This series introduces basic support for two Galaxy Tab A
tablets: 8 and 10 inch variants. They share most of the
hardware and are mainly dffernet by the display.
With this series both tablets gain support for things like
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
- WCNSS (WiFi/BT)
- GPIO keys
- Fuel gauge
- Touchscreen
- Accelerometer
In fact, with some additional patches like display and
modem support, that are not included as part of this
series, these tablets can actually reach one's expectations
of what a "normal" tablet should be able to do.
Changes in v2:
- Squashed the commits.
Changes in v3:
- Address Konrad's review comments.
Jasper Korten (1):
arm64: dts: qcom: Add device tree for Samsung Galaxy Tab A 9.7 (2015)
Nikita Travkin (1):
dt-bindings: qcom: Document samsung,gt58 and gt510
Siddharth Manthan (1):
arm64: dts: qcom: Add device tree for Samsung Galaxy Tab A 8.0 (2015)
.../devicetree/bindings/arm/qcom.yaml | 2 +
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../dts/qcom/msm8916-samsung-gt5-common.dtsi | 296 ++++++++++++++++++
.../boot/dts/qcom/msm8916-samsung-gt510.dts | 113 +++++++
.../boot/dts/qcom/msm8916-samsung-gt58.dts | 75 +++++
5 files changed, 488 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt58.dts
--
2.38.1
From: Siddharth Manthan <[email protected]>
Galaxy Tab A 8.0 is a tablet, very similar to Tab A 9.7 with major
differences being the display and touchscreen.
Add it's devicetree reusing a common dtsi from gt510.
Signed-off-by: Siddharth Manthan <[email protected]>
[Squashed multiple commits]
Reviewed-by: Konrad Dybcio <[email protected]>
Signed-off-by: Nikita Travkin <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/msm8916-samsung-gt58.dts | 75 +++++++++++++++++++
2 files changed, 76 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt58.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70e3b109aeff..062561db33f1 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e7.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt510.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt58.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt58.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt58.dts
new file mode 100644
index 000000000000..5d6f8383306b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt58.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-gt5-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy Tab A 8.0 (2015)";
+ compatible = "samsung,gt58", "qcom,msm8916";
+ chassis-type = "tablet";
+
+ reg_vdd_tsp: regulator-vdd-tsp {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_tsp";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <®_tsp_en_default>;
+ pinctrl-names = "default";
+ };
+
+ vibrator {
+ compatible = "gpio-vibrator";
+ enable-gpios = <&msmgpio 76 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&vibrator_en_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c5 {
+ status = "okay";
+
+ touchscreen@20 {
+ compatible = "zinitix,bt532";
+ reg = <0x20>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+
+ touchscreen-size-x = <768>;
+ touchscreen-size-y = <1024>;
+
+ vcca-supply = <®_vdd_tsp>;
+ vdd-supply = <&pm8916_l6>;
+
+ pinctrl-0 = <&tsp_int_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&msmgpio {
+ reg_tsp_en_default: reg-tsp-en-default-state {
+ pins = "gpio73";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_int_default: tsp-int-default-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ vibrator_en_default: vibrator-en-default-state {
+ pins = "gpio76";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
--
2.38.1
From: Jasper Korten <[email protected]>
The Galaxy Tab A 9.7 (2015) is a Snapdragon 410 based tablet.
This commit introduces basic support for the tablet including the
following features:
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- Regulators
- WCNSS (WiFi/BT)
- GPIO keys
- Fuel gauge
- Touchscreen
- Accelerometer
Part of the DT is split out into a common dtsi since the tablet shares
majority of the design with another variant having a different screen
size.
