2023-05-27 23:55:25

by Shenghao Ding

[permalink] [raw]
Subject: [PATCH v4 5/6] ALSA: hda/tas2781: Add tas2781 HDA driver

Create tas2781 HDA driver.

Signed-off-by: Shenghao Ding <[email protected]>

---
Changes in v4:
- Add [email protected] into Cc list
- remove unused ret in tas2781_hda_playback
- in all *__put function, return 0, if the value is unchanged
- remove superfluous
- rewrite the subid judgement
- dev_info to dev_dbg
Changes to be committed:
modified: sound/pci/hda/Kconfig
modified: sound/pci/hda/Makefile
new file: sound/pci/hda/tas2781_hda_i2c.c
---
sound/pci/hda/Kconfig | 15 +
sound/pci/hda/Makefile | 2 +
sound/pci/hda/tas2781_hda_i2c.c | 834 ++++++++++++++++++++++++++++++++
3 files changed, 851 insertions(+)
create mode 100644 sound/pci/hda/tas2781_hda_i2c.c

diff --git a/sound/pci/hda/Kconfig b/sound/pci/hda/Kconfig
index 886255a03e8b..e66257277492 100644
--- a/sound/pci/hda/Kconfig
+++ b/sound/pci/hda/Kconfig
@@ -130,6 +130,21 @@ config SND_HDA_SCODEC_CS35L41_SPI
comment "Set to Y if you want auto-loading the side codec driver"
depends on SND_HDA=y && SND_HDA_SCODEC_CS35L41_SPI=m

+config SND_HDA_SCODEC_TAS2781_I2C
+ tristate "Build TAS2781 HD-audio side codec support for I2C Bus"
+ depends on I2C
+ depends on ACPI
+ depends on SND_SOC
+ select SND_SOC_TAS2781_COMLIB
+ select SND_SOC_TAS2781_FMWLIB
+ select CRC32_SARWATE
+ help
+ Say Y or M here to include TAS2781 I2C HD-audio side codec support
+ in snd-hda-intel driver, such as ALC287.
+
+comment "Set to Y if you want auto-loading the side codec driver"
+ depends on SND_HDA=y && SND_HDA_SCODEC_TAS2781_I2C=m
+
config SND_HDA_CODEC_REALTEK
tristate "Build Realtek HD-audio codec support"
select SND_HDA_GENERIC
diff --git a/sound/pci/hda/Makefile b/sound/pci/hda/Makefile
index 00d306104484..1c76609690d6 100644
--- a/sound/pci/hda/Makefile
+++ b/sound/pci/hda/Makefile
@@ -32,6 +32,7 @@ snd-hda-scodec-cs35l41-objs := cs35l41_hda.o
snd-hda-scodec-cs35l41-i2c-objs := cs35l41_hda_i2c.o
snd-hda-scodec-cs35l41-spi-objs := cs35l41_hda_spi.o
snd-hda-cs-dsp-ctls-objs := hda_cs_dsp_ctl.o
+snd-hda-scodec-tas2781-i2c-objs := tas2781_hda_i2c.o

# common driver
obj-$(CONFIG_SND_HDA) := snd-hda-codec.o
@@ -56,6 +57,7 @@ obj-$(CONFIG_SND_HDA_SCODEC_CS35L41) += snd-hda-scodec-cs35l41.o
obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_I2C) += snd-hda-scodec-cs35l41-i2c.o
obj-$(CONFIG_SND_HDA_SCODEC_CS35L41_SPI) += snd-hda-scodec-cs35l41-spi.o
obj-$(CONFIG_SND_HDA_CS_DSP_CONTROLS) += snd-hda-cs-dsp-ctls.o
+obj-$(CONFIG_SND_HDA_SCODEC_TAS2781_I2C) += snd-hda-scodec-tas2781-i2c.o

