The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like the implementation
of custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
The subsystem includes many accelerators for data processing like
multiplier and multiplier-accumulator. It also has peripherals like
UART, MII/RGMII, MDIO, etc. Every ICSSG core includes two 32-bit
load/store RISC CPU cores called PRUs.
The above features allow it to be used for implementing custom firmware
based peripherals like ethernet.
This series adds the YAML documentation and the driver with basic EMAC
support for TI AM654 Silicon Rev 2 SoC with the PRU_ICSSG Sub-system.
running dual-EMAC firmware.
This currently supports basic EMAC with 1Gbps and 100Mbps link. 10M and
half-duplex modes are not yet supported because they require the support
of an IEP, which will be added later.
Advanced features like switch-dev and timestamping will be added later.
This is the v13 of the patch series [v1]. This version of the patchset
addresses comments made on v12.
There series doesn't have any dependency.
Changes from v12 to v13 :
*) Rebased the series on latest net-next.
*) Addressed Jakub's comments on ndo_xmit API. Now we will only stop queues
based on occupancy not on dma errors.
*) Removed limiting the number of serviced packets to budget for Tx NAPI.
Now Tx NAPI will keep servicing packets.
*) Removed netif_running() check when packet arrives.
*) Introduced prototypes of APIs in the same patch where these APIs are added.
Dropped __maybe_unused tags as compiler only cares about prototypes
existing, not whether actual callers are in place. Now prototypes of these
APIs are present in the same patch where they are introduced but thes APIs
are called later (in patch 6).
Changes from v11 to v12 :
*) Rebased the series on latest net-next.
*) Addressed Jakub's comments on ndo_xmit API.
*) Added hooks to .get_rmon_stats for the driver. Now tx / rx bucket size
and frame counts per bucket will be fetched by ethtool_rmon_stats instead
of ethtool -S.
*) Added __maybe_unused tags to unused config and classifier APIs in patch
2,3 and 4. These tags are later removed in patch 6.
Changes from v10 to v11 :
*) Rebased the series on latest net-next.
*) Split the ICSSG driver introduction patch into 9 different patches as
asked by Jakub.
*) Introduced new patch(patch 8/10) to dump Standard network interface
staticstics via ndo_get_stats64. Now certain stats that are reported by
ICSSG hardware and are also part of struct rtnl_link_stats64, will be
reported by ndo_get_stats64. While other stats that are not part of the
struct rtnl_link_stats64 will be reported by ethtool -S. These stats
are not duplicated.
Changes from v9 to v10 :
*) Rebased the series on latest net-next.
*) Moved 'ndev prueth->emac[mac] == emac' assignment to the end of function
prueth_netdev_init().
*) In unsupported phy_mode switch case instead of returning -EINVAL, store
the error code in ret and 'goto free'
Changes from v8 to v9 :
*) Rebased the series on latest net-next.
*) Fixed smatch and sparse warnings as pointed by Simon.
*) Fixed leaky ndev in prueth_netdev_init() as asked by Simon.
Changes from v7 to v8 :
*) Rebased the series on 6.5-rc1.
*) Fixed few formattings.
Changes from v6 to v7 :
*) Added RB tag of Rob in patch 1 of this series.
*) Addressed Simon's comment on patch 2 of the series.
*) Rebased patchset on next-20230428 linux-next.
Changes from v5 to v6 :
*) Added RB tag of Andrew Lunn in patch 2 of this series.
*) Addressed Rob's comment on patch 1 of the series.
*) Rebased patchset on next-20230421 linux-next.
Changes from v4 to v5 :
*) Re-arranged properties section in ti,icssg-prueth.yaml file.
*) Added requirement for minimum one ethernet port.
*) Fixed some minor formatting errors as asked by Krzysztof.
*) Dropped SGMII mode from enum mii_mode as SGMII mode is not currently
supported by the driver.
*) Added switch-case block to handle different phy modes by ICSSG driver.
Changes from v3 to v4 :
*) Addressed Krzysztof's comments and fixed dt_binding_check errors in
patch 1/2.
*) Added interrupt-extended property in ethernet-ports properties section.
*) Fixed comments in file icssg_switch_map.h according to the Linux coding
style in patch 2/2. Added Documentation of structures in patch 2/2.
Changes from v2 to v3 :
*) Addressed Rob and Krzysztof's comments on patch 1 of this series.
Fixed indentation. Removed description and pinctrl section from
ti,icssg-prueth.yaml file.
*) Addressed Krzysztof, Paolo, Randy, Andrew and Christophe's comments on
patch 2 of this seires.
*) Fixed blanklines in Kconfig and Makefile. Changed structures to const
as suggested by Krzysztof.
*) Fixed while loop logic in emac_tx_complete_packets() API as suggested
by Paolo. Previously in the loop's last iteration 'budget' was 0 and
napi_consume_skb would wrongly assume the caller is not in NAPI context
Now, budget won't be zero in last iteration of loop.
*) Removed inline functions addr_to_da1() and addr_to_da0() as asked by
Andrew.
*) Added dev_err_probe() instead of dev_err() as suggested by Christophe.
*) In ti,icssg-prueth.yaml file, in the patternProperties section of
ethernet-ports, kept the port name as "port" instead of "ethernet-port"
as all other drivers were using "port". Will change it if is compulsory
to use "ethernet-port".
[v1] https://lore.kernel.org/all/[email protected]/
[v2] https://lore.kernel.org/all/[email protected]/
[v3] https://lore.kernel.org/all/[email protected]/
[v4] https://lore.kernel.org/all/[email protected]/
[v5] https://lore.kernel.org/all/[email protected]/
[v6] https://lore.kernel.org/all/[email protected]/
[v7] https://lore.kernel.org/all/[email protected]/
[v8] https://lore.kernel.org/all/[email protected]/
[v9] https://lore.kernel.org/all/[email protected]/
[v10] https://lore.kernel.org/all/[email protected]/
[v11] https://lore.kernel.org/netdev/[email protected]/
[v12] https://lore.kernel.org/all/[email protected]/
Thanks and Regards,
Md Danish Anwar
MD Danish Anwar (9):
net: ti: icssg-prueth: Add Firmware Interface for ICSSG Ethernet
driver.
net: ti: icssg-prueth: Add mii helper apis and macros
net: ti: icssg-prueth: Add Firmware config and classification APIs.
net: ti: icssg-prueth: Add icssg queues APIs and macros
dt-bindings: net: Add ICSSG Ethernet
net: ti: icssg-prueth: Add ICSSG Stats
net: ti: icssg-prueth: Add Standard network staticstics
net: ti: icssg-prueth: Add ethtool ops for ICSSG Ethernet driver
net: ti: icssg-prueth: Add Power management support
Roger Quadros (1):
net: ti: icssg-prueth: Add ICSSG ethernet driver
.../bindings/net/ti,icssg-prueth.yaml | 184 ++
drivers/net/ethernet/ti/Kconfig | 13 +
drivers/net/ethernet/ti/Makefile | 10 +
.../net/ethernet/ti/icssg/icssg_classifier.c | 367 ++++
drivers/net/ethernet/ti/icssg/icssg_config.c | 450 ++++
drivers/net/ethernet/ti/icssg/icssg_config.h | 200 ++
drivers/net/ethernet/ti/icssg/icssg_ethtool.c | 188 ++
drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c | 120 ++
drivers/net/ethernet/ti/icssg/icssg_mii_rt.h | 151 ++
drivers/net/ethernet/ti/icssg/icssg_prueth.c | 1897 +++++++++++++++++
drivers/net/ethernet/ti/icssg/icssg_prueth.h | 262 +++
drivers/net/ethernet/ti/icssg/icssg_queues.c | 50 +
drivers/net/ethernet/ti/icssg/icssg_stats.c | 57 +
drivers/net/ethernet/ti/icssg/icssg_stats.h | 158 ++
.../net/ethernet/ti/icssg/icssg_switch_map.h | 234 ++
15 files changed, 4341 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_classifier.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_config.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_config.h
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_ethtool.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_mii_rt.h
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_prueth.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_prueth.h
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_queues.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_stats.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_stats.h
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_switch_map.h
--
2.34.1
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
---
.../net/ethernet/ti/icssg/icssg_switch_map.h | 234 ++++++++++++++++++
1 file changed, 234 insertions(+)
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_switch_map.h
diff --git a/drivers/net/ethernet/ti/icssg/icssg_switch_map.h b/drivers/net/ethernet/ti/icssg/icssg_switch_map.h
new file mode 100644
index 000000000000..424a7e945ea8
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_switch_map.h
@@ -0,0 +1,234 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_SWITCH_MAP_H
+#define __NET_TI_ICSSG_SWITCH_MAP_H
+
+/************************* Ethernet Switch Constants *********************/
+
+/* if bucket size is changed in firmware then this too should be changed
+ * because it directly impacts FDB ageing calculation
+ */
+#define NUMBER_OF_FDB_BUCKET_ENTRIES (4)
+
+/* This is fixed in ICSSG */
+#define SIZE_OF_FDB (2048)
+
+#define FW_LINK_SPEED_1G (0x00)
+#define FW_LINK_SPEED_100M (0x01)
+#define FW_LINK_SPEED_10M (0x02)
+#define FW_LINK_SPEED_HD (0x80)
+
+/* Time after which FDB entries are checked for aged out values.
+ * Values are in nanoseconds
+ */
+#define FDB_AGEING_TIMEOUT_OFFSET 0x0014
+
+/* Default VLAN tag for Host Port */
+#define HOST_PORT_DF_VLAN_OFFSET 0x001C
+
+/* Same as HOST_PORT_DF_VLAN_OFFSET */
+#define EMAC_ICSSG_SWITCH_PORT0_DEFAULT_VLAN_OFFSET HOST_PORT_DF_VLAN_OFFSET
+
+/* Default VLAN tag for P1 Port */
+#define P1_PORT_DF_VLAN_OFFSET 0x0020
+
+/* Same as P1_PORT_DF_VLAN_OFFSET */
+#define EMAC_ICSSG_SWITCH_PORT1_DEFAULT_VLAN_OFFSET P1_PORT_DF_VLAN_OFFSET
+
+/* default VLAN tag for P2 Port */
+#define P2_PORT_DF_VLAN_OFFSET 0x0024
+
+/* Same as P2_PORT_DF_VLAN_OFFSET */
+#define EMAC_ICSSG_SWITCH_PORT2_DEFAULT_VLAN_OFFSET P2_PORT_DF_VLAN_OFFSET
+
+/* VLAN-FID Table offset. 4096 VIDs. 2B per VID = 8KB = 0x2000 */
+#define VLAN_STATIC_REG_TABLE_OFFSET 0x0100
+
+/* VLAN-FID Table offset for EMAC */
+#define EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET VLAN_STATIC_REG_TABLE_OFFSET
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC0_HI 0x2104
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC0_LO 0x2F6C
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC1_HI 0x3DD4
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC1_LO 0x4C3C
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC0_HI 0x5AA4
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC0_LO 0x5F0C
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC1_HI 0x6374
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC1_LO 0x67DC
+
+/* Special packet descriptor Q reserved memory */
+#define HOST_SPPD0 0x7AAC
+
+/* Special acket descriptor Q reserved memory */
+#define HOST_SPPD1 0x7EAC
+
+/* IEP count cycle counter*/
+#define TIMESYNC_FW_WC_CYCLECOUNT_OFFSET 0x83EC
+
+/* IEP count hi roll over count */
+#define TIMESYNC_FW_WC_HI_ROLLOVER_COUNT_OFFSET 0x83F4
+
+/* IEP count hi sw counter */
+#define TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET 0x83F8
+
+/* Set clock descriptor */
+#define TIMESYNC_FW_WC_SETCLOCK_DESC_OFFSET 0x83FC
+
+/* IEP count syncout reduction factor */
+#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_FACTOR_OFFSET 0x843C
+
+/* IEP count syncout reduction counter */
+#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_COUNT_OFFSET 0x8440
+
+/* IEP count syncout start time cycle counter */
+#define TIMESYNC_FW_WC_SYNCOUT_START_TIME_CYCLECOUNT_OFFSET 0x8444
+
+/* Control variable to generate SYNC1 */
+#define TIMESYNC_FW_WC_ISOM_PIN_SIGNAL_EN_OFFSET 0x844C
+
+/* SystemTime Sync0 periodicity */
+#define TIMESYNC_FW_ST_SYNCOUT_PERIOD_OFFSET 0x8450
+
+/* pktTxDelay for P1 = link speed dependent p1 mac delay + p1 phy delay */
+#define TIMESYNC_FW_WC_PKTTXDELAY_P1_OFFSET 0x8454
+
+/* pktTxDelay for P2 = link speed dependent p2 mac delay + p2 phy delay */
+#define TIMESYNC_FW_WC_PKTTXDELAY_P2_OFFSET 0x8458
+
+/* Set clock operation done signal for next task */
+#define TIMESYNC_FW_SIG_PNFW_OFFSET 0x845C
+
+/* Set clock operation done signal for next task */
+#define TIMESYNC_FW_SIG_TIMESYNCFW_OFFSET 0x8460
+
+/* New list is copied at this time */
+#define TAS_CONFIG_CHANGE_TIME 0x000C
+
+/* config change error counter */
+#define TAS_CONFIG_CHANGE_ERROR_COUNTER 0x0014
+
+/* TAS List update pending flag */
+#define TAS_CONFIG_PENDING 0x0018
+
+/* TAS list update trigger flag */
+#define TAS_CONFIG_CHANGE 0x0019
+
+/* List length for new TAS schedule */
+#define TAS_ADMIN_LIST_LENGTH 0x001A
+
+/* Currently active TAS list index */
+#define TAS_ACTIVE_LIST_INDEX 0x001B
+
+/* Cycle time for the new TAS schedule */
+#define TAS_ADMIN_CYCLE_TIME 0x001C
+
+/* Cycle counts remaining till the TAS list update */
+#define TAS_CONFIG_CHANGE_CYCLE_COUNT 0x0020
+
+/* Base Flow ID for sending Packets to Host for Slice0 */
+#define PSI_L_REGULAR_FLOW_ID_BASE_OFFSET 0x0024
+
+/* Same as PSI_L_REGULAR_FLOW_ID_BASE_OFFSET */
+#define EMAC_ICSSG_SWITCH_PSI_L_REGULAR_FLOW_ID_BASE_OFFSET PSI_L_REGULAR_FLOW_ID_BASE_OFFSET
+
+/* Base Flow ID for sending mgmt and Tx TS to Host for Slice0 */
+#define PSI_L_MGMT_FLOW_ID_OFFSET 0x0026
+
+/* Same as PSI_L_MGMT_FLOW_ID_OFFSET */
+#define EMAC_ICSSG_SWITCH_PSI_L_MGMT_FLOW_ID_BASE_OFFSET PSI_L_MGMT_FLOW_ID_OFFSET
+
+/* Queue number for Special Packets written here */
+#define SPL_PKT_DEFAULT_PRIORITY 0x0028
+
+/* Express Preemptible Queue Mask */
+#define EXPRESS_PRE_EMPTIVE_Q_MASK 0x0029
+
+/* Port1/Port2 Default Queue number for untagged Packets, only 1B is used */
+#define QUEUE_NUM_UNTAGGED 0x002A
+
+/* Stores the table used for priority regeneration. 1B per PCP/Queue */
+#define PORT_Q_PRIORITY_REGEN_OFFSET 0x002C
+
+/* For marking Packet as priority/express (this feature is disabled) or
+ * cut-through/S&F.
