v8:
- Add binding descriptions for mediatek,mt8365-systimer and
mediatek,mt8365-uart
- Specify ranges with parameters for u3phy
v7:
- Update GIC information in mt8365.dtsi (thanks to Marc Zyngier for
pointing out the problem)
- Adjust the timer to match the updated GIC information
v6:
- Add systimer in mt8365.dtsi
- Add I/D caches and L2 cache details in mt8365.dtsi
- Move bl31_secmon_reserved from mt8365.dtsi to mt8365-evk.dts
- Fix inconsistent indentation in mt8365-pinctrl example
- Further mt8365.dtsi cleanups
- Submit to additional maintainers spotted by get_maintainer.pl
v5:
- Reorder top-level entries in mediatek,mt8365-pinctrl.yaml to match
example-schema
- Use consistent quotes
v4:
- Remove pins-are-numbered references that have been holding things up
now that the patches removing it from dt-bindings have landed in linux-next
v3:
- Remove a number of components that are not yet supported (they will
come back alongside the corresponding drivers)
- Address issues found by dt_binding_check (mostly fixing pinctrl
bindings)
- Address issues pointed out in comments
- Reorder patches
v2:
- Add missing dt-bindings documentation
- Small cleanups addressing issues in v1 pointed out by Krzysztof Kozlowski
Bernhard Rosenkränzer (6):
dt-bindings: arm64: dts: mediatek: Add mt8365-evk board
dt-bindings: irq: mtk, sysirq: add support for mt8365
dt-bindings: mfd: syscon: Add mt8365-syscfg
dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
dt-bindings: timer: mediatek,mtk-timer: add MT8365 SoC bindings
dt-bindings: serial: mediatek,uart: add MT8365 SoC bindings
Fabien Parent (3):
dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
arm64: dts: mediatek: Initial mt8365-evk support
.../devicetree/bindings/arm/mediatek.yaml | 4 +
.../interrupt-controller/mediatek,sysirq.txt | 1 +
.../devicetree/bindings/mfd/syscon.yaml | 1 +
.../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 +++++++++
.../bindings/serial/mediatek,uart.yaml | 1 +
.../bindings/timer/mediatek,mtk-timer.txt | 1 +
.../bindings/usb/mediatek,mtk-xhci.yaml | 1 +
.../bindings/usb/mediatek,mtu3.yaml | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 ++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++
11 files changed, 755 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
--
2.39.1
Add bindings for the Mediatek mt8365-evk board.
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
Documentation/devicetree/bindings/arm/mediatek.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index 2275e5d93721b..ae12b1cab9fbd 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -244,6 +244,10 @@ properties:
- enum:
- mediatek,mt8183-pumpkin
- const: mediatek,mt8183
+ - items:
+ - enum:
+ - mediatek,mt8365-evk
+ - const: mediatek,mt8365
- items:
- enum:
- mediatek,mt8516-pumpkin
--
2.39.1
Document Mediatek mt8365-syscfg
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
index 1b01bd0104316..7beeb0abc4db0 100644
--- a/Documentation/devicetree/bindings/mfd/syscon.yaml
+++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -50,6 +50,7 @@ properties:
- marvell,armada-3700-usb2-host-misc
- mediatek,mt8135-pctl-a-syscfg
- mediatek,mt8135-pctl-b-syscfg
+ - mediatek,mt8365-syscfg
- microchip,lan966x-cpu-syscon
- microchip,sparx5-cpu-syscon
- mstar,msc313-pmsleep
--
2.39.1
Add binding documentation of mediatek,sysirq for mt8365 SoC.
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
---
.../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index 84ced3f4179b9..3ffc60184e445 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -25,6 +25,7 @@ Required properties:
"mediatek,mt6577-sysirq": for MT6577
"mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712
"mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701
+ "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq": for MT8365
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
- reg: Physical base address of the intpol registers and length of memory
--
2.39.1
Add devicetree bindings for Mediatek MT8365 pinctrl driver.