# this must be the last entry after codec drivers;
# otherwise the codec patches won't be hooked before the PCI probe
diff --git a/sound/pci/hda/tas2781_hda_i2c.c b/sound/pci/hda/tas2781_hda_i2c.c
new file mode 100644
index 000000000000..e124575d3737
--- /dev/null
+++ b/sound/pci/hda/tas2781_hda_i2c.c
@@ -0,0 +1,834 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// TAS2781 HDA I2C driver
+//
+// Copyright 2023 Texas Instruments, Inc.
+//
+// Author: Shenghao Ding <[email protected]>
+
+#include <linux/acpi.h>
+#include <linux/crc8.h>
+#include <linux/crc32.h>
+#include <linux/efi.h>
+#include <linux/firmware.h>
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <sound/hda_codec.h>
+#include <sound/soc.h>
+#include <sound/tas2781.h>
+#include <sound/tlv.h>
+#include <sound/tas2781-tlv.h>
+
+#include "hda_local.h"
+#include "hda_auto_parser.h"
+#include "hda_component.h"
+#include "hda_jack.h"
+#include "hda_generic.h"
+
+#define TASDEVICE_SPEAKER_CALIBRATION_SIZE 20
+
+#define ACARD_SINGLE_RANGE_EXT_TLV(xname, xreg, xshift, xmin, xmax, xinvert, \
+ xhandler_get, xhandler_put, tlv_array) \
+{ .iface = SNDRV_CTL_ELEM_IFACE_CARD, .name = (xname),\
+ .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ |\
+ SNDRV_CTL_ELEM_ACCESS_READWRITE,\
+ .tlv.p = (tlv_array), \
+ .info = snd_soc_info_volsw_range, \
+ .get = xhandler_get, .put = xhandler_put, \
+ .private_value = (unsigned long)&(struct soc_mixer_control) \
+ {.reg = xreg, .rreg = xreg, .shift = xshift, \
+ .rshift = xshift, .min = xmin, .max = xmax, \
+ .invert = xinvert} }
+
+enum calib_data {
+ R0_VAL = 0,
+ INV_R0,
+ R0LOW,
+ POWER,
+ TLIM,
+ CALIB_MAX
+};
+
+static int tas2781_acpi_get_i2c_resource(struct acpi_resource
+ *ares, void *data)
+{
+ struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)data;
+ struct acpi_resource_i2c_serialbus *sb;
+
+ if (i2c_acpi_get_i2c_resource(ares, &sb)) {
+ if (sb->slave_address != TAS2781_GLOBAL_ADDR) {
+ tas_priv->tasdevice[tas_priv->ndev].dev_addr =
+ (unsigned int)sb->slave_address;
+ tas_priv->ndev++;
+ } else
+ tas_priv->glb_addr.dev_addr = TAS2781_GLOBAL_ADDR;
+
+ }
+
+ return 1;
+}
+
+static int tas2781_hda_read_acpi(struct tasdevice_priv *tas_priv,
+ const char *hid)
+{
+ struct acpi_device *adev;
+ struct device *physdev;
+ LIST_HEAD(resources);
+ const char *sub;
+ int ret;
+
+ adev = acpi_dev_get_first_match_dev(hid, NULL, -1);
+ if (!adev) {
+ dev_err(tas_priv->dev,
+ "Failed to find an ACPI device for %s\n", hid);
+ return -ENODEV;
+ }
+ strcpy(tas_priv->dev_name, hid);
+ physdev = get_device(acpi_get_first_physical_node(adev));
+ acpi_dev_put(adev);
+
+ sub = acpi_get_subsystem_id(ACPI_HANDLE(physdev));
+ if (IS_ERR(sub))
+ sub = NULL;
+ dev_info(tas_priv->dev, "subid = %s\n", sub);
+
+ tas_priv->acpi_subsystem_id = sub;
+
+ ret = acpi_dev_get_resources(adev, &resources,
+ tas2781_acpi_get_i2c_resource, tas_priv);
+ if (ret < 0)
+ goto err;
+ acpi_dev_free_resource_list(&resources);
+
+ put_device(physdev);
+ dev_info(tas_priv->dev, "global addr: 0x%02x devcnt = %d\n",
+ tas_priv->glb_addr.dev_addr, tas_priv->ndev);
+
+ return 0;
+
+err:
+ dev_err(tas_priv->dev, "Failed acpi ret: %d\n", ret);
+ put_device(physdev);
+
+ return ret;
+}
+
+static void tas2781_hda_playback_hook(struct device *dev, int action)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+
+ dev_dbg(tas_priv->dev, "%s: action = %d\n", __func__, action);
+ switch (action) {
+ case HDA_GEN_PCM_ACT_OPEN:
+ pm_runtime_get_sync(dev);
+ mutex_lock(&tas_priv->codec_lock);
+ tas_priv->cur_conf = 0;
+ tas_priv->rcabin.profile_cfg_id = 1;
+ tasdevice_tuning_switch(tas_priv, 0);
+ mutex_unlock(&tas_priv->codec_lock);
+ break;
+ case HDA_GEN_PCM_ACT_CLOSE:
+ mutex_lock(&tas_priv->codec_lock);
+ tasdevice_tuning_switch(tas_priv, 1);
+ mutex_unlock(&tas_priv->codec_lock);
+
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+ break;
+ default:
+ dev_warn(tas_priv->dev, "Playback action not supported: %d\n",
+ action);
+ break;
+ }
+}
+
+static int tasdevice_info_profile(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_priv->rcabin.ncfgs - 1;
+
+ return 0;
+}
+
+static int tasdevice_get_profile_id(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->rcabin.profile_cfg_id;
+
+ return 0;
+}
+
+static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ int ret = 0;
+
+ if (tas_priv->rcabin.profile_cfg_id !=
+ ucontrol->value.integer.value[0]) {
+ tas_priv->rcabin.profile_cfg_id =
+ ucontrol->value.integer.value[0];
+ ret = 0;
+ }
+
+ return ret;
+}
+
+static int tasdevice_create_control(struct tasdevice_priv *tas_priv)
+{
+ char prof_ctrl_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN];
+ struct hda_codec *codec = tas_priv->codec;
+ struct snd_kcontrol_new prof_ctrl = {
+ .name = prof_ctrl_name,
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_profile,
+ .get = tasdevice_get_profile_id,
+ .put = tasdevice_set_profile_id,
+ };
+ int ret;
+
+ /* Create a mixer item for selecting the active profile */
+ scnprintf(prof_ctrl_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN,
+ "spk-profile-id");
+ ret = snd_ctl_add(codec->card, snd_ctl_new1(&prof_ctrl, tas_priv));
+ if (ret) {
+ dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n",
+ prof_ctrl.name, ret);
+ goto out;
+ }