+ */
+#define EXPRESS_PRE_EMPTIVE_Q_MAP 0x0034
+
+/* Stores the table used for priority mapping. 1B per PCP/Queue */
+#define PORT_Q_PRIORITY_MAPPING_OFFSET 0x003C
+
+/* Used to notify the FW of the current link speed */
+#define PORT_LINK_SPEED_OFFSET 0x00A8
+
+/* TAS gate mask for windows list0 */
+#define TAS_GATE_MASK_LIST0 0x0100
+
+/* TAS gate mask for windows list1 */
+#define TAS_GATE_MASK_LIST1 0x0350
+
+/* Memory to Enable/Disable Preemption on TX side */
+#define PRE_EMPTION_ENABLE_TX 0x05A0
+
+/* Active State of Preemption on TX side */
+#define PRE_EMPTION_ACTIVE_TX 0x05A1
+
+/* Memory to Enable/Disable Verify State Machine Preemption */
+#define PRE_EMPTION_ENABLE_VERIFY 0x05A2
+
+/* Verify Status of State Machine */
+#define PRE_EMPTION_VERIFY_STATUS 0x05A3
+
+/* Non Final Fragment Size supported by Link Partner */
+#define PRE_EMPTION_ADD_FRAG_SIZE_REMOTE 0x05A4
+
+/* Non Final Fragment Size supported by Firmware */
+#define PRE_EMPTION_ADD_FRAG_SIZE_LOCAL 0x05A6
+
+/* Time in ms the State machine waits for respond Packet */
+#define PRE_EMPTION_VERIFY_TIME 0x05A8
+
+/* Memory used for R30 related management commands */
+#define MGR_R30_CMD_OFFSET 0x05AC
+
+/* HW Buffer Pool0 base address */
+#define BUFFER_POOL_0_ADDR_OFFSET 0x05BC
+
+/* 16B for Host Egress MSMC Q (Pre-emptible) context */
+#define HOST_RX_Q_PRE_CONTEXT_OFFSET 0x0684
+
+/* Buffer for 8 FDB entries to be added by 'Add Multiple FDB entries IOCTL' */
+#define FDB_CMD_BUFFER 0x0894
+
+/* TAS queue max sdu length list */
+#define TAS_QUEUE_MAX_SDU_LIST 0x08FA
+
+/* Used by FW to generate random number with the SEED value */
+#define HD_RAND_SEED_OFFSET 0x0934
+
+/* 16B for Host Egress MSMC Q (Express) context */
+#define HOST_RX_Q_EXP_CONTEXT_OFFSET 0x0940
+
+/* Start of 32 bits PA_STAT counters */
+#define PA_STAT_32b_START_OFFSET 0x0080
+
+#endif /* __NET_TI_ICSSG_SWITCH_MAP_H */
--
2.34.1
Add icssg_stats.c to help dump, icssg related driver statistics.
ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, etc. These registers are of 32 bits and hence in case of 1G
link, they overflows in around 32 seconds. The behaviour of these registers
is such that they don't roll back to 0 after overflow but rather stay at
UINT_MAX.
These registers support a feature where the value written to them is
subtracted from the register. This feature can be utilized to fix the
overflowing of stats.
This solution uses a Workqueues based solution where a function gets
called before the registers overflow (every 25 seconds in 1G link, 25000
seconds in 100M link), this function saves the register
values in local variables and writes the last read value to the
register. So any update during the read will be taken care of.
Signed-off-by: MD Danish Anwar <[email protected]>
---
drivers/net/ethernet/ti/Makefile | 1 +
drivers/net/ethernet/ti/icssg/icssg_prueth.c | 8 +
drivers/net/ethernet/ti/icssg/icssg_prueth.h | 8 +
drivers/net/ethernet/ti/icssg/icssg_stats.c | 44 ++++++
drivers/net/ethernet/ti/icssg/icssg_stats.h | 158 +++++++++++++++++++
5 files changed, 219 insertions(+)
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_stats.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_stats.h
diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
index efb050cbb4a8..03d9b2b36b5f 100644
--- a/drivers/net/ethernet/ti/Makefile
+++ b/drivers/net/ethernet/ti/Makefile
@@ -36,3 +36,4 @@ icssg-prueth-y := k3-cppi-desc-pool.o \
icssg/icssg_queues.o \
icssg/icssg_config.o \
icssg/icssg_mii_cfg.o \
+ icssg/icssg_stats.o \
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
index 1869e38f898f..d0bb4db11b30 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
@@ -8,6 +8,7 @@
#include <linux/bitops.h>
#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/dma/ti-cppi5.h>
#include <linux/etherdevice.h>
@@ -1090,6 +1091,8 @@ static int emac_ndo_open(struct net_device *ndev)
prueth->emacs_initialized++;
+ queue_work(system_long_wq, &emac->stats_work.work);
+
return 0;
reset_tx_chan:
@@ -1164,6 +1167,9 @@ static int emac_ndo_stop(struct net_device *ndev)
cancel_work_sync(&emac->rx_mode_work);
+ /* Destroying the queued work in ndo_stop() */
+ cancel_delayed_work_sync(&emac->stats_work);
+
/* stop PRUs */
prueth_emac_stop(emac);
@@ -1313,6 +1319,8 @@ static int prueth_netdev_init(struct prueth *prueth,
}
INIT_WORK(&emac->rx_mode_work, emac_ndo_set_rx_mode_work);
+ INIT_DELAYED_WORK(&emac->stats_work, emac_stats_work_handler);
+
ret = pruss_request_mem_region(prueth->pruss,
port == PRUETH_PORT_MII0 ?
PRUSS_MEM_DRAM0 : PRUSS_MEM_DRAM1,
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
index b3a923e7a5c9..f13de0d2e90b 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.h
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
@@ -49,6 +49,9 @@
#define ICSSG_MAX_RFLOWS 8 /* per slice */
+/* Number of ICSSG related stats */
+#define ICSSG_NUM_STATS 60
+
/* Firmware status codes */
#define ICSS_HS_FW_READY 0x55555555
#define ICSS_HS_FW_DEAD 0xDEAD0000 /* lower 16 bits contain error code */
@@ -153,6 +156,9 @@ struct prueth_emac {
struct workqueue_struct *cmd_wq;
struct pruss_mem_region dram;
+
+ struct delayed_work stats_work;
+ u64 stats[ICSSG_NUM_STATS];
};
/**
@@ -246,4 +252,6 @@ u32 icssg_queue_level(struct prueth *prueth, int queue);
#define prueth_napi_to_tx_chn(pnapi) \
container_of(pnapi, struct prueth_tx_chn, napi_tx)
+void emac_stats_work_handler(struct work_struct *work);
+void emac_update_hardware_stats(struct prueth_emac *emac);
#endif /* __NET_TI_ICSSG_PRUETH_H */
diff --git a/drivers/net/ethernet/ti/icssg/icssg_stats.c b/drivers/net/ethernet/ti/icssg/icssg_stats.c
new file mode 100644
index 000000000000..25deb368a3f0
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_stats.c
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2018-2021 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include "icssg_prueth.h"
+#include "icssg_stats.h"
+#include <linux/regmap.h>
+
+static u32 stats_base[] = { 0x54c, /* Slice 0 stats start */
+ 0xb18, /* Slice 1 stats start */
+};
+
+void emac_update_hardware_stats(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ u32 base = stats_base[slice];
+ u32 val;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(icssg_all_stats); i++) {
+ regmap_read(prueth->miig_rt,
+ base + icssg_all_stats[i].offset,
+ &val);
+ regmap_write(prueth->miig_rt,
+ base + icssg_all_stats[i].offset,
+ val);
+
+ emac->stats[i] += val;
+ }
+}
+
+void emac_stats_work_handler(struct work_struct *work)
+{
+ struct prueth_emac *emac = container_of(work, struct prueth_emac,
+ stats_work.work);
+ emac_update_hardware_stats(emac);
+
+ queue_delayed_work(system_long_wq, &emac->stats_work,
+ msecs_to_jiffies((STATS_TIME_LIMIT_1G_MS * 1000) / emac->speed));
+}
diff --git a/drivers/net/ethernet/ti/icssg/icssg_stats.h b/drivers/net/ethernet/ti/icssg/icssg_stats.h
new file mode 100644
index 000000000000..999a4a91276c
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_stats.h
@@ -0,0 +1,158 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_STATS_H
+#define __NET_TI_ICSSG_STATS_H
+
+#include "icssg_prueth.h"
+
+#define STATS_TIME_LIMIT_1G_MS 25000 /* 25 seconds @ 1G */
+
+struct miig_stats_regs {
+ /* Rx */
+ u32 rx_packets;
+ u32 rx_broadcast_frames;
+ u32 rx_multicast_frames;
+ u32 rx_crc_errors;
+ u32 rx_mii_error_frames;
+ u32 rx_odd_nibble_frames;
+ u32 rx_frame_max_size;
+ u32 rx_max_size_error_frames;
+ u32 rx_frame_min_size;
+ u32 rx_min_size_error_frames;
+ u32 rx_over_errors;
+ u32 rx_class0_hits;
+ u32 rx_class1_hits;
+ u32 rx_class2_hits;
+ u32 rx_class3_hits;
+ u32 rx_class4_hits;
+ u32 rx_class5_hits;
+ u32 rx_class6_hits;
+ u32 rx_class7_hits;
+ u32 rx_class8_hits;
+ u32 rx_class9_hits;
+ u32 rx_class10_hits;
+ u32 rx_class11_hits;
+ u32 rx_class12_hits;
+ u32 rx_class13_hits;
+ u32 rx_class14_hits;
+ u32 rx_class15_hits;
+ u32 rx_smd_frags;
+ u32 rx_bucket1_size;
+ u32 rx_bucket2_size;
+ u32 rx_bucket3_size;
+ u32 rx_bucket4_size;
+ u32 rx_64B_frames;
+ u32 rx_bucket1_frames;
+ u32 rx_bucket2_frames;
+ u32 rx_bucket3_frames;
+ u32 rx_bucket4_frames;
+ u32 rx_bucket5_frames;
+ u32 rx_bytes;
+ u32 rx_tx_total_bytes;
+ /* Tx */
+ u32 tx_packets;
+ u32 tx_broadcast_frames;
+ u32 tx_multicast_frames;
+ u32 tx_odd_nibble_frames;
+ u32 tx_underflow_errors;
+ u32 tx_frame_max_size;
+ u32 tx_max_size_error_frames;
+ u32 tx_frame_min_size;
+ u32 tx_min_size_error_frames;
+ u32 tx_bucket1_size;
+ u32 tx_bucket2_size;
+ u32 tx_bucket3_size;
+ u32 tx_bucket4_size;
+ u32 tx_64B_frames;
+ u32 tx_bucket1_frames;
+ u32 tx_bucket2_frames;
+ u32 tx_bucket3_frames;
+ u32 tx_bucket4_frames;
+ u32 tx_bucket5_frames;
+ u32 tx_bytes;
+};
+
+#define ICSSG_STATS(field, stats_type) \
+{ \
+ #field, \
+ offsetof(struct miig_stats_regs, field), \
+ stats_type \
+}
+
+struct icssg_stats {
+ char name[ETH_GSTRING_LEN];
+ u32 offset;
+ bool standard_stats;
+};
+
+static const struct icssg_stats icssg_all_stats[] = {
+ /* Rx */
+ ICSSG_STATS(rx_packets, true),
+ ICSSG_STATS(rx_broadcast_frames, false),
+ ICSSG_STATS(rx_multicast_frames, true),
+ ICSSG_STATS(rx_crc_errors, true),
+ ICSSG_STATS(rx_mii_error_frames, false),
+ ICSSG_STATS(rx_odd_nibble_frames, false),
+ ICSSG_STATS(rx_frame_max_size, true),
+ ICSSG_STATS(rx_max_size_error_frames, false),
+ ICSSG_STATS(rx_frame_min_size, true),
+ ICSSG_STATS(rx_min_size_error_frames, false),
+ ICSSG_STATS(rx_over_errors, true),
+ ICSSG_STATS(rx_class0_hits, false),
+ ICSSG_STATS(rx_class1_hits, false),
+ ICSSG_STATS(rx_class2_hits, false),
+ ICSSG_STATS(rx_class3_hits, false),
+ ICSSG_STATS(rx_class4_hits, false),
+ ICSSG_STATS(rx_class5_hits, false),
+ ICSSG_STATS(rx_class6_hits, false),
+ ICSSG_STATS(rx_class7_hits, false),
+ ICSSG_STATS(rx_class8_hits, false),
+ ICSSG_STATS(rx_class9_hits, false),
+ ICSSG_STATS(rx_class10_hits, false),
+ ICSSG_STATS(rx_class11_hits, false),
+ ICSSG_STATS(rx_class12_hits, false),
+ ICSSG_STATS(rx_class13_hits, false),
+ ICSSG_STATS(rx_class14_hits, false),
+ ICSSG_STATS(rx_class15_hits, false),
+ ICSSG_STATS(rx_smd_frags, false),
+ ICSSG_STATS(rx_bucket1_size, true),
+ ICSSG_STATS(rx_bucket2_size, true),
+ ICSSG_STATS(rx_bucket3_size, true),
+ ICSSG_STATS(rx_bucket4_size, true),
+ ICSSG_STATS(rx_64B_frames, true),
+ ICSSG_STATS(rx_bucket1_frames, true),
+ ICSSG_STATS(rx_bucket2_frames, true),
+ ICSSG_STATS(rx_bucket3_frames, true),
+ ICSSG_STATS(rx_bucket4_frames, true),
+ ICSSG_STATS(rx_bucket5_frames, true),
+ ICSSG_STATS(rx_bytes, true),
+ ICSSG_STATS(rx_tx_total_bytes, false),
+ /* Tx */
+ ICSSG_STATS(tx_packets, true),
+ ICSSG_STATS(tx_broadcast_frames, false),
+ ICSSG_STATS(tx_multicast_frames, false),
+ ICSSG_STATS(tx_odd_nibble_frames, false),
+ ICSSG_STATS(tx_underflow_errors, false),
+ ICSSG_STATS(tx_frame_max_size, true),
+ ICSSG_STATS(tx_max_size_error_frames, false),
+ ICSSG_STATS(tx_frame_min_size, true),
+ ICSSG_STATS(tx_min_size_error_frames, false),
+ ICSSG_STATS(tx_bucket1_size, true),
+ ICSSG_STATS(tx_bucket2_size, true),
+ ICSSG_STATS(tx_bucket3_size, true),
+ ICSSG_STATS(tx_bucket4_size, true),
+ ICSSG_STATS(tx_64B_frames, true),
+ ICSSG_STATS(tx_bucket1_frames, true),
+ ICSSG_STATS(tx_bucket2_frames, true),
+ ICSSG_STATS(tx_bucket3_frames, true),
+ ICSSG_STATS(tx_bucket4_frames, true),
+ ICSSG_STATS(tx_bucket5_frames, true),
+ ICSSG_STATS(tx_bytes, true),
+};
+
+#endif /* __NET_TI_ICSSG_STATS_H */
--
2.34.1
Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.