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
.../pinctrl/mediatek,mt8365-pinctrl.yaml | 197 ++++++++++++++++++
1 file changed, 197 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
new file mode 100644
index 0000000000000..4b96884a1afc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
@@ -0,0 +1,197 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8365-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT8365 Pin Controller
+
+maintainers:
+ - Zhiyong Tao <[email protected]>
+ - Bernhard Rosenkränzer <[email protected]>
+
+description: |
+ The MediaTek's MT8365 Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ const: mediatek,mt8365-pinctrl
+
+ reg:
+ maxItems: 1
+
+ mediatek,pctl-regmap:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ maxItems: 1
+ minItems: 1
+ maxItems: 2
+ description: |
+ Should be phandles of the syscfg node.
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+
+ "#interrupt-cells":
+ const: 2
+
+patternProperties:
+ "-pins$":
+ type: object
+ additionalProperties: false
+ patternProperties:
+ "pins$":
+ type: object
+ additionalProperties: false
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and input
+ schmitt.
+ $ref: /schemas/pinctrl/pincfg-node.yaml
+
+ properties:
+ pinmux:
+ description:
+ integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are
+ defined as macros in <soc>-pinfunc.h directly.
+
+ bias-disable: true
+
+ bias-pull-up:
+ description: |
+ Besides generic pinconfig options, it can be used as the pull up
+ settings for 2 pull resistors, R0 and R1. User can configure those
+ special pins.
+
+ bias-pull-down: true
+
+ input-enable: true
+
+ input-disable: true
+
+ output-low: true
+
+ output-high: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ mediatek,drive-strength-adv:
+ description: |
+ Describe the specific driving setup property.
+ For I2C pins, the existing generic driving setup can only support
+ 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
+ can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
+ driving setup, the existing generic setup will be disabled.
+ The specific driving setup is controlled by E1E0EN.
+ When E1=0/E0=0, the strength is 0.125mA.
+ When E1=0/E0=1, the strength is 0.25mA.
+ When E1=1/E0=0, the strength is 0.5mA.
+ When E1=1/E0=1, the strength is 1mA.
+ EN is used to enable or disable the specific driving setup.
+ Valid arguments are described as below:
+ 0: (E1, E0, EN) = (0, 0, 0)
+ 1: (E1, E0, EN) = (0, 0, 1)
+ 2: (E1, E0, EN) = (0, 1, 0)
+ 3: (E1, E0, EN) = (0, 1, 1)
+ 4: (E1, E0, EN) = (1, 0, 0)
+ 5: (E1, E0, EN) = (1, 0, 1)
+ 6: (E1, E0, EN) = (1, 1, 0)
+ 7: (E1, E0, EN) = (1, 1, 1)
+ So the valid arguments are from 0 to 7.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ mediatek,pull-up-adv:
+ description: |
+ Pull up setings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,pull-down-adv:
+ description: |
+ Pull down settings for 2 pull resistors, R0 and R1. User can
+ configure those special pins. Valid arguments are described as below:
+ 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+ 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+ 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+ 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ mediatek,tdsel:
+ description: |
+ An integer describing the steps for output level shifter duty
+ cycle when asserted (high pulse width adjustment). Valid arguments
+ are from 0 to 15.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ mediatek,rdsel:
+ description: |
+ An integer describing the steps for input level shifter duty cycle
+ when asserted (high pulse width adjustment). Valid arguments are
+ from 0 to 63.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ required:
+ - pinmux
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - "#gpio-cells"
+
+allOf:
+ - $ref: pinctrl.yaml#
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+
+ pio-pins {
+ pins {
+ pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
+ mediatek,pull-up-adv = <3>;
+ mediatek,drive-strength-adv = <00>;
+ bias-pull-up;
+ };
+ };
+ };
+ };
--
2.39.1
From: Fabien Parent <[email protected]>
Add binding documentation for the MT8365 SoC.
