From: Thomas Gleixner <[email protected]>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <[email protected]>
---
drivers/tty/serial/ar933x_uart.c | 26 +++++++++++++-------------
1 file changed, 13 insertions(+), 13 deletions(-)
diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index 924c1a89347c..ffd234673177 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -133,9 +133,9 @@ static unsigned int ar933x_uart_tx_empty(struct uart_port *port)
unsigned long flags;
unsigned int rdata;
- spin_lock_irqsave(&up->port.lock, flags);
+ uart_port_lock_irqsave(&up->port, &flags);
rdata = ar933x_uart_read(up, AR933X_UART_DATA_REG);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ uart_port_unlock_irqrestore(&up->port, flags);
return (rdata & AR933X_UART_DATA_TX_CSR) ? 0 : TIOCSER_TEMT;
}
@@ -220,14 +220,14 @@ static void ar933x_uart_break_ctl(struct uart_port *port, int break_state)
container_of(port, struct ar933x_uart_port, port);
unsigned long flags;
- spin_lock_irqsave(&up->port.lock, flags);
+ uart_port_lock_irqsave(&up->port, &flags);
if (break_state == -1)
ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
AR933X_UART_CS_TX_BREAK);
else
ar933x_uart_rmw_clear(up, AR933X_UART_CS_REG,
AR933X_UART_CS_TX_BREAK);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ uart_port_unlock_irqrestore(&up->port, flags);
}
/*
@@ -318,7 +318,7 @@ static void ar933x_uart_set_termios(struct uart_port *port,
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
- spin_lock_irqsave(&up->port.lock, flags);
+ uart_port_lock_irqsave(&up->port, &flags);
/* disable the UART */
ar933x_uart_rmw_clear(up, AR933X_UART_CS_REG,
@@ -352,7 +352,7 @@ static void ar933x_uart_set_termios(struct uart_port *port,
AR933X_UART_CS_IF_MODE_M << AR933X_UART_CS_IF_MODE_S,
AR933X_UART_CS_IF_MODE_DCE << AR933X_UART_CS_IF_MODE_S);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ uart_port_unlock_irqrestore(&up->port, flags);
if (tty_termios_baud_rate(new))
tty_termios_encode_baud_rate(new, baud, baud);
@@ -450,7 +450,7 @@ static irqreturn_t ar933x_uart_interrupt(int irq, void *dev_id)
if ((status & AR933X_UART_CS_HOST_INT) == 0)
return IRQ_NONE;
- spin_lock(&up->port.lock);
+ uart_port_lock(&up->port);
status = ar933x_uart_read(up, AR933X_UART_INT_REG);
status &= ar933x_uart_read(up, AR933X_UART_INT_EN_REG);
@@ -468,7 +468,7 @@ static irqreturn_t ar933x_uart_interrupt(int irq, void *dev_id)
ar933x_uart_tx_chars(up);
}
- spin_unlock(&up->port.lock);
+ uart_port_unlock(&up->port);
return IRQ_HANDLED;
}
@@ -485,7 +485,7 @@ static int ar933x_uart_startup(struct uart_port *port)
if (ret)
return ret;
- spin_lock_irqsave(&up->port.lock, flags);
+ uart_port_lock_irqsave(&up->port, &flags);
/* Enable HOST interrupts */
ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
@@ -498,7 +498,7 @@ static int ar933x_uart_startup(struct uart_port *port)
/* Enable RX interrupts */
ar933x_uart_start_rx_interrupt(up);
- spin_unlock_irqrestore(&up->port.lock, flags);
+ uart_port_unlock_irqrestore(&up->port, flags);
return 0;
}
@@ -632,9 +632,9 @@ static void ar933x_uart_console_write(struct console *co, const char *s,
if (up->port.sysrq)
locked = 0;
else if (oops_in_progress)
- locked = spin_trylock(&up->port.lock);
+ locked = uart_port_trylock(&up->port);
else
- spin_lock(&up->port.lock);
+ uart_port_lock(&up->port);
/*
* First save the IER then disable the interrupts
@@ -654,7 +654,7 @@ static void ar933x_uart_console_write(struct console *co, const char *s,
ar933x_uart_write(up, AR933X_UART_INT_REG, AR933X_UART_INT_ALLINTS);
if (locked)
- spin_unlock(&up->port.lock);
+ uart_port_unlock(&up->port);
local_irq_restore(flags);
}
--
2.39.2