Signed-off-by: MD Danish Anwar <[email protected]>
---
drivers/net/ethernet/ti/icssg/icssg_prueth.c | 22 ++++++++++++++++++++
drivers/net/ethernet/ti/icssg/icssg_prueth.h | 2 ++
drivers/net/ethernet/ti/icssg/icssg_stats.c | 13 ++++++++++++
3 files changed, 37 insertions(+)
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
index d0bb4db11b30..e641b6ce9415 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
@@ -1240,6 +1240,27 @@ static int emac_ndo_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
return phy_do_ioctl(ndev, ifr, cmd);
}
+static void emac_ndo_get_stats64(struct net_device *ndev,
+ struct rtnl_link_stats64 *stats)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ emac_update_hardware_stats(emac);
+
+ stats->rx_packets = emac_get_stat_by_name(emac, "rx_packets");
+ stats->rx_bytes = emac_get_stat_by_name(emac, "rx_bytes");
+ stats->tx_packets = emac_get_stat_by_name(emac, "tx_packets");
+ stats->tx_bytes = emac_get_stat_by_name(emac, "tx_bytes");
+ stats->rx_crc_errors = emac_get_stat_by_name(emac, "rx_crc_errors");
+ stats->rx_over_errors = emac_get_stat_by_name(emac, "rx_over_errors");
+ stats->multicast = emac_get_stat_by_name(emac, "rx_multicast_frames");
+
+ stats->rx_errors = ndev->stats.rx_errors;
+ stats->rx_dropped = ndev->stats.rx_dropped;
+ stats->tx_errors = ndev->stats.tx_errors;
+ stats->tx_dropped = ndev->stats.tx_dropped;
+}
+
static const struct net_device_ops emac_netdev_ops = {
.ndo_open = emac_ndo_open,
.ndo_stop = emac_ndo_stop,
@@ -1249,6 +1270,7 @@ static const struct net_device_ops emac_netdev_ops = {
.ndo_tx_timeout = emac_ndo_tx_timeout,
.ndo_set_rx_mode = emac_ndo_set_rx_mode,
.ndo_eth_ioctl = emac_ndo_ioctl,
+ .ndo_get_stats64 = emac_ndo_get_stats64,
};
/* get emac_port corresponding to eth_node name */
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
index f13de0d2e90b..e58cd8db7ba0 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.h
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
@@ -51,6 +51,7 @@
/* Number of ICSSG related stats */
#define ICSSG_NUM_STATS 60
+#define ICSSG_NUM_STANDARD_STATS 31
/* Firmware status codes */
#define ICSS_HS_FW_READY 0x55555555
@@ -254,4 +255,5 @@ u32 icssg_queue_level(struct prueth *prueth, int queue);
void emac_stats_work_handler(struct work_struct *work);
void emac_update_hardware_stats(struct prueth_emac *emac);
+int emac_get_stat_by_name(struct prueth_emac *emac, char *stat_name);
#endif /* __NET_TI_ICSSG_PRUETH_H */
diff --git a/drivers/net/ethernet/ti/icssg/icssg_stats.c b/drivers/net/ethernet/ti/icssg/icssg_stats.c
index 25deb368a3f0..bb0b33927e3b 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_stats.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_stats.c
@@ -42,3 +42,16 @@ void emac_stats_work_handler(struct work_struct *work)
queue_delayed_work(system_long_wq, &emac->stats_work,
msecs_to_jiffies((STATS_TIME_LIMIT_1G_MS * 1000) / emac->speed));
}
+
+int emac_get_stat_by_name(struct prueth_emac *emac, char *stat_name)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(icssg_all_stats); i++) {
+ if (!strcmp(icssg_all_stats[i].name, stat_name))
+ return emac->stats[icssg_all_stats[i].offset / sizeof(u32)];
+ }
+
+ netdev_err(emac->ndev, "Invalid stats %s\n", stat_name);
+ return -EINVAL;
+}
--
2.34.1
Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
---
drivers/net/ethernet/ti/Makefile | 1 +
drivers/net/ethernet/ti/icssg/icssg_ethtool.c | 188 ++++++++++++++++++
drivers/net/ethernet/ti/icssg/icssg_prueth.c | 1 +
drivers/net/ethernet/ti/icssg/icssg_prueth.h | 3 +
4 files changed, 193 insertions(+)
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_ethtool.c
diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
index 03d9b2b36b5f..9176d79c36e1 100644
--- a/drivers/net/ethernet/ti/Makefile
+++ b/drivers/net/ethernet/ti/Makefile
@@ -37,3 +37,4 @@ icssg-prueth-y := k3-cppi-desc-pool.o \
icssg/icssg_config.o \
icssg/icssg_mii_cfg.o \
icssg/icssg_stats.o \
+ icssg/icssg_ethtool.o
diff --git a/drivers/net/ethernet/ti/icssg/icssg_ethtool.c b/drivers/net/ethernet/ti/icssg/icssg_ethtool.c
new file mode 100644
index 000000000000..02c312f01d10
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_ethtool.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include "icssg_prueth.h"
+#include "icssg_stats.h"
+
+static void emac_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *info)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ struct prueth *prueth = emac->prueth;
+
+ strscpy(info->driver, dev_driver_string(prueth->dev),
+ sizeof(info->driver));
+ strscpy(info->bus_info, dev_name(prueth->dev), sizeof(info->bus_info));
+}
+
+static u32 emac_get_msglevel(struct net_device *ndev)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ return emac->msg_enable;
+}
+
+static void emac_set_msglevel(struct net_device *ndev, u32 value)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ emac->msg_enable = value;
+}
+
+static int emac_get_link_ksettings(struct net_device *ndev,
+ struct ethtool_link_ksettings *ecmd)
+{
+ return phy_ethtool_get_link_ksettings(ndev, ecmd);
+}
+
+static int emac_set_link_ksettings(struct net_device *ndev,
+ const struct ethtool_link_ksettings *ecmd)
+{
+ return phy_ethtool_set_link_ksettings(ndev, ecmd);
+}
+
+static int emac_get_eee(struct net_device *ndev, struct ethtool_eee *edata)
+{
+ if (!ndev->phydev)
+ return -EOPNOTSUPP;
+
+ return phy_ethtool_get_eee(ndev->phydev, edata);
+}
+
+static int emac_set_eee(struct net_device *ndev, struct ethtool_eee *edata)
+{
+ if (!ndev->phydev)
+ return -EOPNOTSUPP;
+
+ return phy_ethtool_set_eee(ndev->phydev, edata);
+}
+
+static int emac_nway_reset(struct net_device *ndev)
+{
+ return phy_ethtool_nway_reset(ndev);
+}
+
+static int emac_get_sset_count(struct net_device *ndev, int stringset)
+{
+ switch (stringset) {
+ case ETH_SS_STATS:
+ return ICSSG_NUM_ETHTOOL_STATS;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void emac_get_strings(struct net_device *ndev, u32 stringset, u8 *data)
+{
+ u8 *p = data;
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < ARRAY_SIZE(icssg_all_stats); i++) {
+ if (!icssg_all_stats[i].standard_stats) {
+ memcpy(p, icssg_all_stats[i].name,
+ ETH_GSTRING_LEN);
+ p += ETH_GSTRING_LEN;
+ }
+ }
+ break;
+ default:
+ break;
+ }
+}
+
+static void emac_get_ethtool_stats(struct net_device *ndev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ int i;
+
+ emac_update_hardware_stats(emac);
+
+ for (i = 0; i < ARRAY_SIZE(icssg_all_stats); i++)
+ if (!icssg_all_stats[i].standard_stats)
+ *(data++) = emac->stats[i];
+}
+
+static int emac_set_channels(struct net_device *ndev,
+ struct ethtool_channels *ch)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ /* Check if interface is up. Can change the num queues when
+ * the interface is down.
+ */
+ if (netif_running(emac->ndev))
+ return -EBUSY;
+
+ emac->tx_ch_num = ch->tx_count;
+
+ return 0;
+}
+
+static void emac_get_channels(struct net_device *ndev,
+ struct ethtool_channels *ch)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ ch->max_rx = 1;
+ ch->max_tx = PRUETH_MAX_TX_QUEUES;
+ ch->rx_count = 1;
+ ch->tx_count = emac->tx_ch_num;
+}
+
+static const struct ethtool_rmon_hist_range emac_rmon_ranges[] = {
+ { 0, 64},
+ { 65, 128},
+ { 129, 256},
+ { 257, 512},
+ { 513, PRUETH_MAX_PKT_SIZE},
+ {}
+};
+
+static void emac_get_rmon_stats(struct net_device *ndev,
+ struct ethtool_rmon_stats *rmon_stats,
+ const struct ethtool_rmon_hist_range **ranges)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ *ranges = emac_rmon_ranges;
+
+ rmon_stats->undersize_pkts = emac_get_stat_by_name(emac, "rx_bucket1_frames") -
+ emac_get_stat_by_name(emac, "rx_64B_frames");
+
+ rmon_stats->hist[0] = emac_get_stat_by_name(emac, "rx_bucket1_frames");
+ rmon_stats->hist[1] = emac_get_stat_by_name(emac, "rx_bucket2_frames");
+ rmon_stats->hist[2] = emac_get_stat_by_name(emac, "rx_bucket3_frames");
+ rmon_stats->hist[3] = emac_get_stat_by_name(emac, "rx_bucket4_frames");
+ rmon_stats->hist[4] = emac_get_stat_by_name(emac, "rx_bucket5_frames");
+
+ rmon_stats->hist_tx[0] = emac_get_stat_by_name(emac, "tx_bucket1_frames");
+ rmon_stats->hist_tx[1] = emac_get_stat_by_name(emac, "tx_bucket2_frames");
+ rmon_stats->hist_tx[2] = emac_get_stat_by_name(emac, "tx_bucket3_frames");
+ rmon_stats->hist_tx[3] = emac_get_stat_by_name(emac, "tx_bucket4_frames");
+ rmon_stats->hist_tx[4] = emac_get_stat_by_name(emac, "tx_bucket5_frames");
+}
+
+const struct ethtool_ops icssg_ethtool_ops = {
+ .get_drvinfo = emac_get_drvinfo,
+ .get_msglevel = emac_get_msglevel,
+ .set_msglevel = emac_set_msglevel,
+ .get_sset_count = emac_get_sset_count,
+ .get_ethtool_stats = emac_get_ethtool_stats,
+ .get_strings = emac_get_strings,
+ .get_channels = emac_get_channels,
+ .set_channels = emac_set_channels,
+ .get_link_ksettings = emac_get_link_ksettings,
+ .set_link_ksettings = emac_set_link_ksettings,
+ .get_link = ethtool_op_get_link,
+ .get_eee = emac_get_eee,
+ .set_eee = emac_set_eee,
+ .nway_reset = emac_nway_reset,
+ .get_rmon_stats = emac_get_rmon_stats,
+};
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
index e641b6ce9415..80721d82f6c5 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
@@ -1421,6 +1421,7 @@ static int prueth_netdev_init(struct prueth *prueth,
ndev->min_mtu = PRUETH_MIN_PKT_SIZE;
ndev->max_mtu = PRUETH_MAX_MTU;
ndev->netdev_ops = &emac_netdev_ops;
+ ndev->ethtool_ops = &icssg_ethtool_ops;
ndev->hw_features = NETIF_F_SG;
ndev->features = ndev->hw_features;
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
index e58cd8db7ba0..a8ce4d01ef16 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.h
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
@@ -52,6 +52,7 @@
/* Number of ICSSG related stats */
#define ICSSG_NUM_STATS 60
#define ICSSG_NUM_STANDARD_STATS 31
+#define ICSSG_NUM_ETHTOOL_STATS (ICSSG_NUM_STATS - ICSSG_NUM_STANDARD_STATS)
/* Firmware status codes */
#define ICSS_HS_FW_READY 0x55555555
@@ -230,6 +231,8 @@ static inline int prueth_emac_slice(struct prueth_emac *emac)
}
}
+extern const struct ethtool_ops icssg_ethtool_ops;
+
/* Classifier helpers */
void icssg_class_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac);
void icssg_class_set_host_mac_addr(struct regmap *miig_rt, const u8 *mac);
--
2.34.1
Add MII helper APIs and MACROs. These APIs and MACROs will be later used
by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has
definition of prueth related structures.
