Due to non-addressable regions in J721S2 SOC wkup_pmx was split
into four regions from wkup_pmx0 to wkup_pmx3.
After split while updating the pin mux references to newly defined
four wkup_pmx, pin mux for OSPI0 was left.
Pin mux for OSPI0 is spread over two range wkup_pmx0
and wkup_pmx1, along with correcting pin mux for ospi
adding correct pin mux setting within ospi node.
Fixes: 6bc829ceea41 ("arm64: dts: ti: k3-j721s2: Fix wkup pinmux range")
Signed-off-by: Udit Kumar <[email protected]>
---
Logs with v2
https://gist.github.com/uditkumarti/701f5f21edd4a10d22abe5f70a752279
Change log:
Changes in v2:
Changed name of pin mux to align with
https://lore.kernel.org/all/[email protected]/ patch
v1: https://lore.kernel.org/all/[email protected]/
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 13 ++++++++++---
1 file changed, 10 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index d57dd43da0ef..fd1d6c884736 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -45,8 +45,6 @@ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
- J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
- J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
@@ -61,6 +59,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
};
};
+&wkup_pmx1 {
+ mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+ J721S2_WKUP_IOPAD(0x004, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
@@ -127,7 +134,7 @@ &main_mcan16 {
&ospi0 {
status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
compatible = "jedec,spi-nor";
--
2.34.1