+
+ dev_dbg(tas_priv->dev, "Added Control %s\n", prof_ctrl.name);
+
+out:
+ return ret;
+}
+
+static int tasdevice_info_programs(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct tasdevice_fw *tas_fw = tas_priv->fmw;
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_fw->nr_programs;
+
+ return 0;
+}
+
+static int tasdevice_info_configurations(
+ struct snd_kcontrol *kcontrol, struct snd_ctl_elem_info *uinfo)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct tasdevice_fw *tas_fw = tas_priv->fmw;
+
+ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
+ uinfo->count = 1;
+ uinfo->value.integer.min = 0;
+ uinfo->value.integer.max = tas_fw->nr_configurations - 1;
+
+ return 0;
+}
+
+static int tasdevice_program_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->cur_prog;
+
+ return 0;
+}
+
+static int tasdevice_program_put(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ unsigned int nr_program = ucontrol->value.integer.value[0];
+ int ret = 0;
+
+ if (tas_priv->cur_prog != nr_program) {
+ tas_priv->cur_prog = nr_program;
+ ret = 1;
+ }
+
+ return ret;
+}
+
+static int tasdevice_config_get(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+
+ ucontrol->value.integer.value[0] = tas_priv->cur_conf;
+
+ return 0;
+}
+
+static int tasdevice_config_put(
+ struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ unsigned int nr_configuration = ucontrol->value.integer.value[0];
+ int ret = 0;
+
+ if (tas_priv->cur_conf != nr_configuration) {
+ tas_priv->cur_conf = nr_configuration;
+ ret = 1;
+ }
+
+ return ret;
+}
+
+/*
+ * tas2781_digital_getvol - get the volum control
+ * @kcontrol: control pointer
+ * @ucontrol: User data
+ * Customer Kcontrol for tas2781 is primarily for regmap booking, paging
+ * depends on internal regmap mechanism.
+ * tas2781 contains book and page two-level register map, especially
+ * book switching will set the register BXXP00R7F, after switching to the
+ * correct book, then leverage the mechanism for paging to access the
+ * register.
+ */
+static int tas2781_digital_getvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_digital_getvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_amp_getvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_amp_getvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_digital_putvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_digital_putvol(tas_priv, ucontrol, mc);
+}
+
+static int tas2781_amp_putvol(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
+ struct soc_mixer_control *mc =
+ (struct soc_mixer_control *)kcontrol->private_value;
+
+ return tasdevice_amp_putvol(tas_priv, ucontrol, mc);
+}
+
+static const struct snd_kcontrol_new tas2781_snd_controls[] = {
+ ACARD_SINGLE_RANGE_EXT_TLV("Amp Gain Volume", TAS2781_AMP_LEVEL,
+ 1, 0, 20, 0, tas2781_amp_getvol,
+ tas2781_amp_putvol, amp_vol_tlv),
+ ACARD_SINGLE_RANGE_EXT_TLV("Digital Volume", TAS2781_DVC_LVL,
+ 0, 0, 200, 1, tas2781_digital_getvol,
+ tas2781_digital_putvol, dvc_tlv),
+};
+
+static int tasdevice_dsp_create_ctrls(struct tasdevice_priv
+ *tas_priv)
+{
+ char prog_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN];
+ char conf_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN];
+ struct hda_codec *codec = tas_priv->codec;
+ struct snd_kcontrol_new prog_ctl = {
+ .name = prog_name,
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_programs,
+ .get = tasdevice_program_get,
+ .put = tasdevice_program_put,
+ };
+ struct snd_kcontrol_new conf_ctl = {
+ .name = conf_name,
+ .iface = SNDRV_CTL_ELEM_IFACE_CARD,
+ .info = tasdevice_info_configurations,
+ .get = tasdevice_config_get,
+ .put = tasdevice_config_put,
+ };
+ int ret;
+
+ scnprintf(prog_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "spk-prog-id");
+ scnprintf(conf_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "spk-conf-id");
+
+ ret = snd_ctl_add(codec->card, snd_ctl_new1(&prog_ctl, tas_priv));
+ if (ret) {
+ dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n",
+ prog_ctl.name, ret);
+ goto out;
+ }
+
+ dev_dbg(tas_priv->dev, "Added Control %s\n", prog_ctl.name);
+
+ ret = snd_ctl_add(codec->card, snd_ctl_new1(&conf_ctl, tas_priv));
+ if (ret) {
+ dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n",
+ conf_ctl.name, ret);
+ goto out;
+ }
+
+ dev_dbg(tas_priv->dev, "Added Control %s\n", conf_ctl.name);
+out:
+ return ret;
+}
+
+static void tas2781_apply_calib(struct tasdevice_priv *tas_priv)
+{
+ static const unsigned char page_array[CALIB_MAX] = {
+ 0x17, 0x18, 0x18, 0x0d, 0x18
+ };
+ static const unsigned char rgno_array[CALIB_MAX] = {
+ 0x74, 0x0c, 0x14, 0x3c, 0x7c
+ };
+ unsigned char *data;
+ int i, j, rc;
+
+ for (i = 0; i < tas_priv->ndev; i++) {
+ data = tas_priv->cali_data.data +
+ i * TASDEVICE_SPEAKER_CALIBRATION_SIZE;
+ for (j = 0; j < CALIB_MAX; j++) {
+ rc = tasdevice_dev_bulk_write(tas_priv, i,
+ TASDEVICE_REG(0, page_array[j], rgno_array[j]),
+ &(data[4 * j]), 4);
+ if (rc < 0)
+ dev_err(tas_priv->dev,
+ "chn %d calib %d bulk_wr err = %d\n",
+ i, j, rc);
+ }
+ }
+}
+
+static int tas2781_save_calibration(struct tasdevice_priv *tas_priv)
+{
+ efi_guid_t efi_guid = EFI_GUID(0x02f9af02, 0x7734, 0x4233, 0xb4, 0x3d,
+ 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3);
+ static efi_char16_t efi_name[] = L"CALI_DATA";
