As should be clear for the title and patch title, this is adding initial
support for the OMAP 4460 SOM and dev kit for Phytec's PCM959 evaluation
kit.
The PCM049 is a legacy SOM offered by Phytec:
https://www.phytec.com/legacy-soms/
There was a vendor BSP offered by Phytec, but that never entered the
Device Tree era. This patch is meant to change that.
My development bootloader has moved to U-Boot, but I have verified
Barebox works in the past. When booting from SD card, either bootloader
should work. When booting from Barebox, the NAND OOB layout is
incompatible between the bootloader and the kernel.
I haven't had any OOB / ECC errors in the NAND at all, which was my
main concern. Due to that, I'm submitting this as a patch instead of
an RFC. Hardware ECC correction seems to be fully functional.
v2->v3
* Acked-by on patch 1
* Code review changes (see patch 2 for details)
* Fix intermittent NAND failures (patch 2)
v1->v2
* Almost everything moved into the SOM (PCM-049) .dtsi. Only the
LED chip is dev-board specific.
* Fix pinmux associations (*pmx_core was applying *pmx_wkup
entries... I'm surprised that didn't cause more issues)
* Documentation added
* Updates from review:
* Board compatible strings added
* Hyphen / underscore changes
* Remove unnecessary status="okay" entries
* Generic names used (regulator, led-1, etc.)
Colin Foster (2):
dt-bindings: arm: omap: add phytec pcm-049 som and pcm-959 dev board
arm: dts: omap4: pcm959: add initial support for phytec pcm959
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi | 400 ++++++++++++++++++
arch/arm/boot/dts/omap4-phytec-pcm-959.dts | 48 +++
4 files changed, 452 insertions(+)
create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-959.dts
--
2.25.1
Add documentation for additional OMAP SOMs and development platforms,
provided by Phytec as the PCM-049 SOM and the PCM-959 development kit.
Signed-off-by: Colin Foster <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
v2->v3
* Add Krzysztof Acked
v1->v2
* New patch
---
Documentation/devicetree/bindings/arm/omap/omap.txt | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index fa8b31660cad..0a28215dfa12 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -131,6 +131,9 @@ Boards (incomplete list of examples):
- OMAP4 PandaBoard : Low cost community board
compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"
+- OMAP4 PCM-959 : Commercial dev kit with PCM-049 SOM
+ compatible = "phytec,pcm959", "phytec,pcm049", "ti,omap4460", "ti,omap4430", "ti,omap4";
+
- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board
compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
--
2.25.1
The Phytec PCM-959 is a development platform for the Phytec PCM-049 SOM.
Add initial functionality for the board. The verified interfaces and
peripherals are listed below for the SOM (PCM-049) and the dev board
(PCM-959)
The omap2plus_defconfig was used for testing. Only the On-board LEDs
required CONFIG_LEDS_PCA9532 addition.
PCM-049:
i2c1
* EEPROM at 0x50
* TMP102 (hwmon) at 0x4b
twl6030
GPMC
* Ethernet
* Flash
Serial (ttyS2 console)
PCM959:
MMC1
On-board LEDs (with CONFIG_LEDS_PCA9532)
Signed-off-by: Colin Foster <[email protected]>
---
v2->v3
Code review changes:
* Remove unnecessary "okay" statuses
* Utilize gpio funciton / color instead of label
* Clean up pinctrl whitespace
* Change label of TWL6030 to "pmic"
* Clean up general whitespace
Behavioral changes:
* Utilize "gpmc-wait" instead of "rb-gpios". The initial
configuration would suffer about a 1/100K NAND access
failure, snowballing into corrupted NAND after enough
boot cycles / downloads. This one was fun to figure out!
* Adjustments to gpmc-nand timings from testing.
v1->v2
* Almost everything moved to the SOM (PCM049)
* Fix where omap_pmx_wkup were actually getting applied to
omap_pmx_core.
