2023-07-04 16:44:00

by David Wronek

Subject: [PATCH 5/7] arm64: dts: qcom: pm6150: Add resin and rtc nodes

Add support for the RTC which is the same as on other PMICs and add the
resin child node to the PM6150 PON device and disable it by default.

Signed-off-by: David Wronek <[email protected]>
---
arch/arm64/boot/dts/qcom/pm6150.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
index 2e6afa296141..9a7c532f7a12 100644
--- a/arch/arm64/boot/dts/qcom/pm6150.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
@@ -53,6 +53,14 @@ pm6150_pwrkey: pwrkey {
bias-pull-up;
linux,code = <KEY_POWER>;
};
+
+ pm6150_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ status = "disabled";
+ };
};

pm6150_temp: temp-alarm@2400 {
@@ -88,6 +96,13 @@ pm6150_adc_tm: adc-tm@3500 {
status = "disabled";
};

+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>, <0x6100>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ };
+
pm6150_gpios: gpio@c000 {
compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
--
2.41.0

2023-07-04 18:26:06

by Konrad Dybcio

Subject: Re: [PATCH 5/7] arm64: dts: qcom: pm6150: Add resin and rtc nodes

On 4.07.2023 18:31, David Wronek wrote:
> Add support for the RTC which is the same as on other PMICs and add the
> resin child node to the PM6150 PON device and disable it by default.
>
> Signed-off-by: David Wronek <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/pm6150.dtsi | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> index 2e6afa296141..9a7c532f7a12 100644
> --- a/arch/arm64/boot/dts/qcom/pm6150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
> @@ -53,6 +53,14 @@ pm6150_pwrkey: pwrkey {
> bias-pull-up;
> linux,code = <KEY_POWER>;
> };
> +
> + pm6150_resin: resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
0x0 (GIC_SPI is a property of the ARM GIC, SPMI uses the interrupts
field in a rather hacky and specific way)

[...]

> + rtc@6000 {
> + compatible = "qcom,pm8941-rtc";
> + reg = <0x6000>, <0x6100>;
> + reg-names = "rtc", "alarm";
> + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
IRQ_TYPE_EDGE_RISING

Konrad
> + };
> +
> pm6150_gpios: gpio@c000 {
> compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
> reg = <0xc000>;