From: Patrick Rudolph <[email protected]>
This patch adds support for an optional reset pin.
The reset pin is used to bring the chip into a known state and has an
internal pull-down, allowing it to be left floating if not needed.
Signed-off-by: Patrick Rudolph <[email protected]>
Signed-off-by: Naresh Solanki <[email protected]>
---
Changes in V3:
- Update reset-gpios description.
Changes in V2:
- Update subject
- Update reset-gpios description.
---
.../devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml
index 222d57541b65..7f30ec2f1e54 100644
--- a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml
@@ -51,6 +51,10 @@ properties:
description:
Optional power supply.
+ reset-gpios:
+ description: GPIO connected to the XRES pin
+ maxItems: 1
+
patternProperties:
'-pins$':
type: object
base-commit: 3bc551a3007a751a53bfba5b37fa16157f4fb861
--
2.41.0
From: Patrick Rudolph <[email protected]>
This patch adds support for an optional "reset" GPIO pin in the cy8c95x0
pinctrl driver. On probe, the reset pin is pulled low to bring chip out
of reset. The reset pin has an internal pull-down and can be left
floating if not required.
The datasheet doesn't mention any timing related to the reset pin.
Based on empirical tests, it was found that the chip requires a
delay of 250 milliseconds before accepting I2C transfers after driving
the reset pin low. Therefore, a delay of 250ms is added before
proceeding with I2C transfers.
Signed-off-by: Patrick Rudolph <[email protected]>
Signed-off-by: Naresh Solanki <[email protected]>
---
Changes in V2:
- None
---
drivers/pinctrl/pinctrl-cy8c95x0.c | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/drivers/pinctrl/pinctrl-cy8c95x0.c b/drivers/pinctrl/pinctrl-cy8c95x0.c
index 2ecc96691c55..58ca6fac7849 100644
--- a/drivers/pinctrl/pinctrl-cy8c95x0.c
+++ b/drivers/pinctrl/pinctrl-cy8c95x0.c
@@ -164,6 +164,7 @@ struct cy8c95x0_pinctrl {
struct pinctrl_desc pinctrl_desc;
char name[32];
unsigned int tpin;
+ struct gpio_desc *gpio_reset;
};
static const struct pinctrl_pin_desc cy8c9560_pins[] = {
@@ -1383,6 +1384,20 @@ static int cy8c95x0_probe(struct i2c_client *client)
chip->regulator = reg;
}
+ /* bring the chip out of reset if reset pin is provided */
+ chip->gpio_reset = devm_gpiod_get_optional(&client->dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(chip->gpio_reset)) {
+ ret = dev_err_probe(chip->dev, PTR_ERR(chip->gpio_reset),
+ "Failed to get GPIO 'reset'\n");
+ goto err_exit;
+ } else if (chip->gpio_reset) {
+ usleep_range(1000, 2000);
+ gpiod_set_value_cansleep(chip->gpio_reset, 0);
+ usleep_range(250000, 300000);
+
+ gpiod_set_consumer_name(chip->gpio_reset, "CY8C95X0 RESET");
+ }
+
chip->regmap = devm_regmap_init_i2c(client, &cy8c95x0_i2c_regmap);
if (IS_ERR(chip->regmap)) {
ret = PTR_ERR(chip->regmap);
--
2.41.0
On 14/07/2023 10:19, Naresh Solanki wrote:
> From: Patrick Rudolph <[email protected]>
>
> This patch adds support for an optional reset pin.
>
> The reset pin is used to bring the chip into a known state and has an
> internal pull-down, allowing it to be left floating if not needed.
>
> Signed-off-by: Patrick Rudolph <[email protected]>
> Signed-off-by: Naresh Solanki <[email protected]>
> ---
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
Hi Naresh!
On Fri, Jul 14, 2023 at 10:19 AM Naresh Solanki
<[email protected]> wrote:
> From: Patrick Rudolph <[email protected]>
>
> This patch adds support for an optional reset pin.
>
> The reset pin is used to bring the chip into a known state and has an
> internal pull-down, allowing it to be left floating if not needed.
>
> Signed-off-by: Patrick Rudolph <[email protected]>
> Signed-off-by: Naresh Solanki <[email protected]>
Both patches applied!
Yours,
Linus Walleij
Fri, Jul 14, 2023 at 10:19:01AM +0200, Naresh Solanki kirjoitti:
> From: Patrick Rudolph <[email protected]>
>
> This patch adds support for an optional "reset" GPIO pin in the cy8c95x0
Find "This patch" in the Submitting Patches documentation and modify this
accordingly.
> pinctrl driver. On probe, the reset pin is pulled low to bring chip out
> of reset. The reset pin has an internal pull-down and can be left
> floating if not required.
>
> The datasheet doesn't mention any timing related to the reset pin.
>
> Based on empirical tests, it was found that the chip requires a
> delay of 250 milliseconds before accepting I2C transfers after driving
> the reset pin low. Therefore, a delay of 250ms is added before
> proceeding with I2C transfers.
...
> + /* bring the chip out of reset if reset pin is provided */
> + chip->gpio_reset = devm_gpiod_get_optional(&client->dev, "reset", GPIOD_OUT_HIGH);
&client->dev
> + if (IS_ERR(chip->gpio_reset)) {
> + ret = dev_err_probe(chip->dev, PTR_ERR(chip->gpio_reset),
chip->dev
Why inconsistent?
> + "Failed to get GPIO 'reset'\n");
> + goto err_exit;
I haven't looked at the context, but this seems like a smoke, we usually don't
have such in devm-enabled drivers.
> + } else if (chip->gpio_reset) {
> + usleep_range(1000, 2000);
> + gpiod_set_value_cansleep(chip->gpio_reset, 0);
> + usleep_range(250000, 300000);
This is incorrect use of usleep_range(). Please, read documentation
Documentation/timers/timers-howto.rst on the topic. The fix can be switching to
fsleep() in both branches.
> + gpiod_set_consumer_name(chip->gpio_reset, "CY8C95X0 RESET");
This can be done uncoditionally before toggling the reset.
> + }
...
This change wasn't Cc'ed to me, however I was contributing a lot into this driver.
I would recommend to use my "smart" script [1] to send patches. It has some
heuristics which works well in 98% of the cases for me.
[1]: https://github.com/andy-shev/home-bin-tools/blob/master/ge2maintainer.sh
--
With Best Regards,
Andy Shevchenko