Signed-off-by: Jasper Korten <[email protected]>
Co-developed-by: Siddharth Manthan <[email protected]>
Signed-off-by: Siddharth Manthan <[email protected]>
Co-developed-by: Nikita Travkin <[email protected]>
Signed-off-by: Nikita Travkin <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../dts/qcom/msm8916-samsung-gt5-common.dtsi | 296 ++++++++++++++++++
.../boot/dts/qcom/msm8916-samsung-gt510.dts | 113 +++++++
3 files changed, 410 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index b42362c7be1b..70e3b109aeff 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e7.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt510.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
new file mode 100644
index 000000000000..d920b7247d82
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
@@ -0,0 +1,296 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ reserved-memory {
+ /* Additional memory used by Samsung firmware modifications */
+ tz-apps@85500000 {
+ reg = <0x0 0x85500000 0x0 0xb00000>;
+ no-map;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+
+ label = "GPIO Buttons";
+
+ volume-up-button {
+ label = "Volume Up";
+ gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ home-button {
+ label = "Home";
+ gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOMEPAGE>;
+ };
+ };
+
+ gpio-hall-sensor {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&gpio_hall_sensor_default>;
+ pinctrl-names = "default";
+
+ label = "GPIO Hall Effect Sensor";
+
+ hall-sensor-switch {
+ label = "Hall Effect Sensor";
+ gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ linux,can-disable;
+ };
+ };
+};
+
+&blsp_i2c4 {
+ status = "okay";
+
+ fuelgauge@36 {
+ compatible = "maxim,max77849-battery";
+ reg = <0x36>;
+
+ maxim,rsns-microohm = <10000>;
+ maxim,over-heat-temp = <600>;
+ maxim,over-volt = <4400>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <121 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-0 = <&fuelgauge_int_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c2 {
+ status = "okay";
+
+ light-sensor@10 {
+ compatible = "capella,cm3323";
+ reg = <0x10>;
+ };
+
+ accelerometer@1d {
+ compatible = "st,lis2hh12";
+ reg = <0x1d>;
+
+ vdd-supply = <&pm8916_l17>;
+ vddio-supply = <&pm8916_l5>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "INT1";
+
+ st,drdy-int-pin = <1>;
+ mount-matrix = "0", "1", "0",
+ "-1", "0", "0",
+ "0", "0", "1";
+
+ pinctrl-0 = <&accel_int_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&pm8916_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+/* FIXME: Replace with MAX77849 MUIC when driver is available */
+&pm8916_usbin {
+ status = "okay";
+};
+
+&pronto {
+ status = "okay";
+
+ iris {
+ compatible = "qcom,wcn3660b";
+ };
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+ pinctrl-names = "default", "sleep";
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ pinctrl-names = "default", "sleep";
+
+ cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+};
+
+&usb {
+ dr_mode = "peripheral";
+ extcon = <&pm8916_usbin>;
+
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&pm8916_usbin>;
+};
+
+&smd_rpm_regulators {
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l8 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+};
+
+&msmgpio {
+ accel_int_default: accel-int-default-state {
+ pins = "gpio115";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ fuelgauge_int_default: fuelgauge-int-default-state {
+ pins = "gpio121";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio107", "gpio109";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ gpio_hall_sensor_default: gpio-hall-sensor-default-state {
+ pins = "gpio52";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
new file mode 100644
index 000000000000..607a5dc8a534
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-gt5-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy Tab A 9.7 (2015)";
+ compatible = "samsung,gt510", "qcom,msm8916";
+ chassis-type = "tablet";
+
+ clk_pwm: pwm {
+ compatible = "clk-pwm";
+ #pwm-cells = <2>;
+
+ clocks = <&gcc GCC_GP2_CLK>;
+
+ pinctrl-0 = <&motor_pwm_default>;
+ pinctrl-names = "default";
+ };
+
+ reg_motor_vdd: regulator-motor-vdd {
+ compatible = "regulator-fixed";
+ regulator-name = "motor_vdd";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ gpio = <&msmgpio 76 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&motor_en_default>;
+ pinctrl-names = "default";
+ };
+
+ reg_tsp_1p8v: regulator-tsp-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "tsp_1p8v";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&tsp_en_default>;
+ pinctrl-names = "default";
+ };
+
+ reg_tsp_3p3v: regulator-tsp-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "tsp_3p3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vibrator {
+ compatible = "pwm-vibrator";
+
+ pwms = <&clk_pwm 0 100000>;
+ pwm-names = "enable";
+
+ vcc-supply = <®_motor_vdd>;
+ };
+};
+
+&blsp_i2c5 {
+ status = "okay";
+
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+ vdd-supply = <®_tsp_1p8v>;
+ vdda-supply = <®_tsp_3p3v>;
+
+ reset-gpios = <&msmgpio 114 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&tsp_int_rst_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&msmgpio {
+ motor_en_default: motor-en-default-state {
+ pins = "gpio76";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ motor_pwm_default: motor-pwm-default-state {
+ pins = "gpio50";
+ function = "gcc_gp2_clk_a";
+ };
+
+ tsp_en_default: tsp-en-default-state {
+ pins = "gpio73";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tsp_int_rst_default: tsp-int-rst-default-state {
+ pins = "gpio13", "gpio114";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
--
2.38.1
gt58 and gt510 are Samsung Galaxy Tab A 8.0/9.7 (2015) tablets.
