Utilize the integrated 10-bit ADC in Max5970/Max5978 to enable voltage
and current monitoring. This feature is seamlessly integrated through
the hwmon subsystem.
Signed-off-by: Naresh Solanki <[email protected]>
---
Changes in V4:
- Use IS_REACHABLE
- Use rdevs array for hwmon ops.
- Remove duplicate i2c_set_clientdata
Changes in V3:
- Update signed-off
- Add break
- Update hwmon dev register name to max5970
- Remove changes in Kconfig.
Changes in V2:
- default case added for switch statement
- Add dependency on HWMON
---
drivers/regulator/max5970-regulator.c | 138 +++++++++++++++++++++++++-
1 file changed, 136 insertions(+), 2 deletions(-)
diff --git a/drivers/regulator/max5970-regulator.c b/drivers/regulator/max5970-regulator.c
index b56a174cde3d..06168fe1dadd 100644
--- a/drivers/regulator/max5970-regulator.c
+++ b/drivers/regulator/max5970-regulator.c
@@ -10,6 +10,7 @@
#include <linux/bitops.h>
#include <linux/device.h>
#include <linux/err.h>
+#include <linux/hwmon.h>
#include <linux/module.h>
#include <linux/io.h>
#include <linux/of.h>
@@ -32,6 +33,128 @@ enum max597x_regulator_id {
MAX597X_SW1,
};
+static int max5970_read_adc(struct regmap *regmap, int reg, long *val)
+{
+ u8 reg_data[2];
+ int ret;
+
+ ret = regmap_bulk_read(regmap, reg, ®_data[0], 2);
+ if (ret < 0)
+ return ret;
+
+ *val = (reg_data[0] << 2) | (reg_data[1] & 3);
+
+ return 0;
+}
+
+static int max5970_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ struct regulator_dev **rdevs = dev_get_drvdata(dev);
+ struct max5970_regulator *ddata = rdev_get_drvdata(rdevs[channel]);
+ struct regmap *regmap = ddata->regmap;
+ int ret;
+
+ switch (type) {
+ case hwmon_curr:
+ switch (attr) {
+ case hwmon_curr_input:
+ ret = max5970_read_adc(regmap, MAX5970_REG_CURRENT_H(channel), val);
+ /*
+ * Calculate current from ADC value, IRNG range & shunt resistor value.
+ * ddata->irng holds the voltage corresponding to the maximum value the
+ * 10-bit ADC can measure.
+ * To obtain the output, multiply the ADC value by the IRNG range (in
+ * millivolts) and then divide it by the maximum value of the 10-bit ADC.
+ */
+ *val = (*val * ddata->irng) >> 10;
+ /* Convert the voltage meansurement across shunt resistor to current */
+ *val = (*val * 1000) / ddata->shunt_micro_ohms;
+ return ret;
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ case hwmon_in:
+ switch (attr) {
+ case hwmon_in_input:
+ ret = max5970_read_adc(regmap, MAX5970_REG_VOLTAGE_H(channel), val);
+ /*
+ * Calculate voltage from ADC value and MON range.
+ * ddata->mon_rng holds the voltage corresponding to the maximum value the
+ * 10-bit ADC can measure.
+ * To obtain the output, multiply the ADC value by the MON range (in
+ * microvolts) and then divide it by the maximum value of the 10-bit ADC.
