v2 0/2] SDM670 USB 2.0 support
https://lore.kernel.org/all/[email protected]/T/
[PATCH 0/2] SDM670 SDHCI support
https://lore.kernel.org/all/[email protected]/T/
[PATCH v2 0/2] SDM670 Power Domains
https://lore.kernel.org/all/[email protected]/T/
[PATCH v10 0/3] SDM670 Pin Control Driver
https://lore.kernel.org/all/[email protected]/T/
[PATCH v6 0/4] SDM670 GPI DMA support
https://lore.kernel.org/all/[email protected]/T/
[RFC PATCH v2 0/11] iommu/arm-smmu-qcom: Rework Qualcomm SMMU bindings and implementation
https://lore.kernel.org/linux-arm-msm/[email protected]/T/
[PATCH v4 0/1] iommu: SMMU for SDM670
https://lore.kernel.org/linux-arm-msm/[email protected]/T/
Richard Acayan (4):
dt-bindings: arm: cpus: add qcom kryo 360 compatible
dt-bindings: arm: qcom: add sdm670 and pixel 3a compatible
dt-bindings: firmware: scm: add sdm670 compatible
arm64: dts: qcom: add sdm670 and pixel 3a device trees
.../devicetree/bindings/arm/cpus.yaml | 1 +
.../devicetree/bindings/arm/qcom.yaml | 6 +
.../bindings/firmware/qcom,scm.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sdm670-google-sargo.dts | 531 ++++++++
arch/arm64/boot/dts/qcom/sdm670.dtsi | 1160 +++++++++++++++++
6 files changed, 1700 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
create mode 100644 arch/arm64/boot/dts/qcom/sdm670.dtsi
P.S.: Thank you to all the maintainers and reviewers who went through
everything and made helpful comments!
--
2.38.1
The Qualcomm Snapdragon 670 has been out for a while. Add a device tree
for it and the Google Pixel 3a as the first device.
The Pixel 3a has the same bootloader issue as the Pixel 3 and will not work
on Android 10 bootloaders or later until it gets fixed for the Pixel 3.
SoC Initial Features:
- power management
- clocks
- pinctrl
- eMMC
- USB 2.0
- GENI I2C
- IOMMU
- RPMh
- interrupts
Device-Specific Initial Features:
- side buttons (keys)
- regulators
- touchscreen
Signed-off-by: Richard Acayan <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sdm670-google-sargo.dts | 531 ++++++++
arch/arm64/boot/dts/qcom/sdm670.dtsi | 1160 +++++++++++++++++
3 files changed, 1692 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
create mode 100644 arch/arm64/boot/dts/qcom/sdm670.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index b0558d3389e5..4eb5d8829efb 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -124,6 +124,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-voyager.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm632-fairphone-fp3.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm636-sony-xperia-ganges-mermaid.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm660-xiaomi-lavender.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sdm670-google-sargo.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
new file mode 100644
index 000000000000..cf2ae540db12
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
@@ -0,0 +1,531 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for Google Pixel 3a, adapted from google-blueline device tree,
+ * xiaomi-lavender device tree, and oneplus-common device tree.
