From: Martin Tůma <[email protected]>
Hi,
This patch adds a driver for the Digiteq Automotive MGB4 grabber card.
MGB4 is a modular frame grabber PCIe card for automotive video interfaces
(FPD-Link and GMSL for now). It is based on a Xilinx FPGA and uses their
XDMA IP core for DMA transfers. Additionally, Xilinx I2C and SPI IP cores
which already have drivers in linux are used in the design.
The driver is a quite standard v4l2 driver, with one exception - there are
a lot of sysfs options that may/must be set before opening the v4l2 device
to adapt the card on a specific signal (see mgb4.rst for details)
as the card must be able to work with various signal sources (or displays)
that can not be auto-detected.
Changes in v10:
* Use propper locks/is_busy functions when accessing the video devices in
the sysfs callbacks.
* Fixed issues found by the sparse/smatch tools.
Changes in v9:
* Renamed all sysfs show/store functions using the propper naming convention.
* Now using device_add_groups() when initializing the sysfs properties.
* Fixed build without debugfs support.
* Fixed documentation (vsync/hsync) + added default values where applicable.
* Fixed the rest of minor issues from v8 review.
Changes in v8:
* Fixed broken video buffer size computation.
* Fixed switched I2C deserializers addresses.
* Do not depend on hwmon.
Changes in v7:
* Now using hwmon for FPGA temperature reporting.
* Now using VIDIOC_S_FMT and v4l2_pix_format.bytesperline for setting
the alignment.
* Removed the magic sleep when loading the i2c/spi adapter modules (solved by
request_module() calls with propper - "platform:" prefixed - module
names).
* Now properly reporting all the timings info in the VIDIOC_G_DV_TIMINGS
ioctls.
* Updated the documentation.
* Minor fixes as discussed in the v6 review.
* Added debugfs access to the FPGA registers.
Changes in v6:
* Rebased to current master that includes the Xilinx XDMA driver.
Changes in v5:
* Removed unused <linux/version.h> includes
Changes in v4:
* Redesigned the signal change handling logic. Now using the propper timings
API in the video input driver and a propper open() syscall check/logic in
the video output driver.
* Fixed all minor issues from v3 review.
* 'checkpatch.pl --strict' used for checking the code.
Changes in v3:
* Rebased the DMA transfers part to use the new XDMA driver from Xilinx/AMD
Changes in v2:
* Completely rewritten the original Xilinx's XDMA driver to meet kernel code
standards.
* Added all required "to" and "cc" mail addresses.
===== v4l2-compliance results - input =====
v4l2-compliance 1.24.1, 64 bits, 64-bit time_t
Compliance test for mgb4 device /dev/video0:
Driver Info:
Driver name : mgb4
Card type : MGB4 PCIe Card
Bus info : PCI:0000:01:00.0
Driver version : 6.4.0
Capabilities : 0x85200001
Video Capture
Read/Write
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x05200001
Video Capture
Read/Write
Streaming
Extended Pix Format
Required ioctls:
test VIDIOC_QUERYCAP: OK
test invalid ioctls: OK
Allow for multiple opens:
test second /dev/video0 open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK
Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK (Not Supported)
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 1 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK
test VIDIOC_DV_TIMINGS_CAP: OK
test VIDIOC_G/S_EDID: OK (Not Supported)
Control ioctls (Input 0):
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK (Not Supported)
test VIDIOC_QUERYCTRL: OK (Not Supported)
test VIDIOC_G/S_CTRL: OK (Not Supported)
test VIDIOC_G/S/TRY_EXT_CTRLS: OK (Not Supported)
warn: v4l2-test-controls.cpp(1139): V4L2_CID_DV_RX_POWER_PRESENT not found for input 0
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported)
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 0 Private Controls: 0
Format ioctls (Input 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
test VIDIOC_G/S_PARM: OK
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)
Codec ioctls (Input 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls (Input 0):
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
test VIDIOC_EXPBUF: OK
test Requests: OK (Not Supported)
Total for mgb4 device /dev/video0: 45, Succeeded: 45, Failed: 0, Warnings: 1
===== v4l2-compliance results - output =====
v4l2-compliance 1.24.1, 64 bits, 64-bit time_t
Compliance test for mgb4 device /dev/video2:
Driver Info:
Driver name : mgb4
Card type : MGB4 PCIe Card
Bus info : PCI:0000:01:00.0
Driver version : 6.4.0
Capabilities : 0x85200002
Video Output
Read/Write
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x05200002
Video Output
Read/Write
Streaming
Extended Pix Format
Required ioctls:
test VIDIOC_QUERYCAP: OK
test invalid ioctls: OK
Allow for multiple opens:
test second /dev/video2 open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK
Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK (Not Supported)
