The VIA VL813 USB3.0 hub appears to have an issue with autosuspend and
detecting USB3 devices. This can be reproduced by connecting a USB3
device to the hub after the hub enters autosuspend mode.
//connect the hub
[ 106.854204] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 107.084993] usb 2-1: New USB device found, idVendor=2109, idProduct=0813, bcdDevice=90.15
[ 107.094520] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 107.111836] usb 2-1: Product: USB3.0 Hub
[ 107.116835] usb 2-1: Manufacturer: VIA Labs, Inc.
[ 107.314230] hub 2-1:1.0: USB hub found
[ 107.321356] hub 2-1:1.0: 4 ports detected
//the hub enters autosuspend mode
[ 107.738873] hub 2-1:1.0: hub_suspend
[ 107.922097] usb 2-1: usb auto-suspend, wakeup 1
//connect a USB3 device
[ 133.120060] usb 2-1: usb wakeup-resume
[ 133.160033] usb 2-1: Waited 0ms for CONNECT
[ 133.165423] usb 2-1: finish resume
[ 133.176919] hub 2-1:1.0: hub_resume
[ 133.188026] usb 2-1-port3: status 0263 change 0041
[ 133.323585] hub 2-1:1.0: state 7 ports 4 chg 0008 evt 0008
[ 133.342423] usb 2-1-port3: link state change
[ 133.358154] usb 2-1-port3: status 0263, change 0040, 5.0 Gb/s
[ 133.875150] usb 2-1-port3: not reset yet, waiting 10ms
[ 133.895502] usb 2-1-port3: not reset yet, waiting 10ms
[ 133.918239] usb 2-1-port3: not reset yet, waiting 200ms
[ 134.139529] usb 2-1-port3: not reset yet, waiting 200ms
[ 134.365296] usb 2-1-port3: not reset yet, waiting 200ms
[ 134.590185] usb 2-1-port3: not reset yet, waiting 200ms
[ 134.641330] hub 2-1:1.0: state 7 ports 4 chg 0000 evt 0008
[ 134.658880] hub 2-1:1.0: hub_suspend
[ 134.792908] usb 2-1: usb auto-suspend, wakeup 1
Disabling autosuspend for this hub resolves the issue.
Signed-off-by: Jimmy Hu <[email protected]>
Cc: [email protected]
---
drivers/usb/core/hub.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 97a0f8faea6e..5c6455224d9d 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -47,6 +47,8 @@
#define USB_VENDOR_TEXAS_INSTRUMENTS 0x0451
#define USB_PRODUCT_TUSB8041_USB3 0x8140
#define USB_PRODUCT_TUSB8041_USB2 0x8142
+#define USB_VENDOR_VIA 0x2109
+#define USB_PRODUCT_VL813_USB3 0x0813
#define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND 0x01
#define HUB_QUIRK_DISABLE_AUTOSUSPEND 0x02
@@ -5866,6 +5868,11 @@ static const struct usb_device_id hub_id_table[] = {
.idVendor = USB_VENDOR_TEXAS_INSTRUMENTS,
.idProduct = USB_PRODUCT_TUSB8041_USB3,
.driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND},
+ { .match_flags = USB_DEVICE_ID_MATCH_VENDOR
+ | USB_DEVICE_ID_MATCH_PRODUCT,
+ .idVendor = USB_VENDOR_VIA,
+ .idProduct = USB_PRODUCT_VL813_USB3,
+ .driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND},
{ .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS,
.bDeviceClass = USB_CLASS_HUB},
{ .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS,
--
2.40.0.577.gac1e443424-goog
On 11.04.23 10:31, Jimmy Hu wrote:
> The VIA VL813 USB3.0 hub appears to have an issue with autosuspend and
> detecting USB3 devices. This can be reproduced by connecting a USB3
> device to the hub after the hub enters autosuspend mode.
Hi,
out of interest, could you test whether this also applies to disconnections?
That is, does the hub reliably wake up if you unplug a device?
Regards
Oliver
On Tue, Apr 11, 2023 at 08:31:45AM +0000, Jimmy Hu wrote:
> The VIA VL813 USB3.0 hub appears to have an issue with autosuspend and
> detecting USB3 devices. This can be reproduced by connecting a USB3
> device to the hub after the hub enters autosuspend mode.
>
> //connect the hub
> [ 106.854204] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
> [ 107.084993] usb 2-1: New USB device found, idVendor=2109, idProduct=0813, bcdDevice=90.15
> [ 107.094520] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> [ 107.111836] usb 2-1: Product: USB3.0 Hub
> [ 107.116835] usb 2-1: Manufacturer: VIA Labs, Inc.