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
---
drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c | 120 +++++++++++
drivers/net/ethernet/ti/icssg/icssg_mii_rt.h | 151 ++++++++++++++
drivers/net/ethernet/ti/icssg/icssg_prueth.h | 197 ++++++++++++++++++
3 files changed, 468 insertions(+)
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_mii_rt.h
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_prueth.h
diff --git a/drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c b/drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c
new file mode 100644
index 000000000000..92718ae40d7e
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_mii_cfg.c
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet Driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+#include "icssg_mii_rt.h"
+#include "icssg_prueth.h"
+
+void icssg_mii_update_ipg(struct regmap *mii_rt, int mii, u32 ipg)
+{
+ u32 val;
+
+ if (mii == ICSS_MII0) {
+ regmap_write(mii_rt, PRUSS_MII_RT_TX_IPG0, ipg);
+ } else {
+ regmap_read(mii_rt, PRUSS_MII_RT_TX_IPG0, &val);
+ regmap_write(mii_rt, PRUSS_MII_RT_TX_IPG1, ipg);
+ regmap_write(mii_rt, PRUSS_MII_RT_TX_IPG0, val);
+ }
+}
+
+void icssg_mii_update_mtu(struct regmap *mii_rt, int mii, int mtu)
+{
+ mtu += (ETH_HLEN + ETH_FCS_LEN);
+ if (mii == ICSS_MII0) {
+ regmap_update_bits(mii_rt,
+ PRUSS_MII_RT_RX_FRMS0,
+ PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK,
+ (mtu - 1) << PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT);
+ } else {
+ regmap_update_bits(mii_rt,
+ PRUSS_MII_RT_RX_FRMS1,
+ PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK,
+ (mtu - 1) << PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT);
+ }
+}
+
+void icssg_update_rgmii_cfg(struct regmap *miig_rt, struct prueth_emac *emac)
+{
+ u32 gig_en_mask, gig_val = 0, full_duplex_mask, full_duplex_val = 0;
+ int slice = prueth_emac_slice(emac);
+ u32 inband_en_mask, inband_val = 0;
+
+ gig_en_mask = (slice == ICSS_MII0) ? RGMII_CFG_GIG_EN_MII0 :
+ RGMII_CFG_GIG_EN_MII1;
+ if (emac->speed == SPEED_1000)
+ gig_val = gig_en_mask;
+ regmap_update_bits(miig_rt, RGMII_CFG_OFFSET, gig_en_mask, gig_val);
+
+ inband_en_mask = (slice == ICSS_MII0) ? RGMII_CFG_INBAND_EN_MII0 :
+ RGMII_CFG_INBAND_EN_MII1;
+ if (emac->speed == SPEED_10 && phy_interface_mode_is_rgmii(emac->phy_if))
+ inband_val = inband_en_mask;
+ regmap_update_bits(miig_rt, RGMII_CFG_OFFSET, inband_en_mask, inband_val);
+
+ full_duplex_mask = (slice == ICSS_MII0) ? RGMII_CFG_FULL_DUPLEX_MII0 :
+ RGMII_CFG_FULL_DUPLEX_MII1;
+ if (emac->duplex == DUPLEX_FULL)
+ full_duplex_val = full_duplex_mask;
+ regmap_update_bits(miig_rt, RGMII_CFG_OFFSET, full_duplex_mask,
+ full_duplex_val);
+}
+
+void icssg_miig_set_interface_mode(struct regmap *miig_rt, int mii, phy_interface_t phy_if)
+{
+ u32 val, mask, shift;
+
+ mask = mii == ICSS_MII0 ? ICSSG_CFG_MII0_MODE : ICSSG_CFG_MII1_MODE;
+ shift = mii == ICSS_MII0 ? ICSSG_CFG_MII0_MODE_SHIFT : ICSSG_CFG_MII1_MODE_SHIFT;
+
+ val = MII_MODE_RGMII;
+ if (phy_if == PHY_INTERFACE_MODE_MII)
+ val = MII_MODE_MII;
+
+ val <<= shift;
+ regmap_update_bits(miig_rt, ICSSG_CFG_OFFSET, mask, val);
+ regmap_read(miig_rt, ICSSG_CFG_OFFSET, &val);
+}
+
+u32 icssg_rgmii_cfg_get_bitfield(struct regmap *miig_rt, u32 mask, u32 shift)
+{
+ u32 val;
+
+ regmap_read(miig_rt, RGMII_CFG_OFFSET, &val);
+ val &= mask;
+ val >>= shift;
+
+ return val;
+}
+
+u32 icssg_rgmii_get_speed(struct regmap *miig_rt, int mii)
+{
+ u32 shift = RGMII_CFG_SPEED_MII0_SHIFT, mask = RGMII_CFG_SPEED_MII0;
+
+ if (mii == ICSS_MII1) {
+ shift = RGMII_CFG_SPEED_MII1_SHIFT;
+ mask = RGMII_CFG_SPEED_MII1;
+ }
+
+ return icssg_rgmii_cfg_get_bitfield(miig_rt, mask, shift);
+}
+
+u32 icssg_rgmii_get_fullduplex(struct regmap *miig_rt, int mii)
+{
+ u32 shift = RGMII_CFG_FULLDUPLEX_MII0_SHIFT;
+ u32 mask = RGMII_CFG_FULLDUPLEX_MII0;
+
+ if (mii == ICSS_MII1) {
+ shift = RGMII_CFG_FULLDUPLEX_MII1_SHIFT;
+ mask = RGMII_CFG_FULLDUPLEX_MII1;
+ }
+
+ return icssg_rgmii_cfg_get_bitfield(miig_rt, mask, shift);
+}
diff --git a/drivers/net/ethernet/ti/icssg/icssg_mii_rt.h b/drivers/net/ethernet/ti/icssg/icssg_mii_rt.h
new file mode 100644
index 000000000000..55a59bf5299c
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_mii_rt.h
@@ -0,0 +1,151 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* PRU-ICSS MII_RT register definitions
+ *
+ * Copyright (C) 2015-2022 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#ifndef __NET_PRUSS_MII_RT_H__
+#define __NET_PRUSS_MII_RT_H__
+
+#include <linux/if_ether.h>
+#include <linux/phy.h>
+
+/* PRUSS_MII_RT Registers */
+#define PRUSS_MII_RT_RXCFG0 0x0
+#define PRUSS_MII_RT_RXCFG1 0x4
+#define PRUSS_MII_RT_TXCFG0 0x10
+#define PRUSS_MII_RT_TXCFG1 0x14
+#define PRUSS_MII_RT_TX_CRC0 0x20
+#define PRUSS_MII_RT_TX_CRC1 0x24
+#define PRUSS_MII_RT_TX_IPG0 0x30
+#define PRUSS_MII_RT_TX_IPG1 0x34
+#define PRUSS_MII_RT_PRS0 0x38
+#define PRUSS_MII_RT_PRS1 0x3c
+#define PRUSS_MII_RT_RX_FRMS0 0x40
+#define PRUSS_MII_RT_RX_FRMS1 0x44
+#define PRUSS_MII_RT_RX_PCNT0 0x48
+#define PRUSS_MII_RT_RX_PCNT1 0x4c
+#define PRUSS_MII_RT_RX_ERR0 0x50
+#define PRUSS_MII_RT_RX_ERR1 0x54
+
+/* PRUSS_MII_RT_RXCFG0/1 bits */
+#define PRUSS_MII_RT_RXCFG_RX_ENABLE BIT(0)
+#define PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS BIT(1)
+#define PRUSS_MII_RT_RXCFG_RX_CUT_PREAMBLE BIT(2)
+#define PRUSS_MII_RT_RXCFG_RX_MUX_SEL BIT(3)
+#define PRUSS_MII_RT_RXCFG_RX_L2_EN BIT(4)
+#define PRUSS_MII_RT_RXCFG_RX_BYTE_SWAP BIT(5)
+#define PRUSS_MII_RT_RXCFG_RX_AUTO_FWD_PRE BIT(6)
+#define PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS BIT(9)
+
+/* PRUSS_MII_RT_TXCFG0/1 bits */
+#define PRUSS_MII_RT_TXCFG_TX_ENABLE BIT(0)
+#define PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE BIT(1)
+#define PRUSS_MII_RT_TXCFG_TX_EN_MODE BIT(2)
+#define PRUSS_MII_RT_TXCFG_TX_BYTE_SWAP BIT(3)
+#define PRUSS_MII_RT_TXCFG_TX_MUX_SEL BIT(8)
+#define PRUSS_MII_RT_TXCFG_PRE_TX_AUTO_SEQUENCE BIT(9)
+#define PRUSS_MII_RT_TXCFG_PRE_TX_AUTO_ESC_ERR BIT(10)
+#define PRUSS_MII_RT_TXCFG_TX_32_MODE_EN BIT(11)
+#define PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN BIT(12) /* SR2.0 onwards */
+
+#define PRUSS_MII_RT_TXCFG_TX_START_DELAY_SHIFT 16
+#define PRUSS_MII_RT_TXCFG_TX_START_DELAY_MASK GENMASK(25, 16)
+
+#define PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_SHIFT 28
+#define PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_MASK GENMASK(30, 28)
+
+/* PRUSS_MII_RT_TX_IPG0/1 bits */
+#define PRUSS_MII_RT_TX_IPG_IPG_SHIFT 0
+#define PRUSS_MII_RT_TX_IPG_IPG_MASK GENMASK(9, 0)
+
+/* PRUSS_MII_RT_PRS0/1 bits */
+#define PRUSS_MII_RT_PRS_COL BIT(0)
+#define PRUSS_MII_RT_PRS_CRS BIT(1)
+
+/* PRUSS_MII_RT_RX_FRMS0/1 bits */
+#define PRUSS_MII_RT_RX_FRMS_MIN_FRM_SHIFT 0
+#define PRUSS_MII_RT_RX_FRMS_MIN_FRM_MASK GENMASK(15, 0)
+
+#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT 16
+#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK GENMASK(31, 16)
+
+/* Min/Max in MII_RT_RX_FRMS */
+/* For EMAC and Switch */
+#define PRUSS_MII_RT_RX_FRMS_MAX (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)
+#define PRUSS_MII_RT_RX_FRMS_MIN_FRM (64)
+
+/* for HSR and PRP */
+#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_LRE (PRUSS_MII_RT_RX_FRMS_MAX + \
+ ICSS_LRE_TAG_RCT_SIZE)
+/* PRUSS_MII_RT_RX_PCNT0/1 bits */
+#define PRUSS_MII_RT_RX_PCNT_MIN_PCNT_SHIFT 0
+#define PRUSS_MII_RT_RX_PCNT_MIN_PCNT_MASK GENMASK(3, 0)
+
+#define PRUSS_MII_RT_RX_PCNT_MAX_PCNT_SHIFT 4
+#define PRUSS_MII_RT_RX_PCNT_MAX_PCNT_MASK GENMASK(7, 4)
+
+/* PRUSS_MII_RT_RX_ERR0/1 bits */
+#define PRUSS_MII_RT_RX_ERR_MIN_PCNT_ERR BIT(0)
+#define PRUSS_MII_RT_RX_ERR_MAX_PCNT_ERR BIT(1)
+#define PRUSS_MII_RT_RX_ERR_MIN_FRM_ERR BIT(2)
+#define PRUSS_MII_RT_RX_ERR_MAX_FRM_ERR BIT(3)
+
+#define ICSSG_CFG_OFFSET 0
+#define RGMII_CFG_OFFSET 4
+
+/* Constant to choose between MII0 and MII1 */
+#define ICSS_MII0 0
+#define ICSS_MII1 1
+
+/* ICSSG_CFG Register bits */
+#define ICSSG_CFG_SGMII_MODE BIT(16)
+#define ICSSG_CFG_TX_PRU_EN BIT(11)
+#define ICSSG_CFG_RX_SFD_TX_SOF_EN BIT(10)
+#define ICSSG_CFG_RTU_PRU_PSI_SHARE_EN BIT(9)
+#define ICSSG_CFG_IEP1_TX_EN BIT(8)
+#define ICSSG_CFG_MII1_MODE GENMASK(6, 5)
+#define ICSSG_CFG_MII1_MODE_SHIFT 5
+#define ICSSG_CFG_MII0_MODE GENMASK(4, 3)
+#define ICSSG_CFG_MII0_MODE_SHIFT 3
+#define ICSSG_CFG_RX_L2_G_EN BIT(2)
+#define ICSSG_CFG_TX_L2_EN BIT(1)
+#define ICSSG_CFG_TX_L1_EN BIT(0)
+
+enum mii_mode {
+ MII_MODE_MII = 0,
+ MII_MODE_RGMII
+};
+
+/* RGMII CFG Register bits */
+#define RGMII_CFG_INBAND_EN_MII0 BIT(16)
+#define RGMII_CFG_GIG_EN_MII0 BIT(17)
+#define RGMII_CFG_INBAND_EN_MII1 BIT(20)
+#define RGMII_CFG_GIG_EN_MII1 BIT(21)
+#define RGMII_CFG_FULL_DUPLEX_MII0 BIT(18)
+#define RGMII_CFG_FULL_DUPLEX_MII1 BIT(22)
+#define RGMII_CFG_SPEED_MII0 GENMASK(2, 1)
+#define RGMII_CFG_SPEED_MII1 GENMASK(6, 5)
+#define RGMII_CFG_SPEED_MII0_SHIFT 1
+#define RGMII_CFG_SPEED_MII1_SHIFT 5
+#define RGMII_CFG_FULLDUPLEX_MII0 BIT(3)
+#define RGMII_CFG_FULLDUPLEX_MII1 BIT(7)
+#define RGMII_CFG_FULLDUPLEX_MII0_SHIFT 3
+#define RGMII_CFG_FULLDUPLEX_MII1_SHIFT 7
+#define RGMII_CFG_SPEED_10M 0
+#define RGMII_CFG_SPEED_100M 1
+#define RGMII_CFG_SPEED_1G 2
+
+struct regmap;
+struct prueth_emac;
+
+void icssg_mii_update_ipg(struct regmap *mii_rt, int mii, u32 ipg);
+void icssg_mii_update_mtu(struct regmap *mii_rt, int mii, int mtu);
+void icssg_update_rgmii_cfg(struct regmap *miig_rt, struct prueth_emac *emac);
+u32 icssg_rgmii_cfg_get_bitfield(struct regmap *miig_rt, u32 mask, u32 shift);
+u32 icssg_rgmii_get_speed(struct regmap *miig_rt, int mii);
+u32 icssg_rgmii_get_fullduplex(struct regmap *miig_rt, int mii);
+void icssg_miig_set_interface_mode(struct regmap *miig_rt, int mii, phy_interface_t phy_if);
+
+#endif /* __NET_PRUSS_MII_RT_H__ */
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
new file mode 100644
index 000000000000..8512f19a9b4d
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
@@ -0,0 +1,197 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_PRUETH_H
+#define __NET_TI_ICSSG_PRUETH_H
+
+#include <linux/etherdevice.h>
+#include <linux/genalloc.h>
+#include <linux/if_vlan.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/net_tstamp.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/remoteproc/pruss.h>
+#include <linux/pruss_driver.h>
+#include <linux/ptp_clock_kernel.h>
+#include <linux/remoteproc.h>
+
+#include <linux/dma-mapping.h>
+#include <linux/dma/ti-cppi5.h>
+#include <linux/dma/k3-udma-glue.h>
+
+#include <net/devlink.h>
+
+#include "icssg_switch_map.h"
+
+#define ICSS_SLICE0 0
+#define ICSS_SLICE1 1
+
+#define ICSSG_MAX_RFLOWS 8 /* per slice */
+
+/* In switch mode there are 3 real ports i.e. 3 mac addrs.
