Now the wait time for one-shot is 140ms, instead of the old 141
(removed the 1ms error).
Used enums and while loops to replace switch for selecting and getting
update interval from conversion rate bits.
Divided the write_alarm_val function into 2 functions. The new function
is more generic: it can be used not only for alarm writes, but for any
kind of writes which require the device to be in shutdown mode.
Signed-off-by: Daniel Matyas <[email protected]>
---
v2 -> v3: No change.
v2: Added patch.
Documentation/hwmon/max31827.rst | 4 +-
drivers/hwmon/max31827.c | 127 ++++++++++++++-----------------
2 files changed, 58 insertions(+), 73 deletions(-)
diff --git a/Documentation/hwmon/max31827.rst b/Documentation/hwmon/max31827.rst
index b0971d05b8a4..9a1055a007cf 100644
--- a/Documentation/hwmon/max31827.rst
+++ b/Documentation/hwmon/max31827.rst
@@ -73,8 +73,8 @@ the conversion frequency to 1 conv/s. The conversion time varies depending on
the resolution. The conversion time doubles with every bit of increased
resolution. For 10 bit resolution 35ms are needed, while for 12 bit resolution
(default) 140ms. When chip is in shutdown mode and a read operation is
-requested, one-shot is triggered, the device waits for 140 (conversion time) + 1
-(error) ms, and only after that is the temperature value register read.
+requested, one-shot is triggered, the device waits for 140 (conversion time) ms,
+and only after that is the temperature value register read.
The LSB of the temperature values is 0.0625 degrees Celsius, but the values of
the temperatures are displayed in milli-degrees. This means, that some data is
diff --git a/drivers/hwmon/max31827.c b/drivers/hwmon/max31827.c
index 602f4e4f81ff..f05762219995 100644
--- a/drivers/hwmon/max31827.c
+++ b/drivers/hwmon/max31827.c
@@ -25,20 +25,32 @@
#define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
-#define MAX31827_12_BIT_CNV_TIME 141
-
-#define MAX31827_CNV_1_DIV_64_HZ 0x1
-#define MAX31827_CNV_1_DIV_32_HZ 0x2
-#define MAX31827_CNV_1_DIV_16_HZ 0x3
-#define MAX31827_CNV_1_DIV_4_HZ 0x4
-#define MAX31827_CNV_1_HZ 0x5
-#define MAX31827_CNV_4_HZ 0x6
-#define MAX31827_CNV_8_HZ 0x7
+#define MAX31827_12_BIT_CNV_TIME 140
#define MAX31827_16_BIT_TO_M_DGR(x) (sign_extend32(x, 15) * 1000 / 16)
#define MAX31827_M_DGR_TO_16_BIT(x) (((x) << 4) / 1000)
#define MAX31827_DEVICE_ENABLE(x) ((x) ? 0xA : 0x0)
+enum max31827_cnv {
+ MAX31827_CNV_1_DIV_64_HZ = 1,
+ MAX31827_CNV_1_DIV_32_HZ,
+ MAX31827_CNV_1_DIV_16_HZ,
+ MAX31827_CNV_1_DIV_4_HZ,
+ MAX31827_CNV_1_HZ,
+ MAX31827_CNV_4_HZ,
+ MAX31827_CNV_8_HZ,
+};
+
+static const u16 max31827_conversions[] = {
+ [MAX31827_CNV_1_DIV_64_HZ] = 64000,
+ [MAX31827_CNV_1_DIV_32_HZ] = 32000,
+ [MAX31827_CNV_1_DIV_16_HZ] = 16000,
+ [MAX31827_CNV_1_DIV_4_HZ] = 4000,
+ [MAX31827_CNV_1_HZ] = 1000,
+ [MAX31827_CNV_4_HZ] = 250,
+ [MAX31827_CNV_8_HZ] = 125,
+};
+
struct max31827_state {
/*
* Prevent simultaneous access to the i2c client.
@@ -54,15 +66,13 @@ static const struct regmap_config max31827_regmap = {
.max_register = 0xA,
};
-static int write_alarm_val(struct max31827_state *st, unsigned int reg,
- long val)
+static int shutdown_write(struct max31827_state *st, unsigned int reg,
+ unsigned int val)
{
unsigned int cfg;
- unsigned int tmp;
+ unsigned int cnv_rate;
int ret;
- val = MAX31827_M_DGR_TO_16_BIT(val);
-
/*
* Before the Temperature Threshold Alarm and Alarm Hysteresis Threshold
* register values are changed over I2C, the part must be in shutdown
@@ -82,9 +92,10 @@ static int write_alarm_val(struct max31827_state *st, unsigned int reg,
if (ret)
goto unlock;
- tmp = cfg & ~(MAX31827_CONFIGURATION_1SHOT_MASK |
+ cnv_rate = MAX31827_CONFIGURATION_CNV_RATE_MASK & cfg;
+ cfg = cfg & ~(MAX31827_CONFIGURATION_1SHOT_MASK |
MAX31827_CONFIGURATION_CNV_RATE_MASK);
- ret = regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, tmp);
+ ret = regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, cfg);
if (ret)
goto unlock;
@@ -92,13 +103,23 @@ static int write_alarm_val(struct max31827_state *st, unsigned int reg,
if (ret)
goto unlock;
- ret = regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, cfg);
+ ret = regmap_update_bits(st->regmap, MAX31827_CONFIGURATION_REG,
+ MAX31827_CONFIGURATION_CNV_RATE_MASK,
+ cnv_rate);
unlock:
mutex_unlock(&st->lock);
return ret;
}
+static int write_alarm_val(struct max31827_state *st, unsigned int reg,
+ long val)
+{
+ val = MAX31827_M_DGR_TO_16_BIT(val);
+
+ return shutdown_write(st, reg, val);
+}
+
static umode_t max31827_is_visible(const void *state,
enum hwmon_sensor_types type, u32 attr,
int channel)
@@ -243,32 +264,7 @@ static int max31827_read(struct device *dev, enum hwmon_sensor_types type,
uval = FIELD_GET(MAX31827_CONFIGURATION_CNV_RATE_MASK,
uval);
- switch (uval) {
- case MAX31827_CNV_1_DIV_64_HZ:
- *val = 64000;
- break;
- case MAX31827_CNV_1_DIV_32_HZ:
- *val = 32000;
- break;
- case MAX31827_CNV_1_DIV_16_HZ:
- *val = 16000;
- break;
- case MAX31827_CNV_1_DIV_4_HZ:
- *val = 4000;
- break;
- case MAX31827_CNV_1_HZ:
- *val = 1000;
- break;
- case MAX31827_CNV_4_HZ:
- *val = 250;
- break;
- case MAX31827_CNV_8_HZ:
- *val = 125;
- break;
- default:
- *val = 0;
- break;
- }
+ *val = max31827_conversions[uval];
}
break;
@@ -284,6 +280,7 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
u32 attr, int channel, long val)
{
struct max31827_state *st = dev_get_drvdata(dev);
+ int res = 1;
int ret;
switch (type) {
@@ -333,39 +330,27 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
if (!st->enable)
return -EINVAL;
- switch (val) {
- case 125:
- val = MAX31827_CNV_8_HZ;
- break;
- case 250:
- val = MAX31827_CNV_4_HZ;
- break;
- case 1000:
- val = MAX31827_CNV_1_HZ;
- break;
- case 4000:
- val = MAX31827_CNV_1_DIV_4_HZ;
- break;
- case 16000:
- val = MAX31827_CNV_1_DIV_16_HZ;
- break;
- case 32000:
- val = MAX31827_CNV_1_DIV_32_HZ;
- break;
- case 64000:
- val = MAX31827_CNV_1_DIV_64_HZ;
- break;
- default:
- return -EINVAL;
- }
+ /*
+ * Convert the desired conversion rate into register
+ * bits. res is already initialized with 1.