+ *
+ * Copyright (c) 2022, Richard Acayan. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include "sdm670.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &adsp_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+
+/ {
+ model = "Google Pixel 3a";
+ compatible = "google,sargo", "qcom,sdm670";
+
+ aliases { };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer@9c000000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0x9c000000 0 (1080 * 2220 * 4)>;
+ width = <1080>;
+ height = <2220>;
+ stride = <(1080 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ clocks {
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32764>;
+ };
+
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <38400000>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vol_up_pin>;
+
+ key-vol-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ mpss_region: mpss@8b000000 {
+ reg = <0 0x8b000000 0 0x9800000>;
+ no-map;
+ };
+
+ venus_mem: venus@94800000 {
+ reg = <0 0x94800000 0 0x500000>;
+ no-map;
+ };
+
+ wlan_msa_mem: wlan-msa@94d00000 {
+ reg = <0 0x94d00000 0 0x100000>;
+ no-map;
+ };
+
+ cdsp_mem: cdsp@94e00000 {
+ reg = <0 0x94e00000 0 0x800000>;
+ no-map;
+ };
+
+ mba_region: mba@95600000 {
+ reg = <0 0x95600000 0 0x200000>;
+ no-map;
+ };
+
+ adsp_mem: adsp@95800000 {
+ reg = <0 0x95800000 0 0x2200000>;
+ no-map;
+ };
+
+ ipa_fw_mem: ipa-fw@97a00000 {
+ reg = <0 0x97a00000 0 0x10000>;
+ no-map;
+ };
+
+ ipa_gsi_mem: ipa-gsi@97a10000 {
+ reg = <0 0x97a10000 0 0x5000>;
+ no-map;
+ };
+
+ gpu_mem: gpu@97a15000 {
+ reg = <0 0x97a15000 0 0x2000>;
+ no-map;
+ };
+
+ framebuffer-region@9c000000 {
+ reg = <0 0x9c000000 0 0x2400000>;
+ no-map;
+ };
+
+ /* Also includes ramoops regions */
+ debug_info_mem: debug-info@a1800000 {
+ reg = <0 0xa1800000 0 0x411000>;
+ no-map;
+ };
+ };
+
+ /*
+ * The touchscreen regulator seems to be controlled somehow by a gpio.
+ * Model it as a fixed regulator and keep it on. Without schematics we
+ * don't know how this is actually wired up...
+ */
+ ts_1p8_supply: ts-1p8-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "ts_1p8_supply";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pm660_gpios 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3312000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /*
+ * Supply map from xiaomi-lavender specifies this as the supply for
+ * ldob1, ldob9, ldob10, ldoa2, and ldoa3, while downstream specifies
+ * this as a power domain. Set this as a fixed regulator with the same
+ * voltage as lavender until display is needed to avoid unneccessarily
+ * using a deprecated binding (regulator-fixed-domain).
+ */
+ vreg_s2b_1p05: vreg-s2b-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s2b";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm660-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+
+ vdd-l1-l6-l7-supply = <&vreg_s6a_0p87>;
+ vdd-l2-l3-supply = <&vreg_s2b_1p05>;
+ vdd-l5-supply = <&vreg_s2b_1p05>;
+ vdd-l8-l9-l10-l11-l12-l13-l14-supply = <&vreg_s4a_2p04>;
+ vdd-l15-l16-l17-l18-l19-supply = <&vreg_bob>;
+
+ /*
+ * S1A (FTAPC0), S2A (FTAPC1), S3A (HFAPC1) are managed
+ * by the Core Power Reduction hardened (CPRh) and the
+ * Operating State Manager (OSM) HW automatically.
+ */
+
+ vreg_s4a_2p04: smps4 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-enable-ramp-delay = <200>;
+ };
+
+ vreg_s6a_0p87: smps6 {
+ regulator-min-microvolt = <1224000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-enable-ramp-delay = <150>;
+ };
+
+ /* LDOs */
+ vreg_l1a_1p225: ldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l2a_1p0: ldo2 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l3a_1p0: ldo3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l5a_0p848: ldo5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l6a_1p3: ldo6 {
+ regulator-min-microvolt = <1248000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l7a_1p2: ldo7 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l8a_1p8: ldo8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l9a_1p8: ldo9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l10a_1p8: ldo10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l11a_1p8: ldo11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l13a_1p8: ldo13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l15a_1p8: ldo15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l16a_2p7: ldo16 {
+ regulator-min-microvolt = <2696000>;
+ regulator-max-microvolt = <2696000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l17a_1p8: ldo17 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l19a_3p3: ldo19 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm660l-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+
+ vdd-l1-l9-l10-supply = <&vreg_s2b_1p05>;
+ vdd-l2-supply = <&vreg_bob>;
+ vdd-l3-l5-l7-l8-supply = <&vreg_bob>;
+ vdd-l4-l6-supply = <&vreg_bob>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ /* LDOs */
+ vreg_l1b_0p925: ldo1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <900000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l2b_2p95: ldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l3b_3p0: ldo3 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l4b_2p95: ldo4 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l5b_2p95: ldo5 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l6b_3p3: ldo6 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l7b_3p125: ldo7 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3100000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ vreg_l8b_3p3: ldo8 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-enable-ramp-delay = <250>;
+ };
+
+ /*
+ * Downstream specifies a fixed voltage of 3.312 V, but the
+ * PMIC4 BOB ranges don't support that. Widen the range a
+ * little to avoid adding a new BOB regulator type.