Document their compatibles.
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Nikita Travkin <[email protected]>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 65ef7e442da0..6231df1cc14c 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -207,6 +207,8 @@ properties:
- samsung,e5
- samsung,e7
- samsung,grandmax
+ - samsung,gt510
+ - samsung,gt58
- samsung,j5
- samsung,serranove
- wingtech,wt88047
--
2.38.1
On 7.01.2023 15:19, Nikita Travkin wrote:
> From: Jasper Korten <[email protected]>
>
> The Galaxy Tab A 9.7 (2015) is a Snapdragon 410 based tablet.
>
> This commit introduces basic support for the tablet including the
> following features:
> - SDHCI (internal and external storage)
> - USB Device Mode
> - UART
> - Regulators
> - WCNSS (WiFi/BT)
> - GPIO keys
> - Fuel gauge
> - Touchscreen
> - Accelerometer
>
> Part of the DT is split out into a common dtsi since the tablet shares
> majority of the design with another variant having a different screen
> size.
>
> Signed-off-by: Jasper Korten <[email protected]>
> Co-developed-by: Siddharth Manthan <[email protected]>
> Signed-off-by: Siddharth Manthan <[email protected]>
> Co-developed-by: Nikita Travkin <[email protected]>
> Signed-off-by: Nikita Travkin <[email protected]>
> ---
Reviewed-by: Konrad Dybcio <[email protected]>
Konrad
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/msm8916-samsung-gt5-common.dtsi | 296 ++++++++++++++++++
> .../boot/dts/qcom/msm8916-samsung-gt510.dts | 113 +++++++
> 3 files changed, 410 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index b42362c7be1b..70e3b109aeff 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e7.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt510.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
> new file mode 100644
> index 000000000000..d920b7247d82
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
> @@ -0,0 +1,296 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/dts-v1/;
> +
> +#include "msm8916-pm8916.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + aliases {
> + serial0 = &blsp1_uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0";
> + };
> +
> + reserved-memory {
> + /* Additional memory used by Samsung firmware modifications */
> + tz-apps@85500000 {
> + reg = <0x0 0x85500000 0x0 0xb00000>;
> + no-map;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-0 = <&gpio_keys_default>;
> + pinctrl-names = "default";
> +
> + label = "GPIO Buttons";
> +
> + volume-up-button {
> + label = "Volume Up";
> + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + };
> +
> + home-button {
> + label = "Home";
> + gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_HOMEPAGE>;
> + };
> + };
> +
> + gpio-hall-sensor {
> + compatible = "gpio-keys";
> +
> + pinctrl-0 = <&gpio_hall_sensor_default>;
> + pinctrl-names = "default";
> +
> + label = "GPIO Hall Effect Sensor";
> +
> + hall-sensor-switch {
> + label = "Hall Effect Sensor";
> + gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
> + linux,input-type = <EV_SW>;
> + linux,code = <SW_LID>;
> + linux,can-disable;
> + };
> + };
> +};
> +
> +&blsp_i2c4 {
> + status = "okay";
> +
> + fuelgauge@36 {
> + compatible = "maxim,max77849-battery";
> + reg = <0x36>;
> +
> + maxim,rsns-microohm = <10000>;
> + maxim,over-heat-temp = <600>;
> + maxim,over-volt = <4400>;
> +
> + interrupt-parent = <&msmgpio>;
> + interrupts = <121 IRQ_TYPE_EDGE_FALLING>;
> +
> + pinctrl-0 = <&fuelgauge_int_default>;
