A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
and Audio. The audio clock controller is different from others, but the
rest are very similar from a functional and regmap point of view.
This patch series add support for Amlogic A1 PLL and Peripherals clock
drivers.
It blocks all A1 peripherals mainline support and a couple of patch series,
which were already reviewed and acked, but weren't merged due to pending
clock controller drivers series, e.g.
https://lore.kernel.org/linux-amlogic/[email protected]/
TODO: CPU and Audio clock controllers are not included in this patch
series, it will be sent later. The following clks from these controllers
are not supported for now:
* Audio clks - vad, mclk_vad, mclk_d, resample_a, locker_in, mclk_b,
pdmdclk, pdmsysclk, eqdrc, spdifin, mclk_a, audio2_toaudiotop,
audio2_tovad, audio2_toddr_vad, audio2_tdmin_vad, audio2_pdm,
audio2_ddr_arb, audio_audiolocker, audio_eqdrc, audio_resamplea,
audio_spdifin, audio_toddrb, audio_toddra, audio_frddrb, audio_frddra,
audio_tdmoutb, audio_tdmouta, audio_loopbacka, audio_tdminlb,
audio_tdminb, audio_tdmina, audio_ddr_arb, mclk_c
* CPU clks: cpu_fixed_source_sel0, cpu_fixed_source_div0,
cpu_fixed_source_sel1, cpu_fixed_source_div1, cpu_clk
Validation:
* to double check all clk flags run below helper script:
pushd /sys/kernel/debug/clk
for f in *; do
if [[ -f "$f/clk_flags" ]]; then
flags="$(cat $f/clk_flags | awk '{$1=$1};1' | sed ':a;N;$!ba;s/\n/ | /g')"
echo -e "$f: $flags"
fi
done
popd
* to trace current clks state use '/sys/kernel/debug/clk/clk_dump' node
with jq post-processing:
$ cat /sys/kernel/debug/clk/clk_dump | jq '.' > clk_dump.json
* to debug clk rate propagation, compile kernel with the following
definition:
$ sed -i "s/undef CLOCK_ALLOW_WRITE_DEBUGFS/define CLOCK_ALLOW_WRITE_DEBUGFS/g" drivers/clk/clk.c
after that, clk_rate debug node for each clock will be available for
write operation
Changes v10 since v9 at [10]:
- split general clk-pll changes into two different patchsets:
optional rst usage and new power sequence
- squash dt bindings patchsets to avoid chicken-or-the-egg problem
during run dt binding check routines
- add vendor prefix to PLL and Peripherals clkcs bindings filenames
- clear managed hifi_pll fields from initial poke table
- move DSPA_SEL, DSPB_SEL and SARADC_SEL to private clkid table,
because it should not be opened for direct usage
- pwm_a clk used for voltage regulation is not critical anymore, it
must be included to the proper cpu voltage regulation setup (will
be available in the next patch series)
- as discussed with Jerome, dspX clks are simple clocks and it
should be enabled/disabled/ignored/anything else from appropriate
DSP driver, so remove CLK_IGNORE_UNUSED tags
- provide more understandable comments and remove irrelevant (I hope so)
- remove CONFIG_OF usage, because it's redundant
- fix license issue, it's GPL-2.0+ only in the current version
- some commit msgs rewording
Changes v9 since v8 at [9]:
- remove common a1-clkc driver for the first version of a1 clock
controllers as Jerome suggested (it will be discussed after s4 and
a1 clks landed, hope so)
- replace inherited a1-pll clk_pll_ops with common ops and
introduce custom A1 PLL logic under MESON_PARM_APPLICABLE()
conditions
- rename xtal depended clocks in PLL and Peripherals domains
- remove 'a1_' prefix for all clocks, because they are already
inside A1 driver, it's redundant
- change udelay() to usleep_range() as preferred for small msec
amount
- purge all double quotes from the yaml schemas
- use proper dt node names following kernel guidelines
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
- use devm_platform_ioremap_resource() instead of simple
devm_ioremap_resource()
- mark all dspX clocks as CLK_IGNORE_UNUSED, because we do not want
to touch these clocks during CCF initialization due to possible
workload execution on it started from bootloader; in this case
bootloader already made all initialization stuff for dspX
- also mark all dspX with NO_REPARENT tag, because from dspX clocks
we want to select proper clk source from device tree
Changes v8 since v7 at [8]:
- introduced a1-clkc common driver for all A1 clock controllers
- exported meson_clk_pll_wait_lock symbol
- supported meson-a1-clkc common driver in the a1-pll and a1 clkc
- inherited a1-pll from the base clk-pll driver, implemented own
version of init/enable/disable/enabled routines; rate calculating
logic is fully the same
- aligned CLKID-related definitions with CLKID list from order
perspective to remove holes and permutations
- corrected Kconfig dependencies and types
- provided correct MODULE_AUTHORs()
- optimized and fixed up some clock relationships
- removed unused register offset definitions
- fixed up A1 PLL and Peripherals clkc dtb_check errors
- fixed clk_summary kernel panic due to missing a1_pad_ctrl
clk_regmap definition
- included PLL and Peripherals clk controllers to the base a1 dts
- The previous v7 version [8] had several logic and style problems,
all of them are resolved in this version. Original Jian Hu v7 patches
are not touched, and all additional fixes are implemented in separate
patches. Patch "clk: meson: add support for A1 PLL clock ops" is
removed, because a1-pll clk driver inherits all stuff from clk-pll
base driver, just implements custom init/enable/disable/is_enabled
callbacks.
