LinuxLists.cc - Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000

2023-02-03 17:47:26

Subject: Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000

On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
> The GL-MV1000 (Brume) is a small form-factor gateway router.
> It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
>
> Signed-off-by: Enrico Mioso <[email protected]>
> CC: Pali <[email protected]>

Looks good,

Reviewed-by: Pali Rohár <[email protected]>

> ---
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> .../dts/marvell/armada-3720-gl-mv1000.dts | 239 ++++++++++++++++++
> 2 files changed, 240 insertions(+)
> create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 058237681fe5..79ac09b58a89 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> new file mode 100644
> index 000000000000..b1b45b4fa9d4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> @@ -0,0 +1,239 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "armada-372x.dtsi"
> +
> +/ {
> + model = "GL.iNet GL-MV1000";
> + compatible = "glinet,gl-mv1000", "marvell,armada3720";
> +
> + aliases {
> + led-boot = &led_power;
> + led-failsafe = &led_power;
> + led-running = &led_power;
> + led-upgrade = &led_power;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> + };
> +
> + vcc_sd_reg1: regulator {
> + compatible = "regulator-gpio";
> + regulator-name = "vcc_sd1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> +
> + gpios-states = <0>;
> + states = <1800000 0x1
> + 3300000 0x0>;
> + enable-active-high;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + switch {
> + label = "switch";
> + linux,code = <BTN_0>;
> + gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + vpn {
> + label = "green:vpn";
> + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + wan {
> + label = "green:wan";
> + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_power: power {
> + label = "green:power";
> + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> + default-state = "on";
> + };
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + flash@0 {
> + reg = <0>;
> + compatible = "jedec,spi-nor";
> + spi-max-frequency = <104000000>;
> + m25p,fast-read;
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "firmware";
> + reg = <0 0xf0000>;
> + };
> +
> + partition@f0000 {
> + label = "u-boot-env";
> + reg = <0xf0000 0x8000>;
> + };
> +
> + factory: partition@f8000 {
> + label = "factory";
> + reg = <0xf8000 0x8000>;
> + read-only;
> + };
> +
> + partition@100000 {
> + label = "dtb";
> + reg = <0x100000 0x10000>;
> + read-only;
> + };
> +
> + partition@110000 {
> + label = "rescue";
> + reg = <0x110000 0x1000000>;
> + };
> + };
> + };
> +};
> +
> +&sdhci1 {
> + wp-inverted;
> + bus-width = <4>;
> + cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
> + marvell,pad-type = "sd";
> + no-1-8-v;
> + vqmmc-supply = <&vcc_sd_reg1>;
> + status = "okay";
> +};
> +
> +&sdhci0 {
> + bus-width = <8>;
> + mmc-ddr-1_8v;
> + mmc-hs400-1_8v;
> + non-removable;
> + no-sd;
> + no-sdio;
> + marvell,pad-type = "fixed-1-8v";
> + status = "okay";
> +};
> +
> +&usb3 {
> + status = "okay";
> +};
> +
> +&usb2 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&mdio {
> + switch0: switch0@1 {
> + compatible = "marvell,mv88e6085";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + dsa,member = <0 0>;
> +
> + ports: ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + label = "cpu";
> + ethernet = <&eth0>;
> + };
> +
> + port@1 {
> + reg = <1>;
> + label = "wan";
> + phy-handle = <&switch0phy0>;
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "lan0";
> + phy-handle = <&switch0phy1>;
> +
> + nvmem-cells = <&macaddr_factory_6>;
> + nvmem-cell-names = "mac-address";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "lan1";
> + phy-handle = <&switch0phy2>;
> +
> + nvmem-cells = <&macaddr_factory_6>;
> + nvmem-cell-names = "mac-address";
> + };
> + };
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch0phy0: switch0phy0@11 {
> + reg = <0x11>;
> + };
> + switch0phy1: switch0phy1@12 {
> + reg = <0x12>;
> + };
> + switch0phy2: switch0phy2@13 {
> + reg = <0x13>;
> + };
> + };
> + };
> +};
> +
> +&eth0 {
> + nvmem-cells = <&macaddr_factory_0>;
> + nvmem-cell-names = "mac-address";
> + phy-mode = "rgmii-id";
> + status = "okay";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&factory {
> + compatible = "nvmem-cells";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + macaddr_factory_0: macaddr@0 {
> + reg = <0x0 0x6>;
> + };
> +
> + macaddr_factory_6: macaddr@6 {
> + reg = <0x6 0x6>;
> + };
> +};
> --
> 2.39.1
>

2023-03-29 19:43:20

by Pali Rohár

[permalink] [raw]

Subject: Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000

PING?