* Use hyphens instead of underscores for names
* Remove unnecessary entries of "status=okay"
* Use generic "regulator" and "led" names
* add compatible strings for the dev board and SOM
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi | 400 ++++++++++++++++++++
arch/arm/boot/dts/omap4-phytec-pcm-959.dts | 48 +++
3 files changed, 449 insertions(+)
create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
create mode 100644 arch/arm/boot/dts/omap4-phytec-pcm-959.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6aa7dc4db2fc..ae8338cb5bb1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -968,6 +968,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
omap4-panda.dtb \
omap4-panda-a4.dtb \
omap4-panda-es.dtb \
+ omap4-phytec-pcm-959.dtb \
omap4-sdp.dtb \
omap4-sdp-es23plus.dtb \
omap4-var-dvk-om44.dtb \
diff --git a/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi b/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
new file mode 100644
index 000000000000..3cc029599224
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-phytec-pcm-049.dtsi
@@ -0,0 +1,400 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 Innovative Advantage, Inc.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dsp_memory_region: dsp-memory@98000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x98000000 0x800000>;
+ reusable;
+ };
+
+ ipu_memory_region: ipu-memory@98800000 {
+ compatible = "shared-dma-pool";
+ reg = <0x98800000 0x7000000>;
+ reusable;
+ };
+ };
+
+ chosen {
+ stdout-path = &uart3;
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_gpio_pins>;
+
+ led-0 {
+ function = LED_FUNCTION_HEARTBEAT;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio5 0x18 GPIO_ACTIVE_HIGH>; /* GPIO 152 */
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_DISK;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio5 0x19 GPIO_ACTIVE_HIGH>; /* GPIO 153 */
+ linux,default-trigger = "mmc0";
+ };
+ };
+};
+
+&gpio1_target {
+ ti,no-reset-on-init;
+};
+
+&omap4_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&tps62361_pins>;
+
+ i2c1_pins: pinmux-i2c1-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
+ OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ >;
+ };
+
+ i2c3_pins: pinmux-i2c3-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
+ OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ >;
+ };
+
+ i2c4_pins: pinmux-i2c4-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
+ OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
+ >;
+ };
+
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE1) /* uart1_rx */
+ OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE1) /* uart1_tx */
+ >;
+ };
+
+ uart2_pins: pinmux-uart2-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
+ OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */
+ OMAP4_IOPAD(0x11c, PIN_INPUT | MUX_MODE0) /* uart2_rx */
+ OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
+ >;
+ };
+
+ uart3_pins: pinmux-uart3-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x140, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts */
+ OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE0) /* uart3_rts */
+ OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx */
+ OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
+ >;
+ };
+
+ led_gpio_pins: pinmux-leds-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x156, PIN_OUTPUT | MUX_MODE3) /* gpio_152 */
+ OMAP4_IOPAD(0x158, PIN_OUTPUT | MUX_MODE3) /* gpio_153 */
+ >;
+ };
+
+ pinctrl_tempsense: pinmux-pinctrl-tempsense-pins{
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x154, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_151 */
+ >;
+ };
+
+ gpmc_pins: gpmc-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x40, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0 */
+ OMAP4_IOPAD(0x42, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1 */
+ OMAP4_IOPAD(0x44, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2 */
+ OMAP4_IOPAD(0x46, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3 */
+ OMAP4_IOPAD(0x48, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4 */
+ OMAP4_IOPAD(0x4a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5 */
+ OMAP4_IOPAD(0x4c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6 */