+ * however Linux sees only the host side port. The other 2 ports
+ * are the switch ports.
+ * In emac mode there are 2 real ports i.e. 2 mac addrs.
+ * Linux sees both the ports.
+ */
+enum prueth_port {
+ PRUETH_PORT_HOST = 0, /* host side port */
+ PRUETH_PORT_MII0, /* physical port RG/SG MII 0 */
+ PRUETH_PORT_MII1, /* physical port RG/SG MII 1 */
+ PRUETH_PORT_INVALID, /* Invalid prueth port */
+};
+
+enum prueth_mac {
+ PRUETH_MAC0 = 0,
+ PRUETH_MAC1,
+ PRUETH_NUM_MACS,
+ PRUETH_MAC_INVALID,
+};
+
+struct prueth_tx_chn {
+ struct device *dma_dev;
+ struct napi_struct napi_tx;
+ struct k3_cppi_desc_pool *desc_pool;
+ struct k3_udma_glue_tx_channel *tx_chn;
+ struct prueth_emac *emac;
+ u32 id;
+ u32 descs_num;
+ unsigned int irq;
+ char name[32];
+};
+
+struct prueth_rx_chn {
+ struct device *dev;
+ struct device *dma_dev;
+ struct k3_cppi_desc_pool *desc_pool;
+ struct k3_udma_glue_rx_channel *rx_chn;
+ u32 descs_num;
+ unsigned int irq[ICSSG_MAX_RFLOWS]; /* separate irq per flow */
+ char name[32];
+};
+
+/* There are 4 Tx DMA channels, but the highest priority is CH3 (thread 3)
+ * and lower three are lower priority channels or threads.
+ */
+#define PRUETH_MAX_TX_QUEUES 4
+
+/* data for each emac port */
+struct prueth_emac {
+ bool fw_running;
+ struct prueth *prueth;
+ struct net_device *ndev;
+ u8 mac_addr[6];
+ struct napi_struct napi_rx;
+ u32 msg_enable;
+
+ int link;
+ int speed;
+ int duplex;
+
+ const char *phy_id;
+ struct device_node *phy_node;
+ phy_interface_t phy_if;
+ enum prueth_port port_id;
+
+ /* DMA related */
+ struct prueth_tx_chn tx_chns[PRUETH_MAX_TX_QUEUES];
+ struct completion tdown_complete;
+ atomic_t tdown_cnt;
+ struct prueth_rx_chn rx_chns;
+ int rx_flow_id_base;
+ int tx_ch_num;
+
+ spinlock_t lock; /* serialize access */
+
+ unsigned long state;
+ struct completion cmd_complete;
+ /* Mutex to serialize access to firmware command interface */
+ struct mutex cmd_lock;
+ struct work_struct rx_mode_work;
+ struct workqueue_struct *cmd_wq;
+
+ struct pruss_mem_region dram;
+};
+
+/**
+ * struct prueth_pdata - PRUeth platform data
+ * @fdqring_mode: Free desc queue mode
+ * @quirk_10m_link_issue: 10M link detect errata
+ */
+struct prueth_pdata {
+ enum k3_ring_mode fdqring_mode;
+ u32 quirk_10m_link_issue:1;
+};
+
+/**
+ * struct prueth - PRUeth structure
+ * @dev: device
+ * @pruss: pruss handle
+ * @pru: rproc instances of PRUs
+ * @rtu: rproc instances of RTUs
+ * @txpru: rproc instances of TX_PRUs
+ * @shram: PRUSS shared RAM region
+ * @sram_pool: MSMC RAM pool for buffers
+ * @msmcram: MSMC RAM region
+ * @eth_node: DT node for the port
+ * @emac: private EMAC data structure
+ * @registered_netdevs: list of registered netdevs
+ * @miig_rt: regmap to mii_g_rt block
+ * @mii_rt: regmap to mii_rt block
+ * @pru_id: ID for each of the PRUs
+ * @pdev: pointer to ICSSG platform device
+ * @pdata: pointer to platform data for ICSSG driver
+ * @icssg_hwcmdseq: seq counter or HWQ messages
+ * @emacs_initialized: num of EMACs/ext ports that are up/running
+ */
+struct prueth {
+ struct device *dev;
+ struct pruss *pruss;
+ struct rproc *pru[PRUSS_NUM_PRUS];
+ struct rproc *rtu[PRUSS_NUM_PRUS];
+ struct rproc *txpru[PRUSS_NUM_PRUS];
+ struct pruss_mem_region shram;
+ struct gen_pool *sram_pool;
+ struct pruss_mem_region msmcram;
+
+ struct device_node *eth_node[PRUETH_NUM_MACS];
+ struct prueth_emac *emac[PRUETH_NUM_MACS];
+ struct net_device *registered_netdevs[PRUETH_NUM_MACS];
+ struct regmap *miig_rt;
+ struct regmap *mii_rt;
+
+ enum pruss_pru_id pru_id[PRUSS_NUM_PRUS];
+ struct platform_device *pdev;
+ struct prueth_pdata pdata;
+ u8 icssg_hwcmdseq;
+
+ int emacs_initialized;
+};
+
+/* get PRUSS SLICE number from prueth_emac */
+static inline int prueth_emac_slice(struct prueth_emac *emac)
+{
+ switch (emac->port_id) {
+ case PRUETH_PORT_MII0:
+ return ICSS_SLICE0;
+ case PRUETH_PORT_MII1:
+ return ICSS_SLICE1;
+ default:
+ return -EINVAL;
+ }
+}
+
+#endif /* __NET_TI_ICSSG_PRUETH_H */
--
2.34.1
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. These will be used by
ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: MD Danish Anwar <[email protected]>
---
.../net/ethernet/ti/icssg/icssg_classifier.c | 367 ++++++++++++++
drivers/net/ethernet/ti/icssg/icssg_config.c | 450 ++++++++++++++++++
drivers/net/ethernet/ti/icssg/icssg_config.h | 200 ++++++++
drivers/net/ethernet/ti/icssg/icssg_prueth.h | 15 +
4 files changed, 1032 insertions(+)
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_classifier.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_config.c
create mode 100644 drivers/net/ethernet/ti/icssg/icssg_config.h
diff --git a/drivers/net/ethernet/ti/icssg/icssg_classifier.c b/drivers/net/ethernet/ti/icssg/icssg_classifier.c
new file mode 100644
index 000000000000..6df53ab17fbc
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_classifier.c
@@ -0,0 +1,367 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet Driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/types.h>
+#include <linux/regmap.h>
+
+#include "icssg_prueth.h"
+
+#define ICSSG_NUM_CLASSIFIERS 16
+#define ICSSG_NUM_FT1_SLOTS 8
+#define ICSSG_NUM_FT3_SLOTS 16
+
+#define ICSSG_NUM_CLASSIFIERS_IN_USE 5
+
+/* Filter 1 - FT1 */
+#define FT1_NUM_SLOTS 8
+#define FT1_SLOT_SIZE 0x10 /* bytes */
+
+/* offsets from FT1 slot base i.e. slot 1 start */
+#define FT1_DA0 0x0
+#define FT1_DA1 0x4
+#define FT1_DA0_MASK 0x8
+#define FT1_DA1_MASK 0xc
+
+#define FT1_N_REG(slize, n, reg) \
+ (offs[slice].ft1_slot_base + FT1_SLOT_SIZE * (n) + (reg))
+
+#define FT1_LEN_MASK GENMASK(19, 16)
+#define FT1_LEN_SHIFT 16
+#define FT1_LEN(len) (((len) << FT1_LEN_SHIFT) & FT1_LEN_MASK)
+#define FT1_START_MASK GENMASK(14, 0)
+#define FT1_START(start) ((start) & FT1_START_MASK)
+#define FT1_MATCH_SLOT(n) (GENMASK(23, 16) & (BIT(n) << 16))
+
+/* FT1 config type */
+enum ft1_cfg_type {
+ FT1_CFG_TYPE_DISABLED = 0,
+ FT1_CFG_TYPE_EQ,
+ FT1_CFG_TYPE_GT,
+ FT1_CFG_TYPE_LT,
+};
+
+#define FT1_CFG_SHIFT(n) (2 * (n))
+#define FT1_CFG_MASK(n) (0x3 << FT1_CFG_SHIFT((n)))
+
+/* Filter 3 - FT3 */
+#define FT3_NUM_SLOTS 16
+#define FT3_SLOT_SIZE 0x20 /* bytes */
+
+/* offsets from FT3 slot n's base */
+#define FT3_START 0
+#define FT3_START_AUTO 0x4
+#define FT3_START_OFFSET 0x8
+#define FT3_JUMP_OFFSET 0xc
+#define FT3_LEN 0x10
+#define FT3_CFG 0x14
+#define FT3_T 0x18
+#define FT3_T_MASK 0x1c
+
+#define FT3_N_REG(slize, n, reg) \
+ (offs[slice].ft3_slot_base + FT3_SLOT_SIZE * (n) + (reg))
+
+/* offsets from rx_class n's base */
+#define RX_CLASS_AND_EN 0
+#define RX_CLASS_OR_EN 0x4
+#define RX_CLASS_NUM_SLOTS 16
+#define RX_CLASS_EN_SIZE 0x8 /* bytes */
+
+#define RX_CLASS_N_REG(slice, n, reg) \
+ (offs[slice].rx_class_base + RX_CLASS_EN_SIZE * (n) + (reg))
+
+/* RX Class Gates */
+#define RX_CLASS_GATES_SIZE 0x4 /* bytes */
+
+#define RX_CLASS_GATES_N_REG(slice, n) \
+ (offs[slice].rx_class_gates_base + RX_CLASS_GATES_SIZE * (n))
+
+#define RX_CLASS_GATES_ALLOW_MASK BIT(6)
+#define RX_CLASS_GATES_RAW_MASK BIT(5)
+#define RX_CLASS_GATES_PHASE_MASK BIT(4)
+
+/* RX Class traffic data matching bits */
+#define RX_CLASS_FT_UC BIT(31)
+#define RX_CLASS_FT_MC BIT(30)
+#define RX_CLASS_FT_BC BIT(29)
+#define RX_CLASS_FT_FW BIT(28)
+#define RX_CLASS_FT_RCV BIT(27)
+#define RX_CLASS_FT_VLAN BIT(26)
+#define RX_CLASS_FT_DA_P BIT(25)
+#define RX_CLASS_FT_DA_I BIT(24)
+#define RX_CLASS_FT_FT1_MATCH_MASK GENMASK(23, 16)
+#define RX_CLASS_FT_FT1_MATCH_SHIFT 16
+#define RX_CLASS_FT_FT3_MATCH_MASK GENMASK(15, 0)
+#define RX_CLASS_FT_FT3_MATCH_SHIFT 0
+
+#define RX_CLASS_FT_FT1_MATCH(slot) \
+ ((BIT(slot) << RX_CLASS_FT_FT1_MATCH_SHIFT) & \
+ RX_CLASS_FT_FT1_MATCH_MASK)
+
+/* RX class type */
+enum rx_class_sel_type {
+ RX_CLASS_SEL_TYPE_OR = 0,
+ RX_CLASS_SEL_TYPE_AND = 1,
+ RX_CLASS_SEL_TYPE_OR_AND_AND = 2,
+ RX_CLASS_SEL_TYPE_OR_OR_AND = 3,
+};
+
+#define FT1_CFG_SHIFT(n) (2 * (n))
+#define FT1_CFG_MASK(n) (0x3 << FT1_CFG_SHIFT((n)))
+
+#define RX_CLASS_SEL_SHIFT(n) (2 * (n))
+#define RX_CLASS_SEL_MASK(n) (0x3 << RX_CLASS_SEL_SHIFT((n)))
+
+#define ICSSG_CFG_OFFSET 0
+#define MAC_INTERFACE_0 0x18
+#define MAC_INTERFACE_1 0x1c
+
+#define ICSSG_CFG_RX_L2_G_EN BIT(2)
+
+/* These are register offsets per PRU */
+struct miig_rt_offsets {
+ u32 mac0;
+ u32 mac1;
+ u32 ft1_start_len;
+ u32 ft1_cfg;
+ u32 ft1_slot_base;
+ u32 ft3_slot_base;
+ u32 ft3_p_base;
+ u32 ft_rx_ptr;
+ u32 rx_class_base;
+ u32 rx_class_cfg1;
+ u32 rx_class_cfg2;
+ u32 rx_class_gates_base;
+ u32 rx_green;
+ u32 rx_rate_cfg_base;
+ u32 rx_rate_src_sel0;
+ u32 rx_rate_src_sel1;
+ u32 tx_rate_cfg_base;
+ u32 stat_base;
+ u32 tx_hsr_tag;
+ u32 tx_hsr_seq;
+ u32 tx_vlan_type;
+ u32 tx_vlan_ins;
+};
+
+/* These are the offset values for miig_rt_offsets registers */
+static const struct miig_rt_offsets offs[] = {
+ /* PRU0 */
+ {
+ 0x8,
+ 0xc,
+ 0x80,
+ 0x84,
+ 0x88,
+ 0x108,
+ 0x308,
+ 0x408,
+ 0x40c,
+ 0x48c,
+ 0x490,
+ 0x494,
+ 0x4d4,
+ 0x4e4,
+ 0x504,
+ 0x508,
+ 0x50c,