Changes v7 since v6 at [7]:
- fix 'dt_binding_check' compiling error
- add acked-by
Changes v6 since v5 at [6]:
- fix yaml file
- add rst/current_en/l_detect parm detection
- remove 'meson_eeclkc_data' in a1.c and a1-pll.c
Changes v5 since v4 at [5]:
- change yaml GPL
- drop meson-eeclk.c patch, add probe function in each driver
- add CLK_IS_CRITICAL for sys_clk clock, drop the flag for sys_a
and sys_b
- add new parm for pll, add protection for rst parm
- drop flag for a1_fixed_pll
- remove the same comment for fclk_div, add "refer to"
- add critical flag for a1_sys_clk
- remove rtc table
- rename a1_dspa_en_dspa and a1_dspb_en_dspb
- remove useless comment
Changes v4 since v3 at [3]:
- fix reparenting orphan failed, it depends on jerome's patch [4]
- fix changelist in v3 about reparenting orphan
- remove the dts patch
Changes v3 since v2 at [2]:
- add probe function for A1
- separate the clock driver into two patch
- change some clock flags and ops
- add support for a1 PLL ops
- add A1 clock node
- fix reparenting orphan clock failed, registering xtal_fixpll
and xtal_hifipll after the provider registration, it is not
a best way.
Changes v2 since v1 at [1]:
- place A1 config alphabetically
- add actual reason for RO ops, CLK_IS_CRITICAL, CLK_IGNORE_UNUSED
- separate the driver into two driver: peripheral and pll driver
- delete CLK_IGNORE_UNUSED flag for pwm b/c/d/e/f clock, dsp clock
- delete the change in Kconfig.platforms, address to Kevin alone
- remove the useless comments
- modify the meson pll driver to support A1 PLLs
[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]
[4] https://lkml.kernel.org/r/[email protected]
[5] https://lkml.kernel.org/r/[email protected]
[6] https://lkml.kernel.org/r/[email protected]
[7] https://lkml.kernel.org/r/[email protected]
[8] https://lore.kernel.org/linux-amlogic/[email protected]/
[9] https://lore.kernel.org/linux-amlogic/[email protected]/
[10] https://lore.kernel.org/all/[email protected]/
Dmitry Rokosov (5):
clk: meson: make pll rst bit as optional
clk: meson: introduce new pll power-on sequence for A1 SoC family
dt-bindings: clock: meson: add A1 PLL and Peripherals clkcs bindings
clk: meson: a1: add Amlogic A1 PLL clock controller driver
clk: meson: a1: add Amlogic A1 Peripherals clock controller driver
.../bindings/clock/amlogic,a1-clkc.yaml | 73 +
.../bindings/clock/amlogic,a1-pll-clkc.yaml | 59 +
MAINTAINERS | 1 +
drivers/clk/meson/Kconfig | 20 +
drivers/clk/meson/Makefile | 2 +
drivers/clk/meson/a1-pll.c | 356 +++
drivers/clk/meson/a1-pll.h | 47 +
drivers/clk/meson/a1.c | 2242 +++++++++++++++++
drivers/clk/meson/a1.h | 118 +
drivers/clk/meson/clk-pll.c | 47 +-
drivers/clk/meson/clk-pll.h | 2 +
include/dt-bindings/clock/amlogic,a1-clkc.h | 100 +
.../dt-bindings/clock/amlogic,a1-pll-clkc.h | 20 +
13 files changed, 3080 insertions(+), 7 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-clkc.yaml
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml
create mode 100644 drivers/clk/meson/a1-pll.c
create mode 100644 drivers/clk/meson/a1-pll.h
create mode 100644 drivers/clk/meson/a1.c
create mode 100644 drivers/clk/meson/a1.h
create mode 100644 include/dt-bindings/clock/amlogic,a1-clkc.h
create mode 100644 include/dt-bindings/clock/amlogic,a1-pll-clkc.h
--
2.36.0