A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
and Audio. The audio clock controller is different from others, but the
rest are very similar from a functional and regmap point of view.
This patch series add support for Amlogic A1 PLL and Peripherals clock
drivers.
It blocks all A1 peripherals mainline support and a couple of patch series,
which were already reviewed and acked, but weren't merged due to pending
clock controller drivers series, e.g.
https://lore.kernel.org/linux-amlogic/[email protected]/
TODO: CPU and Audio clock controllers are not included in this patch
series, it will be sent later. The following clks from these controllers
are not supported for now:
* Audio clks - vad, mclk_vad, mclk_d, resample_a, locker_in, mclk_b,
pdmdclk, pdmsysclk, eqdrc, spdifin, mclk_a, audio2_toaudiotop,
audio2_tovad, audio2_toddr_vad, audio2_tdmin_vad, audio2_pdm,
audio2_ddr_arb, audio_audiolocker, audio_eqdrc, audio_resamplea,
audio_spdifin, audio_toddrb, audio_toddra, audio_frddrb, audio_frddra,
audio_tdmoutb, audio_tdmouta, audio_loopbacka, audio_tdminlb,
audio_tdminb, audio_tdmina, audio_ddr_arb, mclk_c
* CPU clks: cpu_fixed_source_sel0, cpu_fixed_source_div0,
cpu_fixed_source_sel1, cpu_fixed_source_div1, cpu_clk
Validation:
* to double check all clk flags run below helper script:
pushd /sys/kernel/debug/clk
for f in *; do
if [[ -f "$f/clk_flags" ]]; then
flags="$(cat $f/clk_flags | awk '{$1=$1};1' | sed ':a;N;$!ba;s/\n/ | /g')"
echo -e "$f: $flags"
fi
done
popd
* to trace current clks state use '/sys/kernel/debug/clk/clk_dump' node
with jq post-processing:
$ cat /sys/kernel/debug/clk/clk_dump | jq '.' > clk_dump.json
* to debug clk rate propagation, compile kernel with the following
definition:
$ sed -i "s/undef CLOCK_ALLOW_WRITE_DEBUGFS/define CLOCK_ALLOW_WRITE_DEBUGFS/g" drivers/clk/clk.c
after that, clk_rate debug node for each clock will be available for
write operation
Changes v12 since v11 at [12]:
- split the DT bindings patchset into two patches: one for the PLL clock
controller driver, and one for the peripherals clock controller driver
- to satisfy the DT binding checker, use fake references to the
peripherals clock controller in the PLL DT bindings schema, and then
replace them with real references when the peripherals bindings
become available.
- remove the public/private clocks concept from both controllers,
and instead use a linear clkid list with both exposed and internal
objects, all of which are registered in the clock provider
- combine all comments about RTC children with the flag
'CLK_SET_RATE_NO_REPARENT' into a single item with multiple
references to it
Changes v11 since v10 at [11]:
- change include/dt-bindings license to proper value required for
bindings files: 'GPL-2.0-only OR BSD-2-Clause'
- pll and peripherals clocks are split into public and private parts;
public clocks are available for external consumers through the DT layer,
private clocks include internal muxes and dividers of composite clocks,
they are placed inside clock controller driver without external access
- make public clks CLKID bindings continuous
- mark the following clock muxes as NO_REPARENT and add them to
public clocks list: GEN_SEL, DSPA_A_SEL, DSPA_B_SEL, DSPB_A_SEL,
DSP_B_B_SEL, PWM_A_SEL, PWM_B_SEL, PWM_C_SEL, PWM_D_SEL,
PWM_E_SEL, PWM_F_SEL, CECA_32K_SEL, CECB_32K_SEL; each of them can
be inherited from more accurate RTC clock and sometimes it's
required to forbid reparenting in such situation; also GEN_SEL can
be connected to external PAD and should not change parent
automatically due to rate propagation. For such clocks user must
setup parents on the DT side
Changes v10 since v9 at [10]:
- split general clk-pll changes into two different patchsets:
optional rst usage and new power sequence
- squash dt bindings patchsets to avoid chicken-or-the-egg problem
during run dt binding check routines
- add vendor prefix to PLL and Peripherals clkcs bindings filenames
- clear managed hifi_pll fields from initial poke table
- move DSPA_SEL, DSPB_SEL and SARADC_SEL to private clkid table,
because it should not be opened for direct usage
- pwm_a clk used for voltage regulation is not critical anymore, it
must be included to the proper cpu voltage regulation setup (will
be available in the next patch series)
- as discussed with Jerome, dspX clks are simple clocks and it
should be enabled/disabled/ignored/anything else from appropriate
DSP driver, so remove CLK_IGNORE_UNUSED tags
- provide more understandable comments and remove irrelevant (I hope so)
- remove CONFIG_OF usage, because it's redundant
- fix license issue, it's GPL-2.0+ only in the current version
- some commit msgs rewording
Changes v9 since v8 at [9]:
- remove common a1-clkc driver for the first version of a1 clock
controllers as Jerome suggested (it will be discussed after s4 and
a1 clks landed, hope so)
- replace inherited a1-pll clk_pll_ops with common ops and
introduce custom A1 PLL logic under MESON_PARM_APPLICABLE()
conditions
- rename xtal depended clocks in PLL and Peripherals domains
- remove 'a1_' prefix for all clocks, because they are already
inside A1 driver, it's redundant
- change udelay() to usleep_range() as preferred for small msec
amount
- purge all double quotes from the yaml schemas
- use proper dt node names following kernel guidelines
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
- use devm_platform_ioremap_resource() instead of simple
devm_ioremap_resource()
- mark all dspX clocks as CLK_IGNORE_UNUSED, because we do not want
to touch these clocks during CCF initialization due to possible
workload execution on it started from bootloader; in this case
bootloader already made all initialization stuff for dspX
- also mark all dspX with NO_REPARENT tag, because from dspX clocks
we want to select proper clk source from device tree
Changes v8 since v7 at [8]:
- introduced a1-clkc common driver for all A1 clock controllers
- exported meson_clk_pll_wait_lock symbol
- supported meson-a1-clkc common driver in the a1-pll and a1 clkc
- inherited a1-pll from the base clk-pll driver, implemented own
version of init/enable/disable/enabled routines; rate calculating
logic is fully the same
- aligned CLKID-related definitions with CLKID list from order
perspective to remove holes and permutations
- corrected Kconfig dependencies and types
- provided correct MODULE_AUTHORs()
- optimized and fixed up some clock relationships
- removed unused register offset definitions
- fixed up A1 PLL and Peripherals clkc dtb_check errors
- fixed clk_summary kernel panic due to missing a1_pad_ctrl
clk_regmap definition
- included PLL and Peripherals clk controllers to the base a1 dts
- The previous v7 version [8] had several logic and style problems,
all of them are resolved in this version. Original Jian Hu v7 patches
are not touched, and all additional fixes are implemented in separate
patches. Patch "clk: meson: add support for A1 PLL clock ops" is
removed, because a1-pll clk driver inherits all stuff from clk-pll
base driver, just implements custom init/enable/disable/is_enabled
callbacks.
Changes v7 since v6 at [7]:
- fix 'dt_binding_check' compiling error
- add acked-by
Changes v6 since v5 at [6]:
- fix yaml file
- add rst/current_en/l_detect parm detection
- remove 'meson_eeclkc_data' in a1.c and a1-pll.c
Changes v5 since v4 at [5]:
- change yaml GPL
- drop meson-eeclk.c patch, add probe function in each driver
- add CLK_IS_CRITICAL for sys_clk clock, drop the flag for sys_a
and sys_b
- add new parm for pll, add protection for rst parm
- drop flag for a1_fixed_pll
- remove the same comment for fclk_div, add "refer to"
- add critical flag for a1_sys_clk
- remove rtc table
- rename a1_dspa_en_dspa and a1_dspb_en_dspb
- remove useless comment
Changes v4 since v3 at [3]:
- fix reparenting orphan failed, it depends on jerome's patch [4]
- fix changelist in v3 about reparenting orphan
- remove the dts patch
Changes v3 since v2 at [2]:
- add probe function for A1
- separate the clock driver into two patch
- change some clock flags and ops
- add support for a1 PLL ops
- add A1 clock node
- fix reparenting orphan clock failed, registering xtal_fixpll
and xtal_hifipll after the provider registration, it is not
a best way.
Changes v2 since v1 at [1]:
- place A1 config alphabetically
- add actual reason for RO ops, CLK_IS_CRITICAL, CLK_IGNORE_UNUSED
- separate the driver into two driver: peripheral and pll driver
- delete CLK_IGNORE_UNUSED flag for pwm b/c/d/e/f clock, dsp clock
- delete the change in Kconfig.platforms, address to Kevin alone
- remove the useless comments
- modify the meson pll driver to support A1 PLLs
Links:
[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]
[4] https://lkml.kernel.org/r/[email protected]
[5] https://lkml.kernel.org/r/[email protected]
[6] https://lkml.kernel.org/r/[email protected]
[7] https://lkml.kernel.org/r/[email protected]
[8] https://lore.kernel.org/linux-amlogic/[email protected]/
[9] https://lore.kernel.org/linux-amlogic/[email protected]/
[10] https://lore.kernel.org/all/[email protected]/
[11] https://lore.kernel.org/all/[email protected]/
[12] https://lore.kernel.org/all/[email protected]/
Dmitry Rokosov (6):
clk: meson: make pll rst bit as optional
clk: meson: introduce new pll power-on sequence for A1 SoC family
dt-bindings: clock: meson: add A1 PLL clock controller bindings
clk: meson: a1: add Amlogic A1 PLL clock controller driver
dt-bindings: clock: meson: add A1 Peripherals clock controller
bindings
clk: meson: a1: add Amlogic A1 Peripherals clock controller driver
.../bindings/clock/amlogic,a1-clkc.yaml | 73 +
.../bindings/clock/amlogic,a1-pll-clkc.yaml | 59 +
MAINTAINERS | 1 +
drivers/clk/meson/Kconfig | 20 +
drivers/clk/meson/Makefile | 2 +
drivers/clk/meson/a1-pll.c | 360 +++
drivers/clk/meson/a1-pll.h | 47 +
drivers/clk/meson/a1.c | 2277 +++++++++++++++++
drivers/clk/meson/a1.h | 114 +
drivers/clk/meson/clk-pll.c | 47 +-
drivers/clk/meson/clk-pll.h | 2 +
include/dt-bindings/clock/amlogic,a1-clkc.h | 114 +
.../dt-bindings/clock/amlogic,a1-pll-clkc.h | 20 +
13 files changed, 3129 insertions(+), 7 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-clkc.yaml
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml
create mode 100644 drivers/clk/meson/a1-pll.c
create mode 100644 drivers/clk/meson/a1-pll.h
create mode 100644 drivers/clk/meson/a1.c
create mode 100644 drivers/clk/meson/a1.h
create mode 100644 include/dt-bindings/clock/amlogic,a1-clkc.h
create mode 100644 include/dt-bindings/clock/amlogic,a1-pll-clkc.h
--
2.36.0
Introduce Peripherals clock controller for Amlogic A1 SoC family.
