2022-11-17 15:22:48

by Mauro Carvalho Chehab

[permalink] [raw]
Subject: Re: [PATCH v10 05/19] drm/connector: Add TV standard property

On Thu, 17 Nov 2022 10:28:48 +0100
Maxime Ripard <[email protected]> wrote:

> The TV mode property has been around for a while now to select and get the
> current TV mode output on an analog TV connector.
>
> Despite that property name being generic, its content isn't and has been
> driver-specific which makes it hard to build any generic behaviour on top
> of it, both in kernel and user-space.
>
> Let's create a new enum tv norm property, that can contain any of the
> analog TV standards currently supported by kernel drivers. Each driver can
> then pass in a bitmask of the modes it supports, and the property
> creation function will filter out the modes not supported.
>
> We'll then be able to phase out the older tv mode property.
>
> Tested-by: Mateusz Kwiatkowski <[email protected]>
> Signed-off-by: Maxime Ripard <[email protected]>
>
> ---
> Changes in v10:
> - Fix checkpatch warning
>
> Changes in v5:
> - Create an analog TV properties documentation section, and document TV
> Mode there instead of the csv file
>
> Changes in v4:
> - Add property documentation to kms-properties.csv
> - Fix documentation
> ---
> Documentation/gpu/drm-kms.rst | 6 ++
> drivers/gpu/drm/drm_atomic_uapi.c | 4 ++
> drivers/gpu/drm/drm_connector.c | 122 +++++++++++++++++++++++++++++++++++++-
> include/drm/drm_connector.h | 64 ++++++++++++++++++++
> include/drm/drm_mode_config.h | 8 +++
> 5 files changed, 203 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/gpu/drm-kms.rst b/Documentation/gpu/drm-kms.rst
> index b4377a545425..321f2f582c64 100644
> --- a/Documentation/gpu/drm-kms.rst
> +++ b/Documentation/gpu/drm-kms.rst
> @@ -520,6 +520,12 @@ HDMI Specific Connector Properties
> .. kernel-doc:: drivers/gpu/drm/drm_connector.c
> :doc: HDMI connector properties
>
> +Analog TV Specific Connector Properties
> +----------------------------------
> +
> +.. kernel-doc:: drivers/gpu/drm/drm_connector.c
> + :doc: Analog TV Connector Properties
> +
> Standard CRTC Properties
> ------------------------
>
> diff --git a/drivers/gpu/drm/drm_atomic_uapi.c b/drivers/gpu/drm/drm_atomic_uapi.c
> index 7f2b9a07fbdf..d867e7f9f2cd 100644
> --- a/drivers/gpu/drm/drm_atomic_uapi.c
> +++ b/drivers/gpu/drm/drm_atomic_uapi.c
> @@ -700,6 +700,8 @@ static int drm_atomic_connector_set_property(struct drm_connector *connector,
> state->tv.margins.bottom = val;
> } else if (property == config->legacy_tv_mode_property) {
> state->tv.legacy_mode = val;
> + } else if (property == config->tv_mode_property) {
> + state->tv.mode = val;
> } else if (property == config->tv_brightness_property) {
> state->tv.brightness = val;
> } else if (property == config->tv_contrast_property) {
> @@ -810,6 +812,8 @@ drm_atomic_connector_get_property(struct drm_connector *connector,
> *val = state->tv.margins.bottom;
> } else if (property == config->legacy_tv_mode_property) {
> *val = state->tv.legacy_mode;
> + } else if (property == config->tv_mode_property) {
> + *val = state->tv.mode;
> } else if (property == config->tv_brightness_property) {
> *val = state->tv.brightness;
> } else if (property == config->tv_contrast_property) {
> diff --git a/drivers/gpu/drm/drm_connector.c b/drivers/gpu/drm/drm_connector.c
> index 06e737ed15f5..07d449736956 100644
> --- a/drivers/gpu/drm/drm_connector.c
> +++ b/drivers/gpu/drm/drm_connector.c
> @@ -984,6 +984,17 @@ static const struct drm_prop_enum_list drm_dvi_i_subconnector_enum_list[] = {
> DRM_ENUM_NAME_FN(drm_get_dvi_i_subconnector_name,
> drm_dvi_i_subconnector_enum_list)
>
> +static const struct drm_prop_enum_list drm_tv_mode_enum_list[] = {
> + { DRM_MODE_TV_MODE_NTSC, "NTSC" },
> + { DRM_MODE_TV_MODE_NTSC_443, "NTSC-443" },
> + { DRM_MODE_TV_MODE_NTSC_J, "NTSC-J" },
> + { DRM_MODE_TV_MODE_PAL, "PAL" },
> + { DRM_MODE_TV_MODE_PAL_M, "PAL-M" },
> + { DRM_MODE_TV_MODE_PAL_N, "PAL-N" },
> + { DRM_MODE_TV_MODE_SECAM, "SECAM" },
> +};

Nack. It sounds a very bad idea to have standards as generic as
NTSC, PAL, SECAM.