+ */
+ *val = mul_u64_u32_shr(*val, ddata->mon_rng, 10);
+ /* uV to mV */
+ *val = *val / 1000;
+ return ret;
+ default:
+ return -EOPNOTSUPP;
+ }
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static umode_t max5970_is_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ struct regulator_dev **rdevs = (struct regulator_dev **)data;
+ struct max5970_regulator *ddata;
+
+ if (!rdevs || !rdevs[channel])
+ return 0;
+
+ ddata = rdev_get_drvdata(rdevs[channel]);
+
+ if (!ddata || channel >= ddata->num_switches)
+ return 0;
+
+ switch (type) {
+ case hwmon_in:
+ switch (attr) {
+ case hwmon_in_input:
+ return 0444;
+ default:
+ break;
+ }
+ break;
+ case hwmon_curr:
+ switch (attr) {
+ case hwmon_curr_input:
+ /* Current measurement requires knowledge of the shunt resistor value. */
+ if (ddata->shunt_micro_ohms)
+ return 0444;
+ break;
+ default:
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+ return 0;
+}
+
+static const struct hwmon_ops max5970_hwmon_ops = {
+ .is_visible = max5970_is_visible,
+ .read = max5970_read,
+};
+
+static const struct hwmon_channel_info *max5970_info[] = {
+ HWMON_CHANNEL_INFO(in, HWMON_I_INPUT, HWMON_I_INPUT),
+ HWMON_CHANNEL_INFO(curr, HWMON_C_INPUT, HWMON_C_INPUT),
+ NULL
+};
+
+static const struct hwmon_chip_info max5970_chip_info = {
+ .ops = &max5970_hwmon_ops,
+ .info = max5970_info,
+};
+
static int max597x_uvp_ovp_check_mode(struct regulator_dev *rdev, int severity)
{
int ret, reg;
@@ -431,7 +554,8 @@ static int max597x_regulator_probe(struct platform_device *pdev)
struct i2c_client *i2c = to_i2c_client(pdev->dev.parent);
struct regulator_config config = { };
struct regulator_dev *rdev;
- struct regulator_dev *rdevs[MAX5970_NUM_SWITCHES];
+ struct regulator_dev **rdevs = NULL;
+ struct device *hwmon_dev;
int num_switches;
int ret, i;
@@ -451,9 +575,10 @@ static int max597x_regulator_probe(struct platform_device *pdev)
else
return -ENODEV;
- i2c_set_clientdata(i2c, max597x);
num_switches = max597x->num_switches;
+ rdevs = devm_kcalloc(&i2c->dev, num_switches, sizeof(struct regulator_dev *), GFP_KERNEL);
+
for (i = 0; i < num_switches; i++) {
data =
devm_kzalloc(&i2c->dev, sizeof(struct max5970_regulator),
@@ -485,6 +610,15 @@ static int max597x_regulator_probe(struct platform_device *pdev)
max597x->shunt_micro_ohms[i] = data->shunt_micro_ohms;
}
+ if (IS_REACHABLE(CONFIG_HWMON)) {
+ hwmon_dev = devm_hwmon_device_register_with_info(&i2c->dev, "max5970", rdevs,
+ &max5970_chip_info, NULL);
+ if (IS_ERR(hwmon_dev)) {
+ return dev_err_probe(&i2c->dev, PTR_ERR(hwmon_dev),
+ "Unable to register hwmon device\n");
+ }
+ }
+
if (i2c->irq) {
ret =
max597x_setup_irq(&i2c->dev, i2c->irq, rdevs, num_switches,
base-commit: 41f02a383ac652f1a0b5538c5901b7ec93e37290
--
2.41.0
On Tue, Sep 19, 2023 at 07:48:23AM +0200, Naresh Solanki wrote:
> Utilize the integrated 10-bit ADC in Max5970/Max5978 to enable voltage
> and current monitoring. This feature is seamlessly integrated through
> the hwmon subsystem.
Guenter, are you OK with the hwmon side of this?
On Tue, Sep 19, 2023 at 07:48:23AM +0200, Naresh Solanki wrote:
> Utilize the integrated 10-bit ADC in Max5970/Max5978 to enable voltage
> and current monitoring. This feature is seamlessly integrated through
> the hwmon subsystem.
>
> Signed-off-by: Naresh Solanki <[email protected]>
> ---
> Changes in V4:
> - Use IS_REACHABLE
> - Use rdevs array for hwmon ops.
> - Remove duplicate i2c_set_clientdata
> Changes in V3:
> - Update signed-off
> - Add break
> - Update hwmon dev register name to max5970
> - Remove changes in Kconfig.