A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
and Audio.
This patchset adds support for Amlogic A1 Peripherals clock driver and
allows to generate clocks for all A1 SoC peripheral IPs.
Signed-off-by: Jian Hu <[email protected]>
Signed-off-by: Dmitry Rokosov <[email protected]>
---
drivers/clk/meson/Kconfig | 10 +
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/a1.c | 2277 ++++++++++++++++++++++++++++++++++++
drivers/clk/meson/a1.h | 114 ++
4 files changed, 2402 insertions(+)
create mode 100644 drivers/clk/meson/a1.c
create mode 100644 drivers/clk/meson/a1.h
diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index f56da2a4b000..970892b07043 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -109,6 +109,16 @@ config COMMON_CLK_A1_PLL
device, A1 SoC Family. Say Y if you want A1 PLL clock controller
to work.
+config COMMON_CLK_A1
+ tristate "Meson A1 SoC clock controller support"
+ depends on ARM64
+ select COMMON_CLK_MESON_DUALDIV
+ select COMMON_CLK_MESON_REGMAP
+ help
+ Support for the Peripherals clock controller on Amlogic A113L based
+ device, A1 SoC Family. Say Y if you want A1 Peripherals clock
+ controller to work.
+
config COMMON_CLK_G12A
tristate "G12 and SM1 SoC clock controllers support"
depends on ARM64
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 2f17f475a48f..0e6f293c05d4 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
+obj-$(CONFIG_COMMON_CLK_A1) += a1.o
obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
diff --git a/drivers/clk/meson/a1.c b/drivers/clk/meson/a1.c
new file mode 100644
index 000000000000..4caf07ce92cd
--- /dev/null
+++ b/drivers/clk/meson/a1.c
@@ -0,0 +1,2277 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "a1.h"
+#include "clk-dualdiv.h"
+#include "clk-regmap.h"
+
+static struct clk_regmap xtal_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_in",
+ .ops = &clk_regmap_gate_ro_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fixpll_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "fixpll_in",
+ .ops = &clk_regmap_gate_ro_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap usb_phy_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 2,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_phy_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap usb_ctrl_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 3,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_ctrl_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap hifipll_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 4,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "hifipll_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap syspll_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 5,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "syspll_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap dds_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 6,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dds_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap rtc_32k_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "rtc_32k_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static const struct meson_clk_dualdiv_param clk_32k_div_table[] = {
+ {
+ .dual = 1,
+ .n1 = 733,
+ .m1 = 8,
+ .n2 = 732,
+ .m2 = 11,
+ },
+ {}
+};
+
+static struct clk_regmap rtc_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = RTC_BY_OSCIN_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = RTC_BY_OSCIN_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = clk_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap rtc_32k_xtal = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL1,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "rtc_32k_xtal",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap rtc_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = RTC_CTRL,
+ .mask = 0x3,
+ .shift = 0,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_xtal.hw,
+ &rtc_32k_div.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/*
+ * All clocks that can be inherited from a more accurate RTC clock are marked
+ * with the CLK_SET_RATE_NO_REPARENT flag. This is because in certain
+ * situations, we may need to freeze their parent. The parent setup of these
+ * clocks should be located on the device tree side.
+ */
+struct clk_regmap rtc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static u32 mux_table_sys[] = { 0, 1, 2, 3, 7 };
+static const struct clk_parent_data sys_parents[] = {
+ { .fw_name = "xtal" },
+ { .fw_name = "fclk_div2" },
+ { .fw_name = "fclk_div3" },
+ { .fw_name = "fclk_div5" },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap sys_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_sys,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_b_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_data = sys_parents,
+ .num_parents = ARRAY_SIZE(sys_parents),
+ },
+};
+
+static struct clk_regmap sys_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SYS_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sys_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_sys,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_a_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_data = sys_parents,
+ .num_parents = ARRAY_SIZE(sys_parents),
+ },
+};
+
+static struct clk_regmap sys_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SYS_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sys_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 31,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_a.hw,
+ &sys_b.hw,
+ },
+ .num_parents = 2,
+ /*
+ * This clock is used by APB bus which is set in boot ROM code
+ * and is required by the platform to operate correctly.
+ * Until the following condition are met, we need this clock to
+ * be marked as critical:
+ * a) Mark the clock used by a firmware resource, if possible
+ * b) CCF has a clock hand-off mechanism to make the sure the
+ * clock stays on until the proper driver comes along
+ */
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+ },
+};
+
+static u32 mux_table_dsp_ab[] = { 0, 1, 2, 3, 4, 7 };
+static const struct clk_parent_data dsp_ab_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .fw_name = "fclk_div2", },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+ { .fw_name = "hifi_pll", },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap dspa_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspa_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPA_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspa_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPA_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_a.hw,
+ &dspa_b.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_en = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_EN,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_en",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_en_nic = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_EN,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_en_nic",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspb_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPB_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspb_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPB_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_a.hw,
+ &dspb_b.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_en = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_EN,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_en",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_en_nic = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_EN,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_en_nic",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap clk_24m = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "24m",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_fixed_factor clk_24m_div2 = {
+ .mult = 1,
+ .div = 2,
+ .hw.init = &(struct clk_init_data){
+ .name = "24m_div2",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &clk_24m.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap clk_12m = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 10,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "12m",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &clk_24m_div2.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div2_divn_pre = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = CLK12_24_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_divn_pre",
+ .ops = &clk_regmap_divider_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "fclk_div2",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div2_divn = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 12,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_divn",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fclk_div2_divn_pre.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/*
+ * the index 2 is sys_pll_div16, it will be implemented in the CPU clock driver,
+ * the index 4 is the clock measurement source, it's not supported yet
+ */
+static u32 gen_table[] = { 0, 1, 3, 5, 6, 7, 8 };
+static const struct clk_parent_data gen_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &rtc.hw },
+ { .fw_name = "hifi_pll", },
+ { .fw_name = "fclk_div2", },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+ { .fw_name = "fclk_div7", },
+};
+
+static struct clk_regmap gen_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = GEN_CLK_CTRL,
+ .mask = 0xf,
+ .shift = 12,
+ .table = gen_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "gen_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = gen_parent_data,
+ .num_parents = ARRAY_SIZE(gen_parent_data),
+ /*
+ * The GEN clock can be connected to an external pad, so it
+ * may be set up directly from the device tree. Additionally,
+ * the GEN clock can be inherited from a more accurate RTC
+ * clock, so in certain situations, it may be necessary
+ * to freeze its parent.
+ */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap gen_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = GEN_CLK_CTRL,
+ .shift = 0,
+ .width = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "gen_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &gen_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap gen = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = GEN_CLK_CTRL,
+ .bit_idx = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "gen",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &gen_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap saradc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "saradc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw, },
+ },
+ .num_parents = 2,
+ },
+};
+
