A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
and Audio. The audio clock controller is different from others, but the
rest are very similar from a functional and regmap point of view.
This patch series add support for Amlogic A1 PLL and Peripherals clock
drivers.
It blocks all A1 peripherals mainline support and a couple of patch series,
which were already reviewed and acked, but weren't merged due to pending
clock controller drivers series, e.g.
https://lore.kernel.org/all/[email protected]/
TODO: CPU and Audio clock controllers are not included in this patch
series, it will be sent later. The following clks from these controllers
are not supported for now:
* Audio clks - vad, mclk_vad, mclk_d, resample_a, locker_in, mclk_b,
pdmdclk, pdmsysclk, eqdrc, spdifin, mclk_a, audio2_toaudiotop,
audio2_tovad, audio2_toddr_vad, audio2_tdmin_vad, audio2_pdm,
audio2_ddr_arb, audio_audiolocker, audio_eqdrc, audio_resamplea,
audio_spdifin, audio_toddrb, audio_toddra, audio_frddrb, audio_frddra,
audio_tdmoutb, audio_tdmouta, audio_loopbacka, audio_tdminlb,
audio_tdminb, audio_tdmina, audio_ddr_arb, mclk_c
* CPU clks: cpu_fixed_source_sel0, cpu_fixed_source_div0,
cpu_fixed_source_sel1, cpu_fixed_source_div1, cpu_clk
Validation:
* to double check all clk flags run below helper script:
pushd /sys/kernel/debug/clk
for f in *; do
if [[ -f "$f/clk_flags" ]]; then
flags="$(cat $f/clk_flags | awk '{$1=$1};1' | sed ':a;N;$!ba;s/\n/ | /g')"
echo -e "$f: $flags"
fi
done
popd
* to trace current clks state use '/sys/kernel/debug/clk/clk_dump' node
with jq post-processing:
$ cat /sys/kernel/debug/clk/clk_dump | jq '.' > clk_dump.json
* to debug clk rate propagation, compile kernel with the following
definition:
$ sed -i "s/undef CLOCK_ALLOW_WRITE_DEBUGFS/define CLOCK_ALLOW_WRITE_DEBUGFS/g" drivers/clk/clk.c
after that, clk_rate debug node for each clock will be available for
write operation
Changes v15 since v14 as [15]:
- rename all dt bindings related to A1 Peripherals Clock Controller
from "*a1-clkc*" to "*a1-peripherals-clkc*"
- change COMMON_CLK_A1 config to COMMON_CLK_A1_PERIPHERALS
- rename compatible string from "a1-clkc" to "a1-peripherals-clkc"
- open the SD_EMMC_SEL2 clock object to public dt bindings due to
several hardware issues during auto-reparenting with rate
propagation; currently, the Meson MMC driver initializes its
parent using an assigned-clocks mechanism and sets an appropriate
rate. A related patch for meson-a1.dtsi will be provided after the
clock patch series is merged
- remove 'driver' keyword from dt bindings commit msgs and patchsets
- make English grammar better!
Changes v14 since v13 at [14]:
- remove the term "Meson" from all patchsets or replace it with
"Amlogic"
- purge extra commas as per Martin's suggestion
- drop the unneeded use of of_match_ptr(), since all Meson clock
drivers depend on the ARM64 config which selects CONFIG_OF by default
Changes v13 since v12 at [13]:
- make the clock object registration order from the roots to the leaves
- rearrange the clkids following above rule
Changes v12 since v11 at [12]:
- split the DT bindings patchset into two patches: one for the PLL clock
controller driver, and one for the peripherals clock controller driver
- to satisfy the DT binding checker, use fake references to the
peripherals clock controller in the PLL DT bindings schema, and then
replace them with real references when the peripherals bindings
become available.
- remove the public/private clocks concept from both controllers,
and instead use a linear clkid list with both exposed and internal
objects, all of which are registered in the clock provider
- combine all comments about RTC children with the flag
'CLK_SET_RATE_NO_REPARENT' into a single item with multiple
references to it
Changes v11 since v10 at [11]:
- change include/dt-bindings license to proper value required for
bindings files: 'GPL-2.0-only OR BSD-2-Clause'
- pll and peripherals clocks are split into public and private parts;
public clocks are available for external consumers through the DT layer,
private clocks include internal muxes and dividers of composite clocks,
they are placed inside clock controller driver without external access
- make public clks CLKID bindings continuous
- mark the following clock muxes as NO_REPARENT and add them to
public clocks list: GEN_SEL, DSPA_A_SEL, DSPA_B_SEL, DSPB_A_SEL,
DSP_B_B_SEL, PWM_A_SEL, PWM_B_SEL, PWM_C_SEL, PWM_D_SEL,
PWM_E_SEL, PWM_F_SEL, CECA_32K_SEL, CECB_32K_SEL; each of them can
be inherited from more accurate RTC clock and sometimes it's
required to forbid reparenting in such situation; also GEN_SEL can
be connected to external PAD and should not change parent
automatically due to rate propagation. For such clocks user must
setup parents on the DT side
Changes v10 since v9 at [10]:
- split general clk-pll changes into two different patchsets:
optional rst usage and new power sequence
- squash dt bindings patchsets to avoid chicken-or-the-egg problem
during run dt binding check routines
- add vendor prefix to PLL and Peripherals clkcs bindings filenames
- clear managed hifi_pll fields from initial poke table
- move DSPA_SEL, DSPB_SEL and SARADC_SEL to private clkid table,
because it should not be opened for direct usage
- pwm_a clk used for voltage regulation is not critical anymore, it
must be included to the proper cpu voltage regulation setup (will
be available in the next patch series)
- as discussed with Jerome, dspX clks are simple clocks and it
should be enabled/disabled/ignored/anything else from appropriate
DSP driver, so remove CLK_IGNORE_UNUSED tags
- provide more understandable comments and remove irrelevant (I hope so)
- remove CONFIG_OF usage, because it's redundant
- fix license issue, it's GPL-2.0+ only in the current version
- some commit msgs rewording
Changes v9 since v8 at [9]:
- remove common a1-clkc driver for the first version of a1 clock
controllers as Jerome suggested (it will be discussed after s4 and
a1 clks landed, hope so)
- replace inherited a1-pll clk_pll_ops with common ops and
оло introduce custom A1 PLL logic under MESON_PARM_APPLICABLE()
conditions
- rename xtal depended clocks in PLL and Peripherals domains
- remove 'a1_' prefix for all clocks, because they are already
inside A1 driver, it's redundant
- change udelay() to usleep_range() as preferred for small msec
amount
- purge all double quotes from the yaml schemas
- use proper dt node names following kernel guidelines
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
- use devm_platform_ioremap_resource() instead of simple
devm_ioremap_resource()
- mark all dspX clocks as CLK_IGNORE_UNUSED, because we do not want
to touch these clocks during CCF initialization due to possible
workload execution on it started from bootloader; in this case
bootloader already made all initialization stuff for dspX
- also mark all dspX with NO_REPARENT tag, because from dspX clocks
we want to select proper clk source from device tree
Changes v8 since v7 at [8]:
- introduced a1-clkc common driver for all A1 clock controllers
- exported meson_clk_pll_wait_lock symbol
- supported meson-a1-clkc common driver in the a1-pll and a1 clkc
- inherited a1-pll from the base clk-pll driver, implemented own
version of init/enable/disable/enabled routines; rate calculating
logic is fully the same
- aligned CLKID-related definitions with CLKID list from order
perspective to remove holes and permutations
- corrected Kconfig dependencies and types
- provided correct MODULE_AUTHORs()
- optimized and fixed up some clock relationships
- removed unused register offset definitions
- fixed up A1 PLL and Peripherals clkc dtb_check errors
- fixed clk_summary kernel panic due to missing a1_pad_ctrl
clk_regmap definition
- included PLL and Peripherals clk controllers to the base a1 dts
- The previous v7 version [8] had several logic and style problems,
all of them are resolved in this version. Original Jian Hu v7 patches
are not touched, and all additional fixes are implemented in separate
patches. Patch "clk: meson: add support for A1 PLL clock ops" is
removed, because a1-pll clk driver inherits all stuff from clk-pll
base driver, just implements custom init/enable/disable/is_enabled
callbacks.
Changes v7 since v6 at [7]:
- fix 'dt_binding_check' compiling error
- add acked-by
Changes v6 since v5 at [6]:
- fix yaml file
- add rst/current_en/l_detect parm detection
- remove 'meson_eeclkc_data' in a1.c and a1-pll.c
Changes v5 since v4 at [5]:
- change yaml GPL
- drop meson-eeclk.c patch, add probe function in each driver
- add CLK_IS_CRITICAL for sys_clk clock, drop the flag for sys_a
and sys_b
- add new parm for pll, add protection for rst parm
- drop flag for a1_fixed_pll
- remove the same comment for fclk_div, add "refer to"
- add critical flag for a1_sys_clk
- remove rtc table
- rename a1_dspa_en_dspa and a1_dspb_en_dspb
- remove useless comment
Changes v4 since v3 at [3]:
- fix reparenting orphan failed, it depends on jerome's patch [4]
- fix changelist in v3 about reparenting orphan
- remove the dts patch
Changes v3 since v2 at [2]:
- add probe function for A1
- separate the clock driver into two patch
- change some clock flags and ops
- add support for a1 PLL ops
- add A1 clock node
- fix reparenting orphan clock failed, registering xtal_fixpll
and xtal_hifipll after the provider registration, it is not
a best way.
Changes v2 since v1 at [1]:
- place A1 config alphabetically
- add actual reason for RO ops, CLK_IS_CRITICAL, CLK_IGNORE_UNUSED
- separate the driver into two driver: peripheral and pll driver
- delete CLK_IGNORE_UNUSED flag for pwm b/c/d/e/f clock, dsp clock
- delete the change in Kconfig.platforms, address to Kevin alone
- remove the useless comments
- modify the meson pll driver to support A1 PLLs
Links:
[1] https://lkml.kernel.org/r/[email protected]
[2] https://lkml.kernel.org/r/[email protected]
[3] https://lkml.kernel.org/r/[email protected]
[4] https://lkml.kernel.org/r/[email protected]
[5] https://lkml.kernel.org/r/[email protected]
[6] https://lkml.kernel.org/r/[email protected]
[7] https://lkml.kernel.org/r/[email protected]
[8] https://lore.kernel.org/linux-amlogic/[email protected]/
[9] https://lore.kernel.org/linux-amlogic/[email protected]/
[10] https://lore.kernel.org/all/[email protected]/
[11] https://lore.kernel.org/all/[email protected]/
[12] https://lore.kernel.org/all/[email protected]/
[13] https://lore.kernel.org/all/[email protected]/
[14] https://lore.kernel.org/linux-amlogic/[email protected]/
[15] https://lore.kernel.org/all/[email protected]/
Dmitry Rokosov (6):
clk: meson: make pll rst bit as optional
clk: meson: introduce new pll power-on sequence for A1 SoC family
dt-bindings: clock: meson: add A1 PLL clock controller bindings
clk: meson: a1: add Amlogic A1 PLL clock controller driver
dt-bindings: clock: meson: add A1 Peripherals clock controller
bindings
clk: meson: a1: add Amlogic A1 Peripherals clock controller driver
.../clock/amlogic,a1-peripherals-clkc.yaml | 73 +
.../bindings/clock/amlogic,a1-pll-clkc.yaml | 59 +
MAINTAINERS | 1 +
drivers/clk/meson/Kconfig | 20 +
drivers/clk/meson/Makefile | 2 +
drivers/clk/meson/a1-peripherals.c | 2273 +++++++++++++++++
drivers/clk/meson/a1-peripherals.h | 113 +
drivers/clk/meson/a1-pll.c | 356 +++
drivers/clk/meson/a1-pll.h | 47 +
drivers/clk/meson/clk-pll.c | 47 +-
drivers/clk/meson/clk-pll.h | 2 +
.../clock/amlogic,a1-peripherals-clkc.h | 115 +
.../dt-bindings/clock/amlogic,a1-pll-clkc.h | 20 +
13 files changed, 3121 insertions(+), 7 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-peripherals-clkc.yaml
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml
create mode 100644 drivers/clk/meson/a1-peripherals.c
create mode 100644 drivers/clk/meson/a1-peripherals.h
create mode 100644 drivers/clk/meson/a1-pll.c
create mode 100644 drivers/clk/meson/a1-pll.h
create mode 100644 include/dt-bindings/clock/amlogic,a1-peripherals-clkc.h
create mode 100644 include/dt-bindings/clock/amlogic,a1-pll-clkc.h
--
2.36.0
Add the documentation and dt bindings for Amlogic A1 PLL clock
controller.
