This series of patches is meant to address the following:
- Moving of flexcom definitions from board file to SoC file and
some minor changes to its properties.
- Add support for the new sam9x60 curiosity board based on the
existing sam9x60 SoC.
Changes in v6:
--------------
- Added Reviewed-by and Acked-by tags.
All the patches are accepted except the below patches which are
updated based on the comments receied on PATCH v5,
- [PATCH v5 8/8] Enabled the sdmmc1 node in dts.
- [PATCH v5 8/8] Syntax update in dts for sdmmc1 node and i2c0
node.
Changes in v5:
--------------
All the patches are accepted except the below patches which are
updated based on the comments receied on PATCH v4,
- [PATCH v4 2/8] Updated from field and first SOB as same author.
- [PATCH v4 2/8] Added the missing compatibles for the UART.
- [PATCH v4 8/8] Fixed the dtb warnings.
Changes in v4:
--------------
- Added the missed property atmel,usart-mode in uart5
- Renamed the led label.
Changes in v3:
--------------
- Updated commit logs mentioning each author's contribution.
- Author name is updated based on the linux mainline guidelines.
- updated the description file such that sam9x60 curiosity is
added together with sam9x60ek as an enum.
- Updated the entries in the regulator container alphabetically
sorted.
- Added label name and node name following the guidelines.
Changes in v2:
--------------
- Added generic names for regulator node.
- Removed the #addredd-cells and #size-cells property which shows
compilation warning.
- Removed the property "status=okay" as this is default.
- No underscores used for the pinctrl definitions and node names.
- Organised the patches in the logical way.
- Bindings are made separate patch.
Durai Manickam KR (3):
ARM: dts: at91: sam9x60: fix spi4 node
dt-bindings: arm: at91: Add info on sam9x60 curiosity
ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60
curiosity board
Manikandan Muralidharan (5):
ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom
functions
ARM: dts: at91: sam9x60: move flexcom definitions
ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes
ARM: dts: at91: sam9x60: Add missing flexcom definitions
.../devicetree/bindings/arm/atmel-at91.yaml | 6 +-
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 503 ++++++++++++++
arch/arm/boot/dts/at91-sam9x60ek.dts | 50 +-
arch/arm/boot/dts/sam9x60.dtsi | 622 ++++++++++++++++++
5 files changed, 1140 insertions(+), 42 deletions(-)
create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
--
2.25.1
From: Manikandan Muralidharan <[email protected]>
Fixed the label numbering of the flexcom functions so that all
13 flexcom functions of sam9x60 are in the following order when the missing
flexcom functions are added:
flx0: uart0, spi0, i2c0
flx1: uart1, spi1, i2c1
flx2: uart2, spi2, i2c2
flx3: uart3, spi3, i2c3
flx4: uart4, spi4, i2c4
flx5: uart5, spi5, i2c5
flx6: uart6, i2c6
flx7: uart7, i2c7
flx8: uart8, i2c8
flx9: uart9, i2c9
flx10: uart10, i2c10
flx11: uart11, i2c11
flx12: uart12, i2c12
Signed-off-by: Manikandan Muralidharan <[email protected]>
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index d929c1ba5789..cf5d786531f2 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -16,8 +16,8 @@ / {
aliases {
i2c0 = &i2c0;
- i2c1 = &i2c1;
- serial1 = &uart1;
+ i2c1 = &i2c6;
+ serial1 = &uart5;
};
chosen {
@@ -234,7 +234,7 @@ &flx4 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
status = "disabled";
- spi0: spi@400 {
+ spi4: spi@400 {
compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -253,7 +253,7 @@ &flx5 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "okay";
- uart1: serial@200 {
+ uart5: serial@200 {
compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
@@ -279,7 +279,7 @@ &flx6 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
- i2c1: i2c@600 {
+ i2c6: i2c@600 {
compatible = "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -439,7 +439,7 @@ AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE
AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
};
- pinctrl_flx5_default: flx_uart {
+ pinctrl_flx5_default: flx5_uart {
atmel,pins =
<AT91_PIOA 7 AT91_PERIPH_C AT91_PINCTRL_NONE
AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE
--
2.25.1
From: Manikandan Muralidharan <[email protected]>
Move the flexcom definitions from board specific DTS file
to the SoC specific DTSI file for sam9x60ek.