+static struct clk_regmap saradc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "saradc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &saradc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap saradc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "saradc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &saradc_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data pwm_abcd_parents[] = {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap pwm_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .mask = 0x1,
+ .shift = 25,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .shift = 16,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_c_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_c_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_c_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_c_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_c_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_c = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_c",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_c_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_d_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .mask = 0x1,
+ .shift = 25,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_d_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_d_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .shift = 16,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_d_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_d_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_d = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_d",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_d_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data pwm_ef_parents[] = {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw },
+ { .fw_name = "fclk_div5", },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap pwm_e_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_e_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_ef_parents,
+ .num_parents = ARRAY_SIZE(pwm_ef_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_e_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_e_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_e_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_e = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_e",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_e_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_f_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .mask = 0x3,
+ .shift = 25,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_f_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_ef_parents,
+ .num_parents = ARRAY_SIZE(pwm_ef_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_f_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .shift = 16,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_f_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_f_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_f = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_f",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_f_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/*
+ * spicc clk
+ * fdiv2 |\ |\ _____
+ * ---------| |---DIV--| | | | spicc out
+ * ---------| | | |-----|GATE |---------
+ * ..... |/ | / |_____|
+ * --------------------|/
+ * 24M
+ */
+static const struct clk_parent_data spicc_spifc_parents[] = {
+ { .fw_name = "fclk_div2"},
+ { .fw_name = "fclk_div3"},
+ { .fw_name = "fclk_div5"},
+ { .fw_name = "hifi_pll" },
+};
+
+static struct clk_regmap spicc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPICC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spicc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = spicc_spifc_parents,
+ .num_parents = ARRAY_SIZE(spicc_spifc_parents),
+ },
+};
+
+static struct clk_regmap spicc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SPICC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spicc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spicc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spicc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPICC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spicc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &spicc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spicc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SPICC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "spicc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spicc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap ts_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = TS_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ts_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap ts = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = TS_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "ts",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ts_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spifc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPIFC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spifc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = spicc_spifc_parents,
+ .num_parents = ARRAY_SIZE(spicc_spifc_parents),
+ },
+};
+
+static struct clk_regmap spifc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SPIFC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spifc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spifc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spifc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPIFC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spifc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &spifc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spifc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SPIFC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "spifc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spifc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data usb_bus_parents[] = {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+};
+
+static struct clk_regmap usb_bus_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = USB_BUSCLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "usb_bus_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = usb_bus_parents,
+ .num_parents = ARRAY_SIZE(usb_bus_parents),
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap usb_bus_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = USB_BUSCLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "usb_bus_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &usb_bus_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap usb_bus = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = USB_BUSCLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_bus",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &usb_bus_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data sd_emmc_psram_dmc_parents[] = {
+ { .fw_name = "fclk_div2", },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+ { .fw_name = "hifi_pll", },
+};
+
+static struct clk_regmap sd_emmc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sd_emmc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = sd_emmc_psram_dmc_parents,
+ .num_parents = ARRAY_SIZE(sd_emmc_psram_dmc_parents),
+ },
+};
+
+static struct clk_regmap sd_emmc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sd_emmc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sd_emmc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sd_emmc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sd_emmc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &sd_emmc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sd_emmc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sd_emmc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sd_emmc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap psram_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PSRAM_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "psram_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = sd_emmc_psram_dmc_parents,
+ .num_parents = ARRAY_SIZE(sd_emmc_psram_dmc_parents),
+ },
+};
+
+static struct clk_regmap psram_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PSRAM_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "psram_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &psram_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap psram_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PSRAM_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "psram_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &psram_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap psram = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PSRAM_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "psram",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &psram_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dmc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DMC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = sd_emmc_psram_dmc_parents,
+ .num_parents = ARRAY_SIZE(sd_emmc_psram_dmc_parents),
+ },
+};
+
+static struct clk_regmap dmc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DMC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dmc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dmc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DMC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &dmc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dmc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DMC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dmc",
+ .ops = &clk_regmap_gate_ro_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dmc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap ceca_32k_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECA_CLK_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "ceca_32k_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap ceca_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = CECA_CLK_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = CECA_CLK_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = CECA_CLK_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = CECA_CLK_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = CECA_CLK_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = clk_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap ceca_32k_sel_pre = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECA_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 24,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_sel_pre",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_div.hw,
+ &ceca_32k_in.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap ceca_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECA_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 31,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_sel_pre.hw,