> [ 107.314230] hub 2-1:1.0: USB hub found
> [ 107.321356] hub 2-1:1.0: 4 ports detected
>
> //the hub enters autosuspend mode
> [ 107.738873] hub 2-1:1.0: hub_suspend
> [ 107.922097] usb 2-1: usb auto-suspend, wakeup 1
>
> //connect a USB3 device
> [ 133.120060] usb 2-1: usb wakeup-resume
> [ 133.160033] usb 2-1: Waited 0ms for CONNECT
> [ 133.165423] usb 2-1: finish resume
> [ 133.176919] hub 2-1:1.0: hub_resume
> [ 133.188026] usb 2-1-port3: status 0263 change 0041
> [ 133.323585] hub 2-1:1.0: state 7 ports 4 chg 0008 evt 0008
> [ 133.342423] usb 2-1-port3: link state change
> [ 133.358154] usb 2-1-port3: status 0263, change 0040, 5.0 Gb/s
This status value indicates that the port is in the U3 suspend state.
Maybe the port needs to be put back into U0 before it can be reset.
> [ 133.875150] usb 2-1-port3: not reset yet, waiting 10ms
> [ 133.895502] usb 2-1-port3: not reset yet, waiting 10ms
> [ 133.918239] usb 2-1-port3: not reset yet, waiting 200ms
> [ 134.139529] usb 2-1-port3: not reset yet, waiting 200ms
> [ 134.365296] usb 2-1-port3: not reset yet, waiting 200ms
> [ 134.590185] usb 2-1-port3: not reset yet, waiting 200ms
> [ 134.641330] hub 2-1:1.0: state 7 ports 4 chg 0000 evt 0008
> [ 134.658880] hub 2-1:1.0: hub_suspend
> [ 134.792908] usb 2-1: usb auto-suspend, wakeup 1
>
> Disabling autosuspend for this hub resolves the issue.
It may be possible to fix the problem. You should try that before
giving up.
Alan Stern
On Tue, Apr 11, 2023 at 9:55 PM Alan Stern <[email protected]> wrote:
>
> On Tue, Apr 11, 2023 at 08:31:45AM +0000, Jimmy Hu wrote:
> > The VIA VL813 USB3.0 hub appears to have an issue with autosuspend and
> > detecting USB3 devices. This can be reproduced by connecting a USB3
> > device to the hub after the hub enters autosuspend mode.
> >
> > //connect the hub
> > [ 106.854204] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
> > [ 107.084993] usb 2-1: New USB device found, idVendor=2109, idProduct=0813, bcdDevice=90.15
> > [ 107.094520] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> > [ 107.111836] usb 2-1: Product: USB3.0 Hub
> > [ 107.116835] usb 2-1: Manufacturer: VIA Labs, Inc.
> > [ 107.314230] hub 2-1:1.0: USB hub found
> > [ 107.321356] hub 2-1:1.0: 4 ports detected
> >
> > //the hub enters autosuspend mode
> > [ 107.738873] hub 2-1:1.0: hub_suspend
> > [ 107.922097] usb 2-1: usb auto-suspend, wakeup 1
> >
> > //connect a USB3 device
> > [ 133.120060] usb 2-1: usb wakeup-resume
> > [ 133.160033] usb 2-1: Waited 0ms for CONNECT
> > [ 133.165423] usb 2-1: finish resume
> > [ 133.176919] hub 2-1:1.0: hub_resume
> > [ 133.188026] usb 2-1-port3: status 0263 change 0041
> > [ 133.323585] hub 2-1:1.0: state 7 ports 4 chg 0008 evt 0008
> > [ 133.342423] usb 2-1-port3: link state change
> > [ 133.358154] usb 2-1-port3: status 0263, change 0040, 5.0 Gb/s
>
> This status value indicates that the port is in the U3 suspend state.
> Maybe the port needs to be put back into U0 before it can be reset.
>
> > [ 133.875150] usb 2-1-port3: not reset yet, waiting 10ms
> > [ 133.895502] usb 2-1-port3: not reset yet, waiting 10ms
> > [ 133.918239] usb 2-1-port3: not reset yet, waiting 200ms
> > [ 134.139529] usb 2-1-port3: not reset yet, waiting 200ms
> > [ 134.365296] usb 2-1-port3: not reset yet, waiting 200ms
> > [ 134.590185] usb 2-1-port3: not reset yet, waiting 200ms
> > [ 134.641330] hub 2-1:1.0: state 7 ports 4 chg 0000 evt 0008
> > [ 134.658880] hub 2-1:1.0: hub_suspend
> > [ 134.792908] usb 2-1: usb auto-suspend, wakeup 1
> >
> > Disabling autosuspend for this hub resolves the issue.