+ struct tm *tm = &tas_priv->tm;
+ unsigned int attr, crc;
+ unsigned int *tmp_val;
+ efi_status_t status;
+ int ret = 0;
+
+ //Lenovo devices
+ if (tas_priv->catlog_id == LENOVO)
+ efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc, 0x09,
+ 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92);
+
+ tas_priv->cali_data.total_sz = 0;
+ /* Get real size of UEFI variable */
+ status = efi.get_variable(efi_name, &efi_guid, &attr,
+ &tas_priv->cali_data.total_sz, tas_priv->cali_data.data);
+ if (status == EFI_BUFFER_TOO_SMALL) {
+ ret = -ENODEV;
+ /* Allocate data buffer of data_size bytes */
+ tas_priv->cali_data.data = devm_kzalloc(tas_priv->dev,
+ tas_priv->cali_data.total_sz, GFP_KERNEL);
+ if (!tas_priv->cali_data.data)
+ return -ENOMEM;
+ /* Get variable contents into buffer */
+ status = efi.get_variable(efi_name, &efi_guid, &attr,
+ &tas_priv->cali_data.total_sz,
+ tas_priv->cali_data.data);
+ if (status != EFI_SUCCESS) {
+ ret = -EINVAL;
+ goto out;
+ }
+ }
+
+ tmp_val = (unsigned int *)tas_priv->cali_data.data;
+
+ crc = crc32(~0, tas_priv->cali_data.data, 84) ^ ~0;
+ dev_dbg(tas_priv->dev, "cali crc 0x%08x PK tmp_val 0x%08x\n",
+ crc, tmp_val[21]);
+
+ if (crc == tmp_val[21]) {
+ time64_to_tm(tmp_val[20], 0, tm);
+ dev_dbg(tas_priv->dev, "%4ld-%2d-%2d, %2d:%2d:%2d\n",
+ tm->tm_year, tm->tm_mon, tm->tm_mday,
+ tm->tm_hour, tm->tm_min, tm->tm_sec);
+ tas2781_apply_calib(tas_priv);
+ }
+out:
+ return ret;
+}
+
+static void tasdevice_fw_ready(const struct firmware *fmw,
+ void *context)
+{
+ struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context;
+ struct hda_codec *codec = tas_priv->codec;
+ int i, ret = 0;
+
+ pm_runtime_get_sync(tas_priv->dev);
+ mutex_lock(&tas_priv->codec_lock);
+
+ ret = tasdevice_rca_parser(tas_priv, fmw);
+ if (ret)
+ goto out;
+ tasdevice_create_control(tas_priv);
+
+ for (i = 0; i < ARRAY_SIZE(tas2781_snd_controls); i++) {
+ ret = snd_ctl_add(codec->card,
+ snd_ctl_new1(&tas2781_snd_controls[i], tas_priv));
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to add KControl %s = %d\n",
+ tas2781_snd_controls[i].name, ret);
+ goto out;
+ }
+ }
+
+ tasdevice_dsp_remove(tas_priv);
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING;
+ scnprintf(tas_priv->coef_binaryname, 64, "TAS2XXX%04X.bin",
+ codec->core.subsystem_id & 0xffff);
+ ret = tasdevice_dsp_parser(tas_priv);
+ if (ret) {
+ dev_err(tas_priv->dev, "dspfw load %s error\n",
+ tas_priv->coef_binaryname);
+ tas_priv->fw_state = TASDEVICE_DSP_FW_FAIL;
+ goto out;
+ }
+ tasdevice_dsp_create_ctrls(tas_priv);
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_ALL_OK;
+ tasdevice_prmg_load(tas_priv, 0);
+ tas_priv->cur_prog = 0;
+
+ /* If calibrated data occurs error, dsp will still works with default
+ * calibrated data inside algo.
+ */
+ tas2781_save_calibration(tas_priv);
+
+out:
+ if (tas_priv->fw_state == TASDEVICE_DSP_FW_FAIL) {
+ /*If DSP FW fail, kcontrol won't be created */
+ tasdevice_config_info_remove(tas_priv);
+ tasdevice_dsp_remove(tas_priv);
+ }
+ mutex_unlock(&tas_priv->codec_lock);
+ if (fmw)
+ release_firmware(fmw);
+ pm_runtime_mark_last_busy(tas_priv->dev);
+ pm_runtime_put_autosuspend(tas_priv->dev);
+}
+
+static int tas2781_hda_bind(struct device *dev, struct device *master,
+ void *master_data)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ struct hda_component *comps = master_data;
+ struct hda_codec *codec;
+ unsigned int subid;
+ int ret;
+
+ if (!comps || tas_priv->index < 0 ||
+ tas_priv->index >= HDA_MAX_COMPONENTS)
+ return -EINVAL;
+
+ comps = &comps[tas_priv->index];
+ if (comps->dev)
+ return -EBUSY;
+
+ codec = comps->codec;
+ subid = codec->core.subsystem_id & 0xFFFF;
+
+ //Lenovo devices
+ if ((subid == 0x387d) || (subid == 0x387e) || (subid == 0x3881)
+ || (subid == 0x3884) || (subid == 0x3886) || (subid == 0x38a7)
+ || (subid == 0x38a8) || (subid == 0x38ba) || (subid == 0x38bb)
+ || (subid == 0x38be) || (subid == 0x38bf) || (subid == 0x38c3)
+ || (subid == 0x38cb) || (subid == 0x38cd))
+ tas_priv->catlog_id = LENOVO;
+ else
+ tas_priv->catlog_id = OTHERS;
+
+ pm_runtime_get_sync(dev);
+
+ comps->dev = dev;
+
+ strscpy(comps->name, dev_name(dev), sizeof(comps->name));
+
+ ret = tascodec_init(tas_priv, codec, tasdevice_fw_ready);
+ if (ret)
+ return ret;
+
+ comps->playback_hook = tas2781_hda_playback_hook;
+
+ pm_runtime_mark_last_busy(dev);
+ pm_runtime_put_autosuspend(dev);
+
+ return 0;
+}
+
+static void tas2781_hda_unbind(struct device *dev,
+ struct device *master, void *master_data)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ struct hda_component *comps = master_data;
+
+ if (comps[tas_priv->index].dev == dev)
+ memset(&comps[tas_priv->index], 0, sizeof(*comps));
+
+ tasdevice_config_info_remove(tas_priv);
+ tasdevice_dsp_remove(tas_priv);
+
+ tas_priv->fw_state = TASDEVICE_DSP_FW_PENDING;
+}
+
+static const struct component_ops tas2781_hda_comp_ops = {
+ .bind = tas2781_hda_bind,
+ .unbind = tas2781_hda_unbind,
+};
+
+static void tas2781_hda_remove(struct device *dev)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+
+ pm_runtime_get_sync(tas_priv->dev);
+ pm_runtime_disable(tas_priv->dev);
+
+
+ component_del(tas_priv->dev, &tas2781_hda_comp_ops);
+
+ pm_runtime_put_noidle(tas_priv->dev);