Signed-off-by: Manikandan Muralidharan <[email protected]>
Signed-off-by: Hari Prasath Gujulan Elango <[email protected]>
[[email protected]: Logical split-up of this patch and added
missing UART5 compatibles]
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 33 +------------------
arch/arm/boot/dts/sam9x60.dtsi | 49 ++++++++++++++++++++++++++++
2 files changed, 50 insertions(+), 32 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index cf5d786531f2..4ff84633dd43 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -207,15 +207,10 @@ &flx0 {
status = "okay";
i2c0: i2c@600 {
- compatible = "microchip,sam9x60-i2c";
- reg = <0x600 0x200>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
- atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
@@ -235,14 +230,8 @@ &flx4 {
status = "disabled";
spi4: spi@400 {
- compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
- reg = <0x400 0x200>;
- interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
- clock-names = "spi_clk";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
- atmel,fifo-size = <16>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -254,23 +243,8 @@ &flx5 {
status = "okay";
uart5: serial@200 {
- compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
- reg = <0x200 0x200>;
- atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
- interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
- dmas = <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(10))>,
- <&dma0
- (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
- AT91_XDMAC_DT_PERID(11))>;
- dma-names = "tx", "rx";
- clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
- clock-names = "usart";
- pinctrl-0 = <&pinctrl_flx5_default>;
pinctrl-names = "default";
- atmel,use-dma-rx;
- atmel,use-dma-tx;
+ pinctrl-0 = <&pinctrl_flx5_default>;
status = "okay";
};
};
@@ -280,15 +254,10 @@ &flx6 {
status = "okay";
i2c6: i2c@600 {
- compatible = "microchip,sam9x60-i2c";
- reg = <0x600 0x200>;
- interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx6_default>;
- atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 8f5477e307dd..ee6cc4329ae4 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -170,6 +170,16 @@ flx4: flexcom@f0000000 {
#size-cells = <1>;
ranges = <0x0 0xf0000000 0x800>;
status = "disabled";
+
+ spi4: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx5: flexcom@f0004000 {
@@ -180,6 +190,27 @@ flx5: flexcom@f0004000 {
#size-cells = <1>;
ranges = <0x0 0xf0004000 0x800>;
status = "disabled";
+
+ uart5: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "disabled";
+ };
};
dma0: dma-controller@f0008000 {
@@ -379,6 +410,15 @@ flx6: flexcom@f8010000 {
#size-cells = <1>;
ranges = <0x0 0xf8010000 0x800>;
status = "disabled";
+
+ i2c6: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx7: flexcom@f8014000 {
@@ -409,6 +449,15 @@ flx0: flexcom@f801c000 {
#size-cells = <1>;
ranges = <0x0 0xf801c000 0x800>;
status = "disabled";
+
+ i2c0: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx1: flexcom@f8020000 {
--
2.25.1
The ranges, #address-cells and #size-cells properties are not required,
remove them from the spi4 node.
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index 4ff84633dd43..6b6391d5041e 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -232,8 +232,6 @@ &flx4 {
spi4: spi@400 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
- #address-cells = <1>;
- #size-cells = <0>;
status = "disabled";
};
};
--
2.25.1
From: Manikandan Muralidharan <[email protected]>
The UART submodule in Flexcom has 16-byte Transmit and Receive FIFOs.
