GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
index d1f343345f67..6464ef4d113d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
@@ -773,7 +773,7 @@ brcmf: wifi@1 {
compatible = "brcm,bcm4329-fmac";
reg = <1>;
interrupt-parent = <&gpio0>;
- interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "host-wake";
pinctrl-names = "default";
pinctrl-0 = <&wifi_host_wake_l>;
--
2.34.1
On 05/07/2023 08:48, Krzysztof Kozlowski wrote:
> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
> These are simple defines so they could be used in DTS but they will not
> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
>
> Correct the interrupt flags, assuming the author of the code wanted same
> logical behavior behind the name "ACTIVE_xxx", this is:
> ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
This should be HIGH in both cases. I will send a v2.
>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
> ---
> arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> index d1f343345f67..6464ef4d113d 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> @@ -773,7 +773,7 @@ brcmf: wifi@1 {
> compatible = "brcm,bcm4329-fmac";
> reg = <1>;
> interrupt-parent = <&gpio0>;
> - interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
Best regards,
Krzysztof
On 2023-07-06 14:54, Krzysztof Kozlowski wrote:
> On 05/07/2023 08:48, Krzysztof Kozlowski wrote:
>> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
>> These are simple defines so they could be used in DTS but they will not
>> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
>>
>> Correct the interrupt flags, assuming the author of the code wanted same
>> logical behavior behind the name "ACTIVE_xxx", this is:
>> ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
>
> This should be HIGH in both cases. I will send a v2.
Also the titles say "audio-codec" but they're all touching SDIO WiFi
modules ;)
Cheers,
Robin.
>>
>> Signed-off-by: Krzysztof Kozlowski <[email protected]>
>> ---
>> arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +-
>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>> index d1f343345f67..6464ef4d113d 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>> @@ -773,7 +773,7 @@ brcmf: wifi@1 {
>> compatible = "brcm,bcm4329-fmac";
>> reg = <1>;
>> interrupt-parent = <&gpio0>;
>> - interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
>> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
>
> Best regards,
> Krzysztof
>
>
> _______________________________________________
> Linux-rockchip mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
On 06/07/2023 19:49, Robin Murphy wrote:
> On 2023-07-06 14:54, Krzysztof Kozlowski wrote:
>> On 05/07/2023 08:48, Krzysztof Kozlowski wrote:
>>> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
>>> These are simple defines so they could be used in DTS but they will not
>>> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
>>>
>>> Correct the interrupt flags, assuming the author of the code wanted same
>>> logical behavior behind the name "ACTIVE_xxx", this is:
>>> ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
>>
>> This should be HIGH in both cases. I will send a v2.
>
> Also the titles say "audio-codec" but they're all touching SDIO WiFi
> modules ;)
Thanks. Too much of copy-pasta.
Best regards,
Krzysztof