+
+ tasdevice_remove(tas_priv);
+}
+
+static int tas2781_hda_i2c_probe(struct i2c_client *clt)
+{
+ struct tasdevice_priv *tas_priv;
+ const char *device_name;
+ int ret;
+
+ if (strstr(dev_name(&clt->dev), "TIAS2781"))
+ device_name = "TIAS2781";
+ else
+ return -ENODEV;
+
+ tas_priv = tasdevice_kzalloc(clt);
+ if (!tas_priv)
+ return -ENOMEM;
+
+ tas_priv->irq_info.irq = clt->irq;
+ ret = tas2781_hda_read_acpi(tas_priv, device_name);
+ if (ret)
+ return dev_err_probe(tas_priv->dev, ret,
+ "Platform not supported\n");
+
+ ret = tasdevice_init(tas_priv);
+ if (ret)
+ goto err;
+
+ pm_runtime_set_autosuspend_delay(tas_priv->dev, 3000);
+ pm_runtime_use_autosuspend(tas_priv->dev);
+ pm_runtime_mark_last_busy(tas_priv->dev);
+ pm_runtime_set_active(tas_priv->dev);
+ pm_runtime_get_noresume(tas_priv->dev);
+ pm_runtime_enable(tas_priv->dev);
+
+ pm_runtime_put_autosuspend(tas_priv->dev);
+
+ ret = component_add(tas_priv->dev, &tas2781_hda_comp_ops);
+ if (ret) {
+ dev_err(tas_priv->dev, "Register component failed: %d\n", ret);
+ pm_runtime_disable(tas_priv->dev);
+ }
+
+err:
+ if (ret)
+ tas2781_hda_remove(&clt->dev);
+ return ret;
+}
+
+static void tas2781_hda_i2c_remove(struct i2c_client *clt)
+{
+ tas2781_hda_remove(&clt->dev);
+}
+
+static int tas2781_runtime_suspend(struct device *dev)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ int i;
+
+ dev_info(tas_priv->dev, "Runtime Suspend\n");
+
+ mutex_lock(&tas_priv->codec_lock);
+
+ if (tas_priv->playback_started) {
+ tasdevice_tuning_switch(tas_priv, 1);
+ tas_priv->playback_started = false;
+ }
+
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+
+ for (i = 0; i < tas_priv->ndev; i++) {
+ tas_priv->tasdevice[i].cur_book = -1;
+ tas_priv->tasdevice[i].cur_prog = -1;
+ tas_priv->tasdevice[i].cur_conf = -1;
+ }
+
+ regcache_cache_only(tas_priv->regmap, true);
+ regcache_mark_dirty(tas_priv->regmap);
+
+ mutex_unlock(&tas_priv->codec_lock);
+
+ return 0;
+}
+
+static int tas2781_runtime_resume(struct device *dev)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ unsigned long calib_data_sz =
+ tas_priv->ndev * TASDEVICE_SPEAKER_CALIBRATION_SIZE;
+ int ret;
+
+ dev_info(tas_priv->dev, "Runtime Resume\n");
+
+ mutex_lock(&tas_priv->codec_lock);
+
+ regcache_cache_only(tas_priv->regmap, false);
+ ret = regcache_sync(tas_priv->regmap);
+ if (ret) {
+ dev_err(tas_priv->dev,
+ "Failed to restore register cache: %d\n", ret);
+ goto out;
+ }
+
+ tasdevice_prmg_load(tas_priv, 0);
+ tas_priv->cur_prog = 0;
+
+ /* If calibrated data occurs error, dsp will still works with default
+ * calibrated data inside algo.
+ */
+ if (tas_priv->cali_data.total_sz > calib_data_sz)
+ tas2781_apply_calib(tas_priv);
+
+out:
+ mutex_unlock(&tas_priv->codec_lock);
+
+ return ret;
+}
+
+static int tas2781_system_suspend(struct device *dev)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ int ret;
+
+ dev_dbg(tas_priv->dev, "System Suspend\n");
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ return ret;
+
+ /* Shutdown chip before system suspend */
+ regcache_cache_only(tas_priv->regmap, false);
+ tasdevice_tuning_switch(tas_priv, 1);
+ regcache_cache_only(tas_priv->regmap, true);
+ regcache_mark_dirty(tas_priv->regmap);
+ /*
+ * Reset GPIO may be shared, so cannot reset here.
+ * However beyond this point, amps may be powered down.
+ */
+ return 0;
+}
+
+static int tas2781_system_resume(struct device *dev)
+{
+ struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
+ unsigned long calib_data_sz =
+ tas_priv->ndev * TASDEVICE_SPEAKER_CALIBRATION_SIZE;
+ int i, ret;
+
+ dev_dbg(tas_priv->dev, "System Resume\n");
+
+ ret = pm_runtime_force_resume(dev);
+ if (ret)
+ return ret;
+
+ mutex_lock(&tas_priv->codec_lock);
+ tas_priv->cur_prog = -1;
+ tas_priv->cur_conf = -1;
+
+ for (i = 0; i < tas_priv->ndev; i++) {
+ tas_priv->tasdevice[i].cur_book = -1;
+ tas_priv->tasdevice[i].cur_prog = -1;
+ tas_priv->tasdevice[i].cur_conf = -1;
+ }
+ tas2781_reset(tas_priv);
+ tasdevice_prmg_load(tas_priv, 0);
+ tas_priv->cur_prog = 0;
+
+ /* If calibrated data occurs error, dsp will still works with default
+ * calibrated data inside algo.
+ */
+ if (tas_priv->cali_data.total_sz > calib_data_sz)
+ tas2781_apply_calib(tas_priv);
+ mutex_unlock(&tas_priv->codec_lock);
+
+ return 0;
+}
+
+static const struct dev_pm_ops tas2781_hda_pm_ops = {
+ RUNTIME_PM_OPS(tas2781_runtime_suspend, tas2781_runtime_resume,
+ NULL)
+ SYSTEM_SLEEP_PM_OPS(tas2781_system_suspend, tas2781_system_resume)
+};
+
+static const struct i2c_device_id tas2781_hda_i2c_id[] = {
+ { "tas2781-hda", 0 },
+ {}
+};
+
+static const struct acpi_device_id tas2781_acpi_hda_match[] = {
+ {"TIAS2781", 0 },
+ {}
+};
+MODULE_DEVICE_TABLE(acpi, tas2781_acpi_hda_match);
+
+static struct i2c_driver tas2781_hda_i2c_driver = {
+ .driver = {
+ .name = "tas2781-hda",
+ .acpi_match_table = tas2781_acpi_hda_match,
+ .pm = &tas2781_hda_pm_ops,
+ },
+ .id_table = tas2781_hda_i2c_id,
+ .probe_new = tas2781_hda_i2c_probe,
+ .remove = tas2781_hda_i2c_remove,
+};
+module_i2c_driver(tas2781_hda_i2c_driver);
+
+MODULE_DESCRIPTION("TAS2781 HDA Driver");
+MODULE_AUTHOR("Shenghao Ding, TI, <[email protected]>");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(SND_SOC_TAS2781_FMWLIB);
--
2.34.1