Also include new A1 clock controller dt bindings to MAINTAINERS.
Signed-off-by: Jian Hu <[email protected]>
Signed-off-by: Dmitry Rokosov <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Reviewed-by: Martin Blumenstingl <[email protected]>
---
.../bindings/clock/amlogic,a1-pll-clkc.yaml | 58 +++++++++++++++++++
MAINTAINERS | 1 +
.../dt-bindings/clock/amlogic,a1-pll-clkc.h | 20 +++++++
3 files changed, 79 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml
create mode 100644 include/dt-bindings/clock/amlogic,a1-pll-clkc.h
diff --git a/Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml b/Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml
new file mode 100644
index 000000000000..5c6fa620a63c
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/amlogic,a1-pll-clkc.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/amlogic,a1-pll-clkc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Amlogic A1 PLL Clock Control Unit
+
+maintainers:
+ - Neil Armstrong <[email protected]>
+ - Jerome Brunet <[email protected]>
+ - Jian Hu <[email protected]>
+ - Dmitry Rokosov <[email protected]>
+
+properties:
+ compatible:
+ const: amlogic,a1-pll-clkc
+
+ '#clock-cells':
+ const: 1
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: input fixpll_in
+ - description: input hifipll_in
+
+ clock-names:
+ items:
+ - const: fixpll_in
+ - const: hifipll_in
+
+required:
+ - compatible
+ - '#clock-cells'
+ - reg
+ - clocks
+ - clock-names
+
+additionalProperties: false
+
+examples:
+ - |
+ apb {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clock-controller@7c80 {
+ compatible = "amlogic,a1-pll-clkc";
+ reg = <0 0x7c80 0 0x18c>;
+ #clock-cells = <1>;
+ clocks = <&clkc_periphs_fixpll_in>,
+ <&clkc_periphs_hifipll_in>;
+ clock-names = "fixpll_in", "hifipll_in";
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 39ff1a717625..8438bc9bd636 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1895,6 +1895,7 @@ L: [email protected]
S: Maintained
F: Documentation/devicetree/bindings/clock/amlogic*
F: drivers/clk/meson/
+F: include/dt-bindings/clock/a1*
F: include/dt-bindings/clock/gxbb*
F: include/dt-bindings/clock/meson*
diff --git a/include/dt-bindings/clock/amlogic,a1-pll-clkc.h b/include/dt-bindings/clock/amlogic,a1-pll-clkc.h
new file mode 100644
index 000000000000..01fb8164ac29
--- /dev/null
+++ b/include/dt-bindings/clock/amlogic,a1-pll-clkc.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#ifndef __A1_PLL_CLKC_H
+#define __A1_PLL_CLKC_H
+
+#define CLKID_FIXED_PLL 1
+#define CLKID_FCLK_DIV2 6
+#define CLKID_FCLK_DIV3 7
+#define CLKID_FCLK_DIV5 8
+#define CLKID_FCLK_DIV7 9
+#define CLKID_HIFI_PLL 10
+
+#endif /* __A1_PLL_CLKC_H */
--
2.36.0
Modern meson PLL IPs are a little bit different from early known PLLs.
The main difference is located in the init/enable/disable sequences; the
rate logic is the same.
In A1 PLL, the PLL enable sequence is different, so add new optional pll
reg bits and use the new power-on sequence to enable the PLL:
1. enable the pll, delay for 10us
2. enable the pll self-adaption current module, delay for 40us
3. enable the lock detect module
Signed-off-by: Jian Hu <[email protected]>
Acked-by: Martin Blumenstingl <[email protected]>
Signed-off-by: Dmitry Rokosov <[email protected]>
---
drivers/clk/meson/clk-pll.c | 23 +++++++++++++++++++++++
drivers/clk/meson/clk-pll.h | 2 ++
2 files changed, 25 insertions(+)
diff --git a/drivers/clk/meson/clk-pll.c b/drivers/clk/meson/clk-pll.c
index 314ca945a4d0..56ec2210f1ad 100644
--- a/drivers/clk/meson/clk-pll.c
+++ b/drivers/clk/meson/clk-pll.c
@@ -358,6 +358,25 @@ static int meson_clk_pll_enable(struct clk_hw *hw)
if (MESON_PARM_APPLICABLE(&pll->rst))
meson_parm_write(clk->map, &pll->rst, 0);
+ /*
+ * Compared with the previous SoCs, self-adaption current module
+ * is newly added for A1, keep the new power-on sequence to enable the
+ * PLL. The sequence is:
+ * 1. enable the pll, delay for 10us
+ * 2. enable the pll self-adaption current module, delay for 40us
+ * 3. enable the lock detect module
+ */
+ if (MESON_PARM_APPLICABLE(&pll->current_en)) {
+ usleep_range(10, 20);
+ meson_parm_write(clk->map, &pll->current_en, 1);
+ usleep_range(40, 50);
+ };
+
+ if (MESON_PARM_APPLICABLE(&pll->l_detect)) {
+ meson_parm_write(clk->map, &pll->l_detect, 1);
+ meson_parm_write(clk->map, &pll->l_detect, 0);
+ }
+
if (meson_clk_pll_wait_lock(hw))
return -EIO;
@@ -375,6 +394,10 @@ static void meson_clk_pll_disable(struct clk_hw *hw)
/* Disable the pll */
meson_parm_write(clk->map, &pll->en, 0);
+
+ /* Disable PLL internal self-adaption current module */
+ if (MESON_PARM_APPLICABLE(&pll->current_en))
+ meson_parm_write(clk->map, &pll->current_en, 0);
}
static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
diff --git a/drivers/clk/meson/clk-pll.h b/drivers/clk/meson/clk-pll.h
index 367efd0f6410..a2228c0fdce5 100644
--- a/drivers/clk/meson/clk-pll.h
+++ b/drivers/clk/meson/clk-pll.h
@@ -36,6 +36,8 @@ struct meson_clk_pll_data {
struct parm frac;
struct parm l;
struct parm rst;
+ struct parm current_en;
+ struct parm l_detect;
const struct reg_sequence *init_regs;
unsigned int init_count;
const struct pll_params_table *table;
--
2.36.0
Introduce Peripherals clock controller for Amlogic A1 SoC family.
A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
and Audio.
This patchset adds support for Amlogic A1 Peripherals clock driver and
allows to generate clocks for all A1 SoC peripheral IPs.
Signed-off-by: Jian Hu <[email protected]>
Signed-off-by: Dmitry Rokosov <[email protected]>
---
drivers/clk/meson/Kconfig | 10 +
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/a1-peripherals.c | 2273 ++++++++++++++++++++++++++++
drivers/clk/meson/a1-peripherals.h | 113 ++
4 files changed, 2397 insertions(+)
create mode 100644 drivers/clk/meson/a1-peripherals.c
create mode 100644 drivers/clk/meson/a1-peripherals.h
diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index 693c4cf60f27..8ce846fdbe43 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -109,6 +109,16 @@ config COMMON_CLK_A1_PLL
device, A1 SoC Family. Say Y if you want A1 PLL clock controller
to work.
+config COMMON_CLK_A1_PERIPHERALS
+ tristate "Amlogic A1 SoC Peripherals clock controller support"
+ depends on ARM64
+ select COMMON_CLK_MESON_DUALDIV
+ select COMMON_CLK_MESON_REGMAP
+ help
+ Support for the Peripherals clock controller on Amlogic A113L based
+ device, A1 SoC Family. Say Y if you want A1 Peripherals clock
+ controller to work.
+
config COMMON_CLK_G12A
tristate "G12 and SM1 SoC clock controllers support"
depends on ARM64
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 2f17f475a48f..d5288662881d 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o
obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
+obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
diff --git a/drivers/clk/meson/a1-peripherals.c b/drivers/clk/meson/a1-peripherals.c
new file mode 100644
index 000000000000..5e7a37cbbb88
--- /dev/null
+++ b/drivers/clk/meson/a1-peripherals.c
@@ -0,0 +1,2273 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "a1-peripherals.h"
+#include "clk-dualdiv.h"
+#include "clk-regmap.h"
+
+static struct clk_regmap xtal_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "xtal_in",
+ .ops = &clk_regmap_gate_ro_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fixpll_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "fixpll_in",
+ .ops = &clk_regmap_gate_ro_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap usb_phy_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 2,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_phy_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap usb_ctrl_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 3,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_ctrl_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap hifipll_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 4,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "hifipll_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap syspll_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 5,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "syspll_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap dds_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_OSCIN_CTRL,
+ .bit_idx = 6,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dds_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap rtc_32k_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "rtc_32k_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static const struct meson_clk_dualdiv_param clk_32k_div_table[] = {
+ {
+ .dual = 1,
+ .n1 = 733,
+ .m1 = 8,
+ .n2 = 732,
+ .m2 = 11,
+ },
+ {}
+};
+
+static struct clk_regmap rtc_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = RTC_BY_OSCIN_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = RTC_BY_OSCIN_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = RTC_BY_OSCIN_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = clk_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap rtc_32k_xtal = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL1,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "rtc_32k_xtal",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap rtc_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = RTC_CTRL,
+ .mask = 0x3,
+ .shift = 0,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_xtal.hw,
+ &rtc_32k_div.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/*
+ * All clocks that can be inherited from a more accurate RTC clock are marked
+ * with the CLK_SET_RATE_NO_REPARENT flag. This is because in certain
+ * situations, we may need to freeze their parent. The parent setup of these
+ * clocks should be located on the device tree side.