> Changes in V2:
> - default case added for switch statement
> - Add dependency on HWMON
> ---
> drivers/regulator/max5970-regulator.c | 138 +++++++++++++++++++++++++-
> 1 file changed, 136 insertions(+), 2 deletions(-)
>
>
> base-commit: 41f02a383ac652f1a0b5538c5901b7ec93e37290
>
> diff --git a/drivers/regulator/max5970-regulator.c b/drivers/regulator/max5970-regulator.c
> index b56a174cde3d..06168fe1dadd 100644
> --- a/drivers/regulator/max5970-regulator.c
> +++ b/drivers/regulator/max5970-regulator.c
> @@ -10,6 +10,7 @@
> #include <linux/bitops.h>
> #include <linux/device.h>
> #include <linux/err.h>
> +#include <linux/hwmon.h>
> #include <linux/module.h>
> #include <linux/io.h>
> #include <linux/of.h>
> @@ -32,6 +33,128 @@ enum max597x_regulator_id {
> MAX597X_SW1,
> };
>
> +static int max5970_read_adc(struct regmap *regmap, int reg, long *val)
> +{
> + u8 reg_data[2];
> + int ret;
> +
> + ret = regmap_bulk_read(regmap, reg, ®_data[0], 2);
> + if (ret < 0)
> + return ret;
> +
> + *val = (reg_data[0] << 2) | (reg_data[1] & 3);
> +
> + return 0;
> +}
> +
> +static int max5970_read(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long *val)
> +{
> + struct regulator_dev **rdevs = dev_get_drvdata(dev);
> + struct max5970_regulator *ddata = rdev_get_drvdata(rdevs[channel]);
> + struct regmap *regmap = ddata->regmap;
> + int ret;
> +
> + switch (type) {
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + ret = max5970_read_adc(regmap, MAX5970_REG_CURRENT_H(channel), val);
> + /*
> + * Calculate current from ADC value, IRNG range & shunt resistor value.
> + * ddata->irng holds the voltage corresponding to the maximum value the
> + * 10-bit ADC can measure.
> + * To obtain the output, multiply the ADC value by the IRNG range (in
> + * millivolts) and then divide it by the maximum value of the 10-bit ADC.
> + */
> + *val = (*val * ddata->irng) >> 10;
> + /* Convert the voltage meansurement across shunt resistor to current */
> + *val = (*val * 1000) / ddata->shunt_micro_ohms;
> + return ret;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + ret = max5970_read_adc(regmap, MAX5970_REG_VOLTAGE_H(channel), val);
> + /*
> + * Calculate voltage from ADC value and MON range.
> + * ddata->mon_rng holds the voltage corresponding to the maximum value the
> + * 10-bit ADC can measure.
> + * To obtain the output, multiply the ADC value by the MON range (in
> + * microvolts) and then divide it by the maximum value of the 10-bit ADC.
> + */
> + *val = mul_u64_u32_shr(*val, ddata->mon_rng, 10);
> + /* uV to mV */
> + *val = *val / 1000;
> + return ret;
> + default:
> + return -EOPNOTSUPP;
> + }
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static umode_t max5970_is_visible(const void *data,
> + enum hwmon_sensor_types type,
> + u32 attr, int channel)
> +{
> + struct regulator_dev **rdevs = (struct regulator_dev **)data;
> + struct max5970_regulator *ddata;
> +
> + if (!rdevs || !rdevs[channel])
How can rdevs be NULL here ? Unless I am missing something, that can
only happen if its allocation in the probe function failed, but then
the system would long since have crashed before it gets here.
Also, rdevs[] only has as many entries as there are switches. That can
be 1 or 2. However, the hwmon subsystem will always assume that there are
two channels, because it is told so, and it will thus try to access rdevs[1]
even if only a single channel was allocated.
> + return 0;
> +
> + ddata = rdev_get_drvdata(rdevs[channel]);
With the above in mind, I wonder what that points to if channel == 1 and
ddata->num_switches == 1.