+ *
+ * This was inspired by lm73 driver.
+ */
+ while (res < ARRAY_SIZE(max31827_conversions) &&
+ val < max31827_conversions[res])
+ res++;
+
+ if (res == ARRAY_SIZE(max31827_conversions) ||
+ val != max31827_conversions[res])
+ return -EOPNOTSUPP;
- val = FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
- val);
+ res = FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
+ res);
return regmap_update_bits(st->regmap,
MAX31827_CONFIGURATION_REG,
MAX31827_CONFIGURATION_CNV_RATE_MASK,
- val);
+ res);
}
break;
--
2.34.1
Added custom channel-specific (temp1) attribute for resolution. The wait
time for a conversion in one-shot mode (enable = 0) depends on the
resolution.
When resolution is 12-bit, the conversion time is 140ms, but the minimum
update_interval is 125ms. Handled this problem by waiting an additional
15ms (125ms + 15ms = 140ms).
Signed-off-by: Daniel Matyas <[email protected]>
---
v2 -> v3: Fixed indentation problems in .rst.
v1 -> v2: Changed subject. Separated patch. Removed timeout sysfs
attribute and kept only resolution. Added temp1_ prefix to resolution.
Changed value of resolution from bits to milli-degrees Celsius. Added
appropriate documentation.
Documentation/hwmon/max31827.rst | 29 +++++--
drivers/hwmon/max31827.c | 128 ++++++++++++++++++++++++++++---
2 files changed, 141 insertions(+), 16 deletions(-)
diff --git a/Documentation/hwmon/max31827.rst b/Documentation/hwmon/max31827.rst
index a8bbfb85dd02..d86225a31961 100644
--- a/Documentation/hwmon/max31827.rst
+++ b/Documentation/hwmon/max31827.rst
@@ -90,11 +90,28 @@ the data sheet are:
Enabling the device when it is already enabled has the side effect of setting
the conversion frequency to 1 conv/s. The conversion time varies depending on
-the resolution. The conversion time doubles with every bit of increased
-resolution. For 10 bit resolution 35ms are needed, while for 12 bit resolution
-(default) 140ms. When chip is in shutdown mode and a read operation is
-requested, one-shot is triggered, the device waits for 140 (conversion time) ms,
-and only after that is the temperature value register read.
+the resolution.
+
+The conversion time doubles with every bit of increased resolution. The
+available resolutions are:
+
+- 8 bit -> 8.75 ms conversion time
+- 9 bit -> 17.5 ms conversion time
+- 10 bit -> 35 ms conversion time
+- 12 bit (default) -> 140 ms conversion time
+
+There is a temp1_resolution attribute which indicates the unit change in the
+input temperature in milli-degrees C.
+
+- 1000 mC -> 8 bit
+- 500 mC -> 9 bit
+- 250 mC -> 10 bit
+- 62 mC -> 12 bit (default) - actually this is 62.5, but the file returns 62
+
+When chip is in shutdown mode and a read operation is requested, one-shot is
+triggered, the device waits for <conversion time> ms, and only after that is
+the temperature value register read. Note that the conversion times are rounded
+up to the nearest possible integer.
The LSB of the temperature values is 0.0625 degrees Celsius, but the values of
the temperatures are displayed in milli-degrees. This means, that some data is
@@ -117,4 +134,4 @@ corresponding status bits.
Notes
-----
-PEC and resolution are not implemented.
+PEC is not implemented.
diff --git a/drivers/hwmon/max31827.c b/drivers/hwmon/max31827.c
index 1f29a1f5759d..848a0f3fd821 100644
--- a/drivers/hwmon/max31827.c
+++ b/drivers/hwmon/max31827.c
@@ -43,6 +43,9 @@
#define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
+#define MAX31827_8_BIT_CNV_TIME 9
+#define MAX31827_9_BIT_CNV_TIME 18
+#define MAX31827_10_BIT_CNV_TIME 35
#define MAX31827_12_BIT_CNV_TIME 140
#define MAX31827_ALRM_POL_LOW 0x0
@@ -54,6 +57,7 @@
#define MAX31827_16_BIT_TO_M_DGR(x) (sign_extend32(x, 15) * 1000 / 16)
#define MAX31827_M_DGR_TO_16_BIT(x) (((x) << 4) / 1000)
#define MAX31827_DEVICE_ENABLE(x) ((x) ? 0xA : 0x0)
+#define MAX31827_FLT_Q
enum chips { max31827, max31828, max31829 };
@@ -77,6 +81,27 @@ static const u16 max31827_conversions[] = {
[MAX31827_CNV_8_HZ] = 125,
};
+enum max31827_resolution {
+ MAX31827_RES_8_BIT = 0,
+ MAX31827_RES_9_BIT,
+ MAX31827_RES_10_BIT,
+ MAX31827_RES_12_BIT,
+};
+
+static const u16 max31827_resolutions[] = {
+ [MAX31827_RES_8_BIT] = 1000,
+ [MAX31827_RES_9_BIT] = 500,
+ [MAX31827_RES_10_BIT] = 250,
+ [MAX31827_RES_12_BIT] = 62,
+};
+
+static const u16 max31827_conv_times[] = {
+ [MAX31827_RES_8_BIT] = MAX31827_8_BIT_CNV_TIME,
+ [MAX31827_RES_9_BIT] = MAX31827_9_BIT_CNV_TIME,
+ [MAX31827_RES_10_BIT] = MAX31827_10_BIT_CNV_TIME,
+ [MAX31827_RES_12_BIT] = MAX31827_12_BIT_CNV_TIME,
+};
+
struct max31827_state {
/*
* Prevent simultaneous access to the i2c client.
