2023-06-12 08:21:28

by Markus Burri

[permalink] [raw]
Subject: [PATCH v1] iio: adc: ad7192: store indio_dev into spi driver data

After calibration the indio_dev is used to get channel information.
Since the pointer is not stored into spi driver data, there is a kernel
null pointer dereference.
Store the indio_dev into spi driver data to fix this.
Add error check and slightly extend the debug messages.

Signed-off-by: Markus Burri <[email protected]>
---
drivers/iio/adc/ad7192.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/iio/adc/ad7192.c b/drivers/iio/adc/ad7192.c
index d71977be7..7c2ead72b 100644
--- a/drivers/iio/adc/ad7192.c
+++ b/drivers/iio/adc/ad7192.c
@@ -403,8 +403,8 @@ static int ad7192_setup(struct ad7192_state *st, struct device_node *np)
id &= AD7192_ID_MASK;

if (id != st->chip_info->chip_id)
- dev_warn(&st->sd.spi->dev, "device ID query failed (0x%X)\n",
- id);
+ dev_warn(&st->sd.spi->dev, "device ID query failed (0x%X != 0x%X)\n",
+ id, st->chip_info->chip_id);

st->mode = AD7192_MODE_SEL(AD7192_MODE_IDLE) |
AD7192_MODE_CLKSRC(st->clock_sel) |
@@ -998,6 +998,7 @@ static int ad7192_probe(struct spi_device *spi)
return -ENOMEM;

st = iio_priv(indio_dev);
+ spi_set_drvdata(spi, indio_dev);

mutex_init(&st->lock);

@@ -1049,7 +1050,9 @@ static int ad7192_probe(struct spi_device *spi)
else
indio_dev->info = &ad7192_info;

- ad_sd_init(&st->sd, indio_dev, spi, &ad7192_sigma_delta_info);
+ ret = ad_sd_init(&st->sd, indio_dev, spi, &ad7192_sigma_delta_info);
+ if (ret)
+ return ret;

ret = devm_ad_sd_setup_buffer_and_trigger(&spi->dev, indio_dev);
if (ret)
@@ -1077,7 +1080,7 @@ static int ad7192_probe(struct spi_device *spi)
st->fclk = clk_get_rate(st->mclk);
if (!ad7192_valid_external_frequency(st->fclk)) {
dev_err(&spi->dev,
- "External clock frequency out of bounds\n");
+ "External clock frequency out of bounds (clk:%d)\n", st->fclk);
return -EINVAL;
}
}
--
2.39.2



2023-06-12 11:22:38

by Andy Shevchenko

[permalink] [raw]
Subject: Re: [PATCH v1] iio: adc: ad7192: store indio_dev into spi driver data

Mon, Jun 12, 2023 at 10:08:47AM +0200, Markus Burri kirjoitti:
> After calibration the indio_dev is used to get channel information.
> Since the pointer is not stored into spi driver data, there is a kernel
> null pointer dereference.
> Store the indio_dev into spi driver data to fix this.

This definitely deserves the Fixes tag. Can you dig the history to find the
culprit one?

> Add error check and slightly extend the debug messages.

I'm not sure this will belong to the same change, so I would split this out to
a separate one.

--
With Best Regards,
Andy Shevchenko