Signed-off-by: Manikandan Muralidharan <[email protected]>
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/sam9x60.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index ee6cc4329ae4..1e401a919f56 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -209,6 +209,7 @@ AT91_XDMAC_DT_PER_IF(1) |
clock-names = "usart";
atmel,use-dma-rx;
atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
status = "disabled";
};
};
--
2.25.1
From: Manikandan Muralidharan <[email protected]>
Add dma bindings for flexcom nodes in the soc dtsi file. Users those who
don't wish to use the DMA function for their flexcom functions can
overwrite the dma bindings in the board device tree file.
Signed-off-by: Manikandan Muralidharan <[email protected]>
[[email protected]: fixed code indentation and updated commit log]
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/at91-sam9x60ek.dts | 3 +++
arch/arm/boot/dts/sam9x60.dtsi | 27 +++++++++++++++++++++++++++
2 files changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index 6b6391d5041e..180e4b1aa2f6 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -209,6 +209,7 @@ &flx0 {
i2c0: i2c@600 {
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
i2c-analog-filter;
@@ -230,6 +231,7 @@ &flx4 {
status = "disabled";
spi4: spi@400 {
+ dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
status = "disabled";
@@ -254,6 +256,7 @@ &flx6 {
i2c6: i2c@600 {
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx6_default>;
i2c-analog-filter;
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 1e401a919f56..8442971458e4 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -177,6 +177,15 @@ spi4: spi@400 {
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
atmel,fifo-size = <16>;
status = "disabled";
};
@@ -417,6 +426,15 @@ i2c6: i2c@600 {
reg = <0x600 0x200>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
atmel,fifo-size = <16>;
status = "disabled";
};
@@ -456,6 +474,15 @@ i2c0: i2c@600 {
reg = <0x600 0x200>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
atmel,fifo-size = <16>;
status = "disabled";
};
--
2.25.1
From: Manikandan Muralidharan <[email protected]>
Added the missing flexcom functions for all the flexcom nodes.
Signed-off-by: Manikandan Muralidharan <[email protected]>
[[email protected]: added missing UART compatibles]
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/sam9x60.dtsi | 545 +++++++++++++++++++++++++++++++++
1 file changed, 545 insertions(+)
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index 8442971458e4..91225f0fb984 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -171,6 +171,27 @@ flx4: flexcom@f0000000 {
ranges = <0x0 0xf0000000 0x800>;
status = "disabled";
+ uart4: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
spi4: spi@400 {
compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
@@ -189,6 +210,24 @@ AT91_XDMAC_DT_PER_IF(1) |
atmel,fifo-size = <16>;
status = "disabled";
};
+
+ i2c4: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx5: flexcom@f0004000 {
@@ -221,6 +260,43 @@ AT91_XDMAC_DT_PER_IF(1) |
atmel,fifo-size = <16>;
status = "disabled";
};
+
+ spi5: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
dma0: dma-controller@f0008000 {
@@ -292,6 +368,45 @@ flx11: flexcom@f0020000 {
#size-cells = <1>;
ranges = <0x0 0xf0020000 0x800>;
status = "disabled";
+
+ uart11: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx12: flexcom@f0024000 {
@@ -302,6 +417,45 @@ flx12: flexcom@f0024000 {
#size-cells = <1>;
ranges = <0x0 0xf0024000 0x800>;
status = "disabled";
+
+ uart12: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
pit64b: timer@f0028000 {
@@ -421,6 +575,27 @@ flx6: flexcom@f8010000 {
ranges = <0x0 0xf8010000 0x800>;
status = "disabled";
+ uart6: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
i2c6: i2c@600 {
compatible = "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -448,6 +623,45 @@ flx7: flexcom@f8014000 {
#size-cells = <1>;
ranges = <0x0 0xf8014000 0x800>;
status = "disabled";
+
+ uart7: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx8: flexcom@f8018000 {
@@ -458,6 +672,45 @@ flx8: flexcom@f8018000 {
#size-cells = <1>;
ranges = <0x0 0xf8018000 0x800>;
status = "disabled";
+
+ uart8: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx0: flexcom@f801c000 {
@@ -469,6 +722,46 @@ flx0: flexcom@f801c000 {
ranges = <0x0 0xf801c000 0x800>;
status = "disabled";
