From: Philippe Schenker <[email protected]>
Inheriting the dahlia devicetree leads to inheriting certain settings
for the audio-codec that are not correct and hence the dt schema check
failing.
Remove that include and put all nodes back that had been included.
Signed-off-by: Philippe Schenker <[email protected]>
---
.../boot/dts/freescale/imx8mm-verdin-dev.dtsi | 96 ++++++++++++++++++-
1 file changed, 94 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
index b2bcd2282170..3c4b8ca125e3 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -3,8 +3,6 @@
* Copyright 2022 Toradex
*/
-#include "imx8mm-verdin-dahlia.dtsi"
-
/ {
sound_card: sound-card {
compatible = "simple-audio-card";
@@ -42,27 +40,121 @@ simple-audio-card,cpu {
};
};
+/* Verdin SPI_1 */
+&ecspi2 {
+ status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+ status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+ status = "okay";
+};
+
+&fec1 {
+ status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+ status = "okay";
+};
+
+/* Current measurement into module VCC */
+&hwmon {
+ status = "okay";
+};
+
+&hwmon_temp {
+ vs-supply = <®_1p8v>;
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
&gpio_expander_21 {
status = "okay";
};
/* Verdin I2C_1 */
&i2c4 {
+ status = "okay";
+
/* Audio Codec */
nau8822_1a: audio-codec@1a {
compatible = "nuvoton,nau8822";
reg = <0x1a>;
+ #sound-dai-cells = <0>;
};
};
+/* Verdin PCIE_1 */
+&pcie0 {
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+ status = "okay";
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+ status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+ status = "okay";
+};
+
+/* Verdin I2S_1 */
+&sai2 {
+ status = "okay";
+};
+
+/* Verdin UART_3 */
+&uart1 {
+ status = "okay";
+};
+
/* Verdin UART_1, connector X50 through RS485 transceiver */
&uart2 {
linux,rs485-enabled-at-boot-time;
rs485-rts-active-low;
rs485-rx-during-tx;
+ status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart3 {
+ status = "okay";
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+ disable-over-current;
+ status = "okay";
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+ disable-over-current;
+ status = "okay";
};
/* Limit frequency on dev board due to long traces and bad signal integrity */
&usdhc2 {
max-frequency = <100000000>;
+ status = "okay";
};
--
2.39.0