> + pinctrl-names = "default";
> + };
> +};
> +
> +&blsp_i2c2 {
> + status = "okay";
> +
> + light-sensor@10 {
> + compatible = "capella,cm3323";
> + reg = <0x10>;
> + };
> +
> + accelerometer@1d {
> + compatible = "st,lis2hh12";
> + reg = <0x1d>;
> +
> + vdd-supply = <&pm8916_l17>;
> + vddio-supply = <&pm8916_l5>;
> +
> + interrupt-parent = <&msmgpio>;
> + interrupts = <115 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "INT1";
> +
> + st,drdy-int-pin = <1>;
> + mount-matrix = "0", "1", "0",
> + "-1", "0", "0",
> + "0", "0", "1";
> +
> + pinctrl-0 = <&accel_int_default>;
> + pinctrl-names = "default";
> + };
> +};
> +
> +&blsp1_uart2 {
> + status = "okay";
> +};
> +
> +&pm8916_resin {
> + linux,code = <KEY_VOLUMEDOWN>;
> + status = "okay";
> +};
> +
> +/* FIXME: Replace with MAX77849 MUIC when driver is available */
> +&pm8916_usbin {
> + status = "okay";
> +};
> +
> +&pronto {
> + status = "okay";
> +
> + iris {
> + compatible = "qcom,wcn3660b";
> + };
> +};
> +
> +&sdhc_1 {
> + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
> + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
> + pinctrl-names = "default", "sleep";
> +
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
> + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
> + pinctrl-names = "default", "sleep";
> +
> + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
> +
> + status = "okay";
> +};
> +
> +&usb {
> + dr_mode = "peripheral";
> + extcon = <&pm8916_usbin>;
> +
> + status = "okay";
> +};
> +
> +&usb_hs_phy {
> + extcon = <&pm8916_usbin>;
> +};
> +
> +&smd_rpm_regulators {
> + vdd_l1_l2_l3-supply = <&pm8916_s3>;
> + vdd_l4_l5_l6-supply = <&pm8916_s4>;
> + vdd_l7-supply = <&pm8916_s4>;
> +
> + s3 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1300000>;
> + };
> +
> + s4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2100000>;
> + };
> +
> + l1 {
> + regulator-min-microvolt = <1225000>;
> + regulator-max-microvolt = <1225000>;
> + };
> +
> + l2 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + };
> +
> + l4 {
> + regulator-min-microvolt = <2050000>;
> + regulator-max-microvolt = <2050000>;
> + };
> +
> + l5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + l6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + l7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + l8 {
> + regulator-min-microvolt = <2850000>;
> + regulator-max-microvolt = <2900000>;
> + };
> +
> + l9 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + l10 {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2800000>;
> + };
> +
> + l11 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-system-load = <200000>;
> + regulator-allow-set-load;
> + };
> +
> + l12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + };
> +
> + l13 {
> + regulator-min-microvolt = <3075000>;
> + regulator-max-microvolt = <3075000>;
> + };
> +
> + l14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + l15 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + l16 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + l17 {
> + regulator-min-microvolt = <2850000>;
> + regulator-max-microvolt = <2850000>;
> + };
> +
> + l18 {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2700000>;
> + };
> +};
> +
> +&msmgpio {
> + accel_int_default: accel-int-default-state {
> + pins = "gpio115";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + fuelgauge_int_default: fuelgauge-int-default-state {
