Hello,
This series adds the device-tree nodes for CPSW5G instance of CPSW
Ethernet Switch on TI's J7200 SoC. Additionally, an overlay file is also
added to enable CPSW5G nodes in QSGMII mode with the Add-On J7 QUAD Port
Ethernet expansion QSGMII daughtercard.
Siddharth Vadapalli (2):
arm64: dts: ti: j7200-main: Add CPSW5G nodes
arm64: dts: ti: k3-j7200: Add overlay to enable CPSW5G ports in QSGMII
mode
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 83 +++++++++++++++
.../dts/ti/k3-j7200-quad-port-eth-exp.dtso | 100 ++++++++++++++++++
3 files changed, 185 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-quad-port-eth-exp.dtso
--
2.25.1
The J7 Quad Port Add-On Ethernet Card for J7200 Common-Proc-Board supports
QSGMII mode. Use the overlay to configure CPSW5G ports in QSGMII mode.
Add support to reset the PHY from kernel by using gpio-hog and gpio-reset.
Add aliases for CPSW5G ports to enable kernel to fetch MAC addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <[email protected]>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
.../dts/ti/k3-j7200-quad-port-eth-exp.dtso | 100 ++++++++++++++++++
2 files changed, 102 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-quad-port-eth-exp.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 167bcd9b09b7..04e95377a72a 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -45,7 +45,9 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
# Enable support for device-tree overlays
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+DTC_FLAGS_k3-j7200-common-proc-board += -@
DTC_FLAGS_k3-j721e-common-proc-board += -@
# Device-tree overlays
+dtb-$(CONFIG_ARCH_K3) += k3-j7200-quad-port-eth-exp.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j721e-quad-port-eth-exp.dtbo
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-quad-port-eth-exp.dtso b/arch/arm64/boot/dts/ti/k3-j7200-quad-port-eth-exp.dtso
new file mode 100644
index 000000000000..b84f185c0a31
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j7200-quad-port-eth-exp.dtso
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT Overlay for CPSW5G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
+ * J7200 board.
+ *
+ * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mux/ti-serdes.h>
+#include <dt-bindings/pinctrl/k3.h>
+
+/ {
+ fragment@101 {
+ target-path = "/";
+ __overlay__ {
+ aliases {
+ ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
+ ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
+ ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@3";
+ ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@4";
+ };
+ };
+ };
+};
+
+&cpsw0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio0_pins_default>;
+};
+
+&cpsw0_port1 {
+ phy-handle = <&cpsw5g_phy0>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 1>;
+};
+
+&cpsw0_port2 {
+ phy-handle = <&cpsw5g_phy1>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 2>;
+};
+
+&cpsw0_port3 {
+ phy-handle = <&cpsw5g_phy2>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 3>;
+};
+
+&cpsw0_port4 {
+ phy-handle = <&cpsw5g_phy3>;
+ phy-mode = "qsgmii";
+ mac-address = [00 00 00 00 00 00];
+ phys = <&cpsw0_phy_gmii_sel 4>;
+};
+
+&cpsw5g_mdio {
+ reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
+ reset-post-delay-us = <120000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw5g_phy0: ethernet-phy@16 {
+ reg = <16>;
+ };
+ cpsw5g_phy1: ethernet-phy@17 {
+ reg = <17>;
+ };
+ cpsw5g_phy2: ethernet-phy@18 {
+ reg = <18>;
+ };
+ cpsw5g_phy3: ethernet-phy@19 {
+ reg = <19>;
+ };
+};
+
+&exp2 {
+ qsgmii-line-hog {
+ gpio-hog;
+ gpios = <16 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "qsgmii-pwrdn-line";
+ };
+};
+
+&main_pmx0 {
+ mdio0_pins_default: mdio0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x00a8, PIN_OUTPUT, 5) /* (W19) UART8_TXD.MDIO0_MDC */
+ J721E_IOPAD(0x00a4, PIN_INPUT, 5) /* (W14) UART8_RXD.MDIO0_MDIO */
+ >;
+ };
+};
--
2.25.1
TI's J7200 SoC has a 5 port Ethernet Switch instance with 4 external
ports and 1 host port, referred to as CPSW5G.
Add device-tree nodes for CPSW5G and disable it by default. Device-tree
overlays will be used to enable it.
Signed-off-by: Siddharth Vadapalli <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 83 +++++++++++++++++++++++
1 file changed, 83 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 138381f43ce4..e9d42ae4ed09 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -39,6 +39,13 @@ serdes_ln_ctrl: mux-controller@4080 {
<0x4088 0x3>, <0x408c 0x3>; /* SERDES0 lane2/3 select */
};
+ cpsw0_phy_gmii_sel: phy@4044 {
+ compatible = "ti,j7200-cpsw5g-phy-gmii-sel";
+ ti,qsgmii-main-ports = <1>;
+ reg = <0x4044 0x10>;
+ #phy-cells = <1>;
+ };
+
usb_serdes_mux: mux-controller@4000 {
compatible = "mmio-mux";
#mux-control-cells = <1>;
@@ -304,6 +311,82 @@ cpts@310d0000 {
};
};
+ cpsw0: ethernet@c000000 {
+ compatible = "ti,j7200-cpswxg-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x00 0xc000000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0xc000000 0x00 0x200000>;
+ clocks = <&k3_clks 19 33>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 19 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xca00>,
+ <&main_udmap 0xca01>,
+ <&main_udmap 0xca02>,
+ <&main_udmap 0xca03>,
+ <&main_udmap 0xca04>,
+ <&main_udmap 0xca05>,
+ <&main_udmap 0xca06>,
+ <&main_udmap 0xca07>,
+ <&main_udmap 0x4a00>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpsw0_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ };
+
+ cpsw0_port2: port@2 {
+ reg = <2>;
+ ti,mac-only;
+ label = "port2";
+ };
+
+ cpsw0_port3: port@3 {
+ reg = <3>;
+ ti,mac-only;
+ label = "port3";
+ };
+
+ cpsw0_port4: port@4 {
+ reg = <4>;
+ ti,mac-only;
+ label = "port4";
+ };
+ };
+
+ cpsw5g_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 19 33>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 19 16>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
main_pmx0: pinctrl@11c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
--
2.25.1
Hello,
This series depends on the series at:
https://lore.kernel.org/r/[email protected]
and will cause merge conflict if merged before it.
Regards,
Siddharth.
On 10/03/23 15:44, Siddharth Vadapalli wrote:
> Hello,
>
> This series adds the device-tree nodes for CPSW5G instance of CPSW
> Ethernet Switch on TI's J7200 SoC. Additionally, an overlay file is also
> added to enable CPSW5G nodes in QSGMII mode with the Add-On J7 QUAD Port
> Ethernet expansion QSGMII daughtercard.
>
> Siddharth Vadapalli (2):
> arm64: dts: ti: j7200-main: Add CPSW5G nodes
> arm64: dts: ti: k3-j7200: Add overlay to enable CPSW5G ports in QSGMII
> mode
>
> arch/arm64/boot/dts/ti/Makefile | 2 +
> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 83 +++++++++++++++
> .../dts/ti/k3-j7200-quad-port-eth-exp.dtso | 100 ++++++++++++++++++
> 3 files changed, 185 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-quad-port-eth-exp.dtso
>