+ */
+struct clk_regmap rtc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = RTC_BY_OSCIN_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "rtc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &rtc_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static u32 mux_table_sys[] = { 0, 1, 2, 3, 7 };
+static const struct clk_parent_data sys_parents[] = {
+ { .fw_name = "xtal" },
+ { .fw_name = "fclk_div2" },
+ { .fw_name = "fclk_div3" },
+ { .fw_name = "fclk_div5" },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap sys_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_sys,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_b_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_data = sys_parents,
+ .num_parents = ARRAY_SIZE(sys_parents),
+ },
+};
+
+static struct clk_regmap sys_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SYS_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sys_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_sys,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_a_sel",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_data = sys_parents,
+ .num_parents = ARRAY_SIZE(sys_parents),
+ },
+};
+
+static struct clk_regmap sys_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SYS_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SYS_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sys_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sys = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SYS_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 31,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sys",
+ .ops = &clk_regmap_mux_ro_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sys_a.hw,
+ &sys_b.hw,
+ },
+ .num_parents = 2,
+ /*
+ * This clock is used by APB bus which is set in boot ROM code
+ * and is required by the platform to operate correctly.
+ * Until the following condition are met, we need this clock to
+ * be marked as critical:
+ * a) Mark the clock used by a firmware resource, if possible
+ * b) CCF has a clock hand-off mechanism to make the sure the
+ * clock stays on until the proper driver comes along
+ */
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+ },
+};
+
+static u32 mux_table_dsp_ab[] = { 0, 1, 2, 3, 4, 7 };
+static const struct clk_parent_data dsp_ab_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .fw_name = "fclk_div2", },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+ { .fw_name = "hifi_pll", },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap dspa_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspa_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPA_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspa_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPA_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPA_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspa_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_a.hw,
+ &dspa_b.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_en = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_EN,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_en",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspa_en_nic = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPA_CLK_EN,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspa_en_nic",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspa_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 10,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspb_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPB_CLK_CTRL0,
+ .shift = 0,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_CTRL0,
+ .bit_idx = 13,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x7,
+ .shift = 26,
+ .table = mux_table_dsp_ab,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = dsp_ab_parent_data,
+ .num_parents = ARRAY_SIZE(dsp_ab_parent_data),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap dspb_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DSPB_CLK_CTRL0,
+ .shift = 16,
+ .width = 10,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_CTRL0,
+ .bit_idx = 29,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DSPB_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dspb_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_a.hw,
+ &dspb_b.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_en = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_EN,
+ .bit_idx = 1,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_en",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dspb_en_nic = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DSPB_CLK_EN,
+ .bit_idx = 0,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dspb_en_nic",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dspb_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap clk_24m = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "24m",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_fixed_factor clk_24m_div2 = {
+ .mult = 1,
+ .div = 2,
+ .hw.init = &(struct clk_init_data){
+ .name = "24m_div2",
+ .ops = &clk_fixed_factor_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &clk_24m.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap clk_12m = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 10,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "12m",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &clk_24m_div2.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div2_divn_pre = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = CLK12_24_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_divn_pre",
+ .ops = &clk_regmap_divider_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "fclk_div2",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap fclk_div2_divn = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CLK12_24_CTRL,
+ .bit_idx = 12,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "fclk_div2_divn",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &fclk_div2_divn_pre.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/*
+ * the index 2 is sys_pll_div16, it will be implemented in the CPU clock driver,
+ * the index 4 is the clock measurement source, it's not supported yet
+ */
+static u32 gen_table[] = { 0, 1, 3, 5, 6, 7, 8 };
+static const struct clk_parent_data gen_parent_data[] = {
+ { .fw_name = "xtal", },
+ { .hw = &rtc.hw },
+ { .fw_name = "hifi_pll", },
+ { .fw_name = "fclk_div2", },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+ { .fw_name = "fclk_div7", },
+};
+
+static struct clk_regmap gen_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = GEN_CLK_CTRL,
+ .mask = 0xf,
+ .shift = 12,
+ .table = gen_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "gen_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = gen_parent_data,
+ .num_parents = ARRAY_SIZE(gen_parent_data),
+ /*
+ * The GEN clock can be connected to an external pad, so it
+ * may be set up directly from the device tree. Additionally,
+ * the GEN clock can be inherited from a more accurate RTC
+ * clock, so in certain situations, it may be necessary
+ * to freeze its parent.
+ */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap gen_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = GEN_CLK_CTRL,
+ .shift = 0,
+ .width = 11,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "gen_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &gen_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap gen = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = GEN_CLK_CTRL,
+ .bit_idx = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "gen",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &gen_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap saradc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "saradc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw, },
+ },
+ .num_parents = 2,
+ },
+};
+
+static struct clk_regmap saradc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "saradc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &saradc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap saradc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SAR_ADC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "saradc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &saradc_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data pwm_abcd_parents[] = {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap pwm_a_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_a_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_a_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_a_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_a_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_a = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_a",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_a_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_b_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .mask = 0x1,
+ .shift = 25,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_b_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_b_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .shift = 16,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_b_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_b_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_b = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_AB_CTRL,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_b",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_b_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_c_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .mask = 0x1,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_c_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_c_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_c_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_c_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_c = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_c",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_c_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_d_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .mask = 0x1,
+ .shift = 25,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_d_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_abcd_parents,
+ .num_parents = ARRAY_SIZE(pwm_abcd_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_d_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .shift = 16,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_d_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_d_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_d = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_CD_CTRL,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_d",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_d_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data pwm_ef_parents[] = {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw },
+ { .fw_name = "fclk_div5", },
+ { .hw = &rtc.hw },
+};
+
+static struct clk_regmap pwm_e_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_e_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_ef_parents,
+ .num_parents = ARRAY_SIZE(pwm_ef_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_e_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_e_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_e_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_e = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_e",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_e_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_f_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .mask = 0x3,
+ .shift = 25,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_f_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = pwm_ef_parents,
+ .num_parents = ARRAY_SIZE(pwm_ef_parents),
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap pwm_f_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .shift = 16,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "pwm_f_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_f_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap pwm_f = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PWM_CLK_EF_CTRL,
