CAN instances 3 and 5 in the main domain are brought on the common
processor board through header J27 and J28. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceivers on
the common processor board. Threfore, add respective mux, transceiver
dt nodes to add support for these CAN instances.
Reviewed-by: Udit Kumar <[email protected]>
Signed-off-by: Bhavya Kapoor <[email protected]>
---
Changelog v4->v5 : Modfied Mux Controller names
Link to v4 : https://lore.kernel.org/all/[email protected]/
.../dts/ti/k3-j721s2-common-proc-board.dts | 46 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 12 +++++
2 files changed, 58 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 04d4739d7245..e715fa12f9ca 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -29,6 +29,8 @@ aliases {
can0 = &main_mcan16;
can1 = &mcu_mcan0;
can2 = &mcu_mcan1;
+ can3 = &main_mcan3;
+ can4 = &main_mcan5;
};
evm_12v0: fixedregulator-evm12v0 {
@@ -109,6 +111,22 @@ transceiver2: can-phy2 {
standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
};
+ transceiver3: can-phy3 {
+ compatible = "ti,tcan1043";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+ mux-states = <&mux0 1>;
+ };
+
+ transceiver4: can-phy4 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&exp_som 7 GPIO_ACTIVE_HIGH>;
+ mux-states = <&mux1 1>;
+ };
};
&main_pmx0 {
@@ -152,6 +170,20 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
>;
};
+
+ main_mcan3_pins_default: main-mcan3-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x080, PIN_INPUT, 0) /* (U26) MCASP0_AXR4.MCAN3_RX */
+ J721S2_IOPAD(0x07c, PIN_OUTPUT, 0) /* (T27) MCASP0_AXR3.MCAN3_TX */
+ >;
+ };
+
+ main_mcan5_pins_default: main-mcan5-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x03c, PIN_INPUT, 0) /* (U27) MCASP0_AFSX.MCAN5_RX */
+ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */
+ >;
+ };
};
&wkup_pmx2 {
@@ -460,3 +492,17 @@ adc {
ti,adc-channels = <0 1 2 3 4 5 6 7>;
};
};
+
+&main_mcan3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan3_pins_default>;
+ phys = <&transceiver3>;
+};
+
+&main_mcan5 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan5_pins_default>;
+ phys = <&transceiver4>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index d57dd43da0ef..594766482071 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -31,6 +31,18 @@ secure_ddr: optee@9e800000 {
};
};
+ mux0: mux-controller {
+ compatible = "gpio-mux";
+ #mux-state-cells = <1>;
+ mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ mux1: mux-controller {
+ compatible = "gpio-mux";
+ #mux-state-cells = <1>;
+ mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>;
+ };
+
transceiver0: can-phy0 {
/* standby pin has been grounded by default */
compatible = "ti,tcan1042";
--
2.34.1
On 16:47-20230724, Bhavya Kapoor wrote:
> + main_mcan3_pins_default: main-mcan3-pins-default {
Could you make sure that the node names matches up with the json-schema
conversion:
https://lore.kernel.org/all/[email protected]/
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D