> + pins = "gpio121";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + gpio_keys_default: gpio-keys-default-state {
> + pins = "gpio107", "gpio109";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + gpio_hall_sensor_default: gpio-hall-sensor-default-state {
> + pins = "gpio52";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
> new file mode 100644
> index 000000000000..607a5dc8a534
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts
> @@ -0,0 +1,113 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/dts-v1/;
> +
> +#include "msm8916-samsung-gt5-common.dtsi"
> +
> +/ {
> + model = "Samsung Galaxy Tab A 9.7 (2015)";
> + compatible = "samsung,gt510", "qcom,msm8916";
> + chassis-type = "tablet";
> +
> + clk_pwm: pwm {
> + compatible = "clk-pwm";
> + #pwm-cells = <2>;
> +
> + clocks = <&gcc GCC_GP2_CLK>;
> +
> + pinctrl-0 = <&motor_pwm_default>;
> + pinctrl-names = "default";
> + };
> +
> + reg_motor_vdd: regulator-motor-vdd {
> + compatible = "regulator-fixed";
> + regulator-name = "motor_vdd";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> +
> + gpio = <&msmgpio 76 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&motor_en_default>;
> + pinctrl-names = "default";
> + };
> +
> + reg_tsp_1p8v: regulator-tsp-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "tsp_1p8v";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&tsp_en_default>;
> + pinctrl-names = "default";
> + };
> +
> + reg_tsp_3p3v: regulator-tsp-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "tsp_3p3v";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + vibrator {
> + compatible = "pwm-vibrator";
> +
> + pwms = <&clk_pwm 0 100000>;
> + pwm-names = "enable";
> +
> + vcc-supply = <®_motor_vdd>;
> + };
> +};
> +
> +&blsp_i2c5 {
> + status = "okay";
> +
> + touchscreen@4a {
> + compatible = "atmel,maxtouch";
> + reg = <0x4a>;
> + interrupt-parent = <&msmgpio>;
> + interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
> +
> + vdd-supply = <®_tsp_1p8v>;
> + vdda-supply = <®_tsp_3p3v>;
> +
> + reset-gpios = <&msmgpio 114 GPIO_ACTIVE_LOW>;
> +
> + pinctrl-0 = <&tsp_int_rst_default>;
> + pinctrl-names = "default";
> + };
> +};
> +
> +&msmgpio {
> + motor_en_default: motor-en-default-state {
> + pins = "gpio76";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + motor_pwm_default: motor-pwm-default-state {
> + pins = "gpio50";
> + function = "gcc_gp2_clk_a";
> + };
> +
> + tsp_en_default: tsp-en-default-state {
> + pins = "gpio73";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + tsp_int_rst_default: tsp-int-rst-default-state {
> + pins = "gpio13", "gpio114";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +};
On Sat, 7 Jan 2023 19:19:08 +0500, Nikita Travkin wrote:
> This series introduces basic support for two Galaxy Tab A
> tablets: 8 and 10 inch variants. They share most of the
> hardware and are mainly dffernet by the display.
>
> With this series both tablets gain support for things like
> - SDHCI (internal and external storage)
> - USB Device Mode
> - UART
> - Regulators
> - WCNSS (WiFi/BT)
> - GPIO keys
> - Fuel gauge
> - Touchscreen
> - Accelerometer
>
> [...]
Applied, thanks!
[2/3] arm64: dts: qcom: Add device tree for Samsung Galaxy Tab A 9.7 (2015)
commit: 7cc406151a99ec1643ed8bf3c52fa5fbdf74238f
[3/3] arm64: dts: qcom: Add device tree for Samsung Galaxy Tab A 8.0 (2015)
commit: 41adc65ca5a4a3a651def2ae84ccbef7eed7cb24
Best regards,
--
Bjorn Andersson <[email protected]>