+ &rtc.hw,
+ },
+ .num_parents = 2,
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap ceca_32k_out = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECA_CLK_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_out",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cecb_32k_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECB_CLK_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cecb_32k_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap cecb_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = CECB_CLK_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = CECB_CLK_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = CECB_CLK_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = CECB_CLK_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = CECB_CLK_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = clk_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap cecb_32k_sel_pre = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECB_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 24,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_sel_pre",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_div.hw,
+ &cecb_32k_in.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cecb_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECB_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 31,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_sel_pre.hw,
+ &rtc.hw,
+ },
+ .num_parents = 2,
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap cecb_32k_out = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECB_CLK_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_out",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+#define MESON_GATE(_name, _reg, _bit) \
+ MESON_PCLK(_name, _reg, _bit, &sys.hw)
+
+static MESON_GATE(clktree, SYS_CLK_EN0, 0);
+static MESON_GATE(reset_ctrl, SYS_CLK_EN0, 1);
+static MESON_GATE(analog_ctrl, SYS_CLK_EN0, 2);
+static MESON_GATE(pwr_ctrl, SYS_CLK_EN0, 3);
+static MESON_GATE(pad_ctrl, SYS_CLK_EN0, 4);
+static MESON_GATE(sys_ctrl, SYS_CLK_EN0, 5);
+static MESON_GATE(temp_sensor, SYS_CLK_EN0, 6);
+static MESON_GATE(am2axi_dev, SYS_CLK_EN0, 7);
+static MESON_GATE(spicc_b, SYS_CLK_EN0, 8);
+static MESON_GATE(spicc_a, SYS_CLK_EN0, 9);
+static MESON_GATE(msr, SYS_CLK_EN0, 10);
+static MESON_GATE(audio, SYS_CLK_EN0, 11);
+static MESON_GATE(jtag_ctrl, SYS_CLK_EN0, 12);
+static MESON_GATE(saradc_en, SYS_CLK_EN0, 13);
+static MESON_GATE(pwm_ef, SYS_CLK_EN0, 14);
+static MESON_GATE(pwm_cd, SYS_CLK_EN0, 15);
+static MESON_GATE(pwm_ab, SYS_CLK_EN0, 16);
+static MESON_GATE(cec, SYS_CLK_EN0, 17);
+static MESON_GATE(i2c_s, SYS_CLK_EN0, 18);
+static MESON_GATE(ir_ctrl, SYS_CLK_EN0, 19);
+static MESON_GATE(i2c_m_d, SYS_CLK_EN0, 20);
+static MESON_GATE(i2c_m_c, SYS_CLK_EN0, 21);
+static MESON_GATE(i2c_m_b, SYS_CLK_EN0, 22);
+static MESON_GATE(i2c_m_a, SYS_CLK_EN0, 23);
+static MESON_GATE(acodec, SYS_CLK_EN0, 24);
+static MESON_GATE(otp, SYS_CLK_EN0, 25);
+static MESON_GATE(sd_emmc_a, SYS_CLK_EN0, 26);
+static MESON_GATE(usb_phy, SYS_CLK_EN0, 27);
+static MESON_GATE(usb_ctrl, SYS_CLK_EN0, 28);
+static MESON_GATE(sys_dspb, SYS_CLK_EN0, 29);
+static MESON_GATE(sys_dspa, SYS_CLK_EN0, 30);
+static MESON_GATE(dma, SYS_CLK_EN0, 31);
+static MESON_GATE(irq_ctrl, SYS_CLK_EN1, 0);
+static MESON_GATE(nic, SYS_CLK_EN1, 1);
+static MESON_GATE(gic, SYS_CLK_EN1, 2);
+static MESON_GATE(uart_c, SYS_CLK_EN1, 3);
+static MESON_GATE(uart_b, SYS_CLK_EN1, 4);
+static MESON_GATE(uart_a, SYS_CLK_EN1, 5);
+static MESON_GATE(sys_psram, SYS_CLK_EN1, 6);
+static MESON_GATE(rsa, SYS_CLK_EN1, 8);
+static MESON_GATE(coresight, SYS_CLK_EN1, 9);
+static MESON_GATE(am2axi_vad, AXI_CLK_EN, 0);
+static MESON_GATE(audio_vad, AXI_CLK_EN, 1);
+static MESON_GATE(axi_dmc, AXI_CLK_EN, 3);
+static MESON_GATE(axi_psram, AXI_CLK_EN, 4);
+static MESON_GATE(ramb, AXI_CLK_EN, 5);
+static MESON_GATE(rama, AXI_CLK_EN, 6);
+static MESON_GATE(axi_spifc, AXI_CLK_EN, 7);
+static MESON_GATE(axi_nic, AXI_CLK_EN, 8);
+static MESON_GATE(axi_dma, AXI_CLK_EN, 9);
+static MESON_GATE(cpu_ctrl, AXI_CLK_EN, 10);
+static MESON_GATE(rom, AXI_CLK_EN, 11);
+static MESON_GATE(prod_i2c, AXI_CLK_EN, 12);
+
+/* Array of all clocks registered by this provider */
+static struct clk_hw_onecell_data a1_periphs_clks = {
+ .hws = {
+ /* DT exposed clocks */
+ [CLKID_FIXPLL_IN] = &fixpll_in.hw,
+ [CLKID_USB_PHY_IN] = &usb_phy_in.hw,
+ [CLKID_USB_CTRL_IN] = &usb_ctrl_in.hw,
+ [CLKID_HIFIPLL_IN] = &hifipll_in.hw,
+ [CLKID_SYSPLL_IN] = &syspll_in.hw,
+ [CLKID_DDS_IN] = &dds_in.hw,
+ [CLKID_SYS] = &sys.hw,
+ [CLKID_CLKTREE] = &clktree.hw,
+ [CLKID_RESET_CTRL] = &reset_ctrl.hw,
+ [CLKID_ANALOG_CTRL] = &analog_ctrl.hw,
+ [CLKID_PWR_CTRL] = &pwr_ctrl.hw,
+ [CLKID_PAD_CTRL] = &pad_ctrl.hw,
+ [CLKID_SYS_CTRL] = &sys_ctrl.hw,
+ [CLKID_TEMP_SENSOR] = &temp_sensor.hw,
+ [CLKID_AM2AXI_DIV] = &am2axi_dev.hw,
+ [CLKID_SPICC_B] = &spicc_b.hw,
+ [CLKID_SPICC_A] = &spicc_a.hw,
+ [CLKID_MSR] = &msr.hw,
+ [CLKID_AUDIO] = &audio.hw,
+ [CLKID_JTAG_CTRL] = &jtag_ctrl.hw,
+ [CLKID_SARADC_EN] = &saradc_en.hw,
+ [CLKID_PWM_EF] = &pwm_ef.hw,
+ [CLKID_PWM_CD] = &pwm_cd.hw,
+ [CLKID_PWM_AB] = &pwm_ab.hw,
+ [CLKID_CEC] = &cec.hw,
+ [CLKID_I2C_S] = &i2c_s.hw,
+ [CLKID_IR_CTRL] = &ir_ctrl.hw,
+ [CLKID_I2C_M_D] = &i2c_m_d.hw,
+ [CLKID_I2C_M_C] = &i2c_m_c.hw,
+ [CLKID_I2C_M_B] = &i2c_m_b.hw,
+ [CLKID_I2C_M_A] = &i2c_m_a.hw,
+ [CLKID_ACODEC] = &acodec.hw,
+ [CLKID_OTP] = &otp.hw,
+ [CLKID_SD_EMMC_A] = &sd_emmc_a.hw,
+ [CLKID_USB_PHY] = &usb_phy.hw,
+ [CLKID_USB_CTRL] = &usb_ctrl.hw,
+ [CLKID_SYS_DSPB] = &sys_dspb.hw,
+ [CLKID_SYS_DSPA] = &sys_dspa.hw,
+ [CLKID_DMA] = &dma.hw,
+ [CLKID_IRQ_CTRL] = &irq_ctrl.hw,
+ [CLKID_NIC] = &nic.hw,
+ [CLKID_GIC] = &gic.hw,
+ [CLKID_UART_C] = &uart_c.hw,
+ [CLKID_UART_B] = &uart_b.hw,
+ [CLKID_UART_A] = &uart_a.hw,
+ [CLKID_SYS_PSRAM] = &sys_psram.hw,
+ [CLKID_RSA] = &rsa.hw,
+ [CLKID_CORESIGHT] = &coresight.hw,
+ [CLKID_AM2AXI_VAD] = &am2axi_vad.hw,
+ [CLKID_AUDIO_VAD] = &audio_vad.hw,
+ [CLKID_AXI_DMC] = &axi_dmc.hw,
+ [CLKID_AXI_PSRAM] = &axi_psram.hw,
+ [CLKID_RAMB] = &ramb.hw,
+ [CLKID_RAMA] = &rama.hw,
+ [CLKID_AXI_SPIFC] = &axi_spifc.hw,
+ [CLKID_AXI_NIC] = &axi_nic.hw,
+ [CLKID_AXI_DMA] = &axi_dma.hw,
+ [CLKID_CPU_CTRL] = &cpu_ctrl.hw,
+ [CLKID_ROM] = &rom.hw,
+ [CLKID_PROC_I2C] = &prod_i2c.hw,
+ [CLKID_DSPA_EN] = &dspa_en.hw,
+ [CLKID_DSPA_EN_NIC] = &dspa_en_nic.hw,
+ [CLKID_DSPB_EN] = &dspb_en.hw,
+ [CLKID_DSPB_EN_NIC] = &dspb_en_nic.hw,
+ [CLKID_RTC] = &rtc.hw,
+ [CLKID_CECA_32K] = &ceca_32k_out.hw,
+ [CLKID_CECB_32K] = &cecb_32k_out.hw,
+ [CLKID_24M] = &clk_24m.hw,
+ [CLKID_12M] = &clk_12m.hw,
+ [CLKID_FCLK_DIV2_DIVN] = &fclk_div2_divn.hw,
+ [CLKID_GEN] = &gen.hw,
+ [CLKID_SARADC] = &saradc.hw,
+ [CLKID_PWM_A] = &pwm_a.hw,
+ [CLKID_PWM_B] = &pwm_b.hw,
+ [CLKID_PWM_C] = &pwm_c.hw,
+ [CLKID_PWM_D] = &pwm_d.hw,
+ [CLKID_PWM_E] = &pwm_e.hw,
+ [CLKID_PWM_F] = &pwm_f.hw,
+ [CLKID_SPICC] = &spicc.hw,
+ [CLKID_TS] = &ts.hw,
+ [CLKID_SPIFC] = &spifc.hw,
+ [CLKID_USB_BUS] = &usb_bus.hw,
+ [CLKID_SD_EMMC] = &sd_emmc.hw,
+ [CLKID_PSRAM] = &psram.hw,
+ [CLKID_DMC] = &dmc.hw,
+ [CLKID_GEN_SEL] = &gen_sel.hw,
+ [CLKID_PWM_A_SEL] = &pwm_a_sel.hw,
+ [CLKID_PWM_B_SEL] = &pwm_b_sel.hw,
+ [CLKID_PWM_C_SEL] = &pwm_c_sel.hw,
+ [CLKID_PWM_D_SEL] = &pwm_d_sel.hw,
+ [CLKID_PWM_E_SEL] = &pwm_e_sel.hw,
+ [CLKID_PWM_F_SEL] = &pwm_f_sel.hw,
+ [CLKID_DSPA_A_SEL] = &dspa_a_sel.hw,
+ [CLKID_DSPA_B_SEL] = &dspa_b_sel.hw,
+ [CLKID_DSPB_A_SEL] = &dspb_a_sel.hw,
+ [CLKID_DSPB_B_SEL] = &dspb_b_sel.hw,
+ [CLKID_CECA_32K_SEL] = &ceca_32k_sel.hw,
+ [CLKID_CECA_32K_SEL_PRE] = &ceca_32k_sel_pre.hw,
+ [CLKID_CECB_32K_SEL] = &cecb_32k_sel.hw,
+ [CLKID_CECB_32K_SEL_PRE] = &cecb_32k_sel_pre.hw,
+
+ /* Internal clocks */
+ [CLKID_XTAL_IN] = &xtal_in.hw,
+ [CLKID_DSPA_SEL] = &dspa_sel.hw,
+ [CLKID_DSPB_SEL] = &dspb_sel.hw,
+ [CLKID_SARADC_SEL] = &saradc_sel.hw,
+ [CLKID_SYS_A_SEL] = &sys_a_sel.hw,
+ [CLKID_SYS_A_DIV] = &sys_a_div.hw,
+ [CLKID_SYS_A] = &sys_a.hw,
+ [CLKID_SYS_B_SEL] = &sys_b_sel.hw,
+ [CLKID_SYS_B_DIV] = &sys_b_div.hw,
+ [CLKID_SYS_B] = &sys_b.hw,
+ [CLKID_DSPA_A_DIV] = &dspa_a_div.hw,
+ [CLKID_DSPA_A] = &dspa_a.hw,
+ [CLKID_DSPA_B_DIV] = &dspa_b_div.hw,
+ [CLKID_DSPA_B] = &dspa_b.hw,
+ [CLKID_DSPB_A_DIV] = &dspb_a_div.hw,
+ [CLKID_DSPB_A] = &dspb_a.hw,
+ [CLKID_DSPB_B_DIV] = &dspb_b_div.hw,
+ [CLKID_DSPB_B] = &dspb_b.hw,
+ [CLKID_RTC_32K_IN] = &rtc_32k_in.hw,
+ [CLKID_RTC_32K_DIV] = &rtc_32k_div.hw,
+ [CLKID_RTC_32K_XTAL] = &rtc_32k_xtal.hw,
+ [CLKID_RTC_32K_SEL] = &rtc_32k_sel.hw,
+ [CLKID_CECB_32K_IN] = &cecb_32k_in.hw,
+ [CLKID_CECB_32K_DIV] = &cecb_32k_div.hw,
+ [CLKID_CECA_32K_IN] = &ceca_32k_in.hw,
+ [CLKID_CECA_32K_DIV] = &ceca_32k_div.hw,
+ [CLKID_DIV2_PRE] = &fclk_div2_divn_pre.hw,
+ [CLKID_24M_DIV2] = &clk_24m_div2.hw,
+ [CLKID_GEN_DIV] = &gen_div.hw,
+ [CLKID_SARADC_DIV] = &saradc_div.hw,
+ [CLKID_PWM_A_DIV] = &pwm_a_div.hw,
+ [CLKID_PWM_B_DIV] = &pwm_b_div.hw,
+ [CLKID_PWM_C_DIV] = &pwm_c_div.hw,
+ [CLKID_PWM_D_DIV] = &pwm_d_div.hw,
+ [CLKID_PWM_E_DIV] = &pwm_e_div.hw,
+ [CLKID_PWM_F_DIV] = &pwm_f_div.hw,
+ [CLKID_SPICC_SEL] = &spicc_sel.hw,
+ [CLKID_SPICC_DIV] = &spicc_div.hw,
+ [CLKID_SPICC_SEL2] = &spicc_sel2.hw,
+ [CLKID_TS_DIV] = &ts_div.hw,
+ [CLKID_SPIFC_SEL] = &spifc_sel.hw,
+ [CLKID_SPIFC_DIV] = &spifc_div.hw,
+ [CLKID_SPIFC_SEL2] = &spifc_sel2.hw,
+ [CLKID_USB_BUS_SEL] = &usb_bus_sel.hw,
+ [CLKID_USB_BUS_DIV] = &usb_bus_div.hw,
+ [CLKID_SD_EMMC_SEL] = &sd_emmc_sel.hw,
+ [CLKID_SD_EMMC_DIV] = &sd_emmc_div.hw,
+ [CLKID_SD_EMMC_SEL2] = &sd_emmc_sel2.hw,
+ [CLKID_PSRAM_SEL] = &psram_sel.hw,
+ [CLKID_PSRAM_DIV] = &psram_div.hw,
+ [CLKID_PSRAM_SEL2] = &psram_sel2.hw,
+ [CLKID_DMC_SEL] = &dmc_sel.hw,
+ [CLKID_DMC_DIV] = &dmc_div.hw,
+ [CLKID_DMC_SEL2] = &dmc_sel2.hw,
+
+ [NR_CLKS] = NULL,
+ },
+ .num = NR_CLKS,
+};
+
+/* Convenience table to populate regmap in .probe */
+static struct clk_regmap *const a1_periphs_regmaps[] = {
+ &xtal_in,
+ &fixpll_in,
+ &usb_phy_in,
+ &usb_ctrl_in,
+ &hifipll_in,
+ &syspll_in,
+ &dds_in,
+ &sys,
+ &clktree,
+ &reset_ctrl,
+ &analog_ctrl,
+ &pwr_ctrl,
+ &pad_ctrl,
+ &sys_ctrl,
+ &temp_sensor,
+ &am2axi_dev,
+ &spicc_b,
+ &spicc_a,
+ &msr,
+ &audio,
+ &jtag_ctrl,
+ &saradc_en,
+ &pwm_ef,
+ &pwm_cd,
+ &pwm_ab,
+ &cec,
+ &i2c_s,
+ &ir_ctrl,
+ &i2c_m_d,
+ &i2c_m_c,
+ &i2c_m_b,
+ &i2c_m_a,
+ &acodec,
+ &otp,
+ &sd_emmc_a,
+ &usb_phy,
+ &usb_ctrl,
+ &sys_dspb,
+ &sys_dspa,
+ &dma,
+ &irq_ctrl,
+ &nic,
+ &gic,
+ &uart_c,
+ &uart_b,
+ &uart_a,
+ &sys_psram,
+ &rsa,
+ &coresight,
+ &am2axi_vad,
+ &audio_vad,
+ &axi_dmc,
+ &axi_psram,
+ &ramb,
+ &rama,
+ &axi_spifc,
+ &axi_nic,
+ &axi_dma,
+ &cpu_ctrl,
+ &rom,