On Friday 03 February 2023 18:46:18 Pali Rohár wrote:
> On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
> > The GL-MV1000 (Brume) is a small form-factor gateway router.
> > It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
> >
> > Signed-off-by: Enrico Mioso <[email protected]>
> > CC: Pali <[email protected]>
>
> Looks good,
>
> Reviewed-by: Pali Rohár <[email protected]>
>
> > ---
> > arch/arm64/boot/dts/marvell/Makefile | 1 +
> > .../dts/marvell/armada-3720-gl-mv1000.dts | 239 ++++++++++++++++++
> > 2 files changed, 240 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> >
> > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> > index 058237681fe5..79ac09b58a89 100644
> > --- a/arch/arm64/boot/dts/marvell/Makefile
> > +++ b/arch/arm64/boot/dts/marvell/Makefile
> > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> > +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
> > dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> > diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > new file mode 100644
> > index 000000000000..b1b45b4fa9d4
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > @@ -0,0 +1,239 @@
> > +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include "armada-372x.dtsi"
> > +
> > +/ {
> > + model = "GL.iNet GL-MV1000";
> > + compatible = "glinet,gl-mv1000", "marvell,armada3720";
> > +
> > + aliases {
> > + led-boot = &led_power;
> > + led-failsafe = &led_power;
> > + led-running = &led_power;
> > + led-upgrade = &led_power;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + memory@0 {
> > + device_type = "memory";
> > + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> > + };
> > +
> > + vcc_sd_reg1: regulator {
> > + compatible = "regulator-gpio";
> > + regulator-name = "vcc_sd1";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > +
> > + gpios-states = <0>;
> > + states = <1800000 0x1
> > + 3300000 0x0>;
> > + enable-active-high;
> > + };
> > +
> > + keys {
> > + compatible = "gpio-keys";
> > +
> > + reset {
> > + label = "reset";
> > + linux,code = <KEY_RESTART>;
> > + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + switch {
> > + label = "switch";
> > + linux,code = <BTN_0>;
> > + gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + vpn {
> > + label = "green:vpn";
> > + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + wan {
> > + label = "green:wan";
> > + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + led_power: power {
> > + label = "green:power";
> > + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> > + default-state = "on";
> > + };
> > + };
> > +};
> > +
> > +&spi0 {
> > + status = "okay";
> > +
> > + flash@0 {
> > + reg = <0>;
> > + compatible = "jedec,spi-nor";
> > + spi-max-frequency = <104000000>;
> > + m25p,fast-read;
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition@0 {
> > + label = "firmware";
> > + reg = <0 0xf0000>;
> > + };
> > +
> > + partition@f0000 {
> > + label = "u-boot-env";
> > + reg = <0xf0000 0x8000>;
> > + };
> > +
> > + factory: partition@f8000 {
> > + label = "factory";
> > + reg = <0xf8000 0x8000>;
> > + read-only;
> > + };
> > +
> > + partition@100000 {
> > + label = "dtb";
> > + reg = <0x100000 0x10000>;
> > + read-only;
> > + };
> > +
> > + partition@110000 {
> > + label = "rescue";
> > + reg = <0x110000 0x1000000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&sdhci1 {
> > + wp-inverted;
> > + bus-width = <4>;
> > + cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
> > + marvell,pad-type = "sd";
> > + no-1-8-v;
> > + vqmmc-supply = <&vcc_sd_reg1>;
> > + status = "okay";
> > +};
> > +
> > +&sdhci0 {
> > + bus-width = <8>;
> > + mmc-ddr-1_8v;
> > + mmc-hs400-1_8v;
> > + non-removable;
> > + no-sd;
> > + no-sdio;
> > + marvell,pad-type = "fixed-1-8v";
> > + status = "okay";
> > +};
> > +
> > +&usb3 {
> > + status = "okay";
> > +};
> > +
> > +&usb2 {
> > + status = "okay";
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&mdio {
> > + switch0: switch0@1 {
> > + compatible = "marvell,mv88e6085";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <1>;
> > +
> > + dsa,member = <0 0>;
> > +
> > + ports: ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + label = "cpu";
> > + ethernet = <&eth0>;
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > + label = "wan";
> > + phy-handle = <&switch0phy0>;
> > + };
> > +
> > + port@2 {
> > + reg = <2>;
> > + label = "lan0";
> > + phy-handle = <&switch0phy1>;
> > +
> > + nvmem-cells = <&macaddr_factory_6>;
> > + nvmem-cell-names = "mac-address";
> > + };
> > +
> > + port@3 {
> > + reg = <3>;
> > + label = "lan1";
> > + phy-handle = <&switch0phy2>;
> > +
> > + nvmem-cells = <&macaddr_factory_6>;
> > + nvmem-cell-names = "mac-address";
> > + };
> > + };
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + switch0phy0: switch0phy0@11 {
> > + reg = <0x11>;
> > + };
> > + switch0phy1: switch0phy1@12 {
> > + reg = <0x12>;
> > + };
> > + switch0phy2: switch0phy2@13 {
> > + reg = <0x13>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&eth0 {
> > + nvmem-cells = <&macaddr_factory_0>;
> > + nvmem-cell-names = "mac-address";
> > + phy-mode = "rgmii-id";
> > + status = "okay";
> > +
> > + fixed-link {
> > + speed = <1000>;
> > + full-duplex;
> > + };
> > +};
> > +
> > +&factory {
> > + compatible = "nvmem-cells";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + macaddr_factory_0: macaddr@0 {
> > + reg = <0x0 0x6>;
> > + };
> > +
> > + macaddr_factory_6: macaddr@6 {
> > + reg = <0x6 0x6>;
> > + };
> > +};
> > --
> > 2.39.1
> >