+ .bit_idx = 24,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "pwm_f",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &pwm_f_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+/*
+ * spicc clk
+ * fdiv2 |\ |\ _____
+ * ---------| |---DIV--| | | | spicc out
+ * ---------| | | |-----|GATE |---------
+ * ..... |/ | / |_____|
+ * --------------------|/
+ * 24M
+ */
+static const struct clk_parent_data spicc_spifc_parents[] = {
+ { .fw_name = "fclk_div2"},
+ { .fw_name = "fclk_div3"},
+ { .fw_name = "fclk_div5"},
+ { .fw_name = "hifi_pll" },
+};
+
+static struct clk_regmap spicc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPICC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spicc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = spicc_spifc_parents,
+ .num_parents = ARRAY_SIZE(spicc_spifc_parents),
+ },
+};
+
+static struct clk_regmap spicc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SPICC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spicc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spicc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spicc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPICC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spicc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &spicc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spicc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SPICC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "spicc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spicc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap ts_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = TS_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ts_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap ts = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = TS_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "ts",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ts_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spifc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPIFC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spifc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = spicc_spifc_parents,
+ .num_parents = ARRAY_SIZE(spicc_spifc_parents),
+ },
+};
+
+static struct clk_regmap spifc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SPIFC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spifc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spifc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spifc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SPIFC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "spifc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &spifc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap spifc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SPIFC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "spifc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &spifc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data usb_bus_parents[] = {
+ { .fw_name = "xtal", },
+ { .hw = &sys.hw },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+};
+
+static struct clk_regmap usb_bus_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = USB_BUSCLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "usb_bus_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = usb_bus_parents,
+ .num_parents = ARRAY_SIZE(usb_bus_parents),
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap usb_bus_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = USB_BUSCLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "usb_bus_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &usb_bus_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap usb_bus = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = USB_BUSCLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "usb_bus",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &usb_bus_div.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct clk_parent_data sd_emmc_psram_dmc_parents[] = {
+ { .fw_name = "fclk_div2", },
+ { .fw_name = "fclk_div3", },
+ { .fw_name = "fclk_div5", },
+ { .fw_name = "hifi_pll", },
+};
+
+static struct clk_regmap sd_emmc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sd_emmc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = sd_emmc_psram_dmc_parents,
+ .num_parents = ARRAY_SIZE(sd_emmc_psram_dmc_parents),
+ },
+};
+
+static struct clk_regmap sd_emmc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sd_emmc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sd_emmc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sd_emmc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "sd_emmc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &sd_emmc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap sd_emmc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = SD_EMMC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "sd_emmc",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &sd_emmc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap psram_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PSRAM_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "psram_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = sd_emmc_psram_dmc_parents,
+ .num_parents = ARRAY_SIZE(sd_emmc_psram_dmc_parents),
+ },
+};
+
+static struct clk_regmap psram_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = PSRAM_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "psram_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &psram_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap psram_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = PSRAM_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "psram_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &psram_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap psram = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = PSRAM_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "psram",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &psram_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dmc_sel = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DMC_CLK_CTRL,
+ .mask = 0x3,
+ .shift = 9,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = sd_emmc_psram_dmc_parents,
+ .num_parents = ARRAY_SIZE(sd_emmc_psram_dmc_parents),
+ },
+};
+
+static struct clk_regmap dmc_div = {
+ .data = &(struct clk_regmap_div_data){
+ .offset = DMC_CLK_CTRL,
+ .shift = 0,
+ .width = 8,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_div",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dmc_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dmc_sel2 = {
+ .data = &(struct clk_regmap_mux_data){
+ .offset = DMC_CLK_CTRL,
+ .mask = 0x1,
+ .shift = 15,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "dmc_sel2",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &dmc_div.hw },
+ { .fw_name = "xtal", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap dmc = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = DMC_CLK_CTRL,
+ .bit_idx = 8,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "dmc",
+ .ops = &clk_regmap_gate_ro_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &dmc_sel2.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap ceca_32k_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECA_CLK_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "ceca_32k_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap ceca_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = CECA_CLK_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = CECA_CLK_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = CECA_CLK_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = CECA_CLK_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = CECA_CLK_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = clk_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap ceca_32k_sel_pre = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECA_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 24,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_sel_pre",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_div.hw,
+ &ceca_32k_in.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap ceca_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECA_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 31,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_sel_pre.hw,
+ &rtc.hw,
+ },
+ .num_parents = 2,
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap ceca_32k_out = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECA_CLK_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "ceca_32k_out",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &ceca_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cecb_32k_in = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECB_CLK_CTRL0,
+ .bit_idx = 31,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cecb_32k_in",
+ .ops = &clk_regmap_gate_ops,
+ .parent_data = &(const struct clk_parent_data) {
+ .fw_name = "xtal",
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap cecb_32k_div = {
+ .data = &(struct meson_clk_dualdiv_data){
+ .n1 = {
+ .reg_off = CECB_CLK_CTRL0,
+ .shift = 0,
+ .width = 12,
+ },
+ .n2 = {
+ .reg_off = CECB_CLK_CTRL0,
+ .shift = 12,
+ .width = 12,
+ },
+ .m1 = {
+ .reg_off = CECB_CLK_CTRL1,
+ .shift = 0,
+ .width = 12,
+ },
+ .m2 = {
+ .reg_off = CECB_CLK_CTRL1,
+ .shift = 12,
+ .width = 12,
+ },
+ .dual = {
+ .reg_off = CECB_CLK_CTRL0,
+ .shift = 28,
+ .width = 1,
+ },
+ .table = clk_32k_div_table,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_div",
+ .ops = &meson_clk_dualdiv_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_in.hw
+ },
+ .num_parents = 1,
+ },
+};
+
+static struct clk_regmap cecb_32k_sel_pre = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECB_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 24,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_sel_pre",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_div.hw,
+ &cecb_32k_in.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cecb_32k_sel = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CECB_CLK_CTRL1,
+ .mask = 0x1,
+ .shift = 31,
+ .flags = CLK_MUX_ROUND_CLOSEST,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_sel",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_sel_pre.hw,
+ &rtc.hw,
+ },
+ .num_parents = 2,
+ /* For more information, please refer to rtc clock */
+ .flags = CLK_SET_RATE_NO_REPARENT,
+ },
+};
+
+static struct clk_regmap cecb_32k_out = {
+ .data = &(struct clk_regmap_gate_data){
+ .offset = CECB_CLK_CTRL0,
+ .bit_idx = 30,
+ },
+ .hw.init = &(struct clk_init_data){
+ .name = "cecb_32k_out",
+ .ops = &clk_regmap_gate_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cecb_32k_sel.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+#define MESON_GATE(_name, _reg, _bit) \
+ MESON_PCLK(_name, _reg, _bit, &sys.hw)
+
+static MESON_GATE(clktree, SYS_CLK_EN0, 0);
+static MESON_GATE(reset_ctrl, SYS_CLK_EN0, 1);
+static MESON_GATE(analog_ctrl, SYS_CLK_EN0, 2);
+static MESON_GATE(pwr_ctrl, SYS_CLK_EN0, 3);
+static MESON_GATE(pad_ctrl, SYS_CLK_EN0, 4);
+static MESON_GATE(sys_ctrl, SYS_CLK_EN0, 5);
+static MESON_GATE(temp_sensor, SYS_CLK_EN0, 6);
+static MESON_GATE(am2axi_dev, SYS_CLK_EN0, 7);
+static MESON_GATE(spicc_b, SYS_CLK_EN0, 8);
+static MESON_GATE(spicc_a, SYS_CLK_EN0, 9);
+static MESON_GATE(msr, SYS_CLK_EN0, 10);
+static MESON_GATE(audio, SYS_CLK_EN0, 11);
+static MESON_GATE(jtag_ctrl, SYS_CLK_EN0, 12);
+static MESON_GATE(saradc_en, SYS_CLK_EN0, 13);
+static MESON_GATE(pwm_ef, SYS_CLK_EN0, 14);
+static MESON_GATE(pwm_cd, SYS_CLK_EN0, 15);
+static MESON_GATE(pwm_ab, SYS_CLK_EN0, 16);
+static MESON_GATE(cec, SYS_CLK_EN0, 17);
+static MESON_GATE(i2c_s, SYS_CLK_EN0, 18);
+static MESON_GATE(ir_ctrl, SYS_CLK_EN0, 19);
+static MESON_GATE(i2c_m_d, SYS_CLK_EN0, 20);
+static MESON_GATE(i2c_m_c, SYS_CLK_EN0, 21);
+static MESON_GATE(i2c_m_b, SYS_CLK_EN0, 22);
+static MESON_GATE(i2c_m_a, SYS_CLK_EN0, 23);
+static MESON_GATE(acodec, SYS_CLK_EN0, 24);
+static MESON_GATE(otp, SYS_CLK_EN0, 25);
+static MESON_GATE(sd_emmc_a, SYS_CLK_EN0, 26);