+ 0x54c,
+ 0x63c,
+ 0x640,
+ 0x644,
+ 0x648,
+ },
+ /* PRU1 */
+ {
+ 0x10,
+ 0x14,
+ 0x64c,
+ 0x650,
+ 0x654,
+ 0x6d4,
+ 0x8d4,
+ 0x9d4,
+ 0x9d8,
+ 0xa58,
+ 0xa5c,
+ 0xa60,
+ 0xaa0,
+ 0xab0,
+ 0xad0,
+ 0xad4,
+ 0xad8,
+ 0xb18,
+ 0xc08,
+ 0xc0c,
+ 0xc10,
+ 0xc14,
+ },
+};
+
+static void rx_class_ft1_set_start_len(struct regmap *miig_rt, int slice,
+ u16 start, u8 len)
+{
+ u32 offset, val;
+
+ offset = offs[slice].ft1_start_len;
+ val = FT1_LEN(len) | FT1_START(start);
+ regmap_write(miig_rt, offset, val);
+}
+
+static void rx_class_ft1_set_da(struct regmap *miig_rt, int slice,
+ int n, const u8 *addr)
+{
+ u32 offset;
+
+ offset = FT1_N_REG(slice, n, FT1_DA0);
+ regmap_write(miig_rt, offset, (u32)(addr[0] | addr[1] << 8 |
+ addr[2] << 16 | addr[3] << 24));
+ offset = FT1_N_REG(slice, n, FT1_DA1);
+ regmap_write(miig_rt, offset, (u32)(addr[4] | addr[5] << 8));
+}
+
+static void rx_class_ft1_set_da_mask(struct regmap *miig_rt, int slice,
+ int n, const u8 *addr)
+{
+ u32 offset;
+
+ offset = FT1_N_REG(slice, n, FT1_DA0_MASK);
+ regmap_write(miig_rt, offset, (u32)(addr[0] | addr[1] << 8 |
+ addr[2] << 16 | addr[3] << 24));
+ offset = FT1_N_REG(slice, n, FT1_DA1_MASK);
+ regmap_write(miig_rt, offset, (u32)(addr[4] | addr[5] << 8));
+}
+
+static void rx_class_ft1_cfg_set_type(struct regmap *miig_rt, int slice, int n,
+ enum ft1_cfg_type type)
+{
+ u32 offset;
+
+ offset = offs[slice].ft1_cfg;
+ regmap_update_bits(miig_rt, offset, FT1_CFG_MASK(n),
+ type << FT1_CFG_SHIFT(n));
+}
+
+static void rx_class_sel_set_type(struct regmap *miig_rt, int slice, int n,
+ enum rx_class_sel_type type)
+{
+ u32 offset;
+
+ offset = offs[slice].rx_class_cfg1;
+ regmap_update_bits(miig_rt, offset, RX_CLASS_SEL_MASK(n),
+ type << RX_CLASS_SEL_SHIFT(n));
+}
+
+static void rx_class_set_and(struct regmap *miig_rt, int slice, int n,
+ u32 data)
+{
+ u32 offset;
+
+ offset = RX_CLASS_N_REG(slice, n, RX_CLASS_AND_EN);
+ regmap_write(miig_rt, offset, data);
+}
+
+static void rx_class_set_or(struct regmap *miig_rt, int slice, int n,
+ u32 data)
+{
+ u32 offset;
+
+ offset = RX_CLASS_N_REG(slice, n, RX_CLASS_OR_EN);
+ regmap_write(miig_rt, offset, data);
+}
+
+void icssg_class_set_host_mac_addr(struct regmap *miig_rt, const u8 *mac)
+{
+ regmap_write(miig_rt, MAC_INTERFACE_0, (u32)(mac[0] | mac[1] << 8 |
+ mac[2] << 16 | mac[3] << 24));
+ regmap_write(miig_rt, MAC_INTERFACE_1, (u32)(mac[4] | mac[5] << 8));
+}
+
+void icssg_class_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac)
+{
+ regmap_write(miig_rt, offs[slice].mac0, (u32)(mac[0] | mac[1] << 8 |
+ mac[2] << 16 | mac[3] << 24));
+ regmap_write(miig_rt, offs[slice].mac1, (u32)(mac[4] | mac[5] << 8));
+}
+
+/* disable all RX traffic */
+void icssg_class_disable(struct regmap *miig_rt, int slice)
+{
+ u32 data, offset;
+ int n;
+
+ /* Enable RX_L2_G */
+ regmap_update_bits(miig_rt, ICSSG_CFG_OFFSET, ICSSG_CFG_RX_L2_G_EN,
+ ICSSG_CFG_RX_L2_G_EN);
+
+ for (n = 0; n < ICSSG_NUM_CLASSIFIERS; n++) {
+ /* AND_EN = 0 */
+ rx_class_set_and(miig_rt, slice, n, 0);
+ /* OR_EN = 0 */
+ rx_class_set_or(miig_rt, slice, n, 0);
+
+ /* set CFG1 to OR */
+ rx_class_sel_set_type(miig_rt, slice, n, RX_CLASS_SEL_TYPE_OR);
+
+ /* configure gate */
+ offset = RX_CLASS_GATES_N_REG(slice, n);
+ regmap_read(miig_rt, offset, &data);
+ /* clear class_raw so we go through filters */
+ data &= ~RX_CLASS_GATES_RAW_MASK;
+ /* set allow and phase mask */
+ data |= RX_CLASS_GATES_ALLOW_MASK | RX_CLASS_GATES_PHASE_MASK;
+ regmap_write(miig_rt, offset, data);
+ }
+
+ /* FT1 Disabled */
+ for (n = 0; n < ICSSG_NUM_FT1_SLOTS; n++) {
+ const u8 addr[] = { 0, 0, 0, 0, 0, 0, };
+
+ rx_class_ft1_cfg_set_type(miig_rt, slice, n,
+ FT1_CFG_TYPE_DISABLED);
+ rx_class_ft1_set_da(miig_rt, slice, n, addr);
+ rx_class_ft1_set_da_mask(miig_rt, slice, n, addr);
+ }
+
+ /* clear CFG2 */
+ regmap_write(miig_rt, offs[slice].rx_class_cfg2, 0);
+}
+
+void icssg_class_default(struct regmap *miig_rt, int slice, bool allmulti)
+{
+ u32 data;
+
+ /* defaults */
+ icssg_class_disable(miig_rt, slice);
+
+ /* Setup Classifier */
+ /* match on Broadcast or MAC_PRU address */
+ data = RX_CLASS_FT_BC | RX_CLASS_FT_DA_P;
+
+ /* multicast */
+ if (allmulti)
+ data |= RX_CLASS_FT_MC;
+
+ rx_class_set_or(miig_rt, slice, 0, data);
+
+ /* set CFG1 for OR_OR_AND for classifier */
+ rx_class_sel_set_type(miig_rt, slice, 0, RX_CLASS_SEL_TYPE_OR_OR_AND);
+
+ /* clear CFG2 */
+ regmap_write(miig_rt, offs[slice].rx_class_cfg2, 0);
+}
+
+/* required for SAV check */
+void icssg_ft1_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac_addr)
+{
+ const u8 mask_addr[] = { 0, 0, 0, 0, 0, 0, };
+
+ rx_class_ft1_set_start_len(miig_rt, slice, 0, 6);
+ rx_class_ft1_set_da(miig_rt, slice, 0, mac_addr);
+ rx_class_ft1_set_da_mask(miig_rt, slice, 0, mask_addr);
+ rx_class_ft1_cfg_set_type(miig_rt, slice, 0, FT1_CFG_TYPE_EQ);
+}
diff --git a/drivers/net/ethernet/ti/icssg/icssg_config.c b/drivers/net/ethernet/ti/icssg/icssg_config.c
new file mode 100644
index 000000000000..ab648d3efe85
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_config.c
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: GPL-2.0
+/* ICSSG Ethernet driver
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#include <linux/iopoll.h>
+#include <linux/regmap.h>
+#include <uapi/linux/if_ether.h>
+#include "icssg_config.h"
+#include "icssg_prueth.h"
+#include "icssg_switch_map.h"
+#include "icssg_mii_rt.h"
+
+/* TX IPG Values to be set for 100M link speed. These values are
+ * in ocp_clk cycles. So need change if ocp_clk is changed for a specific
+ * h/w design.
+ */
+
+/* IPG is in core_clk cycles */
+#define MII_RT_TX_IPG_100M 0x17
+#define MII_RT_TX_IPG_1G 0xb
+
+#define ICSSG_QUEUES_MAX 64
+#define ICSSG_QUEUE_OFFSET 0xd00
+#define ICSSG_QUEUE_PEEK_OFFSET 0xe00
+#define ICSSG_QUEUE_CNT_OFFSET 0xe40
+#define ICSSG_QUEUE_RESET_OFFSET 0xf40
+
+#define ICSSG_NUM_TX_QUEUES 8
+
+#define RECYCLE_Q_SLICE0 16
+#define RECYCLE_Q_SLICE1 17
+
+#define ICSSG_NUM_OTHER_QUEUES 5 /* port, host and special queues */
+
+#define PORT_HI_Q_SLICE0 32
+#define PORT_LO_Q_SLICE0 33
+#define HOST_HI_Q_SLICE0 34
+#define HOST_LO_Q_SLICE0 35
+#define HOST_SPL_Q_SLICE0 40 /* Special Queue */
+
+#define PORT_HI_Q_SLICE1 36
+#define PORT_LO_Q_SLICE1 37
+#define HOST_HI_Q_SLICE1 38
+#define HOST_LO_Q_SLICE1 39
+#define HOST_SPL_Q_SLICE1 41 /* Special Queue */
+
+#define MII_RXCFG_DEFAULT (PRUSS_MII_RT_RXCFG_RX_ENABLE | \
+ PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS | \
+ PRUSS_MII_RT_RXCFG_RX_L2_EN | \
+ PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS)
+
+#define MII_TXCFG_DEFAULT (PRUSS_MII_RT_TXCFG_TX_ENABLE | \
+ PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE | \
+ PRUSS_MII_RT_TXCFG_TX_32_MODE_EN | \
+ PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN)
+
+#define ICSSG_CFG_DEFAULT (ICSSG_CFG_TX_L1_EN | \
+ ICSSG_CFG_TX_L2_EN | ICSSG_CFG_RX_L2_G_EN | \
+ ICSSG_CFG_TX_PRU_EN | \
+ ICSSG_CFG_SGMII_MODE)
+
+#define FDB_GEN_CFG1 0x60
+#define SMEM_VLAN_OFFSET 8
+#define SMEM_VLAN_OFFSET_MASK GENMASK(25, 8)
+
+#define FDB_GEN_CFG2 0x64
+#define FDB_VLAN_EN BIT(6)
+#define FDB_HOST_EN BIT(2)
+#define FDB_PRU1_EN BIT(1)
+#define FDB_PRU0_EN BIT(0)
+#define FDB_EN_ALL (FDB_PRU0_EN | FDB_PRU1_EN | \
+ FDB_HOST_EN | FDB_VLAN_EN)
+
+/**
+ * struct map - ICSSG Queue Map
+ * @queue: Queue number
+ * @pd_addr_start: Packet descriptor queue reserved memory
+ * @flags: Flags
+ * @special: Indicates whether this queue is a special queue or not
+ */
+struct map {
+ int queue;
+ u32 pd_addr_start;
+ u32 flags;
+ bool special;
+};
+
+/* Hardware queue map for ICSSG */
+static const struct map hwq_map[2][ICSSG_NUM_OTHER_QUEUES] = {
+ {
+ { PORT_HI_Q_SLICE0, PORT_DESC0_HI, 0x200000, 0 },
+ { PORT_LO_Q_SLICE0, PORT_DESC0_LO, 0, 0 },
+ { HOST_HI_Q_SLICE0, HOST_DESC0_HI, 0x200000, 0 },
+ { HOST_LO_Q_SLICE0, HOST_DESC0_LO, 0, 0 },
+ { HOST_SPL_Q_SLICE0, HOST_SPPD0, 0x400000, 1 },
+ },
+ {
+ { PORT_HI_Q_SLICE1, PORT_DESC1_HI, 0xa00000, 0 },
+ { PORT_LO_Q_SLICE1, PORT_DESC1_LO, 0x800000, 0 },
+ { HOST_HI_Q_SLICE1, HOST_DESC1_HI, 0xa00000, 0 },
+ { HOST_LO_Q_SLICE1, HOST_DESC1_LO, 0x800000, 0 },
+ { HOST_SPL_Q_SLICE1, HOST_SPPD1, 0xc00000, 1 },
+ },
+};
+
+static void icssg_config_mii_init(struct prueth_emac *emac)
+{
+ u32 rxcfg, txcfg, rxcfg_reg, txcfg_reg, pcnt_reg;
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ struct regmap *mii_rt;
+
+ mii_rt = prueth->mii_rt;
+
+ rxcfg_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_RXCFG0 :
+ PRUSS_MII_RT_RXCFG1;
+ txcfg_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_TXCFG0 :
+ PRUSS_MII_RT_TXCFG1;
+ pcnt_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_RX_PCNT0 :
+ PRUSS_MII_RT_RX_PCNT1;
+
+ rxcfg = MII_RXCFG_DEFAULT;
+ txcfg = MII_TXCFG_DEFAULT;
+
+ if (slice == ICSS_MII1)
+ rxcfg |= PRUSS_MII_RT_RXCFG_RX_MUX_SEL;
+
+ /* In MII mode TX lines swapped inside ICSSG, so TX_MUX_SEL cfg need
+ * to be swapped also comparing to RGMII mode.