+ OMAP4_IOPAD(0x4e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7 */
+ OMAP4_IOPAD(0x50, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad8 */
+ OMAP4_IOPAD(0x52, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad9 */
+ OMAP4_IOPAD(0x54, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad10 */
+ OMAP4_IOPAD(0x56, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad11 */
+ OMAP4_IOPAD(0x58, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad12 */
+ OMAP4_IOPAD(0x5a, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad13 */
+ OMAP4_IOPAD(0x5c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad14 */
+ OMAP4_IOPAD(0x5e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad15 */
+
+ OMAP4_IOPAD(0x60, PIN_OUTPUT | MUX_MODE0) /* gpmc_a16 */
+ OMAP4_IOPAD(0x62, PIN_OUTPUT | MUX_MODE0) /* gpmc_a17 */
+ OMAP4_IOPAD(0x64, PIN_OUTPUT | MUX_MODE0) /* gpmc_a18 */
+ OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE0) /* gpmc_a19 */
+ OMAP4_IOPAD(0x68, PIN_OUTPUT | MUX_MODE0) /* gpmc_a20 */
+ OMAP4_IOPAD(0x6a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a21 */
+ OMAP4_IOPAD(0x6c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a22 */
+ OMAP4_IOPAD(0x6e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a23 */
+
+ OMAP4_IOPAD(0x82, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_noe */
+ OMAP4_IOPAD(0x84, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nwe */
+
+ OMAP4_IOPAD(0x7c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nwp */
+ OMAP4_IOPAD(0x80, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nadv_ale */
+ OMAP4_IOPAD(0x86, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* gpmc_nbe0_cle */
+ OMAP4_IOPAD(0x8a, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */
+ OMAP4_IOPAD(0x8c, PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait1 */
+
+ OMAP4_IOPAD(0x74, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs0 */
+ OMAP4_IOPAD(0x76, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs1 */
+ OMAP4_IOPAD(0x92, PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_ncs5 */
+ >;
+ };
+
+ ethernet_pins: ethernet-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x114, PIN_INPUT | MUX_MODE3) /* gpio_121 */
+ >;
+ };
+
+ tps62361_pins: pinmux-tps62361-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x19c, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpio_182 */
+ >;
+ };
+
+ mmc1_pins: pinmux-mmc1-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
+ OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
+ OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
+ OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
+ OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
+ OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
+ >;
+ };
+};
+
+&omap4_pmx_wkup {
+ pinctrl-names = "default";
+ pinctrl-0= <&smartreflex_i2c_pins &fref_xtal_in_pins
+ &fref_clk3_out_pins &sys_pins>;
+
+ ethernet_wkgpio_pins: pinmux-ethernet-wkup-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x66, PIN_OUTPUT | MUX_MODE3) /* gpio_wk29 */
+ >;
+ };
+
+ smartreflex_i2c_pins: pinmux-smartreflex-i2c-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x4a, PIN_INPUT_PULLUP | MUX_MODE0) /* sr_scl */
+ OMAP4_IOPAD(0x4c, PIN_INPUT_PULLUP | MUX_MODE0) /* sr_sda */
+ >;
+ };
+
+ fref_xtal_in_pins: pinmux-fref-xtal-in-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x4e, PIN_OUTPUT | MUX_MODE0) /* fref_xtal_in */
+ >;
+ };
+
+ fref_clk3_out_pins: pinmux-usb-refclk-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x58, PIN_OUTPUT | MUX_MODE0) /* fref_clk3_out */
+ >;
+ };
+
+ sys_pins: pinmux-sys-pins {
+ pinctrl-single,pins = <
+ OMAP4_IOPAD(0x5e, PIN_INPUT | MUX_MODE0) /* sys_32k */
+ OMAP4_IOPAD(0x60, PIN_OUTPUT | MUX_MODE0) /* sys_nrespwron */
+ OMAP4_IOPAD(0x62, PIN_OUTPUT | MUX_MODE0) /* sys_nreswarm */
+ OMAP4_IOPAD(0x64, PIN_OUTPUT_PULLUP | MUX_MODE0) /* sys_pwr_req */
+ OMAP4_IOPAD(0x68, PIN_INPUT | MUX_MODE0) /* sys_boot6 */
+ OMAP4_IOPAD(0x6a, PIN_INPUT | MUX_MODE0) /* sys_boot7 */
+ >;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+
+ twl: pmic@48 {
+ compatible = "ti,twl6030";
+ reg = <0x48>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
+ };
+
+ core_vdd_reg: regulator@60 {
+ compatible = "ti,tps62361";
+ reg = <0x60>;
+