@@ -84,6 +109,8 @@ struct max31827_state {
struct mutex lock;
struct regmap *regmap;
bool enable;
+ unsigned int resolution;
+ unsigned int update_interval;
struct i2c_client *client;
};
@@ -101,9 +128,9 @@ static int shutdown_write(struct max31827_state *st, unsigned int reg,
int ret;
/*
- * Before the Temperature Threshold Alarm and Alarm Hysteresis Threshold
- * register values are changed over I2C, the part must be in shutdown
- * mode.
+ * Before the Temperature Threshold Alarm, Alarm Hysteresis Threshold
+ * and Resolution bits from Configuration register are changed over I2C,
+ * the part must be in shutdown mode.
*
* Mutex is used to ensure, that some other process doesn't change the
* configuration register.
@@ -214,9 +241,18 @@ static int max31827_read(struct device *dev, enum hwmon_sensor_types type,
mutex_unlock(&st->lock);
return ret;
}
-
- msleep(MAX31827_12_BIT_CNV_TIME);
+ msleep(max31827_conv_times[st->resolution]);
}
+
+ /*
+ * For 12-bit resolution the conversion time is 140 ms,
+ * thus an additional 15 ms is needed to complete the
+ * conversion: 125 ms + 15 ms = 140 ms
+ */
+ if (max31827_resolutions[st->resolution] == 12 &&
+ st->update_interval == 125)
+ usleep_range(15000, 20000);
+
ret = regmap_read(st->regmap, MAX31827_T_REG, &uval);
mutex_unlock(&st->lock);
@@ -374,10 +410,14 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
res = FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
res);
- return regmap_update_bits(st->regmap,
- MAX31827_CONFIGURATION_REG,
- MAX31827_CONFIGURATION_CNV_RATE_MASK,
- res);
+ ret = regmap_update_bits(st->regmap,
+ MAX31827_CONFIGURATION_REG,
+ MAX31827_CONFIGURATION_CNV_RATE_MASK,
+ res);
+ if (ret)
+ return ret;
+
+ st->update_interval = val;
}
break;
@@ -388,6 +428,74 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
return -EOPNOTSUPP;
}
+static ssize_t temp1_resolution_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct max31827_state *st = dev_get_drvdata(dev);
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(st->regmap, MAX31827_CONFIGURATION_REG, &val);
+ if (ret)
+ return ret;
+
+ val = FIELD_GET(MAX31827_CONFIGURATION_RESOLUTION_MASK, val);
+
+ return scnprintf(buf, PAGE_SIZE, "%u\n", max31827_resolutions[val]);
+}
+
+static ssize_t temp1_resolution_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct max31827_state *st = dev_get_drvdata(dev);
+ unsigned int idx = 0;
+ unsigned int val, cfg;
+ int ret;
+
+ ret = kstrtouint(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ /*
+ * Convert the desired conversion rate into register
+ * bits. idx is already initialized with 1.
+ *
+ * This was inspired by lm73 driver.
+ */
+ while (idx < ARRAY_SIZE(max31827_resolutions) &&
+ val < max31827_resolutions[idx])
+ idx++;
+
+ if (idx == ARRAY_SIZE(max31827_resolutions) ||
+ val != max31827_resolutions[idx])
+ return -EOPNOTSUPP;
+
+ st->resolution = idx;
+
+ ret = regmap_read(st->regmap, MAX31827_CONFIGURATION_REG, &cfg);
+ if (ret)
+ return ret;
+
+ cfg = (cfg & ~MAX31827_CONFIGURATION_RESOLUTION_MASK) |
+ FIELD_PREP(MAX31827_CONFIGURATION_RESOLUTION_MASK, idx);
+ cfg &= ~(MAX31827_CONFIGURATION_CNV_RATE_MASK |
+ MAX31827_CONFIGURATION_1SHOT_MASK);
+
+ ret = shutdown_write(st, MAX31827_CONFIGURATION_REG, cfg);
+
+ return (ret) ? ret : count;
+}
+
+static DEVICE_ATTR_RW(temp1_resolution);
+
+static struct attribute *max31827_attrs[] = {
+ &dev_attr_temp1_resolution.attr,
+ NULL
+};
+ATTRIBUTE_GROUPS(max31827);
+
static const struct i2c_device_id max31827_i2c_ids[] = {
{ "max31827", max31827 },
{ "max31828", max31828 },
@@ -528,7 +636,7 @@ static int max31827_probe(struct i2c_client *client)
hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, st,
&max31827_chip_info,
- NULL);
+ max31827_groups);
return PTR_ERR_OR_ZERO(hwmon_dev);
}
--
2.34.1
Used fwnode to retrieve data from the devicetree in the init_client
function.
If the uint32 properties are not present, the default values are used
for max31827 chip.
Signed-off-by: Daniel Matyas <[email protected]>
---
v2 -> v3: Separated patch into 2. Fixed 'WARNING: Unexpected
indentation.'