If you take a look at the CCIR/ITU-R specs that define video standards,
you'll see that the standard has actually two components:

1. the composite color TV signal: PAL, NTSC, SECAM, defined in ITU-R BT1700[1]

2. and the conventional analogue TV (the "monochromatic" part),
as defined in ITU-R BT.1701[2], which is, basically, a letter from A to N
(with some country-specific variants, like Nc). Two of those standards
(M and J) are used on Countries with a power grid of 60Hz, as they have
a frame rate of either 30fps or 29.997fps.

[1] https://www.itu.int/rec/R-REC-BT.1700-0-200502-I/en
[2] https://www.itu.int/rec/R-REC-BT.1701-1-200508-I/en

The actual combination is defined within Country-specific laws, which
selects a conventional analogue signal with a composite color one.

So, for instance, US uses NTSC/M (because it uses a 60Hz power grid).
There is a 50Hz variant, called NTSC/443 (not used on any Country, but
present on some European VCR equipments capable of recording at 25fps,
using NTSC).

Btw, some VCR equipments in US may also have PAL/60 with has the
same timings as NTSC, but uses PAL instead.

What happens is that, in Europe, different PAL standards got used, but:

- most TV sets and their chipsets were developed to auto-detect and
support the differences between different systems PAL/B, PAL/G, PAL/D,...
- several of those standards have a difference only at the audio
sub-carriers. So, they look identical for the video decoding part.
- standards may have a different inter-channel space (it can vary from
5 to 8 MHz) to minimize cross-signal interference.

---

Anyway, I strongly suggest to either:

1. align the standards there to what we defined in V4L2. See:
https://linuxtv.org/downloads/v4l-dvb-apis-new/userspace-api/v4l/vidioc-enumstd.html#v4l2-std-id
and:
https://linuxtv.org/downloads/v4l-dvb-apis-new/userspace-api/v4l/standard.html

You can probably start with a subset of those, e. g. with:

- PAL/I, PAL/BG, PAL/DK, PAL/M, PAL/N, PAL/Nc, PAL/60
- NTSC/M, NTSC/M Japan, NTSC/M Korea, NTSC/443
- SECAM/BG, SECAM/DK, SECAM/I, SECAM/L, SECAM/LP

Btw, for decoders, this should actually be a bitmask, as most decoding
chipsets can auto-detect among several different video standards.

2. split into two different properties:
- the "monochromatic" one: A to N, M_Japan, M_Korea,
Nc, 60 and 443;
- the composite signal encoding: NTSC, PAL, SECAM.

If I were to design V4L2 again back the days where commercial digital TV
were not present, I would probably have opted to have two different
properties.