Signed-off-by: Fabien Parent <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
index 7168110e2f9de..d2655173e108c 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
@@ -28,6 +28,7 @@ properties:
- mediatek,mt8188-mtu3
- mediatek,mt8192-mtu3
- mediatek,mt8195-mtu3
+ - mediatek,mt8365-mtu3
- const: mediatek,mtu3
reg:
--
2.39.1
From: Fabien Parent <[email protected]>
Add binding documentation for the MT8365 SoC.
Signed-off-by: Fabien Parent <[email protected]>
[[email protected]: Cleanups suggested by reviewers]
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
---
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index a3c37944c6305..c119caa9ad168 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -35,6 +35,7 @@ properties:
- mediatek,mt8188-xhci
- mediatek,mt8192-xhci
- mediatek,mt8195-xhci
+ - mediatek,mt8365-xhci
- const: mediatek,mtk-xhci
reg:
--
2.39.1
Add binding description for mediatek,mt8365-systimer
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
---
Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
index 8bbb6e94508b2..b3e797e8aa313 100644
--- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
+++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
@@ -33,6 +33,7 @@ Required properties:
For those SoCs that use CPUX
* "mediatek,mt6795-systimer" for MT6795 compatible timers (CPUX)
+ * "mediatek,mt8365-systimer" for MT8365 compatible timers (CPUX)
- reg: Should contain location and length for timer register.
- clocks: Should contain system clock.
--
2.39.1
From: Fabien Parent <[email protected]>
This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.
Signed-off-by: Fabien Parent <[email protected]>
[[email protected]: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++++
3 files changed, 548 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..275ea3a0e7085
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <[email protected]>
+ * Bernhard Rosenkränzer <[email protected]>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+ model = "MediaTek MT8365 Open Platform EVK";
+ compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ input-name = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys>;
+
+ key-volume-up {
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ label = "volume_up";
+ linux,code = <KEY_VOLUMEUP>;
+ wakeup-source;
+ debounce-interval = <15>;
+ };
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0xc0000000>;
+ };
+
+ usb_otg_vbus: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_reserved: secmon@43000000 {
+ no-map;
+ reg = <0 0x43000000 0 0x20000>;
+ };
+
+ /* 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee@43200000 {
+ no-map;
+ reg = <0 0x43200000 0 0x00c00000>;
+ };
+ };
+};
+
+&pio {
+ gpio_keys: gpio-keys-pins {
+ pins {
+ pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins {
+ pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+ <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins {
+ pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+ <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ pins {
+ pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+ <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+ };
+ };
+
+ usb_pins: usb-pins {
+ pins-id {
+ pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-usb0-vbus {
+ pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+ output-high;
+ };
+
+ pin-usb1-vbus {
+ pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+ output-high;
+ };
+ };
+
+ pwm_pins: pwm-pins {
+ pins {
+ pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+ <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..04c666cab506a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <[email protected]>
+ * Bernhard Rosenkränzer <[email protected]>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ compatible = "mediatek,mt8365";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x0>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x1>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x2>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x3>;
+ #cooling-cells = <2>;
+ enable-method = "psci";
+ i-cache-size = <0x8000>;
+ i-cache-line-size = <64>;
+ i-cache-sets = <256>;
+ d-cache-size = <0x8000>;
+ d-cache-line-size = <64>;
+ d-cache-sets = <256>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ cache-size = <0x80000>;
+ cache-line-size = <64>;
