From: Fabien Parent <[email protected]>
This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
Signed-off-by: Fabien Parent <[email protected]>
[[email protected]: Removed parts depending on drivers that aren't upstream yet, cleanups, add L2 cache]
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 163 ++++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 343 ++++++++++++++++++++
3 files changed, 507 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..972843f9e4e9d
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <[email protected]>
+ * Bernhard Rosenkränzer <[email protected]>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+ model = "MediaTek MT8365 Open Platform EVK";
+ compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+
+ key-volume-up {
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ label = "volume_up";
+ linux,code = <KEY_VOLUMEUP>;
+ wakeup-source;
+ debounce-interval = <15>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0xc0000000>;
+ };
+
+ usb_otg_vbus: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee@43200000 {
+ no-map;
+ reg = <0 0x43200000 0 0x00c00000>;
+ };
+ };
+};
+
+&pio {
+ gpio_keys: gpio-keys-pins {
+ pins {
+ pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins {
+ pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+ <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins {
+ pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+ <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ pins {
+ pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+ <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+ };
+ };
+
+ usb_pins: usb-pins {
+ pins-id {
+ pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-usb0-vbus {
+ pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+ output-high;
+ };
+
+ pin-usb1-vbus {
+ pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+ output-high;
+ };
+ };
+
+ pwm_pins: pwm-pins {
+ pins {
+ pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+ <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..2c4ef9b92b68b
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <[email protected]>
+ * Bernhard Rosenkränzer <[email protected]>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "mediatek,mt8365";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus: cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0: cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ clk26m: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_reserved: secmon@43000000 {
+ no-map;
+ reg = <0 0x43000000 0 0x20000>;
+ };
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <4>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x80000>, <0 0x0c080000 0 0x80000>;
+
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8365-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg: syscon@10001000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8365-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ syscfg_pctl: syscfg-pctl@10005000 {
+ compatible = "mediatek,mt8365-syscfg", "syscon";
+ reg = <0 0x10005000 0 0x1000>;
+ };
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8365-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ keypad: keypad@10010000 {
+ compatible = "mediatek,mt6779-keypad";
+ reg = <0 0x10010000 0 0x1000>;
+ wakeup-source;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+ clocks = <&clk26m>;
+ clock-names = "kpd";
+ status = "disabled";
+ };
+
+ mcucfg: syscon@10200000 {
+ compatible = "mediatek,mt8365-mcucfg", "syscon";
+ reg = <0 0x10200000 0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+ sysirq: interrupt-controller@10200a80 {
+ compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10200a80 0 0x20>;
+ };
+
+ infracfg_nao: infracfg@1020e000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x1020e000 0 0x1000>;
+ };
+
+ rng: rng@1020f000 {
+ compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_IFR_TRNG>;
+ clock-names = "rng";
+ };
+
+ apdma: dma-controller@11000280 {
+ compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+ reg = <0 0x11000280 0 0x80>,
+ <0 0x11000300 0 0x80>,
+ <0 0x11000380 0 0x80>,
+ <0 0x11000400 0 0x80>,
+ <0 0x11000580 0 0x80>,
+ <0 0x11000600 0 0x80>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+ dma-requests = <6>;
+ clocks = <&infracfg CLK_IFR_AP_DMA>;
+ clock-names = "apdma";
+ #dma-cells = <1>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x1000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 0>, <&apdma 1>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x1000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 2>, <&apdma 3>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 4>, <&apdma 5>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ pwm: pwm@11006000 {
+ compatible = "mediatek,mt8365-pwm";
+ reg = <0 0x11006000 0 0x1000>;
+ #pwm-cells = <2>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+ <&infracfg CLK_IFR_PWM>,
+ <&infracfg CLK_IFR_PWM1>,
+ <&infracfg CLK_IFR_PWM2>,
+ <&infracfg CLK_IFR_PWM3>;
+ clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+ };
+
+ spi: spi@1100a000 {
+ compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+ <&topckgen CLK_TOP_SPI_SEL>,
+ <&infracfg CLK_IFR_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ ssusb: usb@11201000 {
+ compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+ reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u2port1 PHY_TYPE_USB2>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: usb@11200000 {
+ compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>,
+ <&infracfg CLK_IFR_SSUSB_XHCI>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck",
+ "dma_ck", "xhci_ck";
+ status = "disabled";
+ };
+ };
+
+ u3phy: phy@11cc0000 {
+ compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #phy-cells = <1>;
+ ranges;
+
+ u2port0: usb-phy@11cc0000 {
+ reg = <0 0x11cc0000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u2port1: usb-phy@11cc1000 {
+ reg = <0 0x11cc1000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
+ };
+};
--
2.39.0
Il 14/12/22 00:43, Bernhard Rosenkränzer ha scritto:
> From: Fabien Parent <[email protected]>
>
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
>
> Signed-off-by: Fabien Parent <[email protected]>
> [[email protected]: Removed parts depending on drivers that aren't upstream yet, cleanups, add L2 cache]
> Signed-off-by: Bernhard Rosenkränzer <[email protected]>
> Tested-by: Kevin Hilman <[email protected]>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 163 ++++++++++
> arch/arm64/boot/dts/mediatek/mt8365.dtsi | 343 ++++++++++++++++++++
> 3 files changed, 507 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
>
..snip..
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> new file mode 100644
> index 0000000000000..2c4ef9b92b68b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> @@ -0,0 +1,343 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * (C) 2018 MediaTek Inc.
> + * Copyright (C) 2022 BayLibre SAS
> + * Fabien Parent <[email protected]>
> + * Bernhard Rosenkränzer <[email protected]>
> + */
> +#include <dt-bindings/clock/mediatek,mt8365-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + compatible = "mediatek,mt8365";
> + interrupt-parent = <&sysirq>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + cpus: cpus {
You're not referencing `cpus` anywhere, hence this label is useless:
please remove.
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0: cluster0 {
Same for this one.
> + core0 {
> + cpu = <&cpu0>;
> + };
> + core1 {
> + cpu = <&cpu1>;
> + };
> + core2 {
> + cpu = <&cpu2>;
> + };
> + core3 {
> + cpu = <&cpu3>;
> + };
> + };
> + };
> +
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x0>;
> + #cooling-cells = <2>;
> + enable-method = "psci";
> + next-level-cache = <&l2>;
It would be nice if you described the I/D caches for all CPUs.
> + };
> +
> + cpu1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x1>;
> + #cooling-cells = <2>;
> + enable-method = "psci";
> + next-level-cache = <&l2>;
> + };
> +
> + cpu2: cpu@2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x2>;
> + #cooling-cells = <2>;
> + enable-method = "psci";
> + next-level-cache = <&l2>;
> + };
> +
> + cpu3: cpu@3 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x3>;
> + #cooling-cells = <2>;
> + enable-method = "psci";
> + next-level-cache = <&l2>;
> + };
> +
> + l2: l2-cache {
> + compatible = "cache";
....and what's the size of this L2 cache?
Is it unified, or does each CPU core have its own private L2?
> + };
> + };
> +
> + clk26m: oscillator {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "clk26m";
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* 128 KiB reserved for ARM Trusted Firmware (BL31) */
> + bl31_secmon_reserved: secmon@43000000 {
This depends on the bootloader that's flashed on your board - it's not a
global SoC property.
Please move it to your board, or explain why BL31 *must* always be
128KiB starting at 0x43000000.
> + no-map;
> + reg = <0 0x43000000 0 0x20000>;
> + };
> + };
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
Is there really no systimer in this SoC? Would be pretty odd....
Regards,
Angelo