From: Alison Chaiken <[email protected]>
Add generalized support for setting arbitrary configuration of the
U-Blox Zed-F9P GNSS. Employ the new functionality to set the baud rate
of the Zed-F9P if the devicetree specifies a non-default value.
Tested with 6.1.22, only on a U-Blox Zed-F9P GNSS.
V1 -> V2 Fixes error identified by kernel test robot:
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Alison Chaiken (2):
gnss: ubx: customize serial device open to set U-Blox Zed-F9P baud
dt-bindings: gnss: Add U-Blox Zed-F9
.../bindings/gnss/u-blox,neo-6m.yaml | 1 +
drivers/gnss/ubx.c | 195 ++++++++++++++++++
2 files changed, 196 insertions(+)
base-commit: 825a0714d2b3883d4f8ff64f6933fb73ee3f1834
--
2.39.2
From: Alison Chaiken <[email protected]>
Add support for the U-Blox Zed-F9P GNSS device.
Signed-off-by: Alison Chaiken <[email protected]>
---
Documentation/devicetree/bindings/gnss/u-blox,neo-6m.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/gnss/u-blox,neo-6m.yaml b/Documentation/devicetree/bindings/gnss/u-blox,neo-6m.yaml
index 4835a280b3bf..86b65d4d9266 100644
--- a/Documentation/devicetree/bindings/gnss/u-blox,neo-6m.yaml
+++ b/Documentation/devicetree/bindings/gnss/u-blox,neo-6m.yaml
@@ -21,6 +21,7 @@ properties:
- u-blox,neo-6m
- u-blox,neo-8
- u-blox,neo-m8
+ - u-blox,zed-f9p
reg:
description: >
--
2.39.2
From: Alison Chaiken <[email protected]>
Add support for setting the baud rate of U-Blox Zed-F9P GNSS devices.
Provide functions that support writing of arbitrary configuration
messages to the device plus one that specifically configures the baud
rate. Override the default gnss_serial_open() with a new method that
writes the configuration message to the GNSS if the devicetree declares
it to be a Zed F9P and requests a non-default baud. Add a boolean flag
to the ubx_data private data of the GNSS driver in order to track
whether the configuration message has already been written. Set the Zed
F9P to its default port speed if the devicetree does not specify a
value.
Signed-off-by: Alison Chaiken <[email protected]>
---
V1 -> V2 Fixes error identified by kernel test robot:
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
drivers/gnss/ubx.c | 195 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 195 insertions(+)
diff --git a/drivers/gnss/ubx.c b/drivers/gnss/ubx.c
index c951be202ca2..1d59a11f5360 100644
--- a/drivers/gnss/ubx.c
+++ b/drivers/gnss/ubx.c
@@ -9,18 +9,201 @@
#include <linux/gnss.h>
#include <linux/init.h>
#include <linux/kernel.h>
+#include <linux/kstrtox.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
#include <linux/regulator/consumer.h>
#include <linux/serdev.h>
#include "serial.h"
+/* Total configuration message length = PREAMBLE_LEN + MESSAGE_CLASS_LEN +
+ * MESSAGE_LENGTH_LEN + payload length + CHECKSUM_LEN
+ */
+const int32_t PREAMBLE_LEN = 2;
+const int32_t MESSAGE_CLASS_LEN = 2;
+const int32_t MESSAGE_LENGTH_LEN = 2;
+const int32_t CHECKSUM_LEN = 2;
+const size_t FIRST_CONFIG_REGISTER_BYTE = 10U;
+const size_t FIRST_VALUE_BYTE = 14U;
+const size_t FIRST_CHECKSUM_BYTE = 18U;
+const size_t CFG_MSG_TOTAL_LEN = 20U;
+
+uint8_t ZED_F9P_CFG_VALSET_MSG[] = {
+ 0xB5, 0x62, /* 0-1 preamble */
+ 0x06, 0x8A, /* 2-3 CFG_VALSET command */
+ 0x0C, 0x00, /* 4-5 payload length = 12 for one key-value pair */
+ 0x00, /* 6 U-Blox API version */
+ 0x01, /* 7 Write to RAM */
+ 0x00, 0x00, /* 8-9 Reserved */
+ 0x00, 0x00, 0x00, 0x00, /* 10-13 Placeholder for configuration register */
+ 0x00, 0x00, 0x00, 0x00, /* 14-17 Placeholder for baud value */
+ 0x00, 0x00 /* 18-19 Placeholder for checksum */
+};
+
+const speed_t ZED_F9P_MIN_BAUD = 9600;
+const speed_t ZED_F9P_DEFAULT_BAUD = 38400;
+const speed_t ZED_F9P_MAX_BAUD = 921600;
+const uint32_t ZED_F9P_BAUD_CONFIG_REGISTER = 0x40520001;
+
struct ubx_data {
struct regulator *v_bckp;
struct regulator *vcc;
+ unsigned long is_configured;
+};
+
+union message_length {
+ uint16_t ml;
+ uint8_t bytes[2];
+};
+
+union int_to_bytes {
+ uint32_t int_val;
+ uint8_t bytes[4];
};
+/* Payload length is contained in bytes 0-2 after message class and ID.