+ &prod_i2c,
+ &dspa_sel,
+ &dspb_sel,
+ &dspa_en,
+ &dspa_en_nic,
+ &dspb_en,
+ &dspb_en_nic,
+ &rtc,
+ &ceca_32k_out,
+ &cecb_32k_out,
+ &clk_24m,
+ &clk_12m,
+ &fclk_div2_divn,
+ &gen,
+ &saradc_sel,
+ &saradc,
+ &pwm_a,
+ &pwm_b,
+ &pwm_c,
+ &pwm_d,
+ &pwm_e,
+ &pwm_f,
+ &spicc,
+ &ts,
+ &spifc,
+ &usb_bus,
+ &sd_emmc,
+ &psram,
+ &dmc,
+ &sys_a_sel,
+ &sys_a_div,
+ &sys_a,
+ &sys_b_sel,
+ &sys_b_div,
+ &sys_b,
+ &dspa_a_sel,
+ &dspa_a_div,
+ &dspa_a,
+ &dspa_b_sel,
+ &dspa_b_div,
+ &dspa_b,
+ &dspb_a_sel,
+ &dspb_a_div,
+ &dspb_a,
+ &dspb_b_sel,
+ &dspb_b_div,
+ &dspb_b,
+ &rtc_32k_in,
+ &rtc_32k_div,
+ &rtc_32k_xtal,
+ &rtc_32k_sel,
+ &cecb_32k_in,
+ &cecb_32k_div,
+ &cecb_32k_sel_pre,
+ &cecb_32k_sel,
+ &ceca_32k_in,
+ &ceca_32k_div,
+ &ceca_32k_sel_pre,
+ &ceca_32k_sel,
+ &fclk_div2_divn_pre,
+ &gen_sel,
+ &gen_div,
+ &saradc_div,
+ &pwm_a_sel,
+ &pwm_a_div,
+ &pwm_b_sel,
+ &pwm_b_div,
+ &pwm_c_sel,
+ &pwm_c_div,
+ &pwm_d_sel,
+ &pwm_d_div,
+ &pwm_e_sel,
+ &pwm_e_div,
+ &pwm_f_sel,
+ &pwm_f_div,
+ &spicc_sel,
+ &spicc_div,
+ &spicc_sel2,
+ &ts_div,
+ &spifc_sel,
+ &spifc_div,
+ &spifc_sel2,
+ &usb_bus_sel,
+ &usb_bus_div,
+ &sd_emmc_sel,
+ &sd_emmc_div,
+ &sd_emmc_sel2,
+ &psram_sel,
+ &psram_div,
+ &psram_sel2,
+ &dmc_sel,
+ &dmc_div,
+ &dmc_sel2,
+};
+
+static struct regmap_config a1_periphs_regmap_cfg = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static int meson_a1_periphs_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ void __iomem *base;
+ struct regmap *map;
+ int clkid, i, err;
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return dev_err_probe(dev, PTR_ERR(base),
+ "can't ioremap resource\n");
+
+ map = devm_regmap_init_mmio(dev, base, &a1_periphs_regmap_cfg);
+ if (IS_ERR(map))
+ return dev_err_probe(dev, PTR_ERR(map),
+ "can't init regmap mmio region\n");
+
+ /* Populate regmap for the regmap backed clocks */
+ for (i = 0; i < ARRAY_SIZE(a1_periphs_regmaps); i++)
+ a1_periphs_regmaps[i]->map = map;
+
+ for (clkid = 0; clkid < a1_periphs_clks.num; clkid++) {
+ err = devm_clk_hw_register(dev, a1_periphs_clks.hws[clkid]);
+ if (err)
+ return dev_err_probe(dev, err,
+ "clock[%d] registration failed\n",
+ clkid);
+ }
+
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+ &a1_periphs_clks);
+}
+
+static const struct of_device_id a1_periphs_clkc_match_table[] = {
+ { .compatible = "amlogic,a1-clkc", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, a1_periphs_clkc_match_table);
+
+static struct platform_driver a1_periphs_clkc_driver = {
+ .probe = meson_a1_periphs_probe,
+ .driver = {
+ .name = "a1-clkc",
+ .of_match_table = of_match_ptr(a1_periphs_clkc_match_table),
+ },
+};
+
+module_platform_driver(a1_periphs_clkc_driver);
+MODULE_AUTHOR("Jian Hu <[email protected]>");
+MODULE_AUTHOR("Dmitry Rokosov <[email protected]>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/meson/a1.h b/drivers/clk/meson/a1.h
new file mode 100644
index 000000000000..89d592249ee6
--- /dev/null
+++ b/drivers/clk/meson/a1.h
@@ -0,0 +1,114 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Amlogic Meson-A1 Peripheral Clock Controller internals
+ *
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#ifndef __A1_H
+#define __A1_H
+
+/* peripheral clock controller register offset */
+#define SYS_OSCIN_CTRL 0x0
+#define RTC_BY_OSCIN_CTRL0 0x4
+#define RTC_BY_OSCIN_CTRL1 0x8
+#define RTC_CTRL 0xc
+#define SYS_CLK_CTRL0 0x10
+#define SYS_CLK_EN0 0x1c
+#define SYS_CLK_EN1 0x20
+#define AXI_CLK_EN 0x24
+#define DSPA_CLK_EN 0x28
+#define DSPB_CLK_EN 0x2c
+#define DSPA_CLK_CTRL0 0x30
+#define DSPB_CLK_CTRL0 0x34
+#define CLK12_24_CTRL 0x38
+#define GEN_CLK_CTRL 0x3c
+#define SAR_ADC_CLK_CTRL 0xc0
+#define PWM_CLK_AB_CTRL 0xc4
+#define PWM_CLK_CD_CTRL 0xc8
+#define PWM_CLK_EF_CTRL 0xcc
+#define SPICC_CLK_CTRL 0xd0
+#define TS_CLK_CTRL 0xd4
+#define SPIFC_CLK_CTRL 0xd8
+#define USB_BUSCLK_CTRL 0xdc
+#define SD_EMMC_CLK_CTRL 0xe0
+#define CECA_CLK_CTRL0 0xe4
+#define CECA_CLK_CTRL1 0xe8
+#define CECB_CLK_CTRL0 0xec
+#define CECB_CLK_CTRL1 0xf0
+#define PSRAM_CLK_CTRL 0xf4
+#define DMC_CLK_CTRL 0xf8
+
+/* include the CLKIDs that have been made part of the DT binding */
+#include <dt-bindings/clock/amlogic,a1-clkc.h>
+
+/*
+ * CLKID index values for internal clocks
+ *
+ * These indices are entirely contrived and do not map onto the hardware.
+ * It has now been decided to expose everything by default in the DT header:
+ * include/dt-bindings/clock/a1-clkc.h. Only the clocks ids we don't want
+ * to expose, such as the internal muxes and dividers of composite clocks,
+ * will remain defined here.
+ */
+#define CLKID_XTAL_IN 100
+#define CLKID_DSPA_SEL 101
+#define CLKID_DSPB_SEL 102
+#define CLKID_SARADC_SEL 103
+#define CLKID_SYS_A_SEL 104
+#define CLKID_SYS_A_DIV 105
+#define CLKID_SYS_A 106
+#define CLKID_SYS_B_SEL 107
+#define CLKID_SYS_B_DIV 108
+#define CLKID_SYS_B 109
+#define CLKID_DSPA_A_DIV 110
+#define CLKID_DSPA_A 111
+#define CLKID_DSPA_B_DIV 112
+#define CLKID_DSPA_B 113
+#define CLKID_DSPB_A_DIV 114
+#define CLKID_DSPB_A 115
+#define CLKID_DSPB_B_DIV 116
+#define CLKID_DSPB_B 117
+#define CLKID_RTC_32K_IN 118
+#define CLKID_RTC_32K_DIV 119
+#define CLKID_RTC_32K_XTAL 120
+#define CLKID_RTC_32K_SEL 121
+#define CLKID_CECB_32K_IN 122
+#define CLKID_CECB_32K_DIV 123
+#define CLKID_CECA_32K_IN 124
+#define CLKID_CECA_32K_DIV 125
+#define CLKID_DIV2_PRE 126
+#define CLKID_24M_DIV2 127
+#define CLKID_GEN_DIV 128
+#define CLKID_SARADC_DIV 129
+#define CLKID_PWM_A_DIV 130
+#define CLKID_PWM_B_DIV 131
+#define CLKID_PWM_C_DIV 132
+#define CLKID_PWM_D_DIV 133
+#define CLKID_PWM_E_DIV 134
+#define CLKID_PWM_F_DIV 135
+#define CLKID_SPICC_SEL 136
+#define CLKID_SPICC_DIV 137
+#define CLKID_SPICC_SEL2 138
+#define CLKID_TS_DIV 139
+#define CLKID_SPIFC_SEL 140
+#define CLKID_SPIFC_DIV 141
+#define CLKID_SPIFC_SEL2 142
+#define CLKID_USB_BUS_SEL 143
+#define CLKID_USB_BUS_DIV 144
+#define CLKID_SD_EMMC_SEL 145
+#define CLKID_SD_EMMC_DIV 146
+#define CLKID_SD_EMMC_SEL2 147
+#define CLKID_PSRAM_SEL 148
+#define CLKID_PSRAM_DIV 149
+#define CLKID_PSRAM_SEL2 150
+#define CLKID_DMC_SEL 151
+#define CLKID_DMC_DIV 152
+#define CLKID_DMC_SEL2 153
+#define NR_CLKS 154
+
+#endif /* __A1_H */
--
2.36.0
Introduce PLL clock controller for Amlogic A1 SoC family.
The clock unit is an APB slave module that is designed for generating all
of the internal and system clocks.
The SoC uses an external 24MHz crystal; there are 4 internal PLLs:
SYS_PLL/HIFI_PLL/USB_PLL/(FIXPLL), these PLLs generate 27 clock sources.
Signed-off-by: Jian Hu <[email protected]>
Signed-off-by: Dmitry Rokosov <[email protected]>
---
drivers/clk/meson/Kconfig | 10 ++
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/a1-pll.c | 360 +++++++++++++++++++++++++++++++++++++
drivers/clk/meson/a1-pll.h | 47 +++++
4 files changed, 418 insertions(+)
create mode 100644 drivers/clk/meson/a1-pll.c
create mode 100644 drivers/clk/meson/a1-pll.h
diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index fc002c155bc3..f56da2a4b000 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -99,6 +99,16 @@ config COMMON_CLK_AXG_AUDIO
Support for the audio clock controller on AmLogic A113D devices,
aka axg, Say Y if you want audio subsystem to work.
+config COMMON_CLK_A1_PLL
+ tristate "Meson A1 SoC PLL controller support"
+ depends on ARM64
+ select COMMON_CLK_MESON_REGMAP
+ select COMMON_CLK_MESON_PLL
+ help
+ Support for the PLL clock controller on Amlogic A113L based
+ device, A1 SoC Family. Say Y if you want A1 PLL clock controller
+ to work.
+
config COMMON_CLK_G12A
tristate "G12 and SM1 SoC clock controllers support"
depends on ARM64
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 6eca2a406ee3..2f17f475a48f 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
+obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
diff --git a/drivers/clk/meson/a1-pll.c b/drivers/clk/meson/a1-pll.c
new file mode 100644
index 000000000000..174d3676af36
--- /dev/null
+++ b/drivers/clk/meson/a1-pll.c
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "a1-pll.h"
+#include "clk-regmap.h"
+
+static struct clk_regmap fixed_pll_dco = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .frac = {
+ .reg_off = ANACTRL_FIXPLL_CTRL1,
+ .shift = 0,
+ .width = 19,
+ },
+ .l = {
+ .reg_off = ANACTRL_FIXPLL_STS,
+ .shift = 31,
+ .width = 1,
+ },
+ .rst = {
+ .reg_off = ANACTRL_FIXPLL_CTRL0,
+ .shift = 29,
+ .width = 1,
+ },
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fixed_pll_dco",
+ .ops = &meson_clk_pll_ro_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "fixpll_in",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fixed_pll = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 20,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "fixed_pll",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fixed_pll_dco.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static const struct pll_mult_range hifi_pll_mult_range = {
+ .min = 32,
+ .max = 64,
+};
+
+static const struct reg_sequence hifi_init_regs[] = {
+ { .reg = ANACTRL_HIFIPLL_CTRL1, .def = 0x01800000 },
+ { .reg = ANACTRL_HIFIPLL_CTRL2, .def = 0x00001100 },
+ { .reg = ANACTRL_HIFIPLL_CTRL3, .def = 0x100a1100 },
+ { .reg = ANACTRL_HIFIPLL_CTRL4, .def = 0x00302000 },
+ { .reg = ANACTRL_HIFIPLL_CTRL0, .def = 0x01f18000 },
+};
+
+static struct clk_regmap hifi_pll = {
+ .data = &(struct meson_clk_pll_data){
+ .en = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .m = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 0,
+ .width = 8,
+ },
+ .n = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 10,
+ .width = 5,
+ },
+ .frac = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL1,
+ .shift = 0,
+ .width = 19,
+ },
+ .l = {
+ .reg_off = ANACTRL_HIFIPLL_STS,
+ .shift = 31,
+ .width = 1,
+ },
+ .current_en = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL0,
+ .shift = 26,
+ .width = 1,
+ },
+ .l_detect = {
+ .reg_off = ANACTRL_HIFIPLL_CTRL2,
+ .shift = 6,
+ .width = 1,
+ },
+ .range = &hifi_pll_mult_range,
+ .init_regs = hifi_init_regs,
+ .init_count = ARRAY_SIZE(hifi_init_regs),
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "hifi_pll",
+ .ops = &meson_clk_pll_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "hifipll_in",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_fixed_factor fclk_div2_div = {
+ .mult = 1,
+ .div = 2,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div2 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 21,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fclk_div2_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * This clock is used by DDR clock in BL2 firmware
+ * and is required by the platform to operate correctly.