+ regulator-name = "tps62361-vout";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-coupled-max-spread = <300000>;
+ regulator-max-step-microvolt = <100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ti,vsel0-gpio = <&gpio5 22 GPIO_ACTIVE_HIGH>;
+ ti,vsel0-state-high;
+ };
+
+ temperature-sensor@4b {
+ compatible = "ti,tmp102";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tempsense>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+};
+
+#include "twl6030.dtsi"
+#include "twl6030_omap4.dtsi"
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ status = "okay";
+
+ clock-frequency = <100000>;
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ status = "disabled";
+
+ clock-frequency = <400000>;
+};
+
+&vmmc {
+ ti,retain-on-reset;
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+
+ vmmc-supply = <&vmmc>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mmc4 {
+ status = "disabled";
+};
+
+&mmc5 {
+ status = "disabled";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "okay";
+};
+
+&uart4 {
+ status = "disabled";
+};
+
+&elm {
+ status = "okay";
+};
+
+#include "omap-gpmc-smsc9221.dtsi"
+
+&gpmc {
+ ranges = <5 0 0x2c000000 0x01000000>,
+ <0 0 0x08000000 0x01000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc_pins>;
+ status = "okay";
+
+ nandflash: nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>;
+ interrupt-parent = <&gpmc>;
+
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+ ti,elm-id=<&elm>;
+ linux,mtd-name = "micron,nand";
+ gpmc,device-nand = "true";
+ gpmc,device-width = <1>;
+
+ gpmc,cs-rd-off-ns = <40>;
+ gpmc,cs-wr-off-ns = <40>;
+ gpmc,adv-rd-off-ns = <25>;
+ gpmc,adv-wr-off-ns = <40>;
+ gpmc,oe-off-ns = <50>;
+ gpmc,we-off-ns = <30>;
+ gpmc,rd-cycle-ns = <75>;
+ gpmc,wr-cycle-ns = <75>;
+ gpmc,access-ns = <55>;
+ gpmc,wr-access-ns = <55>;
+ gpmc,wait-pin = <0>;
+ gpmc,wait-on-write = "true";
+ gpmc,wait-on-read = "true";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ ethernet@gpmc {
+ reg = <5 0 0xff>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet_pins ðernet_wkgpio_pins>;
+
+ /* Either GPIO 103 or GPIO 121. Use 121 to match the reference design */
+ interrupt-parent = <&gpio4>;
+ interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
diff --git a/arch/arm/boot/dts/omap4-phytec-pcm-959.dts b/arch/arm/boot/dts/omap4-phytec-pcm-959.dts
new file mode 100644
index 000000000000..03196e657161
--- /dev/null
+++ b/arch/arm/boot/dts/omap4-phytec-pcm-959.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 Innovative Advantage, Inc.
+ */
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include "omap4460.dtsi"
+#include "omap4-phytec-pcm-049.dtsi"
+
+/ {
+ model = "Phytec PCM-959 Eval Board";
+ compatible = "phytec,pcm959", "phytec,pcm049", "ti,omap4460", "ti,omap4430", "ti,omap4";
+};
+
+&i2c4 {
+ status = "okay";
+
+ leddim: led@62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+
+ led-1 {
+ color = <LED_COLOR_ID_RED>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_YELLOW>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_YELLOW>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led-4 {
+ color = <LED_COLOR_ID_GREEN>;
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+ };
+};
--
2.25.1
On Wed, Feb 08, 2023 at 06:55:24PM -0800, Colin Foster wrote:
> Add documentation for additional OMAP SOMs and development platforms,
> provided by Phytec as the PCM-049 SOM and the PCM-959 development kit.
>
> Signed-off-by: Colin Foster <[email protected]>
> Acked-by: Krzysztof Kozlowski <[email protected]>
> ---
>
> v2->v3
> * Add Krzysztof Acked
>
> v1->v2
> * New patch
>
> ---
> Documentation/devicetree/bindings/arm/omap/omap.txt | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index fa8b31660cad..0a28215dfa12 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -131,6 +131,9 @@ Boards (incomplete list of examples):
> - OMAP4 PandaBoard : Low cost community board
> compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"
>
> +- OMAP4 PCM-959 : Commercial dev kit with PCM-049 SOM
> + compatible = "phytec,pcm959", "phytec,pcm049", "ti,omap4460", "ti,omap4430", "ti,omap4";
OMAP maintainers, if no one is going to convert all of omap.txt over to
schema, can we at least start an empty schema and add to it instead of
here...