+static MESON_GATE(usb_phy, SYS_CLK_EN0, 27);
+static MESON_GATE(usb_ctrl, SYS_CLK_EN0, 28);
+static MESON_GATE(sys_dspb, SYS_CLK_EN0, 29);
+static MESON_GATE(sys_dspa, SYS_CLK_EN0, 30);
+static MESON_GATE(dma, SYS_CLK_EN0, 31);
+static MESON_GATE(irq_ctrl, SYS_CLK_EN1, 0);
+static MESON_GATE(nic, SYS_CLK_EN1, 1);
+static MESON_GATE(gic, SYS_CLK_EN1, 2);
+static MESON_GATE(uart_c, SYS_CLK_EN1, 3);
+static MESON_GATE(uart_b, SYS_CLK_EN1, 4);
+static MESON_GATE(uart_a, SYS_CLK_EN1, 5);
+static MESON_GATE(sys_psram, SYS_CLK_EN1, 6);
+static MESON_GATE(rsa, SYS_CLK_EN1, 8);
+static MESON_GATE(coresight, SYS_CLK_EN1, 9);
+static MESON_GATE(am2axi_vad, AXI_CLK_EN, 0);
+static MESON_GATE(audio_vad, AXI_CLK_EN, 1);
+static MESON_GATE(axi_dmc, AXI_CLK_EN, 3);
+static MESON_GATE(axi_psram, AXI_CLK_EN, 4);
+static MESON_GATE(ramb, AXI_CLK_EN, 5);
+static MESON_GATE(rama, AXI_CLK_EN, 6);
+static MESON_GATE(axi_spifc, AXI_CLK_EN, 7);
+static MESON_GATE(axi_nic, AXI_CLK_EN, 8);
+static MESON_GATE(axi_dma, AXI_CLK_EN, 9);
+static MESON_GATE(cpu_ctrl, AXI_CLK_EN, 10);
+static MESON_GATE(rom, AXI_CLK_EN, 11);
+static MESON_GATE(prod_i2c, AXI_CLK_EN, 12);
+
+/* Array of all clocks registered by this provider */
+static struct clk_hw_onecell_data a1_periphs_clks = {
+ .hws = {
+ [CLKID_XTAL_IN] = &xtal_in.hw,
+ [CLKID_FIXPLL_IN] = &fixpll_in.hw,
+ [CLKID_USB_PHY_IN] = &usb_phy_in.hw,
+ [CLKID_USB_CTRL_IN] = &usb_ctrl_in.hw,
+ [CLKID_HIFIPLL_IN] = &hifipll_in.hw,
+ [CLKID_SYSPLL_IN] = &syspll_in.hw,
+ [CLKID_DDS_IN] = &dds_in.hw,
+ [CLKID_SYS] = &sys.hw,
+ [CLKID_CLKTREE] = &clktree.hw,
+ [CLKID_RESET_CTRL] = &reset_ctrl.hw,
+ [CLKID_ANALOG_CTRL] = &analog_ctrl.hw,
+ [CLKID_PWR_CTRL] = &pwr_ctrl.hw,
+ [CLKID_PAD_CTRL] = &pad_ctrl.hw,
+ [CLKID_SYS_CTRL] = &sys_ctrl.hw,
+ [CLKID_TEMP_SENSOR] = &temp_sensor.hw,
+ [CLKID_AM2AXI_DIV] = &am2axi_dev.hw,
+ [CLKID_SPICC_B] = &spicc_b.hw,
+ [CLKID_SPICC_A] = &spicc_a.hw,
+ [CLKID_MSR] = &msr.hw,
+ [CLKID_AUDIO] = &audio.hw,
+ [CLKID_JTAG_CTRL] = &jtag_ctrl.hw,
+ [CLKID_SARADC_EN] = &saradc_en.hw,
+ [CLKID_PWM_EF] = &pwm_ef.hw,
+ [CLKID_PWM_CD] = &pwm_cd.hw,
+ [CLKID_PWM_AB] = &pwm_ab.hw,
+ [CLKID_CEC] = &cec.hw,
+ [CLKID_I2C_S] = &i2c_s.hw,
+ [CLKID_IR_CTRL] = &ir_ctrl.hw,
+ [CLKID_I2C_M_D] = &i2c_m_d.hw,
+ [CLKID_I2C_M_C] = &i2c_m_c.hw,
+ [CLKID_I2C_M_B] = &i2c_m_b.hw,
+ [CLKID_I2C_M_A] = &i2c_m_a.hw,
+ [CLKID_ACODEC] = &acodec.hw,
+ [CLKID_OTP] = &otp.hw,
+ [CLKID_SD_EMMC_A] = &sd_emmc_a.hw,
+ [CLKID_USB_PHY] = &usb_phy.hw,
+ [CLKID_USB_CTRL] = &usb_ctrl.hw,
+ [CLKID_SYS_DSPB] = &sys_dspb.hw,
+ [CLKID_SYS_DSPA] = &sys_dspa.hw,
+ [CLKID_DMA] = &dma.hw,
+ [CLKID_IRQ_CTRL] = &irq_ctrl.hw,
+ [CLKID_NIC] = &nic.hw,
+ [CLKID_GIC] = &gic.hw,
+ [CLKID_UART_C] = &uart_c.hw,
+ [CLKID_UART_B] = &uart_b.hw,
+ [CLKID_UART_A] = &uart_a.hw,
+ [CLKID_SYS_PSRAM] = &sys_psram.hw,
+ [CLKID_RSA] = &rsa.hw,
+ [CLKID_CORESIGHT] = &coresight.hw,
+ [CLKID_AM2AXI_VAD] = &am2axi_vad.hw,
+ [CLKID_AUDIO_VAD] = &audio_vad.hw,
+ [CLKID_AXI_DMC] = &axi_dmc.hw,
+ [CLKID_AXI_PSRAM] = &axi_psram.hw,
+ [CLKID_RAMB] = &ramb.hw,
+ [CLKID_RAMA] = &rama.hw,
+ [CLKID_AXI_SPIFC] = &axi_spifc.hw,
+ [CLKID_AXI_NIC] = &axi_nic.hw,
+ [CLKID_AXI_DMA] = &axi_dma.hw,
+ [CLKID_CPU_CTRL] = &cpu_ctrl.hw,
+ [CLKID_ROM] = &rom.hw,
+ [CLKID_PROC_I2C] = &prod_i2c.hw,
+ [CLKID_DSPA_SEL] = &dspa_sel.hw,
+ [CLKID_DSPB_SEL] = &dspb_sel.hw,
+ [CLKID_DSPA_EN] = &dspa_en.hw,
+ [CLKID_DSPA_EN_NIC] = &dspa_en_nic.hw,
+ [CLKID_DSPB_EN] = &dspb_en.hw,
+ [CLKID_DSPB_EN_NIC] = &dspb_en_nic.hw,
+ [CLKID_RTC] = &rtc.hw,
+ [CLKID_CECA_32K] = &ceca_32k_out.hw,
+ [CLKID_CECB_32K] = &cecb_32k_out.hw,
+ [CLKID_24M] = &clk_24m.hw,
+ [CLKID_12M] = &clk_12m.hw,
+ [CLKID_FCLK_DIV2_DIVN] = &fclk_div2_divn.hw,
+ [CLKID_GEN] = &gen.hw,
+ [CLKID_SARADC_SEL] = &saradc_sel.hw,
+ [CLKID_SARADC] = &saradc.hw,
+ [CLKID_PWM_A] = &pwm_a.hw,
+ [CLKID_PWM_B] = &pwm_b.hw,
+ [CLKID_PWM_C] = &pwm_c.hw,
+ [CLKID_PWM_D] = &pwm_d.hw,
+ [CLKID_PWM_E] = &pwm_e.hw,
+ [CLKID_PWM_F] = &pwm_f.hw,
+ [CLKID_SPICC] = &spicc.hw,
+ [CLKID_TS] = &ts.hw,
+ [CLKID_SPIFC] = &spifc.hw,
+ [CLKID_USB_BUS] = &usb_bus.hw,
+ [CLKID_SD_EMMC] = &sd_emmc.hw,
+ [CLKID_PSRAM] = &psram.hw,
+ [CLKID_DMC] = &dmc.hw,
+ [CLKID_SYS_A_SEL] = &sys_a_sel.hw,
+ [CLKID_SYS_A_DIV] = &sys_a_div.hw,
+ [CLKID_SYS_A] = &sys_a.hw,
+ [CLKID_SYS_B_SEL] = &sys_b_sel.hw,
+ [CLKID_SYS_B_DIV] = &sys_b_div.hw,
+ [CLKID_SYS_B] = &sys_b.hw,
+ [CLKID_DSPA_A_SEL] = &dspa_a_sel.hw,
+ [CLKID_DSPA_A_DIV] = &dspa_a_div.hw,
+ [CLKID_DSPA_A] = &dspa_a.hw,
+ [CLKID_DSPA_B_SEL] = &dspa_b_sel.hw,
+ [CLKID_DSPA_B_DIV] = &dspa_b_div.hw,
+ [CLKID_DSPA_B] = &dspa_b.hw,
+ [CLKID_DSPB_A_SEL] = &dspb_a_sel.hw,
+ [CLKID_DSPB_A_DIV] = &dspb_a_div.hw,
+ [CLKID_DSPB_A] = &dspb_a.hw,
+ [CLKID_DSPB_B_SEL] = &dspb_b_sel.hw,
+ [CLKID_DSPB_B_DIV] = &dspb_b_div.hw,
+ [CLKID_DSPB_B] = &dspb_b.hw,
+ [CLKID_RTC_32K_IN] = &rtc_32k_in.hw,
+ [CLKID_RTC_32K_DIV] = &rtc_32k_div.hw,
+ [CLKID_RTC_32K_XTAL] = &rtc_32k_xtal.hw,
+ [CLKID_RTC_32K_SEL] = &rtc_32k_sel.hw,
+ [CLKID_CECB_32K_IN] = &cecb_32k_in.hw,
+ [CLKID_CECB_32K_DIV] = &cecb_32k_div.hw,
+ [CLKID_CECB_32K_SEL_PRE] = &cecb_32k_sel_pre.hw,
+ [CLKID_CECB_32K_SEL] = &cecb_32k_sel.hw,
+ [CLKID_CECA_32K_IN] = &ceca_32k_in.hw,
+ [CLKID_CECA_32K_DIV] = &ceca_32k_div.hw,
+ [CLKID_CECA_32K_SEL_PRE] = &ceca_32k_sel_pre.hw,
+ [CLKID_CECA_32K_SEL] = &ceca_32k_sel.hw,
+ [CLKID_DIV2_PRE] = &fclk_div2_divn_pre.hw,
+ [CLKID_24M_DIV2] = &clk_24m_div2.hw,
+ [CLKID_GEN_SEL] = &gen_sel.hw,
+ [CLKID_GEN_DIV] = &gen_div.hw,
+ [CLKID_SARADC_DIV] = &saradc_div.hw,
+ [CLKID_PWM_A_SEL] = &pwm_a_sel.hw,
+ [CLKID_PWM_A_DIV] = &pwm_a_div.hw,
+ [CLKID_PWM_B_SEL] = &pwm_b_sel.hw,
+ [CLKID_PWM_B_DIV] = &pwm_b_div.hw,
+ [CLKID_PWM_C_SEL] = &pwm_c_sel.hw,
+ [CLKID_PWM_C_DIV] = &pwm_c_div.hw,
+ [CLKID_PWM_D_SEL] = &pwm_d_sel.hw,
+ [CLKID_PWM_D_DIV] = &pwm_d_div.hw,
+ [CLKID_PWM_E_SEL] = &pwm_e_sel.hw,
+ [CLKID_PWM_E_DIV] = &pwm_e_div.hw,
+ [CLKID_PWM_F_SEL] = &pwm_f_sel.hw,
+ [CLKID_PWM_F_DIV] = &pwm_f_div.hw,
+ [CLKID_SPICC_SEL] = &spicc_sel.hw,
+ [CLKID_SPICC_DIV] = &spicc_div.hw,
+ [CLKID_SPICC_SEL2] = &spicc_sel2.hw,
+ [CLKID_TS_DIV] = &ts_div.hw,
+ [CLKID_SPIFC_SEL] = &spifc_sel.hw,
+ [CLKID_SPIFC_DIV] = &spifc_div.hw,
+ [CLKID_SPIFC_SEL2] = &spifc_sel2.hw,
+ [CLKID_USB_BUS_SEL] = &usb_bus_sel.hw,
+ [CLKID_USB_BUS_DIV] = &usb_bus_div.hw,
+ [CLKID_SD_EMMC_SEL] = &sd_emmc_sel.hw,
+ [CLKID_SD_EMMC_DIV] = &sd_emmc_div.hw,
+ [CLKID_SD_EMMC_SEL2] = &sd_emmc_sel2.hw,
+ [CLKID_PSRAM_SEL] = &psram_sel.hw,
+ [CLKID_PSRAM_DIV] = &psram_div.hw,
+ [CLKID_PSRAM_SEL2] = &psram_sel2.hw,
+ [CLKID_DMC_SEL] = &dmc_sel.hw,
+ [CLKID_DMC_DIV] = &dmc_div.hw,
+ [CLKID_DMC_SEL2] = &dmc_sel2.hw,
+ [NR_CLKS] = NULL,
+ },
+ .num = NR_CLKS,
+};
+
+/* Convenience table to populate regmap in .probe */
+static struct clk_regmap *const a1_periphs_regmaps[] = {
+ &xtal_in,
+ &fixpll_in,
+ &usb_phy_in,
+ &usb_ctrl_in,
+ &hifipll_in,
+ &syspll_in,
+ &dds_in,
+ &sys,
+ &clktree,
+ &reset_ctrl,
+ &analog_ctrl,
+ &pwr_ctrl,
+ &pad_ctrl,
+ &sys_ctrl,
+ &temp_sensor,
+ &am2axi_dev,
+ &spicc_b,
+ &spicc_a,
+ &msr,
+ &audio,
+ &jtag_ctrl,
+ &saradc_en,
+ &pwm_ef,
+ &pwm_cd,
+ &pwm_ab,
+ &cec,
+ &i2c_s,
+ &ir_ctrl,
+ &i2c_m_d,
+ &i2c_m_c,
+ &i2c_m_b,
+ &i2c_m_a,
+ &acodec,
+ &otp,
+ &sd_emmc_a,
+ &usb_phy,
+ &usb_ctrl,
+ &sys_dspb,
+ &sys_dspa,
+ &dma,
+ &irq_ctrl,
+ &nic,
+ &gic,
+ &uart_c,
+ &uart_b,
+ &uart_a,
+ &sys_psram,
+ &rsa,
+ &coresight,
+ &am2axi_vad,
+ &audio_vad,
+ &axi_dmc,
+ &axi_psram,
+ &ramb,
+ &rama,
+ &axi_spifc,
+ &axi_nic,
+ &axi_dma,
+ &cpu_ctrl,
+ &rom,
+ &prod_i2c,
+ &dspa_sel,
+ &dspb_sel,
+ &dspa_en,
+ &dspa_en_nic,
+ &dspb_en,
+ &dspb_en_nic,
+ &rtc,
+ &ceca_32k_out,
+ &cecb_32k_out,
+ &clk_24m,
+ &clk_12m,
+ &fclk_div2_divn,
+ &gen,
+ &saradc_sel,
+ &saradc,
+ &pwm_a,
+ &pwm_b,
+ &pwm_c,
+ &pwm_d,
+ &pwm_e,
+ &pwm_f,
+ &spicc,
+ &ts,
+ &spifc,
+ &usb_bus,
+ &sd_emmc,
+ &psram,
+ &dmc,
+ &sys_a_sel,
+ &sys_a_div,
+ &sys_a,
+ &sys_b_sel,
+ &sys_b_div,
+ &sys_b,
+ &dspa_a_sel,
+ &dspa_a_div,
+ &dspa_a,
+ &dspa_b_sel,
+ &dspa_b_div,
+ &dspa_b,
+ &dspb_a_sel,
+ &dspb_a_div,
+ &dspb_a,
+ &dspb_b_sel,
+ &dspb_b_div,
+ &dspb_b,
+ &rtc_32k_in,
+ &rtc_32k_div,
+ &rtc_32k_xtal,
+ &rtc_32k_sel,
+ &cecb_32k_in,
+ &cecb_32k_div,
+ &cecb_32k_sel_pre,
+ &cecb_32k_sel,
+ &ceca_32k_in,
+ &ceca_32k_div,
+ &ceca_32k_sel_pre,
+ &ceca_32k_sel,
+ &fclk_div2_divn_pre,
+ &gen_sel,
+ &gen_div,
+ &saradc_div,
+ &pwm_a_sel,
+ &pwm_a_div,
+ &pwm_b_sel,
+ &pwm_b_div,
+ &pwm_c_sel,
+ &pwm_c_div,
+ &pwm_d_sel,
+ &pwm_d_div,
+ &pwm_e_sel,
+ &pwm_e_div,
+ &pwm_f_sel,
+ &pwm_f_div,
+ &spicc_sel,
+ &spicc_div,
+ &spicc_sel2,
+ &ts_div,
+ &spifc_sel,
+ &spifc_div,
+ &spifc_sel2,
+ &usb_bus_sel,
+ &usb_bus_div,
+ &sd_emmc_sel,
+ &sd_emmc_div,
+ &sd_emmc_sel2,
+ &psram_sel,
+ &psram_div,
+ &psram_sel2,
+ &dmc_sel,
+ &dmc_div,
+ &dmc_sel2,
+};
+
+static struct regmap_config a1_periphs_regmap_cfg = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static int meson_a1_periphs_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ void __iomem *base;
+ struct regmap *map;
+ int clkid, i, err;
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return dev_err_probe(dev, PTR_ERR(base),
+ "can't ioremap resource\n");
+
+ map = devm_regmap_init_mmio(dev, base, &a1_periphs_regmap_cfg);
+ if (IS_ERR(map))
+ return dev_err_probe(dev, PTR_ERR(map),
+ "can't init regmap mmio region\n");
+
+ /* Populate regmap for the regmap backed clocks */
+ for (i = 0; i < ARRAY_SIZE(a1_periphs_regmaps); i++)
+ a1_periphs_regmaps[i]->map = map;
+
+ for (clkid = 0; clkid < a1_periphs_clks.num; clkid++) {
+ err = devm_clk_hw_register(dev, a1_periphs_clks.hws[clkid]);
+ if (err)
+ return dev_err_probe(dev, err,
+ "clock[%d] registration failed\n",
+ clkid);
+ }
+
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get,
+ &a1_periphs_clks);
+}
+
+static const struct of_device_id a1_periphs_clkc_match_table[] = {
+ { .compatible = "amlogic,a1-peripherals-clkc", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a1_periphs_clkc_match_table);
+
+static struct platform_driver a1_periphs_clkc_driver = {
+ .probe = meson_a1_periphs_probe,
+ .driver = {
+ .name = "a1-peripherals-clkc",
+ .of_match_table = a1_periphs_clkc_match_table,
+ },
+};
+
+module_platform_driver(a1_periphs_clkc_driver);
+MODULE_AUTHOR("Jian Hu <[email protected]>");
+MODULE_AUTHOR("Dmitry Rokosov <[email protected]>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/meson/a1-peripherals.h b/drivers/clk/meson/a1-peripherals.h
new file mode 100644
index 000000000000..526fc9ba5c9f
--- /dev/null
+++ b/drivers/clk/meson/a1-peripherals.h
@@ -0,0 +1,113 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Amlogic A1 Peripherals Clock Controller internals
+ *
+ * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
+ * Author: Jian Hu <[email protected]>
+ *
+ * Copyright (c) 2023, SberDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <[email protected]>
+ */
+
+#ifndef __A1_PERIPHERALS_H
+#define __A1_PERIPHERALS_H
+
+/* peripherals clock controller register offset */
+#define SYS_OSCIN_CTRL 0x0
+#define RTC_BY_OSCIN_CTRL0 0x4
+#define RTC_BY_OSCIN_CTRL1 0x8
+#define RTC_CTRL 0xc
+#define SYS_CLK_CTRL0 0x10
+#define SYS_CLK_EN0 0x1c
+#define SYS_CLK_EN1 0x20
+#define AXI_CLK_EN 0x24
+#define DSPA_CLK_EN 0x28
+#define DSPB_CLK_EN 0x2c
+#define DSPA_CLK_CTRL0 0x30
+#define DSPB_CLK_CTRL0 0x34
+#define CLK12_24_CTRL 0x38
+#define GEN_CLK_CTRL 0x3c
+#define SAR_ADC_CLK_CTRL 0xc0
+#define PWM_CLK_AB_CTRL 0xc4
+#define PWM_CLK_CD_CTRL 0xc8
+#define PWM_CLK_EF_CTRL 0xcc
+#define SPICC_CLK_CTRL 0xd0
+#define TS_CLK_CTRL 0xd4
+#define SPIFC_CLK_CTRL 0xd8
+#define USB_BUSCLK_CTRL 0xdc
+#define SD_EMMC_CLK_CTRL 0xe0
+#define CECA_CLK_CTRL0 0xe4
+#define CECA_CLK_CTRL1 0xe8
+#define CECB_CLK_CTRL0 0xec
+#define CECB_CLK_CTRL1 0xf0
+#define PSRAM_CLK_CTRL 0xf4
+#define DMC_CLK_CTRL 0xf8
+
+/* include the CLKIDs that have been made part of the DT binding */
+#include <dt-bindings/clock/amlogic,a1-peripherals-clkc.h>
+
+/*
+ * CLKID index values for internal clocks
+ *
+ * These indices are entirely contrived and do not map onto the hardware.