2023-04-07 15:48:10

by Gregory CLEMENT

[permalink] [raw]

Subject: Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000

Pali Rohár <[email protected]> writes:

> On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
>> The GL-MV1000 (Brume) is a small form-factor gateway router.
>> It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
>>
>> Signed-off-by: Enrico Mioso <[email protected]>
>> CC: Pali <[email protected]>
>
> Looks good,
>
> Reviewed-by: Pali Rohár <[email protected]>

Applied on mvebu/dt64

Thanks,

Gregory

>
>> ---
>> arch/arm64/boot/dts/marvell/Makefile | 1 +
>> .../dts/marvell/armada-3720-gl-mv1000.dts | 239 ++++++++++++++++++
>> 2 files changed, 240 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>>
>> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
>> index 058237681fe5..79ac09b58a89 100644
>> --- a/arch/arm64/boot/dts/marvell/Makefile
>> +++ b/arch/arm64/boot/dts/marvell/Makefile
>> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
>> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
>> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> new file mode 100644
>> index 000000000000..b1b45b4fa9d4
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> @@ -0,0 +1,239 @@
>> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include "armada-372x.dtsi"
>> +
>> +/ {
>> + model = "GL.iNet GL-MV1000";
>> + compatible = "glinet,gl-mv1000", "marvell,armada3720";
>> +
>> + aliases {
>> + led-boot = &led_power;
>> + led-failsafe = &led_power;
>> + led-running = &led_power;
>> + led-upgrade = &led_power;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + memory@0 {
>> + device_type = "memory";
>> + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
>> + };
>> +
>> + vcc_sd_reg1: regulator {
>> + compatible = "regulator-gpio";
>> + regulator-name = "vcc_sd1";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> +
>> + gpios-states = <0>;
>> + states = <1800000 0x1
>> + 3300000 0x0>;
>> + enable-active-high;
>> + };
>> +
>> + keys {
>> + compatible = "gpio-keys";
>> +
>> + reset {
>> + label = "reset";
>> + linux,code = <KEY_RESTART>;
>> + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + switch {
>> + label = "switch";
>> + linux,code = <BTN_0>;
>> + gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + vpn {
>> + label = "green:vpn";
>> + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + wan {
>> + label = "green:wan";
>> + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + led_power: power {
>> + label = "green:power";
>> + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
>> + default-state = "on";
>> + };
>> + };
>> +};
>> +
>> +&spi0 {
>> + status = "okay";
>> +
>> + flash@0 {
>> + reg = <0>;
>> + compatible = "jedec,spi-nor";
>> + spi-max-frequency = <104000000>;
>> + m25p,fast-read;