Regards,
Mauro

> +DRM_ENUM_NAME_FN(drm_get_tv_mode_name, drm_tv_mode_enum_list)
> +
> static const struct drm_prop_enum_list drm_tv_select_enum_list[] = {
> { DRM_MODE_SUBCONNECTOR_Automatic, "Automatic" }, /* DVI-I and TV-out */
> { DRM_MODE_SUBCONNECTOR_Composite, "Composite" }, /* TV-out */
> @@ -1552,6 +1563,71 @@ EXPORT_SYMBOL(drm_connector_attach_dp_subconnector_property);
> * infoframe values is done through drm_hdmi_avi_infoframe_content_type().
> */
>
> +/*
> + * TODO: Document the properties:
> + * - left margin
> + * - right margin
> + * - top margin
> + * - bottom margin
> + * - brightness
> + * - contrast
> + * - flicker reduction
> + * - hue
> + * - mode
> + * - overscan
> + * - saturation
> + * - select subconnector
> + * - subconnector
> + */
> +/**
> + * DOC: Analog TV Connector Properties
> + *
> + * TV Mode:
> + * Indicates the TV Mode used on an analog TV connector. The value
> + * of this property can be one of the following:
> + *
> + * NTSC:
> + * TV Mode is CCIR System M (aka 525-lines) together with
> + * the NTSC Color Encoding.
> + *
> + * NTSC-443:
> + *
> + * TV Mode is CCIR System M (aka 525-lines) together with
> + * the NTSC Color Encoding, but with a color subcarrier
> + * frequency of 4.43MHz
> + *
> + * NTSC-J:
> + *
> + * TV Mode is CCIR System M (aka 525-lines) together with
> + * the NTSC Color Encoding, but with a black level equal to
> + * the blanking level.
> + *
> + * PAL:
> + *
> + * TV Mode is CCIR System B (aka 625-lines) together with
> + * the PAL Color Encoding.
> + *
> + * PAL-M:
> + *
> + * TV Mode is CCIR System M (aka 525-lines) together with
> + * the PAL Color Encoding.
> + *
> + * PAL-N:
> + *
> + * TV Mode is CCIR System N together with the PAL Color
> + * Encoding, a color subcarrier frequency of 3.58MHz, the
> + * SECAM color space, and narrower channels than other PAL
> + * variants.
> + *
> + * SECAM:
> + *
> + * TV Mode is CCIR System B (aka 625-lines) together with
> + * the SECAM Color Encoding.
> + *
> + * Drivers can set up this property by calling
> + * drm_mode_create_tv_properties().
> + */
> +
> /**
> * drm_connector_attach_content_type_property - attach content-type property
> * @connector: connector to attach content type property on.
> @@ -1649,6 +1725,10 @@ EXPORT_SYMBOL(drm_mode_create_tv_margin_properties);
> * responsible for allocating a list of format names and passing them to
> * this routine.
> *
> + * NOTE: This functions registers the deprecated "mode" connector
> + * property to select the analog TV mode (ie, NTSC, PAL, etc.). New
> + * drivers must use drm_mode_create_tv_properties() instead.
> + *
> * Returns:
> * 0 on success or a negative error code on failure.
> */
> @@ -1690,7 +1770,6 @@ int drm_mode_create_tv_properties_legacy(struct drm_device *dev,
> if (drm_mode_create_tv_margin_properties(dev))
> goto nomem;
>
> -
> if (num_modes) {
> dev->mode_config.legacy_tv_mode_property =
> drm_property_create(dev, DRM_MODE_PROP_ENUM,
> @@ -1739,6 +1818,47 @@ int drm_mode_create_tv_properties_legacy(struct drm_device *dev,
> }
> EXPORT_SYMBOL(drm_mode_create_tv_properties_legacy);
>
> +/**
> + * drm_mode_create_tv_properties - create TV specific connector properties
> + * @dev: DRM device
> + * @supported_tv_modes: Bitmask of TV modes supported (See DRM_MODE_TV_MODE_*)
> +
> + * Called by a driver's TV initialization routine, this function creates
> + * the TV specific connector properties for a given device.
> + *
> + * Returns:
> + * 0 on success or a negative error code on failure.
> + */
> +int drm_mode_create_tv_properties(struct drm_device *dev,
> + unsigned int supported_tv_modes)
> +{
> + struct drm_prop_enum_list tv_mode_list[DRM_MODE_TV_MODE_MAX];
> + struct drm_property *tv_mode;
> + unsigned int i, len = 0;
> +
> + if (dev->mode_config.tv_mode_property)
> + return 0;
> +
> + for (i = 0; i < DRM_MODE_TV_MODE_MAX; i++) {
> + if (!(supported_tv_modes & BIT(i)))
> + continue;
> +
> + tv_mode_list[len].type = i;
> + tv_mode_list[len].name = drm_get_tv_mode_name(i);
> + len++;
> + }
> +
> + tv_mode = drm_property_create_enum(dev, 0, "TV mode",
> + tv_mode_list, len);
> + if (!tv_mode)
> + return -ENOMEM;
> +
> + dev->mode_config.tv_mode_property = tv_mode;
> +
> + return drm_mode_create_tv_properties_legacy(dev, 0, NULL);
> +}