+ * It has now been decided to expose everything by default in the DT header:
+ * include/dt-bindings/clock/a1-peripherals-clkc.h.
+ * Only the clocks ids we don't want to expose, such as the internal muxes and
+ * dividers of composite clocks, will remain defined here.
+ */
+#define CLKID_XTAL_IN 0
+#define CLKID_DSPA_SEL 61
+#define CLKID_DSPB_SEL 62
+#define CLKID_SARADC_SEL 74
+#define CLKID_SYS_A_SEL 89
+#define CLKID_SYS_A_DIV 90
+#define CLKID_SYS_A 91
+#define CLKID_SYS_B_SEL 92
+#define CLKID_SYS_B_DIV 93
+#define CLKID_SYS_B 94
+#define CLKID_DSPA_A_DIV 96
+#define CLKID_DSPA_A 97
+#define CLKID_DSPA_B_DIV 99
+#define CLKID_DSPA_B 100
+#define CLKID_DSPB_A_DIV 102
+#define CLKID_DSPB_A 103
+#define CLKID_DSPB_B_DIV 105
+#define CLKID_DSPB_B 106
+#define CLKID_RTC_32K_IN 107
+#define CLKID_RTC_32K_DIV 108
+#define CLKID_RTC_32K_XTAL 109
+#define CLKID_RTC_32K_SEL 110
+#define CLKID_CECB_32K_IN 111
+#define CLKID_CECB_32K_DIV 112
+#define CLKID_CECA_32K_IN 115
+#define CLKID_CECA_32K_DIV 116
+#define CLKID_DIV2_PRE 119
+#define CLKID_24M_DIV2 120
+#define CLKID_GEN_DIV 122
+#define CLKID_SARADC_DIV 123
+#define CLKID_PWM_A_DIV 125
+#define CLKID_PWM_B_DIV 127
+#define CLKID_PWM_C_DIV 129
+#define CLKID_PWM_D_DIV 131
+#define CLKID_PWM_E_DIV 133
+#define CLKID_PWM_F_DIV 135
+#define CLKID_SPICC_SEL 136
+#define CLKID_SPICC_DIV 137
+#define CLKID_SPICC_SEL2 138
+#define CLKID_TS_DIV 139
+#define CLKID_SPIFC_SEL 140
+#define CLKID_SPIFC_DIV 141
+#define CLKID_SPIFC_SEL2 142
+#define CLKID_USB_BUS_SEL 143
+#define CLKID_USB_BUS_DIV 144
+#define CLKID_SD_EMMC_SEL 145
+#define CLKID_SD_EMMC_DIV 146
+#define CLKID_PSRAM_SEL 148
+#define CLKID_PSRAM_DIV 149
+#define CLKID_PSRAM_SEL2 150
+#define CLKID_DMC_SEL 151
+#define CLKID_DMC_DIV 152
+#define CLKID_DMC_SEL2 153
+#define NR_CLKS 154
+
+#endif /* __A1_PERIPHERALS_H */
--
2.36.0
Hi Dmitry,
On Wed, May 17, 2023 at 3:33 PM Dmitry Rokosov <[email protected]> wrote:
[...]
> +static struct clk_regmap sys_b_sel = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = SYS_CLK_CTRL0,
> + .mask = 0x7,
> + .shift = 26,
> + .table = mux_table_sys,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "sys_b_sel",
> + .ops = &clk_regmap_mux_ro_ops,
the sys_*_sel muxes and sys_*_gate are _ro...
> + .parent_data = sys_parents,
> + .num_parents = ARRAY_SIZE(sys_parents),
> + },
> +};
> +
> +static struct clk_regmap sys_b_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = SYS_CLK_CTRL0,
> + .shift = 16,
> + .width = 10,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "sys_b_div",
> + .ops = &clk_regmap_divider_ops,
...but the sys_*_div aren't
Is this on purpose? If it is: why can the divider be changed at
runtime but the mux can't?
[...]
> +/*
> + * the index 2 is sys_pll_div16, it will be implemented in the CPU clock driver,
We need to add the "sys_pll_div16" input to the dt-bindings since they
should always describe the hardware (regardless of what the driver
implements currently).
I'm not sure how to manage this while we don't have the CPU clock
driver ready yet but I'm sure Rob or Krzysztof will be able to help us
here.
> + * the index 4 is the clock measurement source, it's not supported yet
I suspect that this comes from the clock measurer IP block and if so
the dt-bindings should probably describe this input. But again, we'd
need to keep it optional for now since our clock measurer driver
doesn't even implement a clock controller.
[...]
> +static struct clk_regmap pwm_a_sel = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = PWM_CLK_AB_CTRL,
> + .mask = 0x1,
> + .shift = 9,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "pwm_a_sel",
> + .ops = &clk_regmap_mux_ops,
> + .parent_data = pwm_abcd_parents,
> + .num_parents = ARRAY_SIZE(pwm_abcd_parents),
> + /* For more information, please refer to rtc clock */
> + .flags = CLK_SET_RATE_NO_REPARENT,
As mentioned in [0] we'll work with Heiner to see if we can improve
the decision making process of the PWM controller driver so that we
can just have .flags = 0 here.
This applies to all other occurrences of the same comment about the rtc clock.
Best regards,
Martin
Hello Martin,
Thank you so much for the review, I really appreciate it!
Please find my comments below.
On Fri, May 19, 2023 at 11:03:54PM +0200, Martin Blumenstingl wrote:
> Hi Dmitry,
>
> On Wed, May 17, 2023 at 3:33 PM Dmitry Rokosov <[email protected]> wrote:
> [...]
> > +static struct clk_regmap sys_b_sel = {
> > + .data = &(struct clk_regmap_mux_data){
> > + .offset = SYS_CLK_CTRL0,
> > + .mask = 0x7,
> > + .shift = 26,
> > + .table = mux_table_sys,
> > + },
> > + .hw.init = &(struct clk_init_data){
> > + .name = "sys_b_sel",
> > + .ops = &clk_regmap_mux_ro_ops,
> the sys_*_sel muxes and sys_*_gate are _ro...
>
> > + .parent_data = sys_parents,
> > + .num_parents = ARRAY_SIZE(sys_parents),
> > + },
> > +};
> > +
> > +static struct clk_regmap sys_b_div = {
> > + .data = &(struct clk_regmap_div_data){
> > + .offset = SYS_CLK_CTRL0,
> > + .shift = 16,
> > + .width = 10,
> > + },
> > + .hw.init = &(struct clk_init_data){
> > + .name = "sys_b_div",
> > + .ops = &clk_regmap_divider_ops,
> ...but the sys_*_div aren't
> Is this on purpose? If it is: why can the divider be changed at
> runtime but the mux can't?
>
Ah, that's a good catch. Since the system clock is set up by the BootROM
code, all sys_* dividers and gates should be read-only. I'll make sure
to change that in the next version.
> [...]
> > +/*
> > + * the index 2 is sys_pll_div16, it will be implemented in the CPU clock driver,
> We need to add the "sys_pll_div16" input to the dt-bindings since they
> should always describe the hardware (regardless of what the driver
> implements currently).
> I'm not sure how to manage this while we don't have the CPU clock
> driver ready yet but I'm sure Rob or Krzysztof will be able to help us
> here.
>
I've shared my thoughts about it in the bindings thread. Please take a
look.
> > + * the index 4 is the clock measurement source, it's not supported yet
> I suspect that this comes from the clock measurer IP block and if so
> the dt-bindings should probably describe this input. But again, we'd
> need to keep it optional for now since our clock measurer driver
> doesn't even implement a clock controller.
>
Indeed, this is a similar situation to what we have with the inputs and
clocks of the CPU and Audio clock controllers. It seems like there is
only one option here: we should mark it with a TODO tag...
> [...]