Reported-by: kernel test robot <[email protected]>
v2: Added patch
Documentation/hwmon/max31827.rst | 48 ++++++++++++++----
drivers/hwmon/max31827.c | 85 +++++++++++++++++++++++++++++---
2 files changed, 116 insertions(+), 17 deletions(-)
diff --git a/Documentation/hwmon/max31827.rst b/Documentation/hwmon/max31827.rst
index 9a1055a007cf..a8bbfb85dd02 100644
--- a/Documentation/hwmon/max31827.rst
+++ b/Documentation/hwmon/max31827.rst
@@ -52,13 +52,21 @@ MAX31827 has low and over temperature alarms with an effective value and a
hysteresis value: -40 and -30 degrees for under temperature alarm and +100 and
+90 degrees for over temperature alarm.
-The alarm can be configured in comparator and interrupt mode. Currently only
-comparator mode is implemented. In Comparator mode, the OT/UT status bits have a
-value of 1 when the temperature rises above the TH value or falls below TL,
-which is also subject to the Fault Queue selection. OT status returns to 0 when
-the temperature drops below the TH_HYST value or when shutdown mode is entered.
-Similarly, UT status returns to 0 when the temperature rises above TL_HYST value
-or when shutdown mode is entered.
+The alarm can be configured in comparator and interrupt mode from the
+devicetree. In Comparator mode, the OT/UT status bits have a value of 1 when the
+temperature rises above the TH value or falls below TL, which is also subject to
+the Fault Queue selection. OT status returns to 0 when the temperature drops
+below the TH_HYST value or when shutdown mode is entered. Similarly, UT status
+returns to 0 when the temperature rises above TL_HYST value or when shutdown
+mode is entered.
+
+In interrupt mode exceeding TH also sets OT status to 1, which remains set until
+a read operation is performed on the configuration/status register (max or min
+attribute); at this point, it returns to 0. Once OT status is set to 1 from
+exceeding TH and reset, it is set to 1 again only when the temperature drops
+below TH_HYST. The output remains asserted until it is reset by a read. It is
+set again if the temperature rises above TH, and so on. The same logic applies
+to the operation of the UT status bit.
Putting the MAX31827 into shutdown mode also resets the OT/UT status bits. Note
that if the mode is changed while OT/UT status bits are set, an OT/UT status
@@ -68,6 +76,18 @@ clear the status bits before changing the operating mode.
The conversions can be manual with the one-shot functionality and automatic with
a set frequency. When powered on, the chip measures temperatures with 1 conv/s.
+The conversion rate can be modified with update_interval attribute of the chip.
+Conversion/second = 1/update_interval. Thus, the available options according to
+the data sheet are:
+
+- 64000 (ms) = 1 conv/64 sec
+- 32000 (ms) = 1 conv/32 sec
+- 16000 (ms) = 1 conv/16 sec
+- 4000 (ms) = 1 conv/4 sec
+- 1000 (ms) = 1 conv/sec (default)
+- 250 (ms) = 4 conv/sec
+- 125 (ms) = 8 conv/sec
+
Enabling the device when it is already enabled has the side effect of setting
the conversion frequency to 1 conv/s. The conversion time varies depending on
the resolution. The conversion time doubles with every bit of increased
@@ -83,8 +103,18 @@ in the writing of alarm values too. For positive numbers the user-input value
will always be rounded down to the nearest possible value, for negative numbers
the user-input will always be rounded up to the nearest possible value.
+Bus timeout resets the I2C-compatible interface when SCL is low for more than
+30ms (nominal).
+
+Alarm polarity determines if the active state of the alarm is low or high. The
+behavior for both settings is dependent on the Fault Queue setting. The ALARM
+pin is an open-drain output and requires a pullup resistor to operate.
+
+The Fault Queue bits select how many consecutive temperature faults must occur
+before overtemperature or undertemperature faults are indicated in the
+corresponding status bits.
+
Notes
-----
-Currently fault queue, alarm polarity and resolution cannot be modified.
-PEC is not implemented either.
+PEC and resolution are not implemented.
diff --git a/drivers/hwmon/max31827.c b/drivers/hwmon/max31827.c
index f05762219995..41c440b8a474 100644
--- a/drivers/hwmon/max31827.c
+++ b/drivers/hwmon/max31827.c
@@ -12,6 +12,19 @@
#include <linux/i2c.h>
#include <linux/mutex.h>
#include <linux/regmap.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/of_device.h>
+
+/*
+ * gcc turns __builtin_ffsll() into a call to __ffsdi2(), which is not provided
+ * by every architecture. __ffs64() is available on all architectures, but the
+ * result is not defined if no bits are set.
+ */
+#define max31827__bf_shf(x) \
+ ({ \
+ typeof(x) x_ = (x); \
+ ((x_) != 0) ? __ffs64(x_) : 0x0; \
+ })
#define MAX31827_T_REG 0x0
#define MAX31827_CONFIGURATION_REG 0x2
@@ -22,11 +35,19 @@
#define MAX31827_CONFIGURATION_1SHOT_MASK BIT(0)
#define MAX31827_CONFIGURATION_CNV_RATE_MASK GENMASK(3, 1)
-#define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
-#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
+#define MAX31827_CONFIGURATION_TIMEOUT_MASK BIT(5)
+#define MAX31827_CONFIGURATION_RESOLUTION_MASK GENMASK(7, 6)
+#define MAX31827_CONFIGURATION_ALRM_POL_MASK BIT(8)
+#define MAX31827_CONFIGURATION_COMP_INT_MASK BIT(9)
+#define MAX31827_CONFIGURATION_FLT_Q_MASK GENMASK(11, 10)
+#define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
+#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
#define MAX31827_12_BIT_CNV_TIME 140
+#define MAX31827_ALRM_POL_LOW 0x0
+#define MAX31827_FLT_Q_1 0x0
+
#define MAX31827_16_BIT_TO_M_DGR(x) (sign_extend32(x, 15) * 1000 / 16)
#define MAX31827_M_DGR_TO_16_BIT(x) (((x) << 4) / 1000)
#define MAX31827_DEVICE_ENABLE(x) ((x) ? 0xA : 0x0)
@@ -58,6 +79,7 @@ struct max31827_state {
struct mutex lock;
struct regmap *regmap;
bool enable;
+ struct i2c_client *client;
};
static const struct regmap_config max31827_regmap = {
@@ -361,14 +383,57 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
return -EOPNOTSUPP;
}
-static int max31827_init_client(struct max31827_state *st)
+static int max31827_init_client(struct max31827_state *st,
+ struct fwnode_handle *fwnode)
{
+ bool prop;
+ u32 data, lsb_idx;
+ unsigned int res = 0;
+ int ret;
+
st->enable = true;
+ res |= MAX31827_DEVICE_ENABLE(1);
+
+ res |= MAX31827_CONFIGURATION_RESOLUTION_MASK;
+
+ prop = fwnode_property_read_bool(fwnode, "adi,comp-int");
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_COMP_INT_MASK, prop);
+
+ prop = fwnode_property_read_bool(fwnode, "adi,timeout-enable");
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_TIMEOUT_MASK, !prop);
+
+ if (fwnode_property_present(fwnode, "adi,alrm-pol")) {
+ ret = fwnode_property_read_u32(fwnode, "adi,alrm-pol", &data);
+ if (ret)
+ return ret;
- return regmap_update_bits(st->regmap, MAX31827_CONFIGURATION_REG,
- MAX31827_CONFIGURATION_1SHOT_MASK |
- MAX31827_CONFIGURATION_CNV_RATE_MASK,
- MAX31827_DEVICE_ENABLE(1));
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK, !!data);
+ } else {
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK,
+ MAX31827_ALRM_POL_LOW);
+ }
+
+ if (fwnode_property_present(fwnode, "adi,flt-q")) {
+ ret = fwnode_property_read_u32(fwnode, "adi,flt-q", &data);
+ if (ret)
+ return ret;
+
+ /*
+ * Convert the desired fault queue into register bits.