+ uart0: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi0: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
i2c0: i2c@600 {
compatible = "microchip,sam9x60-i2c";
reg = <0x600 0x200>;
@@ -496,6 +789,64 @@ flx1: flexcom@f8020000 {
#size-cells = <1>;
ranges = <0x0 0xf8020000 0x800>;
status = "disabled";
+
+ uart1: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi1: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx2: flexcom@f8024000 {
@@ -506,6 +857,64 @@ flx2: flexcom@f8024000 {
#size-cells = <1>;
ranges = <0x0 0xf8024000 0x800>;
status = "disabled";
+
+ uart2: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi2: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx3: flexcom@f8028000 {
@@ -516,6 +925,64 @@ flx3: flexcom@f8028000 {
#size-cells = <1>;
ranges = <0x0 0xf8028000 0x800>;
status = "disabled";
+
+ uart3: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi3: spi@400 {
+ compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
macb0: ethernet@f802c000 {
@@ -581,6 +1048,45 @@ flx9: flexcom@f8040000 {
#size-cells = <1>;
ranges = <0x0 0xf8040000 0x800>;
status = "disabled";
+
+ uart9: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
flx10: flexcom@f8044000 {
@@ -591,6 +1097,45 @@ flx10: flexcom@f8044000 {
#size-cells = <1>;
ranges = <0x0 0xf8044000 0x800>;
status = "disabled";
+
+ uart10: serial@200 {
+ compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@600 {
+ compatible = "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
};
isi: isi@f8048000 {
--
2.25.1
Adding the sam9x60 curiosity board from Microchip into the atmel AT91 board
description yaml file.
Signed-off-by: Durai Manickam KR <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
Documentation/devicetree/bindings/arm/atmel-at91.yaml | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
index 2224b18801a1..dfb8fd089197 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
@@ -91,9 +91,11 @@ properties:
- const: atmel,sama5d2
- const: atmel,sama5
- - description: SAM9X60-EK board
+ - description: Microchip SAM9X60 Evaluation Boards
items:
- - const: microchip,sam9x60ek
+ - enum:
+ - microchip,sam9x60ek
+ - microchip,sam9x60-curiosity
- const: microchip,sam9x60
- const: atmel,at91sam9
--
2.25.1
Add device tree file for sam9x60 curiosity board.
Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 503 +++++++++++++++++++
2 files changed, 504 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6aa7dc4db2fc..da20980384c4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -51,6 +51,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91sam9x25ek.dtb \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM9X60) += \
+ at91-sam9x60_curiosity.dtb \
at91-sam9x60ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2-2.dtb \
diff --git a/arch/arm/boot/dts/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
new file mode 100644
index 000000000000..cb86a3a170ce
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sam9x60_curiosity.dts
@@ -0,0 +1,503 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x60_curiosity.dts - Device Tree file for Microchip SAM9X60 Curiosity board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Durai Manickam KR <[email protected]>
+ */
+/dts-v1/;
+#include "sam9x60.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Microchip SAM9X60 Curiosity";
+ compatible = "microchip,sam9x60-curiosity", "microchip,sam9x60", "atmel,at91sam9";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c6;
+ serial2 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@20000000 {
+ reg = <0x20000000 0x8000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <24000000>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+ button-user {
+ label = "PB_USER";
+ gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PROG1>;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led-red {
+ label = "red";
+ gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-green {
+ label = "green";
+ gpios = <&pioD 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-blue {
+ label = "blue";
+ gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+
+ vdd_1v8: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "VDD_1V8";
+ };
+
+ vdd_1v15: regulator-1 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <1150000>;
+ regulator-min-microvolt = <1150000>;
+ regulator-name = "VDD_1V15";
+ };
+
+ vdd1_3v3: regulator-2 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "VDD1_3V3";