> +EXPORT_SYMBOL(drm_mode_create_tv_properties);
> +
> /**
> * drm_mode_create_scaling_mode_property - create scaling mode property
> * @dev: DRM device
> diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
> index 15cb58117a94..4927dcb2573f 100644
> --- a/include/drm/drm_connector.h
> +++ b/include/drm/drm_connector.h
> @@ -143,6 +143,65 @@ enum subpixel_order {
>
> };
>
> +/**
> + * enum drm_connector_tv_mode - Analog TV output mode
> + *
> + * This enum is used to indicate the TV output mode used on an analog TV
> + * connector.
> + *
> + * WARNING: The values of this enum is uABI since they're exposed in the
> + * "TV mode" connector property.
> + */
> +enum drm_connector_tv_mode {
> + /**
> + * @DRM_MODE_TV_MODE_NTSC: CCIR System M (aka 525-lines)
> + * together with the NTSC Color Encoding.
> + */
> + DRM_MODE_TV_MODE_NTSC,
> +
> + /**
> + * @DRM_MODE_TV_MODE_NTSC_443: Variant of
> + * @DRM_MODE_TV_MODE_NTSC. Uses a color subcarrier frequency
> + * of 4.43 MHz.
> + */
> + DRM_MODE_TV_MODE_NTSC_443,
> +
> + /**
> + * @DRM_MODE_TV_MODE_NTSC_J: Variant of @DRM_MODE_TV_MODE_NTSC
> + * used in Japan. Uses a black level equals to the blanking
> + * level.
> + */
> + DRM_MODE_TV_MODE_NTSC_J,
> +
> + /**
> + * @DRM_MODE_TV_MODE_PAL: CCIR System B together with the PAL
> + * color system.
> + */
> + DRM_MODE_TV_MODE_PAL,
> +
> + /**
> + * @DRM_MODE_TV_MODE_PAL_M: CCIR System M (aka 525-lines)
> + * together with the PAL color encoding
> + */
> + DRM_MODE_TV_MODE_PAL_M,
> +
> + /**
> + * @DRM_MODE_TV_MODE_PAL_N: CCIR System N together with the PAL
> + * color encoding. It uses 625 lines, but has a color subcarrier
> + * frequency of 3.58MHz, the SECAM color space, and narrower
> + * channels compared to most of the other PAL variants.
> + */
> + DRM_MODE_TV_MODE_PAL_N,
> +
> + /**
> + * @DRM_MODE_TV_MODE_SECAM: CCIR System B together with the
> + * SECAM color system.
> + */
> + DRM_MODE_TV_MODE_SECAM,
> +
> + DRM_MODE_TV_MODE_MAX,
> +};
> +
> /**
> * struct drm_scrambling: sink's scrambling support.
> */
> @@ -696,6 +755,7 @@ struct drm_connector_tv_margins {
> * @subconnector: detected subconnector
> * @margins: TV margins
> * @legacy_mode: Legacy TV mode, driver specific value
> + * @mode: TV mode
> * @brightness: brightness in percent
> * @contrast: contrast in percent
> * @flicker_reduction: flicker reduction in percent
> @@ -708,6 +768,7 @@ struct drm_tv_connector_state {
> enum drm_mode_subconnector subconnector;
> struct drm_connector_tv_margins margins;
> unsigned int legacy_mode;
> + unsigned int mode;
> unsigned int brightness;
> unsigned int contrast;
> unsigned int flicker_reduction;
> @@ -1804,6 +1865,7 @@ const char *drm_get_subpixel_order_name(enum subpixel_order order);
> const char *drm_get_dpms_name(int val);
> const char *drm_get_dvi_i_subconnector_name(int val);
> const char *drm_get_dvi_i_select_name(int val);
> +const char *drm_get_tv_mode_name(int val);
> const char *drm_get_tv_subconnector_name(int val);
> const char *drm_get_tv_select_name(int val);
> const char *drm_get_dp_subconnector_name(int val);
> @@ -1817,6 +1879,8 @@ int drm_mode_create_tv_margin_properties(struct drm_device *dev);
> int drm_mode_create_tv_properties_legacy(struct drm_device *dev,
> unsigned int num_modes,
> const char * const modes[]);
> +int drm_mode_create_tv_properties(struct drm_device *dev,
> + unsigned int supported_tv_modes);
> void drm_connector_attach_tv_margin_properties(struct drm_connector *conn);
> int drm_mode_create_scaling_mode_property(struct drm_device *dev);
> int drm_connector_attach_content_type_property(struct drm_connector *dev);
> diff --git a/include/drm/drm_mode_config.h b/include/drm/drm_mode_config.h
> index c47b29e80108..e5b053001d22 100644
> --- a/include/drm/drm_mode_config.h
> +++ b/include/drm/drm_mode_config.h
> @@ -716,9 +716,17 @@ struct drm_mode_config {
> /**
> * @legacy_tv_mode_property: Optional TV property to select
> * the output TV mode.
> + *
> + * Superseded by @tv_mode_property
> */
> struct drm_property *legacy_tv_mode_property;
>
> + /**
> + * @tv_mode_property: Optional TV property to select the TV
> + * standard output on the connector.
> + */
> + struct drm_property *tv_mode_property;
> +
> /**
> * @tv_left_margin_property: Optional TV property to set the left
> * margin (expressed in pixels).
>