>> + partitions {
>> + compatible = "fixed-partitions";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + partition@0 {
>> + label = "firmware";
>> + reg = <0 0xf0000>;
>> + };
>> +
>> + partition@f0000 {
>> + label = "u-boot-env";
>> + reg = <0xf0000 0x8000>;
>> + };
>> +
>> + factory: partition@f8000 {
>> + label = "factory";
>> + reg = <0xf8000 0x8000>;
>> + read-only;
>> + };
>> +
>> + partition@100000 {
>> + label = "dtb";
>> + reg = <0x100000 0x10000>;
>> + read-only;
>> + };
>> +
>> + partition@110000 {
>> + label = "rescue";
>> + reg = <0x110000 0x1000000>;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&sdhci1 {
>> + wp-inverted;
>> + bus-width = <4>;
>> + cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
>> + marvell,pad-type = "sd";
>> + no-1-8-v;
>> + vqmmc-supply = <&vcc_sd_reg1>;
>> + status = "okay";
>> +};
>> +
>> +&sdhci0 {
>> + bus-width = <8>;
>> + mmc-ddr-1_8v;
>> + mmc-hs400-1_8v;
>> + non-removable;
>> + no-sd;
>> + no-sdio;
>> + marvell,pad-type = "fixed-1-8v";
>> + status = "okay";
>> +};
>> +
>> +&usb3 {
>> + status = "okay";
>> +};
>> +
>> +&usb2 {
>> + status = "okay";
>> +};
>> +
>> +&uart0 {
>> + status = "okay";
>> +};
>> +
>> +&mdio {
>> + switch0: switch0@1 {
>> + compatible = "marvell,mv88e6085";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <1>;
>> +
>> + dsa,member = <0 0>;
>> +
>> + ports: ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> + label = "cpu";
>> + ethernet = <&eth0>;
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> + label = "wan";
>> + phy-handle = <&switch0phy0>;
>> + };
>> +
>> + port@2 {
>> + reg = <2>;
>> + label = "lan0";
>> + phy-handle = <&switch0phy1>;
>> +
>> + nvmem-cells = <&macaddr_factory_6>;
>> + nvmem-cell-names = "mac-address";
>> + };
>> +
>> + port@3 {
>> + reg = <3>;
>> + label = "lan1";
>> + phy-handle = <&switch0phy2>;
>> +
>> + nvmem-cells = <&macaddr_factory_6>;
>> + nvmem-cell-names = "mac-address";
>> + };
>> + };
>> +
>> + mdio {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + switch0phy0: switch0phy0@11 {
>> + reg = <0x11>;
>> + };
>> + switch0phy1: switch0phy1@12 {
>> + reg = <0x12>;
>> + };
>> + switch0phy2: switch0phy2@13 {
>> + reg = <0x13>;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&eth0 {
>> + nvmem-cells = <&macaddr_factory_0>;
>> + nvmem-cell-names = "mac-address";
>> + phy-mode = "rgmii-id";
>> + status = "okay";
>> +
>> + fixed-link {
>> + speed = <1000>;
>> + full-duplex;
>> + };
>> +};
>> +
>> +&factory {
>> + compatible = "nvmem-cells";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + macaddr_factory_0: macaddr@0 {
>> + reg = <0x0 0x6>;
>> + };
>> +
>> + macaddr_factory_6: macaddr@6 {
>> + reg = <0x6 0x6>;
>> + };
>> +};
>> --
>> 2.39.1
>>

--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com