>
> It may be possible to fix the problem. You should try that before
> giving up.
>
> Alan Stern
[ 133.120060] usb 2-1: usb wakeup-resume
[ 133.160033] usb 2-1: Waited 0ms for CONNECT
[ 133.165423] usb 2-1: finish resume
[ 133.176919] hub 2-1:1.0: hub_resume
When a USB3 device is connected to the hub, it did finish the resume
and should be put back into U0, but it seems to have failed.
On Wed, Apr 12, 2023 at 09:55:02AM +0800, Jimmy Hu wrote:
> On Tue, Apr 11, 2023 at 9:55 PM Alan Stern <[email protected]> wrote:
> >
> > On Tue, Apr 11, 2023 at 08:31:45AM +0000, Jimmy Hu wrote:
> > > The VIA VL813 USB3.0 hub appears to have an issue with autosuspend and
> > > detecting USB3 devices. This can be reproduced by connecting a USB3
> > > device to the hub after the hub enters autosuspend mode.
> > >
> > > //connect the hub
> > > [ 106.854204] usb 2-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
> > > [ 107.084993] usb 2-1: New USB device found, idVendor=2109, idProduct=0813, bcdDevice=90.15
> > > [ 107.094520] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
> > > [ 107.111836] usb 2-1: Product: USB3.0 Hub
> > > [ 107.116835] usb 2-1: Manufacturer: VIA Labs, Inc.
> > > [ 107.314230] hub 2-1:1.0: USB hub found
> > > [ 107.321356] hub 2-1:1.0: 4 ports detected
> > >
> > > //the hub enters autosuspend mode
> > > [ 107.738873] hub 2-1:1.0: hub_suspend
> > > [ 107.922097] usb 2-1: usb auto-suspend, wakeup 1
> > >
> > > //connect a USB3 device
> > > [ 133.120060] usb 2-1: usb wakeup-resume
> > > [ 133.160033] usb 2-1: Waited 0ms for CONNECT
> > > [ 133.165423] usb 2-1: finish resume
> > > [ 133.176919] hub 2-1:1.0: hub_resume
> > > [ 133.188026] usb 2-1-port3: status 0263 change 0041
> > > [ 133.323585] hub 2-1:1.0: state 7 ports 4 chg 0008 evt 0008
> > > [ 133.342423] usb 2-1-port3: link state change
> > > [ 133.358154] usb 2-1-port3: status 0263, change 0040, 5.0 Gb/s
> >
> > This status value indicates that the port is in the U3 suspend state.
> > Maybe the port needs to be put back into U0 before it can be reset.
> >
> > > [ 133.875150] usb 2-1-port3: not reset yet, waiting 10ms
> > > [ 133.895502] usb 2-1-port3: not reset yet, waiting 10ms
> > > [ 133.918239] usb 2-1-port3: not reset yet, waiting 200ms
> > > [ 134.139529] usb 2-1-port3: not reset yet, waiting 200ms
> > > [ 134.365296] usb 2-1-port3: not reset yet, waiting 200ms
> > > [ 134.590185] usb 2-1-port3: not reset yet, waiting 200ms
> > > [ 134.641330] hub 2-1:1.0: state 7 ports 4 chg 0000 evt 0008
> > > [ 134.658880] hub 2-1:1.0: hub_suspend
> > > [ 134.792908] usb 2-1: usb auto-suspend, wakeup 1
> > >
> > > Disabling autosuspend for this hub resolves the issue.
> >
> > It may be possible to fix the problem. You should try that before
> > giving up.
> >
> > Alan Stern
>
> [ 133.120060] usb 2-1: usb wakeup-resume
> [ 133.160033] usb 2-1: Waited 0ms for CONNECT
> [ 133.165423] usb 2-1: finish resume
> [ 133.176919] hub 2-1:1.0: hub_resume
> When a USB3 device is connected to the hub, it did finish the resume
> and should be put back into U0, but it seems to have failed.
Those messages mean the hub's upstream port (the port on the hub which
connects to the computer) is back in U0. But I was talking about the
downstream port (the port on the hub which connects to the device that
was just plugged in). That port is in U3.
Alan Stern