+ */
+ vreg_bob: bob {
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3328000>;
+ regulator-enable-ramp-delay = <500>;
+ };
+ };
+
+};
+
+&gcc {
+ protected-clocks = <GCC_QSPI_CORE_CLK>,
+ <GCC_QSPI_CORE_CLK_SRC>,
+ <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c9 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ synaptics-rmi4-i2c@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_default>;
+
+ vio-supply = <&ts_1p8_supply>;
+
+ syna,reset-delay-ms = <200>;
+ syna,startup-delay-ms = <200>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x01>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ touchscreen-x-mm = <62>;
+ touchscreen-y-mm = <127>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&pm660l_gpios {
+ vol_up_pin: vol-up-state {
+ pins = "gpio7";
+ function = "normal";
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ input-enable;
+ bias-pull-up;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&sdhc_1 {
+ supports-cqe;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-ddr-1_8v;
+
+ qcom,ddr-config = <0xc3040873>;
+
+ vmmc-supply = <&vreg_l4b_2p95>;
+ vqmmc-supply = <&vreg_l8a_1p8>;
+
+ status = "okay";
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ touchscreen_default: ts-default-state {
+ ts-reset-pins {
+ pins = "gpio99";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ output-high;
+ };
+
+ ts-irq-pins {
+ pins = "gpio125";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ ts-switch-pins {
+ pins = "gpio135";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+ };
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l1b_0p925>;
+ vdda-pll-supply = <&vreg_l10a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ qcom,select-utmi-as-pipe-clk;
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ /* Only peripheral works for now */
+ dr_mode = "peripheral";
+
+ /* Do not assume that sdm670.dtsi will never support USB 3.0 */
+ phys = <&usb_1_hsphy>;
+ phy-names = "usb2-phy";
+ maximum-speed = "high-speed";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi
new file mode 100644
index 000000000000..47363fde64ac
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi
@@ -0,0 +1,1160 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM670 SoC device tree source, adapted from SDM845 SoC device tree
+ *
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Richard Acayan. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdm845.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases { };
+
+ chosen { };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD0>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ L3_0: l3-cache {
+ compatible = "cache";
+ };
+ };
+ };
+
+ CPU1: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD1>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_100>;
+ L2_100: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU2: cpu@200 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x200>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD2>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_200>;
+ L2_200: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU3: cpu@300 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x300>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD3>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_300>;
+ L2_300: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU4: cpu@400 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x400>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD4>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_400>;
+ L2_400: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU5: cpu@500 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x500>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD5>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_500>;
+ L2_500: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU6: cpu@600 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x600>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD6>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_600>;
+ L2_600: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ CPU7: cpu@700 {
+ device_type = "cpu";
+ compatible = "qcom,kryo360";
+ reg = <0x0 0x700>;
+ enable-method = "psci";
+ power-domains = <&CPU_PD7>;