+ */
+ lsb_idx = max31827__bf_shf(data);
+ if (lsb_idx > 3 || data != BIT(lsb_idx)) {
+ dev_err(&st->client->dev, "Invalid data in fault queue\n");
+ return -EOPNOTSUPP;
+ }
+
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK, lsb_idx);
+ } else {
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK,
+ MAX31827_FLT_Q_1);
+ }
+
+ return regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, res);
}
static const struct hwmon_channel_info *max31827_info[] = {
@@ -396,6 +461,7 @@ static int max31827_probe(struct i2c_client *client)
struct device *dev = &client->dev;
struct device *hwmon_dev;
struct max31827_state *st;
+ struct fwnode_handle *fwnode;
int err;
if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA))
@@ -412,7 +478,10 @@ static int max31827_probe(struct i2c_client *client)
return dev_err_probe(dev, PTR_ERR(st->regmap),
"Failed to allocate regmap.\n");
- err = max31827_init_client(st);
+ st->client = client;
+ fwnode = dev_fwnode(dev);
+
+ err = max31827_init_client(st, fwnode);
if (err)
return err;
--
2.34.1
On 9/14/23 00:59, Daniel Matyas wrote:
> Now the wait time for one-shot is 140ms, instead of the old 141
> (removed the 1ms error).
>
It was explicitly documented that the wait time was 140 + 1 milli-seconds,
presumably to be sure that the conversion is really complete.
Why was this an error ? It was _documented_ that way.
Guenter
> Used enums and while loops to replace switch for selecting and getting
> update interval from conversion rate bits.
>
> Divided the write_alarm_val function into 2 functions. The new function
> is more generic: it can be used not only for alarm writes, but for any
> kind of writes which require the device to be in shutdown mode.
>
> Signed-off-by: Daniel Matyas <[email protected]>
> ---
>
> v2 -> v3: No change.
>
> v2: Added patch.
>
> Documentation/hwmon/max31827.rst | 4 +-
> drivers/hwmon/max31827.c | 127 ++++++++++++++-----------------
> 2 files changed, 58 insertions(+), 73 deletions(-)
>
> diff --git a/Documentation/hwmon/max31827.rst b/Documentation/hwmon/max31827.rst
> index b0971d05b8a4..9a1055a007cf 100644
> --- a/Documentation/hwmon/max31827.rst
> +++ b/Documentation/hwmon/max31827.rst
> @@ -73,8 +73,8 @@ the conversion frequency to 1 conv/s. The conversion time varies depending on
> the resolution. The conversion time doubles with every bit of increased
> resolution. For 10 bit resolution 35ms are needed, while for 12 bit resolution
> (default) 140ms. When chip is in shutdown mode and a read operation is
> -requested, one-shot is triggered, the device waits for 140 (conversion time) + 1
> -(error) ms, and only after that is the temperature value register read.
> +requested, one-shot is triggered, the device waits for 140 (conversion time) ms,
> +and only after that is the temperature value register read.
>
> The LSB of the temperature values is 0.0625 degrees Celsius, but the values of
> the temperatures are displayed in milli-degrees. This means, that some data is
> diff --git a/drivers/hwmon/max31827.c b/drivers/hwmon/max31827.c
> index 602f4e4f81ff..f05762219995 100644
> --- a/drivers/hwmon/max31827.c
> +++ b/drivers/hwmon/max31827.c
> @@ -25,20 +25,32 @@
> #define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
> #define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
>
> -#define MAX31827_12_BIT_CNV_TIME 141
> -
> -#define MAX31827_CNV_1_DIV_64_HZ 0x1
> -#define MAX31827_CNV_1_DIV_32_HZ 0x2
> -#define MAX31827_CNV_1_DIV_16_HZ 0x3
> -#define MAX31827_CNV_1_DIV_4_HZ 0x4
> -#define MAX31827_CNV_1_HZ 0x5
> -#define MAX31827_CNV_4_HZ 0x6
> -#define MAX31827_CNV_8_HZ 0x7
> +#define MAX31827_12_BIT_CNV_TIME 140
>
> #define MAX31827_16_BIT_TO_M_DGR(x) (sign_extend32(x, 15) * 1000 / 16)
> #define MAX31827_M_DGR_TO_16_BIT(x) (((x) << 4) / 1000)
> #define MAX31827_DEVICE_ENABLE(x) ((x) ? 0xA : 0x0)
>
> +enum max31827_cnv {
> + MAX31827_CNV_1_DIV_64_HZ = 1,
> + MAX31827_CNV_1_DIV_32_HZ,
> + MAX31827_CNV_1_DIV_16_HZ,
> + MAX31827_CNV_1_DIV_4_HZ,
> + MAX31827_CNV_1_HZ,
> + MAX31827_CNV_4_HZ,
> + MAX31827_CNV_8_HZ,
> +};
> +
> +static const u16 max31827_conversions[] = {
> + [MAX31827_CNV_1_DIV_64_HZ] = 64000,
> + [MAX31827_CNV_1_DIV_32_HZ] = 32000,
> + [MAX31827_CNV_1_DIV_16_HZ] = 16000,
> + [MAX31827_CNV_1_DIV_4_HZ] = 4000,
> + [MAX31827_CNV_1_HZ] = 1000,
> + [MAX31827_CNV_4_HZ] = 250,
> + [MAX31827_CNV_8_HZ] = 125,
> +};
> +
> struct max31827_state {
> /*
> * Prevent simultaneous access to the i2c client.