+ */
+ if (emac->phy_if == PHY_INTERFACE_MODE_MII && slice == ICSS_MII0)
+ txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
+ else if (emac->phy_if != PHY_INTERFACE_MODE_MII && slice == ICSS_MII1)
+ txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
+
+ regmap_write(mii_rt, rxcfg_reg, rxcfg);
+ regmap_write(mii_rt, txcfg_reg, txcfg);
+ regmap_write(mii_rt, pcnt_reg, 0x1);
+}
+
+static void icssg_miig_queues_init(struct prueth *prueth, int slice)
+{
+ struct regmap *miig_rt = prueth->miig_rt;
+ void __iomem *smem = prueth->shram.va;
+ u8 pd[ICSSG_SPECIAL_PD_SIZE];
+ int queue = 0, i, j;
+ u32 *pdword;
+
+ /* reset hwqueues */
+ if (slice)
+ queue = ICSSG_NUM_TX_QUEUES;
+
+ for (i = 0; i < ICSSG_NUM_TX_QUEUES; i++) {
+ regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET, queue);
+ queue++;
+ }
+
+ queue = slice ? RECYCLE_Q_SLICE1 : RECYCLE_Q_SLICE0;
+ regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET, queue);
+
+ for (i = 0; i < ICSSG_NUM_OTHER_QUEUES; i++) {
+ regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET,
+ hwq_map[slice][i].queue);
+ }
+
+ /* initialize packet descriptors in SMEM */
+ /* push pakcet descriptors to hwqueues */
+
+ pdword = (u32 *)pd;
+ for (j = 0; j < ICSSG_NUM_OTHER_QUEUES; j++) {
+ const struct map *mp;
+ int pd_size, num_pds;
+ u32 pdaddr;
+
+ mp = &hwq_map[slice][j];
+ if (mp->special) {
+ pd_size = ICSSG_SPECIAL_PD_SIZE;
+ num_pds = ICSSG_NUM_SPECIAL_PDS;
+ } else {
+ pd_size = ICSSG_NORMAL_PD_SIZE;
+ num_pds = ICSSG_NUM_NORMAL_PDS;
+ }
+
+ for (i = 0; i < num_pds; i++) {
+ memset(pd, 0, pd_size);
+
+ pdword[0] &= ICSSG_FLAG_MASK;
+ pdword[0] |= mp->flags;
+ pdaddr = mp->pd_addr_start + i * pd_size;
+
+ memcpy_toio(smem + pdaddr, pd, pd_size);
+ queue = mp->queue;
+ regmap_write(miig_rt, ICSSG_QUEUE_OFFSET + 4 * queue,
+ pdaddr);
+ }
+ }
+}
+
+void icssg_config_ipg(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+
+ switch (emac->speed) {
+ case SPEED_1000:
+ icssg_mii_update_ipg(prueth->mii_rt, slice, MII_RT_TX_IPG_1G);
+ break;
+ case SPEED_100:
+ icssg_mii_update_ipg(prueth->mii_rt, slice, MII_RT_TX_IPG_100M);
+ break;
+ default:
+ /* Other links speeds not supported */
+ netdev_err(emac->ndev, "Unsupported link speed\n");
+ return;
+ }
+}
+
+static void emac_r30_cmd_init(struct prueth_emac *emac)
+{
+ struct icssg_r30_cmd __iomem *p;
+ int i;
+
+ p = emac->dram.va + MGR_R30_CMD_OFFSET;
+
+ for (i = 0; i < 4; i++)
+ writel(EMAC_NONE, &p->cmd[i]);
+}
+
+static int emac_r30_is_done(struct prueth_emac *emac)
+{
+ const struct icssg_r30_cmd __iomem *p;
+ u32 cmd;
+ int i;
+
+ p = emac->dram.va + MGR_R30_CMD_OFFSET;
+
+ for (i = 0; i < 4; i++) {
+ cmd = readl(&p->cmd[i]);
+ if (cmd != EMAC_NONE)
+ return 0;
+ }
+
+ return 1;
+}
+
+static int prueth_emac_buffer_setup(struct prueth_emac *emac)
+{
+ struct icssg_buffer_pool_cfg __iomem *bpool_cfg;
+ struct icssg_rxq_ctx __iomem *rxq_ctx;
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ u32 addr;
+ int i;
+
+ /* Layout to have 64KB aligned buffer pool
+ * |BPOOL0|BPOOL1|RX_CTX0|RX_CTX1|
+ */
+
+ addr = lower_32_bits(prueth->msmcram.pa);
+ if (slice)
+ addr += PRUETH_NUM_BUF_POOLS * PRUETH_EMAC_BUF_POOL_SIZE;
+
+ if (addr % SZ_64K) {
+ dev_warn(prueth->dev, "buffer pool needs to be 64KB aligned\n");
+ return -EINVAL;
+ }
+
+ bpool_cfg = emac->dram.va + BUFFER_POOL_0_ADDR_OFFSET;
+ /* workaround for f/w bug. bpool 0 needs to be initilalized */
+ writel(addr, &bpool_cfg[0].addr);
+ writel(0, &bpool_cfg[0].len);
+
+ for (i = PRUETH_EMAC_BUF_POOL_START;
+ i < PRUETH_EMAC_BUF_POOL_START + PRUETH_NUM_BUF_POOLS;
+ i++) {
+ writel(addr, &bpool_cfg[i].addr);
+ writel(PRUETH_EMAC_BUF_POOL_SIZE, &bpool_cfg[i].len);
+ addr += PRUETH_EMAC_BUF_POOL_SIZE;
+ }
+
+ if (!slice)
+ addr += PRUETH_NUM_BUF_POOLS * PRUETH_EMAC_BUF_POOL_SIZE;
+ else
+ addr += PRUETH_EMAC_RX_CTX_BUF_SIZE * 2;
+
+ /* Pre-emptible RX buffer queue */
+ rxq_ctx = emac->dram.va + HOST_RX_Q_PRE_CONTEXT_OFFSET;
+ for (i = 0; i < 3; i++)
+ writel(addr, &rxq_ctx->start[i]);
+
+ addr += PRUETH_EMAC_RX_CTX_BUF_SIZE;
+ writel(addr, &rxq_ctx->end);
+
+ /* Express RX buffer queue */
+ rxq_ctx = emac->dram.va + HOST_RX_Q_EXP_CONTEXT_OFFSET;
+ for (i = 0; i < 3; i++)
+ writel(addr, &rxq_ctx->start[i]);
+
+ addr += PRUETH_EMAC_RX_CTX_BUF_SIZE;
+ writel(addr, &rxq_ctx->end);
+
+ return 0;
+}
+
+static void icssg_init_emac_mode(struct prueth *prueth)
+{
+ /* When the device is configured as a bridge and it is being brought
+ * back to the emac mode, the host mac address has to be set as 0.
+ */
+ u8 mac[ETH_ALEN] = { 0 };
+
+ if (prueth->emacs_initialized)
+ return;
+
+ regmap_update_bits(prueth->miig_rt, FDB_GEN_CFG1,
+ SMEM_VLAN_OFFSET_MASK, 0);
+ regmap_write(prueth->miig_rt, FDB_GEN_CFG2, 0);
+ /* Clear host MAC address */
+ icssg_class_set_host_mac_addr(prueth->miig_rt, mac);
+}
+
+int icssg_config(struct prueth *prueth, struct prueth_emac *emac, int slice)
+{
+ void __iomem *config = emac->dram.va + ICSSG_CONFIG_OFFSET;
+ struct icssg_flow_cfg __iomem *flow_cfg;
+ int ret;
+
+ icssg_init_emac_mode(prueth);
+
+ memset_io(config, 0, TAS_GATE_MASK_LIST0);
+ icssg_miig_queues_init(prueth, slice);
+
+ emac->speed = SPEED_1000;
+ emac->duplex = DUPLEX_FULL;
+ if (!phy_interface_mode_is_rgmii(emac->phy_if)) {
+ emac->speed = SPEED_100;
+ emac->duplex = DUPLEX_FULL;
+ }
+ regmap_update_bits(prueth->miig_rt, ICSSG_CFG_OFFSET,
+ ICSSG_CFG_DEFAULT, ICSSG_CFG_DEFAULT);
+ icssg_miig_set_interface_mode(prueth->miig_rt, slice, emac->phy_if);
+ icssg_config_mii_init(emac);
+ icssg_config_ipg(emac);
+ icssg_update_rgmii_cfg(prueth->miig_rt, emac);
+
+ /* set GPI mode */
+ pruss_cfg_gpimode(prueth->pruss, prueth->pru_id[slice],
+ PRUSS_GPI_MODE_MII);
+
+ /* enable XFR shift for PRU and RTU */
+ pruss_cfg_xfr_enable(prueth->pruss, PRU_TYPE_PRU, true);
+ pruss_cfg_xfr_enable(prueth->pruss, PRU_TYPE_RTU, true);
+
+ /* set C28 to 0x100 */
+ pru_rproc_set_ctable(prueth->pru[slice], PRU_C28, 0x100 << 8);
+ pru_rproc_set_ctable(prueth->rtu[slice], PRU_C28, 0x100 << 8);
+ pru_rproc_set_ctable(prueth->txpru[slice], PRU_C28, 0x100 << 8);
+
+ flow_cfg = config + PSI_L_REGULAR_FLOW_ID_BASE_OFFSET;
+ writew(emac->rx_flow_id_base, &flow_cfg->rx_base_flow);
+ writew(0, &flow_cfg->mgm_base_flow);
+ writeb(0, config + SPL_PKT_DEFAULT_PRIORITY);
+ writeb(0, config + QUEUE_NUM_UNTAGGED);
+
+ ret = prueth_emac_buffer_setup(emac);
+ if (ret)
+ return ret;
+
+ emac_r30_cmd_init(emac);
+
+ return 0;
+}
+
+/* Bitmask for ICSSG r30 commands */
+static const struct icssg_r30_cmd emac_r32_bitmask[] = {
+ {{0xffff0004, 0xffff0100, 0xffff0100, EMAC_NONE}}, /* EMAC_PORT_DISABLE */
+ {{0xfffb0040, 0xfeff0200, 0xfeff0200, EMAC_NONE}}, /* EMAC_PORT_BLOCK */
+ {{0xffbb0000, 0xfcff0000, 0xdcff0000, EMAC_NONE}}, /* EMAC_PORT_FORWARD */
+ {{0xffbb0000, 0xfcff0000, 0xfcff2000, EMAC_NONE}}, /* EMAC_PORT_FORWARD_WO_LEARNING */
+ {{0xffff0001, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT ALL */
+ {{0xfffe0002, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT TAGGED */
+ {{0xfffc0000, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT UNTAGGED and PRIO */
+ {{EMAC_NONE, 0xffff0020, EMAC_NONE, EMAC_NONE}}, /* TAS Trigger List change */
+ {{EMAC_NONE, 0xdfff1000, EMAC_NONE, EMAC_NONE}}, /* TAS set state ENABLE*/
+ {{EMAC_NONE, 0xefff2000, EMAC_NONE, EMAC_NONE}}, /* TAS set state RESET*/
+ {{EMAC_NONE, 0xcfff0000, EMAC_NONE, EMAC_NONE}}, /* TAS set state DISABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xffff0400, EMAC_NONE}}, /* UC flooding ENABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xfbff0000, EMAC_NONE}}, /* UC flooding DISABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xffff0800, EMAC_NONE}}, /* MC flooding ENABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xf7ff0000, EMAC_NONE}}, /* MC flooding DISABLE*/
+ {{EMAC_NONE, 0xffff4000, EMAC_NONE, EMAC_NONE}}, /* Preemption on Tx ENABLE*/
+ {{EMAC_NONE, 0xbfff0000, EMAC_NONE, EMAC_NONE}}, /* Preemption on Tx DISABLE*/
+ {{0xffff0010, EMAC_NONE, 0xffff0010, EMAC_NONE}}, /* VLAN AWARE*/
+ {{0xffef0000, EMAC_NONE, 0xffef0000, EMAC_NONE}} /* VLAN UNWARE*/
+};
+
+int emac_set_port_state(struct prueth_emac *emac,
+ enum icssg_port_state_cmd cmd)
+{
+ struct icssg_r30_cmd __iomem *p;
+ int ret = -ETIMEDOUT;
+ int done = 0;
+ int i;
+
+ p = emac->dram.va + MGR_R30_CMD_OFFSET;
+
+ if (cmd >= ICSSG_EMAC_PORT_MAX_COMMANDS) {
+ netdev_err(emac->ndev, "invalid port command\n");
+ return -EINVAL;
+ }
+
+ /* only one command at a time allowed to firmware */
+ mutex_lock(&emac->cmd_lock);
+
+ for (i = 0; i < 4; i++)
+ writel(emac_r32_bitmask[cmd].cmd[i], &p->cmd[i]);
+
+ /* wait for done */
+ ret = read_poll_timeout(emac_r30_is_done, done, done == 1,
+ 1000, 10000, false, emac);
+
+ if (ret == -ETIMEDOUT)
+ netdev_err(emac->ndev, "timeout waiting for command done\n");
+
+ mutex_unlock(&emac->cmd_lock);
+
+ return ret;
+}
+
+void icssg_config_set_speed(struct prueth_emac *emac)
+{
+ u8 fw_speed;
+
+ switch (emac->speed) {