+ power-domain-names = "psci";
+ next-level-cache = <&L2_700>;
+ L2_700: l2-cache {
+ compatible = "cache";
+ next-level-cache = <&L3_0>;
+ };
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+
+ core2 {
+ cpu = <&CPU2>;
+ };
+
+ core3 {
+ cpu = <&CPU3>;
+ };
+
+ core4 {
+ cpu = <&CPU4>;
+ };
+
+ core5 {
+ cpu = <&CPU5>;
+ };
+
+ core6 {
+ cpu = <&CPU6>;
+ };
+
+ core7 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+
+ idle-states {
+ entry-method = "psci";
+
+ LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+ compatible = "arm,idle-state";
+ idle-state-name = "little-rail-power-collapse";
+ arm,psci-suspend-param = <0x40000004>;
+ entry-latency-us = <702>;
+ exit-latency-us = <915>;
+ min-residency-us = <1617>;
+ local-timer-stop;
+ };
+
+ BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+ compatible = "arm,idle-state";
+ idle-state-name = "big-rail-power-collapse";
+ arm,psci-suspend-param = <0x40000004>;
+ entry-latency-us = <526>;
+ exit-latency-us = <1854>;
+ min-residency-us = <2380>;
+ local-timer-stop;
+ };
+ };
+
+ domain-idle-states {
+ CLUSTER_SLEEP_0: cluster-sleep-0 {
+ compatible = "domain-idle-state";
+ arm,psci-suspend-param = <0x4100c244>;
+ entry-latency-us = <3263>;
+ exit-latency-us = <6562>;
+ min-residency-us = <9825>;
+ };
+ };
+ };
+
+ firmware {
+ scm {
+ compatible = "qcom,scm-sdm670", "qcom,scm";
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+
+ CPU_PD0: power-domain-cpu0 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD1: power-domain-cpu1 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD2: power-domain-cpu2 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD3: power-domain-cpu3 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD4: power-domain-cpu4 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD5: power-domain-cpu5 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+ };
+
+ CPU_PD6: power-domain-cpu6 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&BIG_CPU_SLEEP_0>;
+ };
+
+ CPU_PD7: power-domain-cpu7 {
+ #power-domain-cells = <0>;
+ power-domains = <&CLUSTER_PD>;
+ domain-idle-states = <&BIG_CPU_SLEEP_0>;
+ };
+
+ CLUSTER_PD: power-domain-cluster {
+ #power-domain-cells = <0>;
+ domain-idle-states = <&CLUSTER_SLEEP_0>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hyp_mem: hyp-mem@85700000 {
+ reg = <0 0x85700000 0 0x600000>;
+ no-map;
+ };
+
+ xbl_mem: xbl-mem@85e00000 {
+ reg = <0 0x85e00000 0 0x100000>;
+ no-map;
+ };
+
+ aop_mem: aop-mem@85fc0000 {
+ reg = <0 0x85fc0000 0 0x20000>;
+ no-map;
+ };
+
+ aop_cmd_db_mem: aop-cmd-db-mem@85fe0000 {
+ compatible = "qcom,cmd-db";
+ reg = <0 0x85fe0000 0 0x20000>;
+ no-map;
+ };
+
+ camera_mem: camera-mem@8ab00000 {
+ reg = <0 0x8ab00000 0 0x500000>;
+ no-map;
+ };
+
+ mpss_region: mpss@8b000000 {
+ reg = <0 0x8b000000 0 0x7e00000>;
+ no-map;
+ };
+
+ venus_mem: venus@92e00000 {
+ reg = <0 0x92e00000 0 0x500000>;
+ no-map;
+ };
+
+ wlan_msa_mem: wlan-msa@93300000 {
+ reg = <0 0x93300000 0 0x100000>;
+ no-map;
+ };
+
+ cdsp_mem: cdsp@93400000 {
+ reg = <0 0x93400000 0 0x800000>;
+ no-map;
+ };
+
+ mba_region: mba@93c00000 {
+ reg = <0 0x93c00000 0 0x200000>;
+ no-map;
+ };
+
+ adsp_mem: adsp@93e00000 {
+ reg = <0 0x93e00000 0 0x1e00000>;
+ no-map;
+ };
+
+ ipa_fw_mem: ipa-fw@95c00000 {
+ reg = <0 0x95c00000 0 0x10000>;
+ no-map;
+ };
+
+ ipa_gsi_mem: ipa-gsi@95c10000 {
+ reg = <0 0x95c10000 0 0x5000>;
+ no-map;
+ };
+
+ gpu_mem: gpu@95c15000 {
+ reg = <0 0x95c15000 0 0x2000>;
+ no-map;
+ };
+
+ spss_mem: spss@97b00000 {
+ reg = <0 0x97b00000 0 0x100000>;
+ no-map;
+ };
+
+ qseecom_mem: qseecom@9e400000 {
+ reg = <0 0x9e400000 0 0x1400000>;
+ no-map;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ soc: soc@0 {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@100000 {
+ compatible = "qcom,gcc-sdm670";
+ reg = <0 0x00100000 0 0x1f0000>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&rpmhcc RPMH_CXO_CLK_A>,
+ <&sleep_clk>;
+ clock-names = "bi_tcxo",
+ "bi_tcxo_ao",
+ "sleep_clk";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ sdhc_1: mmc@7c4000 {
+ compatible = "qcom,sdm670-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x007c4000 0 0x1000>,
+ <0 0x007c5000 0 0x1000>,
+ <0 0x007c8000 0 0x8000>;