> +
> + if (!ddata || channel >= ddata->num_switches)
> + return 0;
> +
> + switch (type) {
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + return 0444;
> + default:
> + break;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + /* Current measurement requires knowledge of the shunt resistor value. */
> + if (ddata->shunt_micro_ohms)
> + return 0444;
> + break;
> + default:
> + break;
> + }
> + break;
> + default:
> + break;
> + }
> + return 0;
> +}
> +
> +static const struct hwmon_ops max5970_hwmon_ops = {
> + .is_visible = max5970_is_visible,
> + .read = max5970_read,
> +};
> +
> +static const struct hwmon_channel_info *max5970_info[] = {
> + HWMON_CHANNEL_INFO(in, HWMON_I_INPUT, HWMON_I_INPUT),
> + HWMON_CHANNEL_INFO(curr, HWMON_C_INPUT, HWMON_C_INPUT),
> + NULL
> +};
> +
> +static const struct hwmon_chip_info max5970_chip_info = {
> + .ops = &max5970_hwmon_ops,
> + .info = max5970_info,
> +};
> +
> static int max597x_uvp_ovp_check_mode(struct regulator_dev *rdev, int severity)
> {
> int ret, reg;
> @@ -431,7 +554,8 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> struct i2c_client *i2c = to_i2c_client(pdev->dev.parent);
> struct regulator_config config = { };
> struct regulator_dev *rdev;
> - struct regulator_dev *rdevs[MAX5970_NUM_SWITCHES];
> + struct regulator_dev **rdevs = NULL;
> + struct device *hwmon_dev;
> int num_switches;
> int ret, i;
>
> @@ -451,9 +575,10 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> else
> return -ENODEV;
>
> - i2c_set_clientdata(i2c, max597x);
> num_switches = max597x->num_switches;
>
> + rdevs = devm_kcalloc(&i2c->dev, num_switches, sizeof(struct regulator_dev *), GFP_KERNEL);
> +
What if devm_kcalloc() returns NULL ?
> for (i = 0; i < num_switches; i++) {
> data =
> devm_kzalloc(&i2c->dev, sizeof(struct max5970_regulator),
> @@ -485,6 +610,15 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> max597x->shunt_micro_ohms[i] = data->shunt_micro_ohms;
> }
>
> + if (IS_REACHABLE(CONFIG_HWMON)) {
> + hwmon_dev = devm_hwmon_device_register_with_info(&i2c->dev, "max5970", rdevs,
> + &max5970_chip_info, NULL);
> + if (IS_ERR(hwmon_dev)) {
> + return dev_err_probe(&i2c->dev, PTR_ERR(hwmon_dev),
> + "Unable to register hwmon device\n");
> + }
> + }
> +
> if (i2c->irq) {
> ret =
> max597x_setup_irq(&i2c->dev, i2c->irq, rdevs, num_switches,
On Tue, Sep 26, 2023 at 05:28:15PM +0200, Mark Brown wrote:
> On Tue, Sep 19, 2023 at 07:48:23AM +0200, Naresh Solanki wrote:
> > Utilize the integrated 10-bit ADC in Max5970/Max5978 to enable voltage
> > and current monitoring. This feature is seamlessly integrated through
> > the hwmon subsystem.
>
> Guenter, are you OK with the hwmon side of this?
Sorry, I lost track. Not really; see my response to the patch.
I think the memory allocation in that driver is a bit too complicated.
It trades simplicity for minor memory savings, and even those savings
are questionable. It would have been much easier and simpler to just
add a two-element regulator_dev array to struct max5970_regulator
and live with the "lost" memory if only one of them is used. I suspect
that would have consumed less memory and code overall.
Guenter
Hi Guenter,
On Wed, 27 Sept 2023 at 01:06, Guenter Roeck <[email protected]> wrote:
>
> On Tue, Sep 19, 2023 at 07:48:23AM +0200, Naresh Solanki wrote:
> > Utilize the integrated 10-bit ADC in Max5970/Max5978 to enable voltage
> > and current monitoring. This feature is seamlessly integrated through
> > the hwmon subsystem.
> >
> > Signed-off-by: Naresh Solanki <[email protected]>
> > ---
> > Changes in V4:
> > - Use IS_REACHABLE
> > - Use rdevs array for hwmon ops.
> > - Remove duplicate i2c_set_clientdata
> > Changes in V3:
> > - Update signed-off
> > - Add break
> > - Update hwmon dev register name to max5970
> > - Remove changes in Kconfig.