+ };
+};
+
+&adc {
+ vddana-supply = <&vdd1_3v3>;
+ vref-supply = <&vdd1_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+ status = "okay";
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_rx_tx>;
+ status = "disabled"; /* Conflict with dbgu. */
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_rx_tx>;
+ status = "okay";
+};
+
+&dbgu {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dbgu>;
+ status = "okay"; /* Conflict with can0. */
+};
+
+&ebi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_lsb>;
+ status = "okay";
+
+ nand_controller: nand-controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
+ status = "okay";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ uboot@40000 {
+ label = "u-boot";
+ reg = <0x40000 0xc0000>;
+ };
+
+ ubootenvred@100000 {
+ label = "U-Boot Env Redundant";
+ reg = <0x100000 0x40000>;
+ };
+
+ ubootenv@140000 {
+ label = "U-Boot Env";
+ reg = <0x140000 0x40000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x1f800000>;
+ };
+ };
+ };
+ };
+};
+
+&flx0 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c0: i2c@600 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
+ status = "okay";
+
+ eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+ };
+};
+
+&flx6 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c6: i2c@600 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx6_default>;
+ i2c-analog-filter;
+ i2c-digital-filter;
+ i2c-digital-filter-width-ns = <35>;
+ status = "disabled";
+ };
+};
+
+&flx7 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "okay";
+
+ uart7: serial@200 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx7_default>;
+ status = "okay";
+ };
+};
+
+&macb0 {
+ phy-mode = "rmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_macb0_rmii>;
+ status = "okay";
+
+ ethernet-phy@0 {
+ reg = <0x0>;
+ };
+};
+
+&pinctrl {
+ adc {
+ pinctrl_adc_default: adc-default {
+ atmel,pins = <AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_adtrg_default: adtrg-default {
+ atmel,pins = <AT91_PIOB 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ can0 {
+ pinctrl_can0_rx_tx: can0-rx-tx {
+ atmel,pins =
+ <AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX0 */
+ AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANTX0 */
+ AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
+ };
+ };
+
+ can1 {
+ pinctrl_can1_rx_tx: can1-rx-tx {
+ atmel,pins =
+ <AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANRX1 */
+ AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE /* CANTX1 */
+ AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
+ };
+ };
+
+ dbgu {
+ pinctrl_dbgu: dbgu-0 {
+ atmel,pins = <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+ };
+ };
+
+ ebi {
+ pinctrl_ebi_data_lsb: ebi-data-lsb {
+ atmel,pins =
+ <AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+ };
+
+ pinctrl_ebi_addr_nand: ebi-addr-nand {
+ atmel,pins =
+ <AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+ };
+ };
+
+ flexcom {
+ pinctrl_flx0_default: flx0-twi {
+ atmel,pins =
+ <AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_flx6_default: flx6-twi {
+ atmel,pins =
+ <AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+ AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_flx7_default: flx7-usart {
+ atmel,pins =
+ <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+ AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+ };
+ };
+
+ gpio-keys {
+ pinctrl_key_gpio_default: pinctrl-key-gpio {
+ atmel,pins = <AT91_PIOA 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ leds {
+ pinctrl_gpio_leds: gpio-leds {
+ atmel,pins = <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ macb0 {
+ pinctrl_macb0_rmii: macb0-rmii-0 {
+ atmel,pins =
+ <AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB0 periph A */
+ AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB1 periph A */
+ AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB2 periph A */
+ AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB3 periph A */
+ AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB4 periph A */
+ AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB5 periph A */
+ AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB6 periph A */
+ AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB7 periph A */
+ AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE /* PB9 periph A */
+ AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>; /* PB10 periph A */