+ reg-names = "hc", "cqhci", "ice";
+
+ interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_SDCC1_ICE_CORE_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>;
+ clock-names = "iface", "core", "xo", "ice", "bus";
+
+ iommus = <&apps_smmu 0x140 0xf>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_state_on>;
+ pinctrl-1 = <&sdc1_state_off>;
+ power-domains = <&rpmhpd SDM670_CX>;
+
+ bus-width = <8>;
+ non-removable;
+
+ status = "disabled";
+ };
+
+ gpi_dma0: dma-controller@800000 {
+ #dma-cells = <3>;
+ compatible = "qcom,sdm670-gpi-dma", "qcom,sdm845-gpi-dma";
+ reg = <0 0x00800000 0 0x60000>;
+ interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <13>;
+ dma-channel-mask = <0xfa>;
+ iommus = <&apps_smmu 0x16 0x0>;
+ status = "disabled";
+ };
+
+ qupv3_id_0: geniqup@8c0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x008c0000 0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ iommus = <&apps_smmu 0x3 0x0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ i2c0: i2c@880000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00880000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c0_default>;
+ interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c1: i2c@884000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00884000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c1_default>;
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c2: i2c@888000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00888000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c2_default>;
+ interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c3: i2c@88c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c3_default>;
+ interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c4: i2c@890000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00890000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c4_default>;
+ interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c5: i2c@894000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00894000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c5_default>;
+ interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c6: i2c@898000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00898000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c6_default>;
+ interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c7: i2c@89c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x0089c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c7_default>;
+ interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 7 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+ };
+
+ gpi_dma1: dma-controller@a00000 {
+ #dma-cells = <3>;
+ compatible = "qcom,sdm670-gpi-dma", "qcom,sdm845-gpi-dma";
+ reg = <0 0x00a00000 0 0x60000>;
+ interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ dma-channels = <13>;
+ dma-channel-mask = <0xfa>;
+ iommus = <&apps_smmu 0x6d6 0x0>;
+ status = "disabled";
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x00ac0000 0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ iommus = <&apps_smmu 0x6c3 0x0>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_default>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_default>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_default>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_default>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_default>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_default>;
+ interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c15_default>;
+ interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SDM670_CX>;
+ dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+ };
+
+ tlmm: pinctrl@3400000 {
+ compatible = "qcom,sdm670-tlmm";
+ reg = <0 0x03400000 0 0xc00000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 151>;
+
+ qup_i2c0_default: qup-i2c0-default-state {
+ pins = "gpio0", "gpio1";
+ function = "qup0";
+ };
+
+ qup_i2c1_default: qup-i2c1-default-state {
+ pins = "gpio17", "gpio18";
+ function = "qup1";
+ };
+
+ qup_i2c2_default: qup-i2c2-default-state {
+ pins = "gpio27", "gpio28";
+ function = "qup2";
+ };
+
+ qup_i2c3_default: qup-i2c3-default-state {
+ pins = "gpio41", "gpio42";
+ function = "qup3";
+ };
+
+ qup_i2c4_default: qup-i2c4-default-state {