> > Changes in V2:
> > - default case added for switch statement
> > - Add dependency on HWMON
> > ---
> > drivers/regulator/max5970-regulator.c | 138 +++++++++++++++++++++++++-
> > 1 file changed, 136 insertions(+), 2 deletions(-)
> >
> >
> > base-commit: 41f02a383ac652f1a0b5538c5901b7ec93e37290
> >
> > diff --git a/drivers/regulator/max5970-regulator.c b/drivers/regulator/max5970-regulator.c
> > index b56a174cde3d..06168fe1dadd 100644
> > --- a/drivers/regulator/max5970-regulator.c
> > +++ b/drivers/regulator/max5970-regulator.c
> > @@ -10,6 +10,7 @@
> > #include <linux/bitops.h>
> > #include <linux/device.h>
> > #include <linux/err.h>
> > +#include <linux/hwmon.h>
> > #include <linux/module.h>
> > #include <linux/io.h>
> > #include <linux/of.h>
> > @@ -32,6 +33,128 @@ enum max597x_regulator_id {
> > MAX597X_SW1,
> > };
> >
> > +static int max5970_read_adc(struct regmap *regmap, int reg, long *val)
> > +{
> > + u8 reg_data[2];
> > + int ret;
> > +
> > + ret = regmap_bulk_read(regmap, reg, ®_data[0], 2);
> > + if (ret < 0)
> > + return ret;
> > +
> > + *val = (reg_data[0] << 2) | (reg_data[1] & 3);
> > +
> > + return 0;
> > +}
> > +
> > +static int max5970_read(struct device *dev, enum hwmon_sensor_types type,
> > + u32 attr, int channel, long *val)
> > +{
> > + struct regulator_dev **rdevs = dev_get_drvdata(dev);
> > + struct max5970_regulator *ddata = rdev_get_drvdata(rdevs[channel]);
> > + struct regmap *regmap = ddata->regmap;
> > + int ret;
> > +
> > + switch (type) {
> > + case hwmon_curr:
> > + switch (attr) {
> > + case hwmon_curr_input:
> > + ret = max5970_read_adc(regmap, MAX5970_REG_CURRENT_H(channel), val);
> > + /*
> > + * Calculate current from ADC value, IRNG range & shunt resistor value.
> > + * ddata->irng holds the voltage corresponding to the maximum value the
> > + * 10-bit ADC can measure.
> > + * To obtain the output, multiply the ADC value by the IRNG range (in
> > + * millivolts) and then divide it by the maximum value of the 10-bit ADC.
> > + */
> > + *val = (*val * ddata->irng) >> 10;
> > + /* Convert the voltage meansurement across shunt resistor to current */
> > + *val = (*val * 1000) / ddata->shunt_micro_ohms;
> > + return ret;
> > + default:
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + case hwmon_in:
> > + switch (attr) {
> > + case hwmon_in_input:
> > + ret = max5970_read_adc(regmap, MAX5970_REG_VOLTAGE_H(channel), val);
> > + /*
> > + * Calculate voltage from ADC value and MON range.
> > + * ddata->mon_rng holds the voltage corresponding to the maximum value the
> > + * 10-bit ADC can measure.
> > + * To obtain the output, multiply the ADC value by the MON range (in
> > + * microvolts) and then divide it by the maximum value of the 10-bit ADC.
> > + */
> > + *val = mul_u64_u32_shr(*val, ddata->mon_rng, 10);
> > + /* uV to mV */
> > + *val = *val / 1000;
> > + return ret;
> > + default:
> > + return -EOPNOTSUPP;
> > + }
> > + default:
> > + return -EOPNOTSUPP;
> > + }
> > +}
> > +
> > +static umode_t max5970_is_visible(const void *data,
> > + enum hwmon_sensor_types type,
> > + u32 attr, int channel)
> > +{
> > + struct regulator_dev **rdevs = (struct regulator_dev **)data;
> > + struct max5970_regulator *ddata;
> > +
> > + if (!rdevs || !rdevs[channel])
>
> How can rdevs be NULL here ? Unless I am missing something, that can
> only happen if its allocation in the probe function failed, but then
> the system would long since have crashed before it gets here.