2023-05-28 08:38:49

by Christophe JAILLET

[permalink] [raw]
Subject: Re: [PATCH v4 5/6] ALSA: hda/tas2781: Add tas2781 HDA driver

Le 28/05/2023 à 00:36, Shenghao Ding a écrit :
> Create tas2781 HDA driver.
>
> Signed-off-by: Shenghao Ding <[email protected]>
>
> ---
> Changes in v4:
> - Add [email protected] into Cc list
> - remove unused ret in tas2781_hda_playback
> - in all *__put function, return 0, if the value is unchanged
> - remove superfluous
> - rewrite the subid judgement
> - dev_info to dev_dbg
> Changes to be committed:
> modified: sound/pci/hda/Kconfig
> modified: sound/pci/hda/Makefile
> new file: sound/pci/hda/tas2781_hda_i2c.c
> ---
> sound/pci/hda/Kconfig | 15 +
> sound/pci/hda/Makefile | 2 +
> sound/pci/hda/tas2781_hda_i2c.c | 834 ++++++++++++++++++++++++++++++++
> 3 files changed, 851 insertions(+)
> create mode 100644 sound/pci/hda/tas2781_hda_i2c.c

[...]

> +static int tas2781_acpi_get_i2c_resource(struct acpi_resource
> + *ares, void *data)
> +{
> + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)data;

Nit: Is the cast really needed?
(should you feel like removing it to ease reading, their are a few other
onces elsewhere)

> + struct acpi_resource_i2c_serialbus *sb;
> +
> + if (i2c_acpi_get_i2c_resource(ares, &sb)) {
> + if (sb->slave_address != TAS2781_GLOBAL_ADDR) {
> + tas_priv->tasdevice[tas_priv->ndev].dev_addr =
> + (unsigned int)sb->slave_address;
> + tas_priv->ndev++;
> + } else
> + tas_priv->glb_addr.dev_addr = TAS2781_GLOBAL_ADDR;
> +

Nit: Unneeded NL (or missing {} around the 'else' branch if it is the
style you prefer)

> + }
> +
> + return 1;
> +}

[...]

> +static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol,
> + struct snd_ctl_elem_value *ucontrol)
> +{
> + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
> + int ret = 0;
> +
> + if (tas_priv->rcabin.profile_cfg_id !=
> + ucontrol->value.integer.value[0]) {
> + tas_priv->rcabin.profile_cfg_id =
> + ucontrol->value.integer.value[0];
> + ret = 0;

So ret is always 0?

Either it is not needed and a "return 0;" below would be enough, either
the function should be void (if changinf the prototype is possible, not
sure), either there is a typo.

> + }
> +
> + return ret;
> +}
> +
> +static int tasdevice_create_control(struct tasdevice_priv *tas_priv)
> +{
> + char prof_ctrl_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN];
> + struct hda_codec *codec = tas_priv->codec;
> + struct snd_kcontrol_new prof_ctrl = {
> + .name = prof_ctrl_name,
> + .iface = SNDRV_CTL_ELEM_IFACE_CARD,
> + .info = tasdevice_info_profile,
> + .get = tasdevice_get_profile_id,
> + .put = tasdevice_set_profile_id,
> + };
> + int ret;
> +
> + /* Create a mixer item for selecting the active profile */
> + scnprintf(prof_ctrl_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN,
> + "spk-profile-id");
> + ret = snd_ctl_add(codec->card, snd_ctl_new1(&prof_ctrl, tas_priv));
> + if (ret) {
> + dev_err(tas_priv->dev, "Failed to add KControl %s = %d\n",

Nit: KControl here, Control a few lines below. I guess they should be
the same.

> + prof_ctrl.name, ret);
> + goto out;
> + }
> +
> + dev_dbg(tas_priv->dev, "Added Control %s\n", prof_ctrl.name);
> +
> +out:
> + return ret;
> +}

[...]

> +static int tasdevice_program_put(struct snd_kcontrol *kcontrol,
> + struct snd_ctl_elem_value *ucontrol)
> +{
> + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
> + unsigned int nr_program = ucontrol->value.integer.value[0];
> + int ret = 0;
> +
> + if (tas_priv->cur_prog != nr_program) {
> + tas_priv->cur_prog = nr_program;
> + ret = 1;

(Base on this, I guess, that the answer above for
tasdevice_set_profile_id() is : typo s/0/1/)

> + }
> +
> + return ret;
> +}
> +
> +static int tasdevice_config_get(struct snd_kcontrol *kcontrol,
> + struct snd_ctl_elem_value *ucontrol)
> +{
> +

Nit: Unneeded NL

> + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
> +
> + ucontrol->value.integer.value[0] = tas_priv->cur_conf;
> +
> + return 0;
> +}

[...]

> +static int tas2781_save_calibration(struct tasdevice_priv *tas_priv)
> +{
> + efi_guid_t efi_guid = EFI_GUID(0x02f9af02, 0x7734, 0x4233, 0xb4, 0x3d,
> + 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3);
> + static efi_char16_t efi_name[] = L"CALI_DATA";
> + struct tm *tm = &tas_priv->tm;
> + unsigned int attr, crc;
> + unsigned int *tmp_val;
> + efi_status_t status;
> + int ret = 0;
> +
> + //Lenovo devices

Nit: why a different style for comment?

> + if (tas_priv->catlog_id == LENOVO)
> + efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc, 0x09,
> + 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92);
> +
> + tas_priv->cali_data.total_sz = 0;
> + /* Get real size of UEFI variable */
> + status = efi.get_variable(efi_name, &efi_guid, &attr,
> + &tas_priv->cali_data.total_sz, tas_priv->cali_data.data);
> + if (status == EFI_BUFFER_TOO_SMALL) {
> + ret = -ENODEV;
> + /* Allocate data buffer of data_size bytes */
> + tas_priv->cali_data.data = devm_kzalloc(tas_priv->dev,
> + tas_priv->cali_data.total_sz, GFP_KERNEL);
> + if (!tas_priv->cali_data.data)
> + return -ENOMEM;
> + /* Get variable contents into buffer */
> + status = efi.get_variable(efi_name, &efi_guid, &attr,
> + &tas_priv->cali_data.total_sz,
> + tas_priv->cali_data.data);
> + if (status != EFI_SUCCESS) {
> + ret = -EINVAL;
> + goto out;

Nit: return -EINVAL; as just a few lines above?