> @@ -54,15 +66,13 @@ static const struct regmap_config max31827_regmap = {
> .max_register = 0xA,
> };
>
> -static int write_alarm_val(struct max31827_state *st, unsigned int reg,
> - long val)
> +static int shutdown_write(struct max31827_state *st, unsigned int reg,
> + unsigned int val)
> {
> unsigned int cfg;
> - unsigned int tmp;
> + unsigned int cnv_rate;
> int ret;
>
> - val = MAX31827_M_DGR_TO_16_BIT(val);
> -
> /*
> * Before the Temperature Threshold Alarm and Alarm Hysteresis Threshold
> * register values are changed over I2C, the part must be in shutdown
> @@ -82,9 +92,10 @@ static int write_alarm_val(struct max31827_state *st, unsigned int reg,
> if (ret)
> goto unlock;
>
> - tmp = cfg & ~(MAX31827_CONFIGURATION_1SHOT_MASK |
> + cnv_rate = MAX31827_CONFIGURATION_CNV_RATE_MASK & cfg;
> + cfg = cfg & ~(MAX31827_CONFIGURATION_1SHOT_MASK |
> MAX31827_CONFIGURATION_CNV_RATE_MASK);
> - ret = regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, tmp);
> + ret = regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, cfg);
> if (ret)
> goto unlock;
>
> @@ -92,13 +103,23 @@ static int write_alarm_val(struct max31827_state *st, unsigned int reg,
> if (ret)
> goto unlock;
>
> - ret = regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, cfg);
> + ret = regmap_update_bits(st->regmap, MAX31827_CONFIGURATION_REG,
> + MAX31827_CONFIGURATION_CNV_RATE_MASK,
> + cnv_rate);
>
> unlock:
> mutex_unlock(&st->lock);
> return ret;
> }
>
> +static int write_alarm_val(struct max31827_state *st, unsigned int reg,
> + long val)
> +{
> + val = MAX31827_M_DGR_TO_16_BIT(val);
> +
> + return shutdown_write(st, reg, val);
> +}
> +
> static umode_t max31827_is_visible(const void *state,
> enum hwmon_sensor_types type, u32 attr,
> int channel)
> @@ -243,32 +264,7 @@ static int max31827_read(struct device *dev, enum hwmon_sensor_types type,
>
> uval = FIELD_GET(MAX31827_CONFIGURATION_CNV_RATE_MASK,
> uval);
> - switch (uval) {
> - case MAX31827_CNV_1_DIV_64_HZ:
> - *val = 64000;
> - break;
> - case MAX31827_CNV_1_DIV_32_HZ:
> - *val = 32000;
> - break;
> - case MAX31827_CNV_1_DIV_16_HZ:
> - *val = 16000;
> - break;
> - case MAX31827_CNV_1_DIV_4_HZ:
> - *val = 4000;
> - break;
> - case MAX31827_CNV_1_HZ:
> - *val = 1000;
> - break;
> - case MAX31827_CNV_4_HZ:
> - *val = 250;
> - break;
> - case MAX31827_CNV_8_HZ:
> - *val = 125;
> - break;
> - default:
> - *val = 0;
> - break;
> - }
> + *val = max31827_conversions[uval];
> }
> break;
>
> @@ -284,6 +280,7 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
> u32 attr, int channel, long val)
> {
> struct max31827_state *st = dev_get_drvdata(dev);
> + int res = 1;
> int ret;
>
> switch (type) {
> @@ -333,39 +330,27 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
> if (!st->enable)
> return -EINVAL;
>
> - switch (val) {
> - case 125:
> - val = MAX31827_CNV_8_HZ;
> - break;
> - case 250:
> - val = MAX31827_CNV_4_HZ;
> - break;
> - case 1000:
> - val = MAX31827_CNV_1_HZ;
> - break;
> - case 4000:
> - val = MAX31827_CNV_1_DIV_4_HZ;
> - break;
> - case 16000:
> - val = MAX31827_CNV_1_DIV_16_HZ;
> - break;
> - case 32000:
> - val = MAX31827_CNV_1_DIV_32_HZ;
> - break;
> - case 64000:
> - val = MAX31827_CNV_1_DIV_64_HZ;
> - break;
> - default:
> - return -EINVAL;
> - }
> + /*
> + * Convert the desired conversion rate into register
> + * bits. res is already initialized with 1.
> + *
> + * This was inspired by lm73 driver.
> + */
> + while (res < ARRAY_SIZE(max31827_conversions) &&
> + val < max31827_conversions[res])
> + res++;
> +
> + if (res == ARRAY_SIZE(max31827_conversions) ||
> + val != max31827_conversions[res])
> + return -EOPNOTSUPP;
>
> - val = FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
> - val);
> + res = FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
> + res);
>
> return regmap_update_bits(st->regmap,
> MAX31827_CONFIGURATION_REG,
> MAX31827_CONFIGURATION_CNV_RATE_MASK,
> - val);
> + res);
> }
> break;
>
> -----Original Message-----
> From: Guenter Roeck <[email protected]> On Behalf Of Guenter Roeck
> Sent: Saturday, September 16, 2023 2:26 AM
> To: Matyas, Daniel <[email protected]>
> Cc: Jean Delvare <[email protected]>; Rob Herring
> <[email protected]>; Krzysztof Kozlowski
> <[email protected]>; Conor Dooley
> <[email protected]>; Jonathan Corbet <[email protected]>; linux-
> [email protected]; [email protected]; linux-
> [email protected]; [email protected]
> Subject: Re: [PATCH v3 1/5] hwmon: max31827: Make code cleaner
>
> [External]
>
> On 9/14/23 00:59, Daniel Matyas wrote:
> > Now the wait time for one-shot is 140ms, instead of the old 141
> > (removed the 1ms error).