> > +static struct clk_regmap pwm_a_sel = {
> > + .data = &(struct clk_regmap_mux_data){
> > + .offset = PWM_CLK_AB_CTRL,
> > + .mask = 0x1,
> > + .shift = 9,
> > + },
> > + .hw.init = &(struct clk_init_data){
> > + .name = "pwm_a_sel",
> > + .ops = &clk_regmap_mux_ops,
> > + .parent_data = pwm_abcd_parents,
> > + .num_parents = ARRAY_SIZE(pwm_abcd_parents),
> > + /* For more information, please refer to rtc clock */
> > + .flags = CLK_SET_RATE_NO_REPARENT,
> As mentioned in [0] we'll work with Heiner to see if we can improve
> the decision making process of the PWM controller driver so that we
> can just have .flags = 0 here.
> This applies to all other occurrences of the same comment about the rtc clock.
Sure, I'll make the change in v16. In my opinion, we should remove the
CLK_SET_RATE_NO_REPARENT flag from all RTC related clock objects,
including PWM, regardless of the outcome of the Heiner discussion. Based
on our IRC talk, the decision has more pros than cons -
https://libera.irclog.whitequark.org/linux-amlogic/2023-05-18
--
Thank you,
Dmitry
On Mon 22 May 2023 at 16:32, Dmitry Rokosov <[email protected]> wrote:
> Hello Martin,
>
> Thank you so much for the review, I really appreciate it!
> Please find my comments below.
>
> On Fri, May 19, 2023 at 11:03:54PM +0200, Martin Blumenstingl wrote:
>> Hi Dmitry,
>>
>> On Wed, May 17, 2023 at 3:33 PM Dmitry Rokosov <[email protected]> wrote:
>> [...]
>> > +static struct clk_regmap sys_b_sel = {
>> > + .data = &(struct clk_regmap_mux_data){
>> > + .offset = SYS_CLK_CTRL0,
>> > + .mask = 0x7,
>> > + .shift = 26,
>> > + .table = mux_table_sys,
>> > + },
>> > + .hw.init = &(struct clk_init_data){
>> > + .name = "sys_b_sel",
>> > + .ops = &clk_regmap_mux_ro_ops,
>> the sys_*_sel muxes and sys_*_gate are _ro...
>>
>> > + .parent_data = sys_parents,
>> > + .num_parents = ARRAY_SIZE(sys_parents),
>> > + },
>> > +};
>> > +
>> > +static struct clk_regmap sys_b_div = {
>> > + .data = &(struct clk_regmap_div_data){
>> > + .offset = SYS_CLK_CTRL0,
>> > + .shift = 16,
>> > + .width = 10,
>> > + },
>> > + .hw.init = &(struct clk_init_data){
>> > + .name = "sys_b_div",
>> > + .ops = &clk_regmap_divider_ops,
>> ...but the sys_*_div aren't
>> Is this on purpose? If it is: why can the divider be changed at
>> runtime but the mux can't?
>>
>
> Ah, that's a good catch. Since the system clock is set up by the BootROM
> code, all sys_* dividers and gates should be read-only. I'll make sure
> to change that in the next version.
>
>> [...]
>> > +/*
>> > + * the index 2 is sys_pll_div16, it will be implemented in the CPU clock driver,
>> We need to add the "sys_pll_div16" input to the dt-bindings since they
>> should always describe the hardware (regardless of what the driver
>> implements currently).
>> I'm not sure how to manage this while we don't have the CPU clock
>> driver ready yet but I'm sure Rob or Krzysztof will be able to help us
>> here.
>>
>
> I've shared my thoughts about it in the bindings thread. Please take a
> look.
>
>> > + * the index 4 is the clock measurement source, it's not supported yet
>> I suspect that this comes from the clock measurer IP block and if so
>> the dt-bindings should probably describe this input. But again, we'd
>> need to keep it optional for now since our clock measurer driver
>> doesn't even implement a clock controller.
>>
>
> Indeed, this is a similar situation to what we have with the inputs and
> clocks of the CPU and Audio clock controllers. It seems like there is
> only one option here: we should mark it with a TODO tag...
>
>> [...]
>> > +static struct clk_regmap pwm_a_sel = {
>> > + .data = &(struct clk_regmap_mux_data){
>> > + .offset = PWM_CLK_AB_CTRL,
>> > + .mask = 0x1,
>> > + .shift = 9,
>> > + },
>> > + .hw.init = &(struct clk_init_data){
>> > + .name = "pwm_a_sel",
>> > + .ops = &clk_regmap_mux_ops,
>> > + .parent_data = pwm_abcd_parents,
>> > + .num_parents = ARRAY_SIZE(pwm_abcd_parents),
>> > + /* For more information, please refer to rtc clock */
>> > + .flags = CLK_SET_RATE_NO_REPARENT,
>> As mentioned in [0] we'll work with Heiner to see if we can improve
>> the decision making process of the PWM controller driver so that we
>> can just have .flags = 0 here.
>> This applies to all other occurrences of the same comment about the rtc clock.
>
> Sure, I'll make the change in v16. In my opinion, we should remove the
> CLK_SET_RATE_NO_REPARENT flag from all RTC related clock objects,
> including PWM, regardless of the outcome of the Heiner discussion. Based
> on our IRC talk, the decision has more pros than cons -
> https://libera.irclog.whitequark.org/linux-amlogic/2023-05-18
The clock scheme of PWM could indeed be handled like audio is but it
not strictly required.
In audio we have a limited number of PLLs (root sources). There is a lot
more consummers than there is root sources. If the root sources rate is
not carefully chosen to statisfy all needs, we could end in a situation
where we can't satisfy all consummers or we must glitch the source to do
so.
For the PWM, I think (but I'm not 100% sure) that the main clock controller
provides a source for each PWM. No risk of race there. That is why AML
decided to completly ignore the clock element in the PWM IP, because
they can do almost everything with what is in the main controller ... Still
ignoring those part is wrong
For the RTC, If you want/need to handle external RTCs, I don't think you
have much of a choice. If both the internal and external *report* the
same rate, CCF can't really know if one is best. It will just pick one,
no necessarily the one you want. I don't really see a way around manual
selection for this.
Hello Jerome,
Thank you for the review!
On Tue, May 30, 2023 at 10:32:57AM +0200, Jerome Brunet wrote:
>
> On Mon 22 May 2023 at 16:32, Dmitry Rokosov <[email protected]> wrote:
>
> > Hello Martin,
> >
> > Thank you so much for the review, I really appreciate it!
> > Please find my comments below.
> >
> > On Fri, May 19, 2023 at 11:03:54PM +0200, Martin Blumenstingl wrote:
> >> Hi Dmitry,
> >>
> >> On Wed, May 17, 2023 at 3:33 PM Dmitry Rokosov <[email protected]> wrote:
> >> [...]
> >> > +static struct clk_regmap sys_b_sel = {
> >> > + .data = &(struct clk_regmap_mux_data){
> >> > + .offset = SYS_CLK_CTRL0,
> >> > + .mask = 0x7,
> >> > + .shift = 26,
> >> > + .table = mux_table_sys,
> >> > + },
> >> > + .hw.init = &(struct clk_init_data){
> >> > + .name = "sys_b_sel",
> >> > + .ops = &clk_regmap_mux_ro_ops,
> >> the sys_*_sel muxes and sys_*_gate are _ro...
> >>
> >> > + .parent_data = sys_parents,
> >> > + .num_parents = ARRAY_SIZE(sys_parents),
> >> > + },
> >> > +};
> >> > +
> >> > +static struct clk_regmap sys_b_div = {
> >> > + .data = &(struct clk_regmap_div_data){
> >> > + .offset = SYS_CLK_CTRL0,
> >> > + .shift = 16,
> >> > + .width = 10,
> >> > + },
> >> > + .hw.init = &(struct clk_init_data){
> >> > + .name = "sys_b_div",
> >> > + .ops = &clk_regmap_divider_ops,
> >> ...but the sys_*_div aren't
> >> Is this on purpose? If it is: why can the divider be changed at
> >> runtime but the mux can't?
> >>
> >
> > Ah, that's a good catch. Since the system clock is set up by the BootROM
> > code, all sys_* dividers and gates should be read-only. I'll make sure
> > to change that in the next version.
> >
> >> [...]
> >> > +/*
> >> > + * the index 2 is sys_pll_div16, it will be implemented in the CPU clock driver,
> >> We need to add the "sys_pll_div16" input to the dt-bindings since they
> >> should always describe the hardware (regardless of what the driver
> >> implements currently).
> >> I'm not sure how to manage this while we don't have the CPU clock
> >> driver ready yet but I'm sure Rob or Krzysztof will be able to help us
> >> here.
> >>
> >
> > I've shared my thoughts about it in the bindings thread. Please take a
> > look.
> >
> >> > + * the index 4 is the clock measurement source, it's not supported yet
> >> I suspect that this comes from the clock measurer IP block and if so
> >> the dt-bindings should probably describe this input. But again, we'd
> >> need to keep it optional for now since our clock measurer driver
> >> doesn't even implement a clock controller.
> >>
> >
> > Indeed, this is a similar situation to what we have with the inputs and
> > clocks of the CPU and Audio clock controllers. It seems like there is
> > only one option here: we should mark it with a TODO tag...
> >
> >> [...]
> >> > +static struct clk_regmap pwm_a_sel = {
> >> > + .data = &(struct clk_regmap_mux_data){
> >> > + .offset = PWM_CLK_AB_CTRL,
> >> > + .mask = 0x1,
> >> > + .shift = 9,
> >> > + },
> >> > + .hw.init = &(struct clk_init_data){
> >> > + .name = "pwm_a_sel",
> >> > + .ops = &clk_regmap_mux_ops,
> >> > + .parent_data = pwm_abcd_parents,
> >> > + .num_parents = ARRAY_SIZE(pwm_abcd_parents),
> >> > + /* For more information, please refer to rtc clock */
> >> > + .flags = CLK_SET_RATE_NO_REPARENT,
> >> As mentioned in [0] we'll work with Heiner to see if we can improve
> >> the decision making process of the PWM controller driver so that we
> >> can just have .flags = 0 here.
> >> This applies to all other occurrences of the same comment about the rtc clock.
> >
> > Sure, I'll make the change in v16. In my opinion, we should remove the
> > CLK_SET_RATE_NO_REPARENT flag from all RTC related clock objects,
> > including PWM, regardless of the outcome of the Heiner discussion. Based
> > on our IRC talk, the decision has more pros than cons -
> > https://libera.irclog.whitequark.org/linux-amlogic/2023-05-18
>
> The clock scheme of PWM could indeed be handled like audio is but it
> not strictly required.
>
> In audio we have a limited number of PLLs (root sources). There is a lot
> more consummers than there is root sources. If the root sources rate is
> not carefully chosen to statisfy all needs, we could end in a situation
> where we can't satisfy all consummers or we must glitch the source to do
> so.
>
> For the PWM, I think (but I'm not 100% sure) that the main clock controller
> provides a source for each PWM. No risk of race there. That is why AML
> decided to completly ignore the clock element in the PWM IP, because
> they can do almost everything with what is in the main controller ... Still
> ignoring those part is wrong
>
> For the RTC, If you want/need to handle external RTCs, I don't think you
> have much of a choice. If both the internal and external *report* the
> same rate, CCF can't really know if one is best. It will just pick one,
> no necessarily the one you want. I don't really see a way around manual
> selection for this.