+ * Until the following condition are met, we need this clock to
+ * be marked as critical:
+ * a) Mark the clock used by a firmware resource, if possible
+ * b) CCF has a clock hand-off mechanism to make the sure the
+ * clock stays on until the proper driver comes along
+ */
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_fixed_factor fclk_div3_div = {
+ .mult = 1,
+ .div = 3,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div3_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div3 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 22,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div3",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fclk_div3_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * This clock is used by APB bus which is set in boot ROM code
+ * and is required by the platform to operate correctly.
+ */
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_fixed_factor fclk_div5_div = {
+ .mult = 1,
+ .div = 5,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div5_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div5 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 23,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div5",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fclk_div5_div.hw
+ },
+ .num_parents = 1,
+ /*
+ * This clock is used by AXI bus which setted in Romcode
+ * and is required by the platform to operate correctly.
+ */
+ .flags = CLK_IS_CRITICAL,
+ },
+};
+
+static struct clk_fixed_factor fclk_div7_div = {
+ .mult = 1,
+ .div = 7,
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div7_div",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fixed_pll.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div7 = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = ANACTRL_FIXPLL_CTRL0,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div7",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fclk_div7_div.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+/* Array of all clocks registered by this provider */
+static struct clk_hw_onecell_data a1_pll_clks = {
+ .hws = {
+ /* DT exposed clocks */
+ [CLKID_FIXED_PLL] = &fixed_pll.hw,
+ [CLKID_FCLK_DIV2] = &fclk_div2.hw,
+ [CLKID_FCLK_DIV3] = &fclk_div3.hw,
+ [CLKID_FCLK_DIV5] = &fclk_div5.hw,
+ [CLKID_FCLK_DIV7] = &fclk_div7.hw,
+ [CLKID_HIFI_PLL] = &hifi_pll.hw,
+
+ /* Internal clocks */
+ [CLKID_FIXED_PLL_DCO] = &fixed_pll_dco.hw,
+ [CLKID_FCLK_DIV2_DIV] = &fclk_div2_div.hw,
+ [CLKID_FCLK_DIV3_DIV] = &fclk_div3_div.hw,
+ [CLKID_FCLK_DIV5_DIV] = &fclk_div5_div.hw,
+ [CLKID_FCLK_DIV7_DIV] = &fclk_div7_div.hw,
+
+ [NR_PLL_CLKS] = NULL,
+ },
+ .num = NR_PLL_CLKS,
+};
+
+static struct clk_regmap *const a1_pll_regmaps[] = {
+ &fixed_pll_dco,
+ &fixed_pll,
+ &fclk_div2,
+ &fclk_div3,
+ &fclk_div5,
+ &fclk_div7,
+ &hifi_pll,
+};
+
+static struct regmap_config a1_pll_regmap_cfg = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static int meson_a1_pll_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ void __iomem *base;
+ struct regmap *map;
+ int clkid, i, err;
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return dev_err_probe(dev, PTR_ERR(base),
+ "can't ioremap resource\n");
+
+ map = devm_regmap_init_mmio(dev, base, &a1_pll_regmap_cfg);
+ if (IS_ERR(map))
+ return dev_err_probe(dev, PTR_ERR(map),
+ "can't init regmap mmio region\n");
+
+ /* Populate regmap for the regmap backed clocks */
+ for (i = 0; i < ARRAY_SIZE(a1_pll_regmaps); i++)
+ a1_pll_regmaps[i]->map = map;
+
+ /* Register clocks */
+ for (clkid = 0; clkid < a1_pll_clks.num; clkid++) {
+ err = devm_clk_hw_register(dev, a1_pll_clks.hws[clkid]);
+ if (err)
+ return dev_err_probe(dev, err,
+ "clock[%d] registration failed\n",
+ clkid);
+ }
+
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+ &a1_pll_clks);
+}
+
+static const struct of_device_id a1_pll_clkc_match_table[] = {
+ { .compatible = "amlogic,a1-pll-clkc", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, a1_pll_clkc_match_table);
+
+static struct platform_driver a1_pll_clkc_driver = {
+ .probe = meson_a1_pll_probe,
+ .driver = {
+ .name = "a1-pll-clkc",
+ .of_match_table = of_match_ptr(a1_pll_clkc_match_table),
+ },
+};
+
+module_platform_driver(a1_pll_clkc_driver);
+MODULE_AUTHOR("Jian Hu <[email protected]>");
+MODULE_AUTHOR("Dmitry Rokosov <[email protected]>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/meson/a1-pll.h b/drivers/clk/meson/a1-pll.h
new file mode 100644
index 000000000000..7dd9f81b057c
--- /dev/null
+++ b/drivers/clk/meson/a1-pll.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Amlogic Meson-A1 PLL Clock Controller internals
+ *
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#ifndef __A1_PLL_H
+#define __A1_PLL_H
+
+#include "clk-pll.h"
+
+/* PLL register offset */
+#define ANACTRL_FIXPLL_CTRL0 0x0
+#define ANACTRL_FIXPLL_CTRL1 0x4
+#define ANACTRL_FIXPLL_STS 0x14
+#define ANACTRL_HIFIPLL_CTRL0 0xc0
+#define ANACTRL_HIFIPLL_CTRL1 0xc4
+#define ANACTRL_HIFIPLL_CTRL2 0xc8
+#define ANACTRL_HIFIPLL_CTRL3 0xcc
+#define ANACTRL_HIFIPLL_CTRL4 0xd0
+#define ANACTRL_HIFIPLL_STS 0xd4
+
+/* include the CLKIDs that have been made part of the DT binding */
+#include <dt-bindings/clock/amlogic,a1-pll-clkc.h>
+
+/*
+ * CLKID index values for internal clocks
+ *
+ * These indices are entirely contrived and do not map onto the hardware.
+ * It has now been decided to expose everything by default in the DT header:
+ * include/dt-bindings/clock/a1-pll-clkc.h. Only the clocks ids we don't want
+ * to expose, such as the internal muxes and dividers of composite clocks,
+ * will remain defined here.
+ */
+#define CLKID_FIXED_PLL_DCO 6
+#define CLKID_FCLK_DIV2_DIV 7
+#define CLKID_FCLK_DIV3_DIV 8
+#define CLKID_FCLK_DIV5_DIV 9
+#define CLKID_FCLK_DIV7_DIV 10
+#define NR_PLL_CLKS 11
+
+#endif /* __A1_PLL_H */
--
2.36.0
On Tue 04 Apr 2023 at 18:53, Dmitry Rokosov <[email protected]> wrote:
> +/* Array of all clocks registered by this provider */
> +static struct clk_hw_onecell_data a1_periphs_clks = {
> + .hws = {
> + /* DT exposed clocks */
> + [CLKID_FIXPLL_IN] = &fixpll_in.hw,
> + [CLKID_USB_PHY_IN] = &usb_phy_in.hw,
> + [CLKID_USB_CTRL_IN] = &usb_ctrl_in.hw,
> + [CLKID_HIFIPLL_IN] = &hifipll_in.hw,
> + [CLKID_SYSPLL_IN] = &syspll_in.hw,
> + [CLKID_DDS_IN] = &dds_in.hw,
> + [CLKID_SYS] = &sys.hw,
> + [CLKID_CLKTREE] = &clktree.hw,
> + [CLKID_RESET_CTRL] = &reset_ctrl.hw,
> + [CLKID_ANALOG_CTRL] = &analog_ctrl.hw,
> + [CLKID_PWR_CTRL] = &pwr_ctrl.hw,
> + [CLKID_PAD_CTRL] = &pad_ctrl.hw,
> + [CLKID_SYS_CTRL] = &sys_ctrl.hw,
> + [CLKID_TEMP_SENSOR] = &temp_sensor.hw,
> + [CLKID_AM2AXI_DIV] = &am2axi_dev.hw,