>
> Also, rdevs[] only has as many entries as there are switches. That can
> be 1 or 2. However, the hwmon subsystem will always assume that there are
> two channels, because it is told so, and it will thus try to access rdevs[1]
> even if only a single channel was allocated.
Yes. Will update to:
if (!rdevs[channel])
return 0;
Also will simplify memory allocation to have two element array.
>
> > + return 0;
> > +
> > + ddata = rdev_get_drvdata(rdevs[channel]);
>
> With the above in mind, I wonder what that points to if channel == 1 and
> ddata->num_switches == 1.
This can be avoided with memory allocation simplification & previous
if condition check.
>
> > +
> > + if (!ddata || channel >= ddata->num_switches)
> > + return 0;
> > +
> > + switch (type) {
> > + case hwmon_in:
> > + switch (attr) {
> > + case hwmon_in_input:
> > + return 0444;
> > + default:
> > + break;
> > + }
> > + break;
> > + case hwmon_curr:
> > + switch (attr) {
> > + case hwmon_curr_input:
> > + /* Current measurement requires knowledge of the shunt resistor value. */
> > + if (ddata->shunt_micro_ohms)
> > + return 0444;
> > + break;
> > + default:
> > + break;
> > + }
> > + break;
> > + default:
> > + break;
> > + }
> > + return 0;
> > +}
> > +
> > +static const struct hwmon_ops max5970_hwmon_ops = {
> > + .is_visible = max5970_is_visible,
> > + .read = max5970_read,
> > +};
> > +
> > +static const struct hwmon_channel_info *max5970_info[] = {
> > + HWMON_CHANNEL_INFO(in, HWMON_I_INPUT, HWMON_I_INPUT),
> > + HWMON_CHANNEL_INFO(curr, HWMON_C_INPUT, HWMON_C_INPUT),
> > + NULL
> > +};
> > +
> > +static const struct hwmon_chip_info max5970_chip_info = {
> > + .ops = &max5970_hwmon_ops,
> > + .info = max5970_info,
> > +};
> > +
> > static int max597x_uvp_ovp_check_mode(struct regulator_dev *rdev, int severity)
> > {
> > int ret, reg;
> > @@ -431,7 +554,8 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> > struct i2c_client *i2c = to_i2c_client(pdev->dev.parent);
> > struct regulator_config config = { };
> > struct regulator_dev *rdev;
> > - struct regulator_dev *rdevs[MAX5970_NUM_SWITCHES];
> > + struct regulator_dev **rdevs = NULL;
> > + struct device *hwmon_dev;
> > int num_switches;
> > int ret, i;
> >
> > @@ -451,9 +575,10 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> > else
> > return -ENODEV;
> >
> > - i2c_set_clientdata(i2c, max597x);
> > num_switches = max597x->num_switches;
> >
> > + rdevs = devm_kcalloc(&i2c->dev, num_switches, sizeof(struct regulator_dev *), GFP_KERNEL);
> > +
>
> What if devm_kcalloc() returns NULL ?
Will add error checking here.
>
> > for (i = 0; i < num_switches; i++) {
> > data =
> > devm_kzalloc(&i2c->dev, sizeof(struct max5970_regulator),
> > @@ -485,6 +610,15 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> > max597x->shunt_micro_ohms[i] = data->shunt_micro_ohms;
> > }
> >
> > + if (IS_REACHABLE(CONFIG_HWMON)) {
> > + hwmon_dev = devm_hwmon_device_register_with_info(&i2c->dev, "max5970", rdevs,
> > + &max5970_chip_info, NULL);
> > + if (IS_ERR(hwmon_dev)) {
> > + return dev_err_probe(&i2c->dev, PTR_ERR(hwmon_dev),
> > + "Unable to register hwmon device\n");
> > + }
> > + }
> > +
> > if (i2c->irq) {
> > ret =
> > max597x_setup_irq(&i2c->dev, i2c->irq, rdevs, num_switches,
Regards,
Naresh