+ * While the checksum includes the Message class and ID plus message length, the
+ * payload does not.
+ */
+static uint16_t get_payload_length(const uint8_t msg[])
+{
+ union message_length hs_msg_len;
+
+ hs_msg_len.bytes[0] = msg[PREAMBLE_LEN + MESSAGE_CLASS_LEN];
+ hs_msg_len.bytes[1] = msg[PREAMBLE_LEN + MESSAGE_CLASS_LEN + 1U];
+ return hs_msg_len.ml;
+}
+
+static int32_t get_msg_total_len(const uint8_t msg[])
+{
+ const size_t payload_len = get_payload_length(msg);
+
+ return PREAMBLE_LEN + MESSAGE_CLASS_LEN + MESSAGE_LENGTH_LEN + payload_len
+ + CHECKSUM_LEN;
+}
+
+/* The checksum is calculated on message class, message ID, message length and
+ * payload.
+ */
+static void calc_ubx_checksum(const uint8_t msg[], uint8_t checksum[],
+ const uint16_t total_len)
+{
+ uint8_t CK_A = 0;
+ uint8_t CK_B = 0;
+ int i;
+
+ for (i = PREAMBLE_LEN; i < (total_len - CHECKSUM_LEN); i++) {
+ CK_A += msg[i];
+ CK_B += CK_A;
+ }
+ checksum[0] = CK_A;
+ checksum[1] = CK_B;
+}
+
+static uint32_t check_baud(speed_t speed, const struct device *dev)
+{
+ if ((speed < ZED_F9P_MIN_BAUD) || (speed > ZED_F9P_MAX_BAUD)) {
+ dev_warn(dev, "Baud rate specification %d out of range\n", speed);
+ speed = ZED_F9P_DEFAULT_BAUD;
+ }
+ return speed;
+}
+
+static int prepare_zedf9p_config_msg(const speed_t speed,
+ const struct device *dev, const size_t msg_register)
+{
+ union int_to_bytes cfg_val, cfg_register;
+ int i = 0;
+ uint8_t checksum[2];
+ const size_t total_len = get_msg_total_len(ZED_F9P_CFG_VALSET_MSG);
+
+ if (total_len != CFG_MSG_TOTAL_LEN)
+ goto bad_msg;
+
+ cfg_val.int_val = check_baud(speed, dev);
+ cfg_register.int_val = msg_register;
+ for (i = 0; i < 4; i++) {
+ ZED_F9P_CFG_VALSET_MSG[FIRST_VALUE_BYTE + i] = cfg_val.bytes[i];
+ ZED_F9P_CFG_VALSET_MSG[FIRST_CONFIG_REGISTER_BYTE + i] = cfg_register.bytes[i];
+ }
+ calc_ubx_checksum(ZED_F9P_CFG_VALSET_MSG, checksum, total_len);
+ ZED_F9P_CFG_VALSET_MSG[FIRST_CHECKSUM_BYTE] = checksum[0];
+ ZED_F9P_CFG_VALSET_MSG[FIRST_CHECKSUM_BYTE + 1U] = checksum[1];
+ return 0;
+
+ bad_msg:
+ dev_err(dev, "Malformed UBX-CFG-VALSET message\n");
+ return -EINVAL;
+}
+
+/* Configure the Zed F9P baud rate via the UBX-CFG-VALSET message. */
+static int set_zedf9p_baud(struct gnss_device *gdev,
+ struct serdev_device *serdev, const speed_t speed)
+{
+ size_t count = 0U;
+ int ret;
+
+ if (speed == ZED_F9P_DEFAULT_BAUD)
+ return 0;
+
+ ret = prepare_zedf9p_config_msg(speed, &gdev->dev, ZED_F9P_BAUD_CONFIG_REGISTER);
+ if (ret)
+ return ret;
+ /* Initially set the UART to the default speed to match the GNSS' power-on value. */
+ serdev_device_set_baudrate(serdev, ZED_F9P_DEFAULT_BAUD);
+ /* Now set the new baud rate. */
+ count = gdev->ops->write_raw(gdev, ZED_F9P_CFG_VALSET_MSG, CFG_MSG_TOTAL_LEN);
+ if (count != CFG_MSG_TOTAL_LEN)
+ return count;
+
+ return 0;
+}
+
+static int ubx_serial_open(struct gnss_device *gdev)