Rob
* Rob Herring <[email protected]> [230209 19:35]:
> On Wed, Feb 08, 2023 at 06:55:24PM -0800, Colin Foster wrote:
> > --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> > +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> > @@ -131,6 +131,9 @@ Boards (incomplete list of examples):
> > - OMAP4 PandaBoard : Low cost community board
> > compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"
> >
> > +- OMAP4 PCM-959 : Commercial dev kit with PCM-049 SOM
> > + compatible = "phytec,pcm959", "phytec,pcm049", "ti,omap4460", "ti,omap4430", "ti,omap4";
Do you have both "ti,omap4460" and "ti,omap4430" SoCs variants for
these boards? If not just drop the SoC variant not in use. If you do have,
please mention it in the commit message.
> OMAP maintainers, if no one is going to convert all of omap.txt over to
> schema, can we at least start an empty schema and add to it instead of
> here...
That sounds like a good plan to me as it allows moving one device at a
time.
Colin, care to add the initial yaml binding file with your board?
Regards,
Tony
Hi Tony,
On Wed, Feb 15, 2023 at 09:14:43AM +0200, Tony Lindgren wrote:
> * Rob Herring <[email protected]> [230209 19:35]:
> > On Wed, Feb 08, 2023 at 06:55:24PM -0800, Colin Foster wrote:
> > > --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> > > +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> > > @@ -131,6 +131,9 @@ Boards (incomplete list of examples):
> > > - OMAP4 PandaBoard : Low cost community board
> > > compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"
> > >
> > > +- OMAP4 PCM-959 : Commercial dev kit with PCM-049 SOM
> > > + compatible = "phytec,pcm959", "phytec,pcm049", "ti,omap4460", "ti,omap4430", "ti,omap4";
>
> Do you have both "ti,omap4460" and "ti,omap4430" SoCs variants for
> these boards? If not just drop the SoC variant not in use. If you do have,
> please mention it in the commit message.
I don't, no. It might not be an issue anymore, but I remember there was
some reason I thought it had to be there. That was back when I was
struggling to get anything booting, so it might have been a false
positive.
I'll remove it, or at the very least explain why it needs to be there in
the next version.
>
> > OMAP maintainers, if no one is going to convert all of omap.txt over to
> > schema, can we at least start an empty schema and add to it instead of
> > here...
>
> That sounds like a good plan to me as it allows moving one device at a
> time.
>
> Colin, care to add the initial yaml binding file with your board?
I'll give it a go. To be clear, this would be
Documentation/devicetree/bindings/arm/omap.yaml and it would
include my device? I'm taking
Documentation/devicetree/bindings/arm/sunxi.yaml as inspiration (for no
reason other than it was the first one that I came across that seemed to
solve this same issue)
>
> Regards,
>
> Tony
* Colin Foster <[email protected]> [230215 16:46]:
> On Wed, Feb 15, 2023 at 09:14:43AM +0200, Tony Lindgren wrote:
> > * Rob Herring <[email protected]> [230209 19:35]:
> > > OMAP maintainers, if no one is going to convert all of omap.txt over to
> > > schema, can we at least start an empty schema and add to it instead of
> > > here...
> >
> > That sounds like a good plan to me as it allows moving one device at a
> > time.
> >
> > Colin, care to add the initial yaml binding file with your board?
>
> I'll give it a go. To be clear, this would be
> Documentation/devicetree/bindings/arm/omap.yaml and it would
> include my device? I'm taking
> Documentation/devicetree/bindings/arm/sunxi.yaml as inspiration (for no
> reason other than it was the first one that I came across that seemed to
> solve this same issue)
Yes just something minimal to start with.
Thanks,
Tony