> >
>
> It was explicitly documented that the wait time was 140 + 1 milli-seconds,
> presumably to be sure that the conversion is really complete.
>
> Why was this an error ? It was _documented_ that way.
>
> Guenter
>
Well... actually I developed the driver initially and I wrote the documentation, so I know. I decided to remove the error milli-second, because I realized, it isn't really needed. There is no reference about it in the documentation of the chip, and frankly, I didn’t actually encounter any error which would need the 1 milli-second.
This way, the wait time is more exact and the correspondence with the chip documentation becomes quite straightforward.
Daniel
> > Used enums and while loops to replace switch for selecting and getting
> > update interval from conversion rate bits.
> >
> > Divided the write_alarm_val function into 2 functions. The new
> > function is more generic: it can be used not only for alarm writes,
> > but for any kind of writes which require the device to be in shutdown
> mode.
> >
> > Signed-off-by: Daniel Matyas <[email protected]>
> > ---
> >
> > v2 -> v3: No change.
> >
> > v2: Added patch.
> >
> > Documentation/hwmon/max31827.rst | 4 +-
> > drivers/hwmon/max31827.c | 127 ++++++++++++++-----------------
> > 2 files changed, 58 insertions(+), 73 deletions(-)
> >
> > diff --git a/Documentation/hwmon/max31827.rst
> > b/Documentation/hwmon/max31827.rst
> > index b0971d05b8a4..9a1055a007cf 100644
> > --- a/Documentation/hwmon/max31827.rst
> > +++ b/Documentation/hwmon/max31827.rst
> > @@ -73,8 +73,8 @@ the conversion frequency to 1 conv/s. The
> conversion time varies depending on
> > the resolution. The conversion time doubles with every bit of increased
> > resolution. For 10 bit resolution 35ms are needed, while for 12 bit
> resolution
> > (default) 140ms. When chip is in shutdown mode and a read operation
> > is -requested, one-shot is triggered, the device waits for 140
> > (conversion time) + 1
> > -(error) ms, and only after that is the temperature value register read.
> > +requested, one-shot is triggered, the device waits for 140
> > +(conversion time) ms, and only after that is the temperature value
> register read.
> >
> > The LSB of the temperature values is 0.0625 degrees Celsius, but the
> values of
> > the temperatures are displayed in milli-degrees. This means, that
> > some data is diff --git a/drivers/hwmon/max31827.c
> > b/drivers/hwmon/max31827.c index 602f4e4f81ff..f05762219995
> 100644
> > --- a/drivers/hwmon/max31827.c
> > +++ b/drivers/hwmon/max31827.c
> > @@ -25,20 +25,32 @@
> > #define MAX31827_CONFIGURATION_U_TEMP_STAT_MASK BIT(14)
> > #define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
> >
> > -#define MAX31827_12_BIT_CNV_TIME 141
> > -
> > -#define MAX31827_CNV_1_DIV_64_HZ 0x1
> > -#define MAX31827_CNV_1_DIV_32_HZ 0x2
> > -#define MAX31827_CNV_1_DIV_16_HZ 0x3
> > -#define MAX31827_CNV_1_DIV_4_HZ 0x4
> > -#define MAX31827_CNV_1_HZ 0x5
> > -#define MAX31827_CNV_4_HZ 0x6
> > -#define MAX31827_CNV_8_HZ 0x7
> > +#define MAX31827_12_BIT_CNV_TIME 140
> >
> > #define MAX31827_16_BIT_TO_M_DGR(x) (sign_extend32(x, 15) *
> 1000 / 16)
> > #define MAX31827_M_DGR_TO_16_BIT(x) (((x) << 4) / 1000)
> > #define MAX31827_DEVICE_ENABLE(x) ((x) ? 0xA : 0x0)
> >
> > +enum max31827_cnv {
> > + MAX31827_CNV_1_DIV_64_HZ = 1,
> > + MAX31827_CNV_1_DIV_32_HZ,
> > + MAX31827_CNV_1_DIV_16_HZ,
> > + MAX31827_CNV_1_DIV_4_HZ,
> > + MAX31827_CNV_1_HZ,
> > + MAX31827_CNV_4_HZ,
> > + MAX31827_CNV_8_HZ,
> > +};
> > +
> > +static const u16 max31827_conversions[] = {
> > + [MAX31827_CNV_1_DIV_64_HZ] = 64000,
> > + [MAX31827_CNV_1_DIV_32_HZ] = 32000,
> > + [MAX31827_CNV_1_DIV_16_HZ] = 16000,
> > + [MAX31827_CNV_1_DIV_4_HZ] = 4000,
> > + [MAX31827_CNV_1_HZ] = 1000,
> > + [MAX31827_CNV_4_HZ] = 250,
> > + [MAX31827_CNV_8_HZ] = 125,
> > +};
> > +
> > struct max31827_state {
> > /*
> > * Prevent simultaneous access to the i2c client.