+ cache-sets = <512>;
+ cache-unified;
+ };
+ };
+
+ clk26m: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "clk26m";
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ gic: interrupt-controller@c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x10000>, /* GICD */
+ <0 0x0c080000 0 0x80000>, /* GICR */
+ <0 0x0c400000 0 0x2000>, /* GICC */
+ <0 0x0c410000 0 0x1000>, /* GICH */
+ <0 0x0c420000 0 0x2000>; /* GICV */
+
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ topckgen: syscon@10000000 {
+ compatible = "mediatek,mt8365-topckgen", "syscon";
+ reg = <0 0x10000000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ infracfg: syscon@10001000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x10001000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ pericfg: syscon@10003000 {
+ compatible = "mediatek,mt8365-pericfg", "syscon";
+ reg = <0 0x10003000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ syscfg_pctl: syscfg-pctl@10005000 {
+ compatible = "mediatek,mt8365-syscfg", "syscon";
+ reg = <0 0x10005000 0 0x1000>;
+ };
+
+ pio: pinctrl@1000b000 {
+ compatible = "mediatek,mt8365-pinctrl";
+ reg = <0 0x1000b000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apmixedsys: syscon@1000c000 {
+ compatible = "mediatek,mt8365-apmixedsys", "syscon";
+ reg = <0 0x1000c000 0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ keypad: keypad@10010000 {
+ compatible = "mediatek,mt6779-keypad";
+ reg = <0 0x10010000 0 0x1000>;
+ wakeup-source;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+ clocks = <&clk26m>;
+ clock-names = "kpd";
+ status = "disabled";
+ };
+
+ mcucfg: syscon@10200000 {
+ compatible = "mediatek,mt8365-mcucfg", "syscon";
+ reg = <0 0x10200000 0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+ sysirq: interrupt-controller@10200a80 {
+ compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10200a80 0 0x20>;
+ };
+
+ infracfg_nao: infracfg@1020e000 {
+ compatible = "mediatek,mt8365-infracfg", "syscon";
+ reg = <0 0x1020e000 0 0x1000>;
+ };
+
+ rng: rng@1020f000 {
+ compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+ reg = <0 0x1020f000 0 0x100>;
+ clocks = <&infracfg CLK_IFR_TRNG>;
+ clock-names = "rng";
+ };
+
+ apdma: dma-controller@11000280 {
+ compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+ reg = <0 0x11000280 0 0x80>,
+ <0 0x11000300 0 0x80>,
+ <0 0x11000380 0 0x80>,
+ <0 0x11000400 0 0x80>,
+ <0 0x11000580 0 0x80>,
+ <0 0x11000600 0 0x80>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+ dma-requests = <6>;
+ clocks = <&infracfg CLK_IFR_AP_DMA>;
+ clock-names = "apdma";
+ #dma-cells = <1>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x1000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 0>, <&apdma 1>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x1000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 2>, <&apdma 3>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ uart2: serial@11004000 {
+ compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+ reg = <0 0x11004000 0 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+ clock-names = "baud", "bus";
+ dmas = <&apdma 4>, <&apdma 5>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ pwm: pwm@11006000 {
+ compatible = "mediatek,mt8365-pwm";
+ reg = <0 0x11006000 0 0x1000>;
+ #pwm-cells = <2>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+ <&infracfg CLK_IFR_PWM>,
+ <&infracfg CLK_IFR_PWM1>,
+ <&infracfg CLK_IFR_PWM2>,
+ <&infracfg CLK_IFR_PWM3>;
+ clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+ };
+
+ spi: spi@1100a000 {
+ compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+ reg = <0 0x1100a000 0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+ <&topckgen CLK_TOP_SPI_SEL>,
+ <&infracfg CLK_IFR_SPI0>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk";
+ status = "disabled";
+ };
+
+ ssusb: usb@11201000 {
+ compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+ reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u2port1 PHY_TYPE_USB2>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: usb@11200000 {
+ compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+ reg = <0 0x11200000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_IFR_SSUSB_REF>,
+ <&infracfg CLK_IFR_SSUSB_SYS>,
+ <&infracfg CLK_IFR_ICUSB>,
+ <&infracfg CLK_IFR_SSUSB_XHCI>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck",