> + }

If so, return -ENODEV; here would be more explicit.
So, 'ret' becomes useless and return 0; at the end of the function looks
enough.

> + }
> +
> + tmp_val = (unsigned int *)tas_priv->cali_data.data;
> +
> + crc = crc32(~0, tas_priv->cali_data.data, 84) ^ ~0;
> + dev_dbg(tas_priv->dev, "cali crc 0x%08x PK tmp_val 0x%08x\n",
> + crc, tmp_val[21]);
> +
> + if (crc == tmp_val[21]) {
> + time64_to_tm(tmp_val[20], 0, tm);
> + dev_dbg(tas_priv->dev, "%4ld-%2d-%2d, %2d:%2d:%2d\n",
> + tm->tm_year, tm->tm_mon, tm->tm_mday,
> + tm->tm_hour, tm->tm_min, tm->tm_sec);
> + tas2781_apply_calib(tas_priv);
> + }
> +out:
> + return ret;
> +}
> +
> +static void tasdevice_fw_ready(const struct firmware *fmw,
> + void *context)
> +{
> + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context;
> + struct hda_codec *codec = tas_priv->codec;
> + int i, ret = 0;

Nit: = 0 is not needed

> +
> + pm_runtime_get_sync(tas_priv->dev);
> + mutex_lock(&tas_priv->codec_lock);
> +
> + ret = tasdevice_rca_parser(tas_priv, fmw);
> + if (ret)
> + goto out;
> + tasdevice_create_control(tas_priv);

CJ


2023-06-06 16:25:52

by Takashi Iwai

[permalink] [raw]
Subject: Re: [PATCH v4 5/6] ALSA: hda/tas2781: Add tas2781 HDA driver

On Sun, 28 May 2023 00:36:13 +0200,
Shenghao Ding wrote:
>
> Create tas2781 HDA driver.
>
> Signed-off-by: Shenghao Ding <[email protected]>

You still give too short text for this kind of largish and intensive
changes. Please write more about what the patch does, caveats,
whatever worth to mention.

> --- /dev/null
> +++ b/sound/pci/hda/tas2781_hda_i2c.c
> +static int tas2781_acpi_get_i2c_resource(struct acpi_resource
> + *ares, void *data)

The line break there looks weird...

> +{
> + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)data;

Superfluous cast.

> +static int tas2781_hda_read_acpi(struct tasdevice_priv *tas_priv,
> + const char *hid)
> +{
> + struct acpi_device *adev;
> + struct device *physdev;
> + LIST_HEAD(resources);
> + const char *sub;
> + int ret;
> +
> + adev = acpi_dev_get_first_match_dev(hid, NULL, -1);
> + if (!adev) {
> + dev_err(tas_priv->dev,
> + "Failed to find an ACPI device for %s\n", hid);
> + return -ENODEV;
> + }
> + strcpy(tas_priv->dev_name, hid);

Safer to use strscpy().

> + physdev = get_device(acpi_get_first_physical_node(adev));
> + acpi_dev_put(adev);
> +
> + sub = acpi_get_subsystem_id(ACPI_HANDLE(physdev));
> + if (IS_ERR(sub))
> + sub = NULL;
> + dev_info(tas_priv->dev, "subid = %s\n", sub);
> +
> + tas_priv->acpi_subsystem_id = sub;
> +
> + ret = acpi_dev_get_resources(adev, &resources,
> + tas2781_acpi_get_i2c_resource, tas_priv);

Referencing adev after acpi_dev_put() doesn't sound good.
acpi_dev_put() should be done later instead.

> +static int tasdevice_set_profile_id(struct snd_kcontrol *kcontrol,
> + struct snd_ctl_elem_value *ucontrol)
> +{
> + struct tasdevice_priv *tas_priv = snd_kcontrol_chip(kcontrol);
> + int ret = 0;
> +
> + if (tas_priv->rcabin.profile_cfg_id !=
> + ucontrol->value.integer.value[0]) {
> + tas_priv->rcabin.profile_cfg_id =
> + ucontrol->value.integer.value[0];
> + ret = 0;

Should be ret=1 when the value changes.

Also, you should check the given value. It's not checked in the core
side, so any random value can be passed by user-space.
(Ditto for other *_put() functions.)

> +static int tasdevice_create_control(struct tasdevice_priv *tas_priv)
> +{
> + char prof_ctrl_name[SNDRV_CTL_ELEM_ID_NAME_MAXLEN];
> + struct hda_codec *codec = tas_priv->codec;
> + struct snd_kcontrol_new prof_ctrl = {
> + .name = prof_ctrl_name,
> + .iface = SNDRV_CTL_ELEM_IFACE_CARD,
> + .info = tasdevice_info_profile,
> + .get = tasdevice_get_profile_id,
> + .put = tasdevice_set_profile_id,
> + };
> + int ret;
> +
> + /* Create a mixer item for selecting the active profile */
> + scnprintf(prof_ctrl_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN,
> + "spk-profile-id");

The control name is way too ugly. It's not understandable for human.
Please use a more descriptive name.

Also, you need no temporary name buffer. Just pass the constant
string to the name field.

> +static int tasdevice_dsp_create_ctrls(struct tasdevice_priv
> + *tas_priv)
> +{
....
> + scnprintf(prog_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "spk-prog-id");
> + scnprintf(conf_name, SNDRV_CTL_ELEM_ID_NAME_MAXLEN, "spk-conf-id");

Again, too ugly names. Be more descriptive.