+ pins = "gpio89", "gpio90";
+ function = "qup4";
+ };
+
+ qup_i2c5_default: qup-i2c5-default-state {
+ pins = "gpio85", "gpio86";
+ function = "qup5";
+ };
+
+ qup_i2c6_default: qup-i2c6-default-state {
+ pins = "gpio45", "gpio46";
+ function = "qup6";
+ };
+
+ qup_i2c7_default: qup-i2c7-default-state {
+ pins = "gpio93", "gpio94";
+ function = "qup7";
+ };
+
+ qup_i2c8_default: qup-i2c8-default-state {
+ pins = "gpio65", "gpio66";
+ function = "qup8";
+ };
+
+ qup_i2c9_default: qup-i2c9-default-state {
+ pins = "gpio6", "gpio7";
+ function = "qup9";
+ };
+
+ qup_i2c10_default: qup-i2c10-default-state {
+ pins = "gpio55", "gpio56";
+ function = "qup10";
+ };
+
+ qup_i2c11_default: qup-i2c11-default-state {
+ pins = "gpio31", "gpio32";
+ function = "qup11";
+ };
+
+ qup_i2c12_default: qup-i2c12-default-state {
+ pins = "gpio49", "gpio50";
+ function = "qup12";
+ };
+
+ qup_i2c13_default: qup-i2c13-default-state {
+ pins = "gpio105", "gpio106";
+ function = "qup13";
+ };
+
+ qup_i2c14_default: qup-i2c14-default-state {
+ pins = "gpio33", "gpio34";
+ function = "qup14";
+ };
+
+ qup_i2c15_default: qup-i2c15-default-state {
+ pins = "gpio81", "gpio82";
+ function = "qup15";
+ };
+
+ sdc1_state_on: sdc1-on-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc1_state_off: sdc1-off-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+ };
+
+ usb_1_hsphy: phy@88e2000 {
+ compatible = "qcom,sdm670-qusb2-phy", "qcom,qusb2-v2-phy";
+ reg = <0 0x088e2000 0 0x400>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+ status = "disabled";
+ };
+
+ usb_1: usb@a6f8800 {
+ compatible = "qcom,sdm670-dwc3", "qcom,dwc3";
+ reg = <0 0x0a6f8800 0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+ clock-names = "cfg_noc",
+ "core",
+ "iface",
+ "sleep",
+ "mock_utmi";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ status = "disabled";
+
+ usb_1_dwc3: usb@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a600000 0 0xcd00>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x740 0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_1_hsphy>;
+ phy-names = "usb2-phy";
+ };
+ };
+
+ spmi_bus: spmi@c440000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0 0x0c440000 0 0x1100>,
+ <0 0x0c600000 0 0x2000000>,
+ <0 0x0e600000 0 0x100000>,
+ <0 0x0e700000 0 0xa0000>,
+ <0 0x0c40a000 0 0x26000>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ apps_smmu: iommu@15000000 {
+ compatible = "qcom,sdm670-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+ reg = <0 0x15000000 0 0x80000>;
+ #iommu-cells = <2>;
+ #global-interrupts = <1>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apps_rsc: rsc@179c0000 {
+ compatible = "qcom,rpmh-rsc";
+ reg = <0 0x179c0000 0 0x10000>,
+ <0 0x179d0000 0 0x10000>,
+ <0 0x179e0000 0 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ label = "apps_rsc";
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>,
+ <SLEEP_TCS 3>,
+ <WAKE_TCS 3>,
+ <CONTROL_TCS 1>;
+
+ apps_bcm_voter: bcm-voter {
+ compatible = "qcom,bcm-voter";
+ };
+
+ rpmhcc: clock-controller {
+ compatible = "qcom,sdm670-rpmh-clk";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
+
+ rpmhpd: power-controller {
+ compatible = "qcom,sdm670-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmhpd_opp_ret: opp1 {
+ opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
+ };
+ };
+
+ intc: interrupt-controller@17a00000 {
+ compatible = "arm,gic-v3";
+ reg = <0 0x17a00000 0 0x10000>, /* GICD */
+ <0 0x17a60000 0 0x100000>; /* GICR * 8 */
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <3>;
+ };
+ };
+};
--
2.38.1
On Thu, 10 Nov 2022 19:18:15 -0500, Richard Acayan wrote:
> Changes since v3:
> - remove qcom,msm-id and qcom,board-id (4/4)
>
> Changes since v2:
> - remove intc address and size cells (4/4)
> - move apps_rsc label property down (4/4)
> - move properties in intc (4/4)
> - remove leading zeroes in iommus (4/4)
> - change 0x0 to 0 in regs except cpu (4/4)
> - change 0 to 0x0 in memory regs (4/4)
> - convert hex to decimal in rmi4 #cells properties (4/4)
>
> [...]
Applied, thanks!
[4/4] arm64: dts: qcom: add sdm670 and pixel 3a device trees
commit: 07c8ded6e373830aed55139b2030e755177e1611
Best regards,
--
Bjorn Andersson <[email protected]>