For the regulators, apply the same settings as in the downstream
devicetree [1], including the "regulator-always-on" for the SAFE_LDO.
For the voltage of SAFE_LDO, however, there is only one voltage of 4.9 V
available in the mainline driver [2][3].
The values of the battery data evolve from following sources:
- precharge current: 450 mA corresponds to the default value of the chip. It
doesn't get changed by the downstream Android driver. Therefore let's stick
to this value.
- constant charge current: The 1000 mA are taken from the downstream devicetree
of the serranove battery. It's not easy to spot. The value is in the line
"input_current_limit" [4]. The rows are according to the power supply type,
the 4th value stands for "main supply" [5]. That's the value used by the
Android driver when a charging cable is plugged into the device.
- charge termination current: In the downstream devicetree of the battery
that's the line "full_check_current_1st", which contains the 150 mA [6].
- precharge voltage: This one doesn't get set in the downstream Android driver.
The chip's default is 2.8 V. That seemed too low to have a notable effect of
handling the battery gentle. The chosen value of 3.5 V is a bit arbitrary
and possibly rather high. As the device is already several years old and
therefore most batteries too, a value on the safe side seems reasonable.
- constant charge voltage: The value of 4.35 V is set in the line
"chg_float_voltage" of the downstream battery devicetree [7].
The "connector" sub-node in the extcon node, the "battery" node in the
general section and the line "power-supplies" in the fuel-gauge node result
from the way of implementation documented in the dt-bindings of
rt5033-charger [8] and mfd rt5033 [9].
[1] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-eur-r03.dtsi#L135-L181
[2] https://github.com/torvalds/linux/blob/v6.3/include/linux/mfd/rt5033-private.h#L211-L212
[3] https://github.com/torvalds/linux/blob/v6.3/drivers/regulator/rt5033-regulator.c#L83
[4] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-battery-r01.dtsi#L100
[5] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/include/linux/power_supply.h#L173-L177
[6] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-battery-r01.dtsi#L102
[7] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/arch/arm/boot/dts/samsung/msm8916/msm8916-sec-serranovelte-battery-r01.dtsi#L95
[8] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/Documentation/devicetree/bindings/power/supply/richtek,rt5033-charger.yaml?h=next-20230616
[9] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/Documentation/devicetree/bindings/mfd/richtek,rt5033.yaml?h=next-20230616
Signed-off-by: Jakob Hauser <[email protected]>
---
The patch is based on linux-next "next-20230616".
The driver rt5033-charger was just recently added to linux-next.
.../dts/qcom/msm8916-samsung-serranove.dts | 67 ++++++++++++++++++-
1 file changed, 66 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
index 15dc246e84e2..2114d26548db 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
@@ -142,6 +142,12 @@ muic: extcon@14 {
pinctrl-names = "default";
pinctrl-0 = <&muic_irq_default>;
+
+ usb_con: connector {
+ compatible = "usb-b-connector";
+ label = "micro-USB";
+ type = "micro";
+ };
};
};
@@ -199,6 +205,15 @@ nfc@2b {
pinctrl-0 = <&nfc_default>;
};
};
+
+ battery: battery {
+ compatible = "simple-battery";
+ precharge-current-microamp = <450000>;
+ constant-charge-current-max-microamp = <1000000>;
+ charge-term-current-microamp = <150000>;
+ precharge-upper-limit-microvolt = <3500000>;
+ constant-charge-voltage-max-microvolt = <4350000>;
+ };
};
&blsp_i2c2 {
@@ -228,7 +243,7 @@ magnetometer@2e {
&blsp_i2c4 {
status = "okay";
- battery@35 {
+ fuel-gauge@35 {
compatible = "richtek,rt5033-battery";
reg = <0x35>;
@@ -237,6 +252,8 @@ battery@35 {
pinctrl-names = "default";
pinctrl-0 = <&fg_alert_default>;
+
+ power-supplies = <&rt5033_charger>;
};
};
@@ -261,6 +278,46 @@ touchscreen@20 {
};
};
+&blsp_i2c6 {
+ status = "okay";
+
+ pmic@34 {
+ compatible = "richtek,rt5033";
+ reg = <0x34>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <62 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_default>;
+
+ regulators {
+ safe_ldo_reg: SAFE_LDO {
+ regulator-name = "SAFE_LDO";
+ regulator-min-microvolt = <4900000>;
+ regulator-max-microvolt = <4900000>;
+ regulator-always-on;
+ };
+ ldo_reg: LDO {
+ regulator-name = "LDO";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ buck_reg: BUCK {
+ regulator-name = "BUCK";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ };
+
+ rt5033_charger: charger {
+ compatible = "richtek,rt5033-charger";
+ monitored-battery = <&battery>;
+ richtek,usb-connector = <&usb_con>;
+ };
+ };
+};
+
&blsp_uart2 {
status = "okay";
};
@@ -387,6 +444,14 @@ nfc_i2c_default: nfc-i2c-default-state {
bias-disable;
};
+ pmic_int_default: pmic-int-default-state {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
tkey_default: tkey-default-state {
pins = "gpio98";
function = "gpio";
--
2.39.2