> + [CLKID_SPICC_B] = &spicc_b.hw,
> + [CLKID_SPICC_A] = &spicc_a.hw,
> + [CLKID_MSR] = &msr.hw,
> + [CLKID_AUDIO] = &audio.hw,
> + [CLKID_JTAG_CTRL] = &jtag_ctrl.hw,
> + [CLKID_SARADC_EN] = &saradc_en.hw,
> + [CLKID_PWM_EF] = &pwm_ef.hw,
> + [CLKID_PWM_CD] = &pwm_cd.hw,
> + [CLKID_PWM_AB] = &pwm_ab.hw,
> + [CLKID_CEC] = &cec.hw,
> + [CLKID_I2C_S] = &i2c_s.hw,
> + [CLKID_IR_CTRL] = &ir_ctrl.hw,
> + [CLKID_I2C_M_D] = &i2c_m_d.hw,
> + [CLKID_I2C_M_C] = &i2c_m_c.hw,
> + [CLKID_I2C_M_B] = &i2c_m_b.hw,
> + [CLKID_I2C_M_A] = &i2c_m_a.hw,
> + [CLKID_ACODEC] = &acodec.hw,
> + [CLKID_OTP] = &otp.hw,
> + [CLKID_SD_EMMC_A] = &sd_emmc_a.hw,
> + [CLKID_USB_PHY] = &usb_phy.hw,
> + [CLKID_USB_CTRL] = &usb_ctrl.hw,
> + [CLKID_SYS_DSPB] = &sys_dspb.hw,
> + [CLKID_SYS_DSPA] = &sys_dspa.hw,
> + [CLKID_DMA] = &dma.hw,
> + [CLKID_IRQ_CTRL] = &irq_ctrl.hw,
> + [CLKID_NIC] = &nic.hw,
> + [CLKID_GIC] = &gic.hw,
> + [CLKID_UART_C] = &uart_c.hw,
> + [CLKID_UART_B] = &uart_b.hw,
> + [CLKID_UART_A] = &uart_a.hw,
> + [CLKID_SYS_PSRAM] = &sys_psram.hw,
> + [CLKID_RSA] = &rsa.hw,
> + [CLKID_CORESIGHT] = &coresight.hw,
> + [CLKID_AM2AXI_VAD] = &am2axi_vad.hw,
> + [CLKID_AUDIO_VAD] = &audio_vad.hw,
> + [CLKID_AXI_DMC] = &axi_dmc.hw,
> + [CLKID_AXI_PSRAM] = &axi_psram.hw,
> + [CLKID_RAMB] = &ramb.hw,
> + [CLKID_RAMA] = &rama.hw,
> + [CLKID_AXI_SPIFC] = &axi_spifc.hw,
> + [CLKID_AXI_NIC] = &axi_nic.hw,
> + [CLKID_AXI_DMA] = &axi_dma.hw,
> + [CLKID_CPU_CTRL] = &cpu_ctrl.hw,
> + [CLKID_ROM] = &rom.hw,
> + [CLKID_PROC_I2C] = &prod_i2c.hw,
> + [CLKID_DSPA_EN] = &dspa_en.hw,
> + [CLKID_DSPA_EN_NIC] = &dspa_en_nic.hw,
> + [CLKID_DSPB_EN] = &dspb_en.hw,
> + [CLKID_DSPB_EN_NIC] = &dspb_en_nic.hw,
> + [CLKID_RTC] = &rtc.hw,
> + [CLKID_CECA_32K] = &ceca_32k_out.hw,
> + [CLKID_CECB_32K] = &cecb_32k_out.hw,
> + [CLKID_24M] = &clk_24m.hw,
> + [CLKID_12M] = &clk_12m.hw,
> + [CLKID_FCLK_DIV2_DIVN] = &fclk_div2_divn.hw,
> + [CLKID_GEN] = &gen.hw,
> + [CLKID_SARADC] = &saradc.hw,
> + [CLKID_PWM_A] = &pwm_a.hw,
> + [CLKID_PWM_B] = &pwm_b.hw,
> + [CLKID_PWM_C] = &pwm_c.hw,
> + [CLKID_PWM_D] = &pwm_d.hw,
> + [CLKID_PWM_E] = &pwm_e.hw,
> + [CLKID_PWM_F] = &pwm_f.hw,
> + [CLKID_SPICC] = &spicc.hw,
> + [CLKID_TS] = &ts.hw,
> + [CLKID_SPIFC] = &spifc.hw,
> + [CLKID_USB_BUS] = &usb_bus.hw,
> + [CLKID_SD_EMMC] = &sd_emmc.hw,
> + [CLKID_PSRAM] = &psram.hw,
> + [CLKID_DMC] = &dmc.hw,
> + [CLKID_GEN_SEL] = &gen_sel.hw,
> + [CLKID_PWM_A_SEL] = &pwm_a_sel.hw,
> + [CLKID_PWM_B_SEL] = &pwm_b_sel.hw,
> + [CLKID_PWM_C_SEL] = &pwm_c_sel.hw,
> + [CLKID_PWM_D_SEL] = &pwm_d_sel.hw,
> + [CLKID_PWM_E_SEL] = &pwm_e_sel.hw,
> + [CLKID_PWM_F_SEL] = &pwm_f_sel.hw,
> + [CLKID_DSPA_A_SEL] = &dspa_a_sel.hw,
> + [CLKID_DSPA_B_SEL] = &dspa_b_sel.hw,
> + [CLKID_DSPB_A_SEL] = &dspb_a_sel.hw,
> + [CLKID_DSPB_B_SEL] = &dspb_b_sel.hw,
> + [CLKID_CECA_32K_SEL] = &ceca_32k_sel.hw,
> + [CLKID_CECA_32K_SEL_PRE] = &ceca_32k_sel_pre.hw,
> + [CLKID_CECB_32K_SEL] = &cecb_32k_sel.hw,
> + [CLKID_CECB_32K_SEL_PRE] = &cecb_32k_sel_pre.hw,
> +
> + /* Internal clocks */
There is no need to make such groups within the table.
I don't think such change was requested in the previous reviews.
Also grouping the IDs the way you did is a bad idea.
1) Since the clocks are registered in the order of the table, this will
make a lot of orphans during the registration of the controller. It does
work but it is not ideal performance wise. Whenever possible, it is
better to register the clocks from the roots to the leafs.
2) These 2 nice groups are going away the minute you add another clock which
was not part of the original submission. This is why IDs have no meaning,
no even groups.
> + [CLKID_XTAL_IN] = &xtal_in.hw,
> + [CLKID_DSPA_SEL] = &dspa_sel.hw,
> + [CLKID_DSPB_SEL] = &dspb_sel.hw,
> + [CLKID_SARADC_SEL] = &saradc_sel.hw,
> + [CLKID_SYS_A_SEL] = &sys_a_sel.hw,
> + [CLKID_SYS_A_DIV] = &sys_a_div.hw,
> + [CLKID_SYS_A] = &sys_a.hw,
> + [CLKID_SYS_B_SEL] = &sys_b_sel.hw,
> + [CLKID_SYS_B_DIV] = &sys_b_div.hw,
> + [CLKID_SYS_B] = &sys_b.hw,
> + [CLKID_DSPA_A_DIV] = &dspa_a_div.hw,
> + [CLKID_DSPA_A] = &dspa_a.hw,
> + [CLKID_DSPA_B_DIV] = &dspa_b_div.hw,
> + [CLKID_DSPA_B] = &dspa_b.hw,
> + [CLKID_DSPB_A_DIV] = &dspb_a_div.hw,
> + [CLKID_DSPB_A] = &dspb_a.hw,
> + [CLKID_DSPB_B_DIV] = &dspb_b_div.hw,
> + [CLKID_DSPB_B] = &dspb_b.hw,
> + [CLKID_RTC_32K_IN] = &rtc_32k_in.hw,
> + [CLKID_RTC_32K_DIV] = &rtc_32k_div.hw,
> + [CLKID_RTC_32K_XTAL] = &rtc_32k_xtal.hw,
> + [CLKID_RTC_32K_SEL] = &rtc_32k_sel.hw,
> + [CLKID_CECB_32K_IN] = &cecb_32k_in.hw,
> + [CLKID_CECB_32K_DIV] = &cecb_32k_div.hw,
> + [CLKID_CECA_32K_IN] = &ceca_32k_in.hw,
> + [CLKID_CECA_32K_DIV] = &ceca_32k_div.hw,
> + [CLKID_DIV2_PRE] = &fclk_div2_divn_pre.hw,
> + [CLKID_24M_DIV2] = &clk_24m_div2.hw,
> + [CLKID_GEN_DIV] = &gen_div.hw,
> + [CLKID_SARADC_DIV] = &saradc_div.hw,
> + [CLKID_PWM_A_DIV] = &pwm_a_div.hw,
> + [CLKID_PWM_B_DIV] = &pwm_b_div.hw,
> + [CLKID_PWM_C_DIV] = &pwm_c_div.hw,
> + [CLKID_PWM_D_DIV] = &pwm_d_div.hw,
> + [CLKID_PWM_E_DIV] = &pwm_e_div.hw,
> + [CLKID_PWM_F_DIV] = &pwm_f_div.hw,
> + [CLKID_SPICC_SEL] = &spicc_sel.hw,
> + [CLKID_SPICC_DIV] = &spicc_div.hw,
> + [CLKID_SPICC_SEL2] = &spicc_sel2.hw,
> + [CLKID_TS_DIV] = &ts_div.hw,
> + [CLKID_SPIFC_SEL] = &spifc_sel.hw,
> + [CLKID_SPIFC_DIV] = &spifc_div.hw,
> + [CLKID_SPIFC_SEL2] = &spifc_sel2.hw,
> + [CLKID_USB_BUS_SEL] = &usb_bus_sel.hw,
> + [CLKID_USB_BUS_DIV] = &usb_bus_div.hw,
> + [CLKID_SD_EMMC_SEL] = &sd_emmc_sel.hw,
> + [CLKID_SD_EMMC_DIV] = &sd_emmc_div.hw,
> + [CLKID_SD_EMMC_SEL2] = &sd_emmc_sel2.hw,
> + [CLKID_PSRAM_SEL] = &psram_sel.hw,
> + [CLKID_PSRAM_DIV] = &psram_div.hw,
> + [CLKID_PSRAM_SEL2] = &psram_sel2.hw,
> + [CLKID_DMC_SEL] = &dmc_sel.hw,
> + [CLKID_DMC_DIV] = &dmc_div.hw,
> + [CLKID_DMC_SEL2] = &dmc_sel2.hw,
> +
> + [NR_CLKS] = NULL,
> + },
> + .num = NR_CLKS,
> +};
On Wed, Apr 05, 2023 at 04:13:44PM +0200, Jerome Brunet wrote:
>
> On Tue 04 Apr 2023 at 18:53, Dmitry Rokosov <[email protected]> wrote:
>
> > +/* Array of all clocks registered by this provider */
> > +static struct clk_hw_onecell_data a1_periphs_clks = {
> > + .hws = {
> > + /* DT exposed clocks */
> > + [CLKID_FIXPLL_IN] = &fixpll_in.hw,
> > + [CLKID_USB_PHY_IN] = &usb_phy_in.hw,
> > + [CLKID_USB_CTRL_IN] = &usb_ctrl_in.hw,
> > + [CLKID_HIFIPLL_IN] = &hifipll_in.hw,
> > + [CLKID_SYSPLL_IN] = &syspll_in.hw,
> > + [CLKID_DDS_IN] = &dds_in.hw,
> > + [CLKID_SYS] = &sys.hw,
> > + [CLKID_CLKTREE] = &clktree.hw,
> > + [CLKID_RESET_CTRL] = &reset_ctrl.hw,
> > + [CLKID_ANALOG_CTRL] = &analog_ctrl.hw,
> > + [CLKID_PWR_CTRL] = &pwr_ctrl.hw,
> > + [CLKID_PAD_CTRL] = &pad_ctrl.hw,