> > @@ -54,15 +66,13 @@ static const struct regmap_config
> max31827_regmap = {
> > .max_register = 0xA,
> > };
> >
> > -static int write_alarm_val(struct max31827_state *st, unsigned int reg,
> > - long val)
> > +static int shutdown_write(struct max31827_state *st, unsigned int reg,
> > + unsigned int val)
> > {
> > unsigned int cfg;
> > - unsigned int tmp;
> > + unsigned int cnv_rate;
> > int ret;
> >
> > - val = MAX31827_M_DGR_TO_16_BIT(val);
> > -
> > /*
> > * Before the Temperature Threshold Alarm and Alarm Hysteresis
> Threshold
> > * register values are changed over I2C, the part must be in
> > shutdown @@ -82,9 +92,10 @@ static int write_alarm_val(struct
> max31827_state *st, unsigned int reg,
> > if (ret)
> > goto unlock;
> >
> > - tmp = cfg & ~(MAX31827_CONFIGURATION_1SHOT_MASK |
> > + cnv_rate = MAX31827_CONFIGURATION_CNV_RATE_MASK & cfg;
> > + cfg = cfg & ~(MAX31827_CONFIGURATION_1SHOT_MASK |
> > MAX31827_CONFIGURATION_CNV_RATE_MASK);
> > - ret = regmap_write(st->regmap,
> MAX31827_CONFIGURATION_REG, tmp);
> > + ret = regmap_write(st->regmap,
> MAX31827_CONFIGURATION_REG, cfg);
> > if (ret)
> > goto unlock;
> >
> > @@ -92,13 +103,23 @@ static int write_alarm_val(struct
> max31827_state *st, unsigned int reg,
> > if (ret)
> > goto unlock;
> >
> > - ret = regmap_write(st->regmap,
> MAX31827_CONFIGURATION_REG, cfg);
> > + ret = regmap_update_bits(st->regmap,
> MAX31827_CONFIGURATION_REG,
> > +
> MAX31827_CONFIGURATION_CNV_RATE_MASK,
> > + cnv_rate);
> >
> > unlock:
> > mutex_unlock(&st->lock);
> > return ret;
> > }
> >
> > +static int write_alarm_val(struct max31827_state *st, unsigned int reg,
> > + long val)
> > +{
> > + val = MAX31827_M_DGR_TO_16_BIT(val);
> > +
> > + return shutdown_write(st, reg, val); }
> > +
> > static umode_t max31827_is_visible(const void *state,
> > enum hwmon_sensor_types type, u32
> attr,
> > int channel)
> > @@ -243,32 +264,7 @@ static int max31827_read(struct device *dev,
> enum
> > hwmon_sensor_types type,
> >
> > uval =
> FIELD_GET(MAX31827_CONFIGURATION_CNV_RATE_MASK,
> > uval);
> > - switch (uval) {
> > - case MAX31827_CNV_1_DIV_64_HZ:
> > - *val = 64000;
> > - break;
> > - case MAX31827_CNV_1_DIV_32_HZ:
> > - *val = 32000;
> > - break;
> > - case MAX31827_CNV_1_DIV_16_HZ:
> > - *val = 16000;
> > - break;
> > - case MAX31827_CNV_1_DIV_4_HZ:
> > - *val = 4000;
> > - break;
> > - case MAX31827_CNV_1_HZ:
> > - *val = 1000;
> > - break;
> > - case MAX31827_CNV_4_HZ:
> > - *val = 250;
> > - break;
> > - case MAX31827_CNV_8_HZ:
> > - *val = 125;
> > - break;
> > - default:
> > - *val = 0;
> > - break;
> > - }
> > + *val = max31827_conversions[uval];
> > }
> > break;
> >
> > @@ -284,6 +280,7 @@ static int max31827_write(struct device *dev,
> enum hwmon_sensor_types type,
> > u32 attr, int channel, long val)
> > {
> > struct max31827_state *st = dev_get_drvdata(dev);
> > + int res = 1;
> > int ret;
> >
> > switch (type) {
> > @@ -333,39 +330,27 @@ static int max31827_write(struct device *dev,
> enum hwmon_sensor_types type,
> > if (!st->enable)
> > return -EINVAL;
> >
> > - switch (val) {
> > - case 125:
> > - val = MAX31827_CNV_8_HZ;
> > - break;
> > - case 250:
> > - val = MAX31827_CNV_4_HZ;
> > - break;
> > - case 1000:
> > - val = MAX31827_CNV_1_HZ;
> > - break;
> > - case 4000:
> > - val = MAX31827_CNV_1_DIV_4_HZ;
> > - break;
> > - case 16000:
> > - val = MAX31827_CNV_1_DIV_16_HZ;
> > - break;
> > - case 32000:
> > - val = MAX31827_CNV_1_DIV_32_HZ;
> > - break;
> > - case 64000:
> > - val = MAX31827_CNV_1_DIV_64_HZ;
> > - break;
> > - default:
> > - return -EINVAL;
> > - }
> > + /*
> > + * Convert the desired conversion rate into
> register
> > + * bits. res is already initialized with 1.
> > + *
> > + * This was inspired by lm73 driver.
> > + */
> > + while (res < ARRAY_SIZE(max31827_conversions)
> &&
> > + val < max31827_conversions[res])
> > + res++;
> > +
> > + if (res == ARRAY_SIZE(max31827_conversions) ||
> > + val != max31827_conversions[res])
> > + return -EOPNOTSUPP;
> >
> > - val =
> FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
> > - val);
> > + res =
> FIELD_PREP(MAX31827_CONFIGURATION_CNV_RATE_MASK,
> > + res);
> >
> > return regmap_update_bits(st->regmap,
> >
> MAX31827_CONFIGURATION_REG,
> >
> MAX31827_CONFIGURATION_CNV_RATE_MASK,
> > - val);
> > + res);
> > }
> > break;
> >
On 9/18/23 02:25, Matyas, Daniel wrote:
>
>
>> -----Original Message-----
>> From: Guenter Roeck <[email protected]> On Behalf Of Guenter Roeck
>> Sent: Saturday, September 16, 2023 2:26 AM
>> To: Matyas, Daniel <[email protected]>
>> Cc: Jean Delvare <[email protected]>; Rob Herring
>> <[email protected]>; Krzysztof Kozlowski
>> <[email protected]>; Conor Dooley
>> <[email protected]>; Jonathan Corbet <[email protected]>; linux-
>> [email protected]; [email protected]; linux-
>> [email protected]; [email protected]
>> Subject: Re: [PATCH v3 1/5] hwmon: max31827: Make code cleaner
>>
>> [External]
>>
>> On 9/14/23 00:59, Daniel Matyas wrote:
>>> Now the wait time for one-shot is 140ms, instead of the old 141
>>> (removed the 1ms error).
>>>
>>
>> It was explicitly documented that the wait time was 140 + 1 milli-seconds,
>> presumably to be sure that the conversion is really complete.
>>
>> Why was this an error ? It was _documented_ that way.
>>
>> Guenter
>>
>
> Well... actually I developed the driver initially and I wrote the documentation, so I know. I decided to remove the error milli-second, because I realized, it isn't really needed. There is no reference about it in the documentation of the chip, and frankly, I didn’t actually encounter any error which would need the 1 milli-second.
>
> This way, the wait time is more exact and the correspondence with the chip documentation becomes quite straightforward.
>
This is all fine, but it is yet another example of more than one logical
change in a single patch, and it has nothing to do with the subject. It
is not a cleanup, but a functional change.
Please split _all_ logical changes into separate patches.
Guenter