> +static int tas2781_save_calibration(struct tasdevice_priv *tas_priv)
> +{
> + efi_guid_t efi_guid = EFI_GUID(0x02f9af02, 0x7734, 0x4233, 0xb4, 0x3d,
> + 0x93, 0xfe, 0x5a, 0xa3, 0x5d, 0xb3);
> + static efi_char16_t efi_name[] = L"CALI_DATA";
> + struct tm *tm = &tas_priv->tm;
> + unsigned int attr, crc;
> + unsigned int *tmp_val;
> + efi_status_t status;
> + int ret = 0;
> +
> + //Lenovo devices
> + if (tas_priv->catlog_id == LENOVO)
> + efi_guid = EFI_GUID(0x1f52d2a1, 0xbb3a, 0x457d, 0xbc, 0x09,
> + 0x43, 0xa3, 0xf4, 0x31, 0x0a, 0x92);
> +
> + tas_priv->cali_data.total_sz = 0;
> + /* Get real size of UEFI variable */
> + status = efi.get_variable(efi_name, &efi_guid, &attr,
> + &tas_priv->cali_data.total_sz, tas_priv->cali_data.data);
> + if (status == EFI_BUFFER_TOO_SMALL) {
> + ret = -ENODEV;
> + /* Allocate data buffer of data_size bytes */
> + tas_priv->cali_data.data = devm_kzalloc(tas_priv->dev,
> + tas_priv->cali_data.total_sz, GFP_KERNEL);
> + if (!tas_priv->cali_data.data)
> + return -ENOMEM;
> + /* Get variable contents into buffer */
> + status = efi.get_variable(efi_name, &efi_guid, &attr,
> + &tas_priv->cali_data.total_sz,
> + tas_priv->cali_data.data);
> + if (status != EFI_SUCCESS) {
> + ret = -EINVAL;
> + goto out;
> + }

... so at this point, the function still keeps ret=-ENODEV, and it
ends up with the final error code to be returned? It's not clear from
the code whether it's the intended flow.

> +static void tasdevice_fw_ready(const struct firmware *fmw,
> + void *context)
> +{
> + struct tasdevice_priv *tas_priv = (struct tasdevice_priv *)context;

Superfluous cast.

> + struct hda_codec *codec = tas_priv->codec;
> + int i, ret = 0;

Superfluous initialization.

> +static int tas2781_hda_bind(struct device *dev, struct device *master,
> + void *master_data)
> +{
> + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
> + struct hda_component *comps = master_data;
> + struct hda_codec *codec;
> + unsigned int subid;
> + int ret;
> +
> + if (!comps || tas_priv->index < 0 ||
> + tas_priv->index >= HDA_MAX_COMPONENTS)
> + return -EINVAL;
> +
> + comps = &comps[tas_priv->index];
> + if (comps->dev)
> + return -EBUSY;
> +
> + codec = comps->codec;
> + subid = codec->core.subsystem_id & 0xFFFF;
> +
> + //Lenovo devices
> + if ((subid == 0x387d) || (subid == 0x387e) || (subid == 0x3881)
> + || (subid == 0x3884) || (subid == 0x3886) || (subid == 0x38a7)
> + || (subid == 0x38a8) || (subid == 0x38ba) || (subid == 0x38bb)
> + || (subid == 0x38be) || (subid == 0x38bf) || (subid == 0x38c3)
> + || (subid == 0x38cb) || (subid == 0x38cd))
> + tas_priv->catlog_id = LENOVO;
> + else
> + tas_priv->catlog_id = OTHERS;

Hmm, I don't like checking subid here, but we can live with it for
now...

> +static int tas2781_runtime_suspend(struct device *dev)
> +{
> + struct tasdevice_priv *tas_priv = dev_get_drvdata(dev);
> + int i;
> +
> + dev_info(tas_priv->dev, "Runtime Suspend\n");

Don't spew at each runtime suspend/resume. It'll be way too much.
It should be dev_dbg(), if any.


thanks,

Takashi

2023-06-06 16:26:22

by Mark Brown

[permalink] [raw]
Subject: Re: [PATCH v4 5/6] ALSA: hda/tas2781: Add tas2781 HDA driver

On Tue, Jun 06, 2023 at 06:08:51PM +0200, Takashi Iwai wrote:
> Shenghao Ding wrote:

> > + //Lenovo devices
> > + if ((subid == 0x387d) || (subid == 0x387e) || (subid == 0x3881)
> > + || (subid == 0x3884) || (subid == 0x3886) || (subid == 0x38a7)
> > + || (subid == 0x38a8) || (subid == 0x38ba) || (subid == 0x38bb)
> > + || (subid == 0x38be) || (subid == 0x38bf) || (subid == 0x38c3)
> > + || (subid == 0x38cb) || (subid == 0x38cd))
> > + tas_priv->catlog_id = LENOVO;
> > + else
> > + tas_priv->catlog_id = OTHERS;

> Hmm, I don't like checking subid here, but we can live with it for
> now...

Might be more idiomatically/neatly written as a switch statement though.


Attachments:
(No filename) (694.00 B)
signature.asc (499.00 B)
Download all attachments

2023-06-06 16:28:31

by Takashi Iwai

[permalink] [raw]
Subject: Re: [PATCH v4 5/6] ALSA: hda/tas2781: Add tas2781 HDA driver

On Tue, 06 Jun 2023 18:10:13 +0200,
Mark Brown wrote:
>
> On Tue, Jun 06, 2023 at 06:08:51PM +0200, Takashi Iwai wrote:
> > Shenghao Ding wrote:
>
> > > + //Lenovo devices
> > > + if ((subid == 0x387d) || (subid == 0x387e) || (subid == 0x3881)
> > > + || (subid == 0x3884) || (subid == 0x3886) || (subid == 0x38a7)
> > > + || (subid == 0x38a8) || (subid == 0x38ba) || (subid == 0x38bb)
> > > + || (subid == 0x38be) || (subid == 0x38bf) || (subid == 0x38c3)
> > > + || (subid == 0x38cb) || (subid == 0x38cd))
> > > + tas_priv->catlog_id = LENOVO;
> > > + else
> > > + tas_priv->catlog_id = OTHERS;
>
> > Hmm, I don't like checking subid here, but we can live with it for
> > now...
>
> Might be more idiomatically/neatly written as a switch statement though.

Yes, it'll make it easier to add a new entry, too.


thanks,

Takashi