+ case SPEED_1000:
+ fw_speed = FW_LINK_SPEED_1G;
+ break;
+ case SPEED_100:
+ fw_speed = FW_LINK_SPEED_100M;
+ break;
+ default:
+ /* Other links speeds not supported */
+ netdev_err(emac->ndev, "Unsupported link speed\n");
+ return;
+ }
+
+ writeb(fw_speed, emac->dram.va + PORT_LINK_SPEED_OFFSET);
+}
diff --git a/drivers/net/ethernet/ti/icssg/icssg_config.h b/drivers/net/ethernet/ti/icssg/icssg_config.h
new file mode 100644
index 000000000000..43eb0922172a
--- /dev/null
+++ b/drivers/net/ethernet/ti/icssg/icssg_config.h
@@ -0,0 +1,200 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_CONFIG_H
+#define __NET_TI_ICSSG_CONFIG_H
+
+struct icssg_buffer_pool_cfg {
+ __le32 addr;
+ __le32 len;
+} __packed;
+
+struct icssg_flow_cfg {
+ __le16 rx_base_flow;
+ __le16 mgm_base_flow;
+} __packed;
+
+#define PRUETH_PKT_TYPE_CMD 0x10
+#define PRUETH_NAV_PS_DATA_SIZE 16 /* Protocol specific data size */
+#define PRUETH_NAV_SW_DATA_SIZE 16 /* SW related data size */
+#define PRUETH_MAX_TX_DESC 512
+#define PRUETH_MAX_RX_DESC 512
+#define PRUETH_MAX_RX_FLOWS 1 /* excluding default flow */
+#define PRUETH_RX_FLOW_DATA 0
+
+#define PRUETH_EMAC_BUF_POOL_SIZE SZ_8K
+#define PRUETH_EMAC_POOLS_PER_SLICE 24
+#define PRUETH_EMAC_BUF_POOL_START 8
+#define PRUETH_NUM_BUF_POOLS 8
+#define PRUETH_EMAC_RX_CTX_BUF_SIZE SZ_16K /* per slice */
+#define MSMC_RAM_SIZE \
+ (2 * (PRUETH_EMAC_BUF_POOL_SIZE * PRUETH_NUM_BUF_POOLS + \
+ PRUETH_EMAC_RX_CTX_BUF_SIZE * 2))
+
+struct icssg_rxq_ctx {
+ __le32 start[3];
+ __le32 end;
+} __packed;
+
+/* Load time Fiwmware Configuration */
+
+#define ICSSG_FW_MGMT_CMD_HEADER 0x81
+#define ICSSG_FW_MGMT_FDB_CMD_TYPE 0x03
+#define ICSSG_FW_MGMT_CMD_TYPE 0x04
+#define ICSSG_FW_MGMT_PKT 0x80000000
+
+struct icssg_r30_cmd {
+ u32 cmd[4];
+} __packed;
+
+enum icssg_port_state_cmd {
+ ICSSG_EMAC_PORT_DISABLE = 0,
+ ICSSG_EMAC_PORT_BLOCK,
+ ICSSG_EMAC_PORT_FORWARD,
+ ICSSG_EMAC_PORT_FORWARD_WO_LEARNING,
+ ICSSG_EMAC_PORT_ACCEPT_ALL,
+ ICSSG_EMAC_PORT_ACCEPT_TAGGED,
+ ICSSG_EMAC_PORT_ACCEPT_UNTAGGED_N_PRIO,
+ ICSSG_EMAC_PORT_TAS_TRIGGER,
+ ICSSG_EMAC_PORT_TAS_ENABLE,
+ ICSSG_EMAC_PORT_TAS_RESET,
+ ICSSG_EMAC_PORT_TAS_DISABLE,
+ ICSSG_EMAC_PORT_UC_FLOODING_ENABLE,
+ ICSSG_EMAC_PORT_UC_FLOODING_DISABLE,
+ ICSSG_EMAC_PORT_MC_FLOODING_ENABLE,
+ ICSSG_EMAC_PORT_MC_FLOODING_DISABLE,
+ ICSSG_EMAC_PORT_PREMPT_TX_ENABLE,
+ ICSSG_EMAC_PORT_PREMPT_TX_DISABLE,
+ ICSSG_EMAC_PORT_VLAN_AWARE_ENABLE,
+ ICSSG_EMAC_PORT_VLAN_AWARE_DISABLE,
+ ICSSG_EMAC_PORT_MAX_COMMANDS
+};
+
+#define EMAC_NONE 0xffff0000
+#define EMAC_PRU0_P_DI 0xffff0004
+#define EMAC_PRU1_P_DI 0xffff0040
+#define EMAC_TX_P_DI 0xffff0100
+
+#define EMAC_PRU0_P_EN 0xfffb0000
+#define EMAC_PRU1_P_EN 0xffbf0000
+#define EMAC_TX_P_EN 0xfeff0000
+
+#define EMAC_P_BLOCK 0xffff0040
+#define EMAC_TX_P_BLOCK 0xffff0200
+#define EMAC_P_UNBLOCK 0xffbf0000
+#define EMAC_TX_P_UNBLOCK 0xfdff0000
+#define EMAC_LEAN_EN 0xfff70000
+#define EMAC_LEAN_DI 0xffff0008
+
+#define EMAC_ACCEPT_ALL 0xffff0001
+#define EMAC_ACCEPT_TAG 0xfffe0002
+#define EMAC_ACCEPT_PRIOR 0xfffc0000
+
+/* Config area lies in DRAM */
+#define ICSSG_CONFIG_OFFSET 0x0
+
+/* Config area lies in shared RAM */
+#define ICSSG_CONFIG_OFFSET_SLICE0 0
+#define ICSSG_CONFIG_OFFSET_SLICE1 0x8000
+
+#define ICSSG_NUM_NORMAL_PDS 64
+#define ICSSG_NUM_SPECIAL_PDS 16
+
+#define ICSSG_NORMAL_PD_SIZE 8
+#define ICSSG_SPECIAL_PD_SIZE 20
+
+#define ICSSG_FLAG_MASK 0xff00ffff
+
+struct icssg_setclock_desc {
+ u8 request;
+ u8 restore;
+ u8 acknowledgment;
+ u8 cmp_status;
+ u32 margin;
+ u32 cyclecounter0_set;
+ u32 cyclecounter1_set;
+ u32 iepcount_set;
+ u32 rsvd1;
+ u32 rsvd2;
+ u32 CMP0_current;
+ u32 iepcount_current;
+ u32 difference;
+ u32 cyclecounter0_new;
+ u32 cyclecounter1_new;
+ u32 CMP0_new;
+} __packed;
+
+#define ICSSG_CMD_POP_SLICE0 56
+#define ICSSG_CMD_POP_SLICE1 60
+
+#define ICSSG_CMD_PUSH_SLICE0 57
+#define ICSSG_CMD_PUSH_SLICE1 61
+
+#define ICSSG_RSP_POP_SLICE0 58
+#define ICSSG_RSP_POP_SLICE1 62
+
+#define ICSSG_RSP_PUSH_SLICE0 56
+#define ICSSG_RSP_PUSH_SLICE1 60
+
+#define ICSSG_TS_POP_SLICE0 59
+#define ICSSG_TS_POP_SLICE1 63
+
+#define ICSSG_TS_PUSH_SLICE0 40
+#define ICSSG_TS_PUSH_SLICE1 41
+
+/* FDB FID_C2 flag definitions */
+/* Indicates host port membership.*/
+#define ICSSG_FDB_ENTRY_P0_MEMBERSHIP BIT(0)
+/* Indicates that MAC ID is connected to physical port 1 */
+#define ICSSG_FDB_ENTRY_P1_MEMBERSHIP BIT(1)
+/* Indicates that MAC ID is connected to physical port 2 */
+#define ICSSG_FDB_ENTRY_P2_MEMBERSHIP BIT(2)
+/* Ageable bit is set for learned entries and cleared for static entries */
+#define ICSSG_FDB_ENTRY_AGEABLE BIT(3)
+/* If set for DA then packet is determined to be a special packet */
+#define ICSSG_FDB_ENTRY_BLOCK BIT(4)
+/* If set for DA then the SA from the packet is not learned */
+#define ICSSG_FDB_ENTRY_SECURE BIT(5)
+/* If set, it means packet has been seen recently with source address + FID
+ * matching MAC address/FID of entry
+ */
+#define ICSSG_FDB_ENTRY_TOUCHED BIT(6)
+/* Set if entry is valid */
+#define ICSSG_FDB_ENTRY_VALID BIT(7)
+
+/**
+ * struct prueth_vlan_tbl - VLAN table entries struct in ICSSG SMEM
+ * @fid_c1: membership and forwarding rules flag to this table. See
+ * above to defines for bit definitions
+ * @fid: FDB index for this VID (there is 1-1 mapping b/w VID and FID)
+ */
+struct prueth_vlan_tbl {
+ u8 fid_c1;
+ u8 fid;
+} __packed;
+
+/**
+ * struct prueth_fdb_slot - Result of FDB slot lookup
+ * @mac: MAC address
+ * @fid: fid to be associated with MAC
+ * @fid_c2: FID_C2 entry for this MAC
+ */
+struct prueth_fdb_slot {
+ u8 mac[ETH_ALEN];
+ u8 fid;
+ u8 fid_c2;
+} __packed;
+
+enum icssg_ietfpe_verify_states {
+ ICSSG_IETFPE_STATE_UNKNOWN = 0,
+ ICSSG_IETFPE_STATE_INITIAL,
+ ICSSG_IETFPE_STATE_VERIFYING,
+ ICSSG_IETFPE_STATE_SUCCEEDED,
+ ICSSG_IETFPE_STATE_FAILED,
+ ICSSG_IETFPE_STATE_DISABLED
+};
+#endif /* __NET_TI_ICSSG_CONFIG_H */
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
index 8512f19a9b4d..e93488a79dbf 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.h
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
@@ -194,4 +194,19 @@ static inline int prueth_emac_slice(struct prueth_emac *emac)
}
}
+/* Classifier helpers */
+void icssg_class_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac);
+void icssg_class_set_host_mac_addr(struct regmap *miig_rt, const u8 *mac);
+void icssg_class_disable(struct regmap *miig_rt, int slice);
+void icssg_class_default(struct regmap *miig_rt, int slice, bool allmulti);
+void icssg_ft1_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac_addr);
+
+/* config helpers */
+void icssg_config_ipg(struct prueth_emac *emac);
+int icssg_config(struct prueth *prueth, struct prueth_emac *emac,
+ int slice);
+int emac_set_port_state(struct prueth_emac *emac,
+ enum icssg_port_state_cmd state);
+void icssg_config_set_speed(struct prueth_emac *emac);
+
#endif /* __NET_TI_ICSSG_PRUETH_H */
--
2.34.1
Hello:
This series was applied to netdev/net-next.git (main)
by David S. Miller <[email protected]>:
On Tue, 1 Aug 2023 14:44:18 +0530 you wrote:
> The Programmable Real-time Unit and Industrial Communication Subsystem
> Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
> SoCs. This subsystem is provided for the use cases like the implementation
> of custom peripheral interfaces, offloading of tasks from the other
> processor cores of the SoC, etc.
>
> The subsystem includes many accelerators for data processing like
> multiplier and multiplier-accumulator. It also has peripherals like
> UART, MII/RGMII, MDIO, etc. Every ICSSG core includes two 32-bit
> load/store RISC CPU cores called PRUs.
>
> [...]
Here is the summary with links:
- [v13,01/10] net: ti: icssg-prueth: Add Firmware Interface for ICSSG Ethernet driver.
https://git.kernel.org/netdev/net-next/c/61f4d2044aeb
- [v13,02/10] net: ti: icssg-prueth: Add mii helper apis and macros
https://git.kernel.org/netdev/net-next/c/b6ba7752149d
- [v13,03/10] net: ti: icssg-prueth: Add Firmware config and classification APIs.
https://git.kernel.org/netdev/net-next/c/e9b4ece7d74b
- [v13,04/10] net: ti: icssg-prueth: Add icssg queues APIs and macros
https://git.kernel.org/netdev/net-next/c/b8d5008f8c51
- [v13,05/10] dt-bindings: net: Add ICSSG Ethernet
https://git.kernel.org/netdev/net-next/c/172e604a8c62
- [v13,06/10] net: ti: icssg-prueth: Add ICSSG ethernet driver
https://git.kernel.org/netdev/net-next/c/128d5874c082
- [v13,07/10] net: ti: icssg-prueth: Add ICSSG Stats
https://git.kernel.org/netdev/net-next/c/c1e10d5dc7a1
- [v13,08/10] net: ti: icssg-prueth: Add Standard network staticstics
https://git.kernel.org/netdev/net-next/c/c2f67d192351
- [v13,09/10] net: ti: icssg-prueth: Add ethtool ops for ICSSG Ethernet driver
https://git.kernel.org/netdev/net-next/c/8fb86b0dcaed
- [v13,10/10] net: ti: icssg-prueth: Add Power management support
https://git.kernel.org/netdev/net-next/c/a46750a13bb0
You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html