> > + [CLKID_SYS_CTRL] = &sys_ctrl.hw,
> > + [CLKID_TEMP_SENSOR] = &temp_sensor.hw,
> > + [CLKID_AM2AXI_DIV] = &am2axi_dev.hw,
> > + [CLKID_SPICC_B] = &spicc_b.hw,
> > + [CLKID_SPICC_A] = &spicc_a.hw,
> > + [CLKID_MSR] = &msr.hw,
> > + [CLKID_AUDIO] = &audio.hw,
> > + [CLKID_JTAG_CTRL] = &jtag_ctrl.hw,
> > + [CLKID_SARADC_EN] = &saradc_en.hw,
> > + [CLKID_PWM_EF] = &pwm_ef.hw,
> > + [CLKID_PWM_CD] = &pwm_cd.hw,
> > + [CLKID_PWM_AB] = &pwm_ab.hw,
> > + [CLKID_CEC] = &cec.hw,
> > + [CLKID_I2C_S] = &i2c_s.hw,
> > + [CLKID_IR_CTRL] = &ir_ctrl.hw,
> > + [CLKID_I2C_M_D] = &i2c_m_d.hw,
> > + [CLKID_I2C_M_C] = &i2c_m_c.hw,
> > + [CLKID_I2C_M_B] = &i2c_m_b.hw,
> > + [CLKID_I2C_M_A] = &i2c_m_a.hw,
> > + [CLKID_ACODEC] = &acodec.hw,
> > + [CLKID_OTP] = &otp.hw,
> > + [CLKID_SD_EMMC_A] = &sd_emmc_a.hw,
> > + [CLKID_USB_PHY] = &usb_phy.hw,
> > + [CLKID_USB_CTRL] = &usb_ctrl.hw,
> > + [CLKID_SYS_DSPB] = &sys_dspb.hw,
> > + [CLKID_SYS_DSPA] = &sys_dspa.hw,
> > + [CLKID_DMA] = &dma.hw,
> > + [CLKID_IRQ_CTRL] = &irq_ctrl.hw,
> > + [CLKID_NIC] = &nic.hw,
> > + [CLKID_GIC] = &gic.hw,
> > + [CLKID_UART_C] = &uart_c.hw,
> > + [CLKID_UART_B] = &uart_b.hw,
> > + [CLKID_UART_A] = &uart_a.hw,
> > + [CLKID_SYS_PSRAM] = &sys_psram.hw,
> > + [CLKID_RSA] = &rsa.hw,
> > + [CLKID_CORESIGHT] = &coresight.hw,
> > + [CLKID_AM2AXI_VAD] = &am2axi_vad.hw,
> > + [CLKID_AUDIO_VAD] = &audio_vad.hw,
> > + [CLKID_AXI_DMC] = &axi_dmc.hw,
> > + [CLKID_AXI_PSRAM] = &axi_psram.hw,
> > + [CLKID_RAMB] = &ramb.hw,
> > + [CLKID_RAMA] = &rama.hw,
> > + [CLKID_AXI_SPIFC] = &axi_spifc.hw,
> > + [CLKID_AXI_NIC] = &axi_nic.hw,
> > + [CLKID_AXI_DMA] = &axi_dma.hw,
> > + [CLKID_CPU_CTRL] = &cpu_ctrl.hw,
> > + [CLKID_ROM] = &rom.hw,
> > + [CLKID_PROC_I2C] = &prod_i2c.hw,
> > + [CLKID_DSPA_EN] = &dspa_en.hw,
> > + [CLKID_DSPA_EN_NIC] = &dspa_en_nic.hw,
> > + [CLKID_DSPB_EN] = &dspb_en.hw,
> > + [CLKID_DSPB_EN_NIC] = &dspb_en_nic.hw,
> > + [CLKID_RTC] = &rtc.hw,
> > + [CLKID_CECA_32K] = &ceca_32k_out.hw,
> > + [CLKID_CECB_32K] = &cecb_32k_out.hw,
> > + [CLKID_24M] = &clk_24m.hw,
> > + [CLKID_12M] = &clk_12m.hw,
> > + [CLKID_FCLK_DIV2_DIVN] = &fclk_div2_divn.hw,
> > + [CLKID_GEN] = &gen.hw,
> > + [CLKID_SARADC] = &saradc.hw,
> > + [CLKID_PWM_A] = &pwm_a.hw,
> > + [CLKID_PWM_B] = &pwm_b.hw,
> > + [CLKID_PWM_C] = &pwm_c.hw,
> > + [CLKID_PWM_D] = &pwm_d.hw,
> > + [CLKID_PWM_E] = &pwm_e.hw,
> > + [CLKID_PWM_F] = &pwm_f.hw,
> > + [CLKID_SPICC] = &spicc.hw,
> > + [CLKID_TS] = &ts.hw,
> > + [CLKID_SPIFC] = &spifc.hw,
> > + [CLKID_USB_BUS] = &usb_bus.hw,
> > + [CLKID_SD_EMMC] = &sd_emmc.hw,
> > + [CLKID_PSRAM] = &psram.hw,
> > + [CLKID_DMC] = &dmc.hw,
> > + [CLKID_GEN_SEL] = &gen_sel.hw,
> > + [CLKID_PWM_A_SEL] = &pwm_a_sel.hw,
> > + [CLKID_PWM_B_SEL] = &pwm_b_sel.hw,
> > + [CLKID_PWM_C_SEL] = &pwm_c_sel.hw,
> > + [CLKID_PWM_D_SEL] = &pwm_d_sel.hw,
> > + [CLKID_PWM_E_SEL] = &pwm_e_sel.hw,
> > + [CLKID_PWM_F_SEL] = &pwm_f_sel.hw,
> > + [CLKID_DSPA_A_SEL] = &dspa_a_sel.hw,
> > + [CLKID_DSPA_B_SEL] = &dspa_b_sel.hw,
> > + [CLKID_DSPB_A_SEL] = &dspb_a_sel.hw,
> > + [CLKID_DSPB_B_SEL] = &dspb_b_sel.hw,
> > + [CLKID_CECA_32K_SEL] = &ceca_32k_sel.hw,
> > + [CLKID_CECA_32K_SEL_PRE] = &ceca_32k_sel_pre.hw,
> > + [CLKID_CECB_32K_SEL] = &cecb_32k_sel.hw,
> > + [CLKID_CECB_32K_SEL_PRE] = &cecb_32k_sel_pre.hw,
> > +
> > + /* Internal clocks */
>
> There is no need to make such groups within the table.
> I don't think such change was requested in the previous reviews.
>
> Also grouping the IDs the way you did is a bad idea.
>
> 1) Since the clocks are registered in the order of the table, this will
> make a lot of orphans during the registration of the controller. It does
> work but it is not ideal performance wise. Whenever possible, it is
> better to register the clocks from the roots to the leafs.
>
> 2) These 2 nice groups are going away the minute you add another clock which
> was not part of the original submission. This is why IDs have no meaning,
> no even groups.
>
In my opinion, it would be clearer to have two separate lists for 'exposed'
and 'internal' clocks. Krzysztof has previously mentioned that non-linear
IDs in the bindings are not a good solution, but I understand the argument
for improved performance. Therefore, I will change the ID order from root to
leaf nodes.
> > + [CLKID_XTAL_IN] = &xtal_in.hw,
> > + [CLKID_DSPA_SEL] = &dspa_sel.hw,
> > + [CLKID_DSPB_SEL] = &dspb_sel.hw,
> > + [CLKID_SARADC_SEL] = &saradc_sel.hw,
> > + [CLKID_SYS_A_SEL] = &sys_a_sel.hw,
> > + [CLKID_SYS_A_DIV] = &sys_a_div.hw,
> > + [CLKID_SYS_A] = &sys_a.hw,
> > + [CLKID_SYS_B_SEL] = &sys_b_sel.hw,
> > + [CLKID_SYS_B_DIV] = &sys_b_div.hw,
> > + [CLKID_SYS_B] = &sys_b.hw,
> > + [CLKID_DSPA_A_DIV] = &dspa_a_div.hw,
> > + [CLKID_DSPA_A] = &dspa_a.hw,
> > + [CLKID_DSPA_B_DIV] = &dspa_b_div.hw,
> > + [CLKID_DSPA_B] = &dspa_b.hw,
> > + [CLKID_DSPB_A_DIV] = &dspb_a_div.hw,
> > + [CLKID_DSPB_A] = &dspb_a.hw,
> > + [CLKID_DSPB_B_DIV] = &dspb_b_div.hw,
> > + [CLKID_DSPB_B] = &dspb_b.hw,
> > + [CLKID_RTC_32K_IN] = &rtc_32k_in.hw,
> > + [CLKID_RTC_32K_DIV] = &rtc_32k_div.hw,
> > + [CLKID_RTC_32K_XTAL] = &rtc_32k_xtal.hw,
> > + [CLKID_RTC_32K_SEL] = &rtc_32k_sel.hw,
> > + [CLKID_CECB_32K_IN] = &cecb_32k_in.hw,
> > + [CLKID_CECB_32K_DIV] = &cecb_32k_div.hw,
> > + [CLKID_CECA_32K_IN] = &ceca_32k_in.hw,
> > + [CLKID_CECA_32K_DIV] = &ceca_32k_div.hw,
> > + [CLKID_DIV2_PRE] = &fclk_div2_divn_pre.hw,
> > + [CLKID_24M_DIV2] = &clk_24m_div2.hw,
> > + [CLKID_GEN_DIV] = &gen_div.hw,
> > + [CLKID_SARADC_DIV] = &saradc_div.hw,
> > + [CLKID_PWM_A_DIV] = &pwm_a_div.hw,
> > + [CLKID_PWM_B_DIV] = &pwm_b_div.hw,
> > + [CLKID_PWM_C_DIV] = &pwm_c_div.hw,
> > + [CLKID_PWM_D_DIV] = &pwm_d_div.hw,
> > + [CLKID_PWM_E_DIV] = &pwm_e_div.hw,
> > + [CLKID_PWM_F_DIV] = &pwm_f_div.hw,
> > + [CLKID_SPICC_SEL] = &spicc_sel.hw,
> > + [CLKID_SPICC_DIV] = &spicc_div.hw,
> > + [CLKID_SPICC_SEL2] = &spicc_sel2.hw,
> > + [CLKID_TS_DIV] = &ts_div.hw,
> > + [CLKID_SPIFC_SEL] = &spifc_sel.hw,
> > + [CLKID_SPIFC_DIV] = &spifc_div.hw,
> > + [CLKID_SPIFC_SEL2] = &spifc_sel2.hw,
> > + [CLKID_USB_BUS_SEL] = &usb_bus_sel.hw,
> > + [CLKID_USB_BUS_DIV] = &usb_bus_div.hw,
> > + [CLKID_SD_EMMC_SEL] = &sd_emmc_sel.hw,
> > + [CLKID_SD_EMMC_DIV] = &sd_emmc_div.hw,
> > + [CLKID_SD_EMMC_SEL2] = &sd_emmc_sel2.hw,
> > + [CLKID_PSRAM_SEL] = &psram_sel.hw,
> > + [CLKID_PSRAM_DIV] = &psram_div.hw,
> > + [CLKID_PSRAM_SEL2] = &psram_sel2.hw,
> > + [CLKID_DMC_SEL] = &dmc_sel.hw,
> > + [CLKID_DMC_DIV] = &dmc_div.hw,
> > + [CLKID_DMC_SEL2] = &dmc_sel2.hw,
> > +
> > + [NR_CLKS] = NULL,
> > + },
> > + .num = NR_CLKS,
> > +};
--
Thank you,
Dmitry