+ };
+ };
+
+ nand {
+ pinctrl_nand_oe_we: nand-oe-we-0 {
+ atmel,pins =
+ <AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+ AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+ };
+
+ pinctrl_nand_rb: nand-rb-0 {
+ atmel,pins =
+ <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+
+ pinctrl_nand_cs: nand-cs-0 {
+ atmel,pins =
+ <AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+ };
+ };
+
+ pwm0 {
+ pinctrl_pwm0_0: pwm0-0 {
+ atmel,pins = <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_1: pwm0-1 {
+ atmel,pins = <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_pwm0_2: pwm0-2 {
+ atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+ };
+
+ sdmmc0 {
+ pinctrl_sdmmc0_default: sdmmc0 {
+ atmel,pins =
+ <AT91_PIOA 17 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA17 CK periph A with pullup */
+ AT91_PIOA 16 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA16 CMD periph A with pullup */
+ AT91_PIOA 15 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA15 DAT0 periph A */
+ AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA18 DAT1 periph A with pullup */
+ AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA19 DAT2 periph A with pullup */
+ AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA20 DAT3 periph A with pullup */
+ };
+
+ pinctrl_sdmmc0_cd: sdmmc0-cd {
+ atmel,pins =
+ <AT91_PIOA 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ sdmmc1 {
+ pinctrl_sdmmc1_default: sdmmc1 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_B (AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA13 CK periph B */
+ AT91_PIOA 12 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA12 CMD periph B with pullup */
+ AT91_PIOA 11 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA11 DAT0 periph B with pullup */
+ AT91_PIOA 2 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA2 DAT1 periph B with pullup */
+ AT91_PIOA 3 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI) /* PA3 DAT2 periph B with pullup */
+ AT91_PIOA 4 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>; /* PA4 DAT3 periph B with pullup */
+ };
+ };
+
+ usb0 {
+ pinctrl_usba_vbus: usba-vbus {
+ atmel,pins = <AT91_PIOA 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ usb1 {
+ pinctrl_usb_default: usb-default {
+ atmel,pins = <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+ AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+}; /* pinctrl */
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_0 &pinctrl_pwm0_1 &pinctrl_pwm0_2>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
+ cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ disable-wp;
+ status = "okay";
+};
+
+&shutdown_controller {
+ debounce-delay-us = <976>;
+ status = "okay";
+
+ input@0 {
+ reg = <0>;
+ };
+};
+
+&tcb0 {
+ timer0: timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>;
+ };
+
+ timer1: timer@1 {
+ compatible = "atmel,tcb-timer";
+ reg = <1>;
+ };
+};
+
+&usb0 {
+ atmel,vbus-gpio = <&pioA 27 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <0
+ &pioD 18 GPIO_ACTIVE_HIGH
+ &pioD 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
--
2.25.1
On 07.02.2023 13:06, Durai Manickam KR wrote:
> This series of patches is meant to address the following:
> - Moving of flexcom definitions from board file to SoC file and
> some minor changes to its properties.
> - Add support for the new sam9x60 curiosity board based on the
> existing sam9x60 SoC.
>
[ ... ]
>
> Durai Manickam KR (3):
> ARM: dts: at91: sam9x60: fix spi4 node
> dt-bindings: arm: at91: Add info on sam9x60 curiosity
> ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60
> curiosity board
>
> Manikandan Muralidharan (5):
> ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom
> functions
> ARM: dts: at91: sam9x60: move flexcom definitions
> ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
> ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes
> ARM: dts: at91: sam9x60: Add missing flexcom definitions
>
> .../devicetree/bindings/arm/atmel-at91.yaml | 6 +-
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-sam9x60_curiosity.dts | 503 ++++++++++++++
> arch/arm/boot/dts/at91-sam9x60ek.dts | 50 +-
> arch/arm/boot/dts/sam9x60.dtsi | 622 ++++++++++++++++++
> 5 files changed, 1140 insertions(+), 42 deletions(-)
> create mode 100644 arch/arm/boot/dts/at91-sam9x60_curiosity.dts
>
Applied to at91-dt, thanks!