+{
+ struct gnss_serial *gserial = gnss_get_drvdata(gdev);
+ struct serdev_device *serdev = gserial->serdev;
+ struct ubx_data *data = gnss_serial_get_drvdata(gserial);
+ struct device_node *np;
+ int ret;
+
+ ret = serdev_device_open(serdev);
+ if (ret)
+ return ret;
+
+ serdev_device_set_flow_control(serdev, false);
+
+ np = serdev->dev.of_node;
+ if ((of_device_is_compatible(np, "u-blox,zed-f9p")) && (!data->is_configured)) {
+ /* 4800 is the default value set by gnss_serial_parse_dt() */
+ if (gserial->speed == 4800) {
+ /* Fall back instead to Zed F9P default */
+ gserial->speed = ZED_F9P_DEFAULT_BAUD;
+ } else {
+ ret = set_zedf9p_baud(gdev, serdev, gserial->speed);
+ if (ret)
+ return ret;
+ }
+ data->is_configured = 1;
+ }
+ serdev_device_set_baudrate(serdev, gserial->speed);
+
+ ret = pm_runtime_get_sync(&serdev->dev);
+ if (ret < 0) {
+ pm_runtime_put_noidle(&serdev->dev);
+ goto err_close;
+ }
+ return 0;
+
+err_close:
+ serdev_device_close(serdev);
+
+ return ret;
+}
+
static int ubx_set_active(struct gnss_serial *gserial)
{
struct ubx_data *data = gnss_serial_get_drvdata(gserial);
@@ -67,6 +250,7 @@ static int ubx_probe(struct serdev_device *serdev)
{
struct gnss_serial *gserial;
struct ubx_data *data;
+ struct gnss_operations *ubx_gnss_ops;
int ret;
gserial = gnss_serial_allocate(serdev, sizeof(*data));
@@ -74,12 +258,22 @@ static int ubx_probe(struct serdev_device *serdev)
ret = PTR_ERR(gserial);
return ret;
}
+ ubx_gnss_ops = kzalloc(sizeof(struct gnss_operations), GFP_KERNEL);
+ if (IS_ERR(ubx_gnss_ops)) {
+ ret = PTR_ERR(ubx_gnss_ops);
+ return ret;
+ }
gserial->ops = &ubx_gserial_ops;
gserial->gdev->type = GNSS_TYPE_UBX;
+ ubx_gnss_ops->open = &ubx_serial_open;
+ ubx_gnss_ops->close = gserial->gdev->ops->close;
+ ubx_gnss_ops->write_raw = gserial->gdev->ops->write_raw;
+ gserial->gdev->ops = ubx_gnss_ops;
data = gnss_serial_get_drvdata(gserial);
+ data->is_configured = 0;
data->vcc = devm_regulator_get(&serdev->dev, "vcc");
if (IS_ERR(data->vcc)) {
@@ -133,6 +327,7 @@ static const struct of_device_id ubx_of_match[] = {
{ .compatible = "u-blox,neo-6m" },
{ .compatible = "u-blox,neo-8" },
{ .compatible = "u-blox,neo-m8" },
+ { .compatible = "u-blox,zed-f9p" },
{},
};
MODULE_DEVICE_TABLE(of, ubx_of_match);
--
2.39.2
On 30/04/2023 19:48, [email protected] wrote:
> From: Alison Chaiken <[email protected]>
>
> Add support for the U-Blox Zed-F9P GNSS device.
>
> Signed-off-by: Alison Chaiken <[email protected]>
No improvements, so the same comment:
Please use scripts/get_maintainers.pl to get a list of necessary people
and lists to CC. It might happen, that command when run on an older
kernel, gives you outdated entries. Therefore please be sure you base
your patches on recent Linux kernel.
You missed at least DT list (maybe more), so this won't be tested.
Please resend without skipping necessary entries.
Best regards,
Krzysztof