+ "dma_ck", "xhci_ck";
+ status = "disabled";
+ };
+ };
+
+ u3phy: phy@11cc0000 {
+ compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #phy-cells = <1>;
+ ranges = <0 0 0x11cc0000 0x9000>;
+
+ u2port0: usb-phy@11cc0000 {
+ reg = <0 0x11cc0000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u2port1: usb-phy@11cc1000 {
+ reg = <0 0x11cc1000 0 0x400>;
+ clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+ <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ system_clk: dummy13m {
+ compatible = "fixed-clock";
+ clock-frequency = <13000000>;
+ #clock-cells = <0>;
+ };
+
+ systimer: timer@10017000 {
+ compatible = "mediatek,mt8365-systimer", "mediatek,mt6795-systimer";
+ reg = <0 0x10017000 0 0x10>;
+ interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&system_clk>;
+ clock-names = "clk13m";
+ };
+};
--
2.39.1
Add binding description for mediatek,mt8365-uart
Signed-off-by: Bernhard Rosenkränzer <[email protected]>
---
Documentation/devicetree/bindings/serial/mediatek,uart.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/serial/mediatek,uart.yaml b/Documentation/devicetree/bindings/serial/mediatek,uart.yaml
index fe098d98af6ee..303d02ca4e1ba 100644
--- a/Documentation/devicetree/bindings/serial/mediatek,uart.yaml
+++ b/Documentation/devicetree/bindings/serial/mediatek,uart.yaml
@@ -45,6 +45,7 @@ properties:
- mediatek,mt8188-uart
- mediatek,mt8192-uart
- mediatek,mt8195-uart
+ - mediatek,mt8365-uart
- mediatek,mt8516-uart
- const: mediatek,mt6577-uart
--
2.39.1
On 23/01/2023 17:38, Bernhard Rosenkränzer wrote:
> Add binding description for mediatek,mt8365-systimer
>
> Signed-off-by: Bernhard Rosenkränzer <[email protected]>
> ---
> Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
Acked-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On 23/01/2023 17:38, Bernhard Rosenkränzer wrote:
> Add binding description for mediatek,mt8365-uart
Subject: drop second/last, redundant "bindings". The "dt-bindings"
prefix is already stating that these are bindings.
>
> Signed-off-by: Bernhard Rosenkränzer <[email protected]>
> ---
Acked-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
Il 23/01/23 17:38, Bernhard Rosenkränzer ha scritto:
> Add binding description for mediatek,mt8365-uart
>
> Signed-off-by: Bernhard Rosenkränzer <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Il 23/01/23 17:38, Bernhard Rosenkränzer ha scritto:
> From: Fabien Parent <[email protected]>
>
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
>
> Signed-off-by: Fabien Parent <[email protected]>
> [[email protected]: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
> Signed-off-by: Bernhard Rosenkränzer <[email protected]>
> Tested-by: Kevin Hilman <[email protected]>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
> arch/arm64/boot/dts/mediatek/mt8365.dtsi | 378 ++++++++++++++++++++
> 3 files changed, 548 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
>
..snip..
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> new file mode 100644
> index 0000000000000..04c666cab506a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> @@ -0,0 +1,378 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * (C) 2018 MediaTek Inc.
> + * Copyright (C) 2022 BayLibre SAS
> + * Fabien Parent <[email protected]>
> + * Bernhard Rosenkränzer <[email protected]>
> + */
> +#include <dt-bindings/clock/mediatek,mt8365-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/thermal/thermal.h>
thermal.h is unused... please remove it for now and add it back in a commit
where you add the thermal node.
Otherwise,
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Bernhard Rosenkränzer <[email protected]> writes:
> v8:
> - Add binding descriptions for mediatek,mt8365-systimer and
> mediatek,mt8365-uart
> - Specify ranges with parameters for u3phy
Built this series on top of v6.2-rc1 and boot tested on mt8365-evk board
locally.
Tested-by: Kevin Hilman <[email protected]>
Kevin
On Mon, 23 Jan 2023, Bernhard Rosenkränzer wrote:
> Document Mediatek mt8365-syscfg
>
> Signed-off-by: Bernhard Rosenkränzer <[email protected]>
> Acked-by: Krzysztof Kozlowski <[email protected]>
> Reviewed-by: Matthias Brugger <[email protected]>
> Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
>
> ---
> Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
> 1 file changed, 1 insertion(+)
Applied, thanks
--
Lee Jones [李琼斯]