>
Per my understading, the rtc32k Amlogic clock is an internal clock and
cannot be an external one. Amlogic has provided it as an internal 32k
stable clock with low jitter.
You're absolutely right that there is no data available to confirm the
choice of an external RTC clock in the CCF. However, as per the approach
we discussed with Martin and Heiner, we can still use the RTC clock as a
parent for PWM in the current implementation. If the parent clock
already has 32k, we do not change the rate from the PWM driver. The
benefit of this approach is that reparenting is still available, but the
PWM child cannot change the RTC frequency; it simply uses the
appropriate parent clock. Additionally, if the parent is already set to
rtc32k, we shouldn't change it.
--
Thank you,
Dmitry
On Wed 17 May 2023 at 16:33, Dmitry Rokosov <[email protected]> wrote:
> A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
> and Audio. The audio clock controller is different from others, but the
> rest are very similar from a functional and regmap point of view.
> This patch series add support for Amlogic A1 PLL and Peripherals clock
> drivers.
> It blocks all A1 peripherals mainline support and a couple of patch series,
> which were already reviewed and acked, but weren't merged due to pending
> clock controller drivers series, e.g.
> https://lore.kernel.org/all/[email protected]/
>
> TODO: CPU and Audio clock controllers are not included in this patch
> series, it will be sent later. The following clks from these controllers
> are not supported for now:
> * Audio clks - vad, mclk_vad, mclk_d, resample_a, locker_in, mclk_b,
> pdmdclk, pdmsysclk, eqdrc, spdifin, mclk_a, audio2_toaudiotop,
> audio2_tovad, audio2_toddr_vad, audio2_tdmin_vad, audio2_pdm,
> audio2_ddr_arb, audio_audiolocker, audio_eqdrc, audio_resamplea,
> audio_spdifin, audio_toddrb, audio_toddra, audio_frddrb, audio_frddra,
> audio_tdmoutb, audio_tdmouta, audio_loopbacka, audio_tdminlb,
> audio_tdminb, audio_tdmina, audio_ddr_arb, mclk_c
>
> * CPU clks: cpu_fixed_source_sel0, cpu_fixed_source_div0,
> cpu_fixed_source_sel1, cpu_fixed_source_div1, cpu_clk
>
> Validation:
> * to double check all clk flags run below helper script:
> pushd /sys/kernel/debug/clk
> for f in *; do
> if [[ -f "$f/clk_flags" ]]; then
> flags="$(cat $f/clk_flags | awk '{$1=$1};1' | sed ':a;N;$!ba;s/\n/ | /g')"
> echo -e "$f: $flags"
> fi
> done
> popd
>
> * to trace current clks state use '/sys/kernel/debug/clk/clk_dump' node
> with jq post-processing:
> $ cat /sys/kernel/debug/clk/clk_dump | jq '.' > clk_dump.json
>
> * to debug clk rate propagation, compile kernel with the following
> definition:
> $ sed -i "s/undef CLOCK_ALLOW_WRITE_DEBUGFS/define CLOCK_ALLOW_WRITE_DEBUGFS/g" drivers/clk/clk.c
> after that, clk_rate debug node for each clock will be available for
> write operation
>
Applied, Thx
Jerome,
On Tue, May 30, 2023 at 06:14:01PM +0200, Jerome Brunet wrote:
> On Wed 17 May 2023 at 16:33, Dmitry Rokosov <[email protected]> wrote:
>
> > A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
> > and Audio. The audio clock controller is different from others, but the
> > rest are very similar from a functional and regmap point of view.
> > This patch series add support for Amlogic A1 PLL and Peripherals clock
> > drivers.
> > It blocks all A1 peripherals mainline support and a couple of patch series,
> > which were already reviewed and acked, but weren't merged due to pending
> > clock controller drivers series, e.g.
> > https://lore.kernel.org/all/[email protected]/
> >
> > TODO: CPU and Audio clock controllers are not included in this patch
> > series, it will be sent later. The following clks from these controllers
> > are not supported for now:
> > * Audio clks - vad, mclk_vad, mclk_d, resample_a, locker_in, mclk_b,
> > pdmdclk, pdmsysclk, eqdrc, spdifin, mclk_a, audio2_toaudiotop,
> > audio2_tovad, audio2_toddr_vad, audio2_tdmin_vad, audio2_pdm,
> > audio2_ddr_arb, audio_audiolocker, audio_eqdrc, audio_resamplea,
> > audio_spdifin, audio_toddrb, audio_toddra, audio_frddrb, audio_frddra,
> > audio_tdmoutb, audio_tdmouta, audio_loopbacka, audio_tdminlb,
> > audio_tdminb, audio_tdmina, audio_ddr_arb, mclk_c
> >
> > * CPU clks: cpu_fixed_source_sel0, cpu_fixed_source_div0,
> > cpu_fixed_source_sel1, cpu_fixed_source_div1, cpu_clk
> >
> > Validation:
> > * to double check all clk flags run below helper script:
> > pushd /sys/kernel/debug/clk
> > for f in *; do
> > if [[ -f "$f/clk_flags" ]]; then
> > flags="$(cat $f/clk_flags | awk '{$1=$1};1' | sed ':a;N;$!ba;s/\n/ | /g')"
> > echo -e "$f: $flags"
> > fi
> > done
> > popd
> >
> > * to trace current clks state use '/sys/kernel/debug/clk/clk_dump' node
> > with jq post-processing:
> > $ cat /sys/kernel/debug/clk/clk_dump | jq '.' > clk_dump.json
> >
> > * to debug clk rate propagation, compile kernel with the following
> > definition:
> > $ sed -i "s/undef CLOCK_ALLOW_WRITE_DEBUGFS/define CLOCK_ALLOW_WRITE_DEBUGFS/g" drivers/clk/clk.c
> > after that, clk_rate debug node for each clock will be available for
> > write operation
> >
>
> Applied, Thx
Thank you very much!
I noticed that you have applied version 15 of the patch. If I understand
correctly, this is because CLK_SET_RATE_NO_REPARENT for all RTC children
is preferred from your perspective. I agree with this decision. However,
version 16 includes a small refactoring patch that corrects a
misstyping by changing all sys_* related dividers and gates to
read-only operations, since they are set up from BootROM. Should I
submit this patch separately at a later time?
Also could you please clarify the official process for handling these
patches? Currently, I don't see them in the linux-amlogic for-next
branches. Is there a separate repository for clock changes? I believe
the next repository is a fork of the clock framework, but unfortunately,
I cannot seem to locate it on git.kernel.org... Apologies for the
potentially simple questions...
--
Thank you,
Dmitry
: , , . , , , , , , , . , , .
CONFIDENTIALITY NOTICE: This email and any files attached to it are confidential. If you are not the intended recipient you are notified that using, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. If you have received this email in error please notify the sender and delete this email.
Jerome,
On Tue, May 30, 2023 at 07:49:33PM +0300, Dmitry Rokosov wrote:
> Jerome,
>
> On Tue, May 30, 2023 at 06:14:01PM +0200, Jerome Brunet wrote:
> > On Wed 17 May 2023 at 16:33, Dmitry Rokosov <[email protected]> wrote:
> >
> > > A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
> > > and Audio. The audio clock controller is different from others, but the
> > > rest are very similar from a functional and regmap point of view.
> > > This patch series add support for Amlogic A1 PLL and Peripherals clock
> > > drivers.
> > > It blocks all A1 peripherals mainline support and a couple of patch series,
> > > which were already reviewed and acked, but weren't merged due to pending
> > > clock controller drivers series, e.g.
> > > https://lore.kernel.org/all/[email protected]/
> > >
> > > TODO: CPU and Audio clock controllers are not included in this patch
> > > series, it will be sent later. The following clks from these controllers
> > > are not supported for now:
> > > * Audio clks - vad, mclk_vad, mclk_d, resample_a, locker_in, mclk_b,
> > > pdmdclk, pdmsysclk, eqdrc, spdifin, mclk_a, audio2_toaudiotop,
> > > audio2_tovad, audio2_toddr_vad, audio2_tdmin_vad, audio2_pdm,
> > > audio2_ddr_arb, audio_audiolocker, audio_eqdrc, audio_resamplea,
> > > audio_spdifin, audio_toddrb, audio_toddra, audio_frddrb, audio_frddra,
> > > audio_tdmoutb, audio_tdmouta, audio_loopbacka, audio_tdminlb,
> > > audio_tdminb, audio_tdmina, audio_ddr_arb, mclk_c
> > >
> > > * CPU clks: cpu_fixed_source_sel0, cpu_fixed_source_div0,
> > > cpu_fixed_source_sel1, cpu_fixed_source_div1, cpu_clk
> > >
> > > Validation:
> > > * to double check all clk flags run below helper script:
> > > pushd /sys/kernel/debug/clk
> > > for f in *; do
> > > if [[ -f "$f/clk_flags" ]]; then
> > > flags="$(cat $f/clk_flags | awk '{$1=$1};1' | sed ':a;N;$!ba;s/\n/ | /g')"
> > > echo -e "$f: $flags"
> > > fi
> > > done
> > > popd
> > >
> > > * to trace current clks state use '/sys/kernel/debug/clk/clk_dump' node
> > > with jq post-processing:
> > > $ cat /sys/kernel/debug/clk/clk_dump | jq '.' > clk_dump.json
> > >
> > > * to debug clk rate propagation, compile kernel with the following
> > > definition:
> > > $ sed -i "s/undef CLOCK_ALLOW_WRITE_DEBUGFS/define CLOCK_ALLOW_WRITE_DEBUGFS/g" drivers/clk/clk.c
> > > after that, clk_rate debug node for each clock will be available for
> > > write operation
> > >
> >
> > Applied, Thx
>
> Thank you very much!
>
> I noticed that you have applied version 15 of the patch. If I understand
> correctly, this is because CLK_SET_RATE_NO_REPARENT for all RTC children
> is preferred from your perspective. I agree with this decision. However,
> version 16 includes a small refactoring patch that corrects a
> misstyping by changing all sys_* related dividers and gates to
> read-only operations, since they are set up from BootROM. Should I
> submit this patch separately at a later time?
>
> Also could you please clarify the official process for handling these
> patches? Currently, I don't see them in the linux-amlogic for-next
> branches. Is there a separate repository for clock changes? I believe
> the next repository is a fork of the clock framework, but unfortunately,
> I cannot seem to locate it on git.kernel.org... Apologies for the
> potentially simple questions...
I came across your development tree on GitHub, and I noticed that you've
applied the latest v16 version. Apologies for the noise!
https://github.com/BayLibre/clk-meson/commit/84af914404dbc01f388c440cac72428784b8a161#diff-9e8258bc44803391f868de351058eef033cf3828d52801e1711f786501bc5911
--
Thank you,
Dmitry
: , , . , , , , , , , . , , .
CONFIDENTIALITY NOTICE: This email and any files attached to it are confidential. If you are not the intended recipient you are notified that using, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited. If you have received this email in error please notify the sender and delete this email.