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 0 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 1 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
test VIDIOC_G/S_EDID: OK (Not Supported)
Control ioctls (Output 0):
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK (Not Supported)
test VIDIOC_QUERYCTRL: OK (Not Supported)
test VIDIOC_G/S_CTRL: OK (Not Supported)
test VIDIOC_G/S/TRY_EXT_CTRLS: OK (Not Supported)
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported)
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 0 Private Controls: 0
Format ioctls (Output 0):
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK (Not Supported)
test Composing: OK (Not Supported)
test Scaling: OK (Not Supported)
Codec ioctls (Output 0):
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls (Output 0):
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
test VIDIOC_EXPBUF: OK
test Requests: OK (Not Supported)
Total for mgb4 device /dev/video2: 45, Succeeded: 45, Failed: 0, Warnings: 0
Martin Tůma (2):
Added Digiteq Automotive MGB4 driver
Added Digiteq Automotive MGB4 driver documentation
Documentation/admin-guide/media/mgb4.rst | 374 +++++++
.../admin-guide/media/pci-cardlist.rst | 1 +
.../admin-guide/media/v4l-drivers.rst | 1 +
MAINTAINERS | 7 +
drivers/media/pci/Kconfig | 1 +
drivers/media/pci/Makefile | 1 +
drivers/media/pci/mgb4/Kconfig | 17 +
drivers/media/pci/mgb4/Makefile | 6 +
drivers/media/pci/mgb4/mgb4_cmt.c | 244 +++++
drivers/media/pci/mgb4/mgb4_cmt.h | 17 +
drivers/media/pci/mgb4/mgb4_core.c | 686 +++++++++++++
drivers/media/pci/mgb4/mgb4_core.h | 74 ++
drivers/media/pci/mgb4/mgb4_dma.c | 123 +++
drivers/media/pci/mgb4/mgb4_dma.h | 18 +
drivers/media/pci/mgb4/mgb4_i2c.c | 140 +++
drivers/media/pci/mgb4/mgb4_i2c.h | 35 +
drivers/media/pci/mgb4/mgb4_io.h | 33 +
drivers/media/pci/mgb4/mgb4_regs.c | 30 +
drivers/media/pci/mgb4/mgb4_regs.h | 35 +
drivers/media/pci/mgb4/mgb4_sysfs.h | 18 +
drivers/media/pci/mgb4/mgb4_sysfs_in.c | 744 ++++++++++++++
drivers/media/pci/mgb4/mgb4_sysfs_out.c | 681 +++++++++++++
drivers/media/pci/mgb4/mgb4_sysfs_pci.c | 71 ++
drivers/media/pci/mgb4/mgb4_trigger.c | 208 ++++
drivers/media/pci/mgb4/mgb4_trigger.h | 8 +
drivers/media/pci/mgb4/mgb4_vin.c | 934 ++++++++++++++++++
drivers/media/pci/mgb4/mgb4_vin.h | 69 ++
drivers/media/pci/mgb4/mgb4_vout.c | 597 +++++++++++
drivers/media/pci/mgb4/mgb4_vout.h | 65 ++
29 files changed, 5238 insertions(+)
create mode 100644 Documentation/admin-guide/media/mgb4.rst
create mode 100644 drivers/media/pci/mgb4/Kconfig
create mode 100644 drivers/media/pci/mgb4/Makefile
create mode 100644 drivers/media/pci/mgb4/mgb4_cmt.c
create mode 100644 drivers/media/pci/mgb4/mgb4_cmt.h
create mode 100644 drivers/media/pci/mgb4/mgb4_core.c
create mode 100644 drivers/media/pci/mgb4/mgb4_core.h
create mode 100644 drivers/media/pci/mgb4/mgb4_dma.c
create mode 100644 drivers/media/pci/mgb4/mgb4_dma.h
create mode 100644 drivers/media/pci/mgb4/mgb4_i2c.c
create mode 100644 drivers/media/pci/mgb4/mgb4_i2c.h
create mode 100644 drivers/media/pci/mgb4/mgb4_io.h
create mode 100644 drivers/media/pci/mgb4/mgb4_regs.c
create mode 100644 drivers/media/pci/mgb4/mgb4_regs.h
create mode 100644 drivers/media/pci/mgb4/mgb4_sysfs.h
create mode 100644 drivers/media/pci/mgb4/mgb4_sysfs_in.c
create mode 100644 drivers/media/pci/mgb4/mgb4_sysfs_out.c
create mode 100644 drivers/media/pci/mgb4/mgb4_sysfs_pci.c
create mode 100644 drivers/media/pci/mgb4/mgb4_trigger.c
create mode 100644 drivers/media/pci/mgb4/mgb4_trigger.h
create mode 100644 drivers/media/pci/mgb4/mgb4_vin.c
create mode 100644 drivers/media/pci/mgb4/mgb4_vin.h
create mode 100644 drivers/media/pci/mgb4/mgb4_vout.c
create mode 100644 drivers/media/pci/mgb4/mgb4_vout.h
base-commit: ce9ecca0238b140b88f43859b211c9fdfd8e5b70
--
2.40.1
From: Martin Tůma <[email protected]>
The "admin-guide" documentation for the Digiteq Automotive MGB4 driver.
Signed-off-by: Martin Tůma <[email protected]>
---
Documentation/admin-guide/media/mgb4.rst | 374 ++++++++++++++++++
.../admin-guide/media/pci-cardlist.rst | 1 +
.../admin-guide/media/v4l-drivers.rst | 1 +
3 files changed, 376 insertions(+)
create mode 100644 Documentation/admin-guide/media/mgb4.rst
diff --git a/Documentation/admin-guide/media/mgb4.rst b/Documentation/admin-guide/media/mgb4.rst
new file mode 100644
index 000000000000..2977f74d7e26
--- /dev/null
+++ b/Documentation/admin-guide/media/mgb4.rst
@@ -0,0 +1,374 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================
+mgb4 sysfs interface
+====================
+
+The mgb4 driver provides a sysfs interface, that is used to configure video
+stream related parameters (some of them must be set properly before the v4l2
+device can be opened) and obtain the video device/stream status.
+
+There are two types of parameters - global / PCI card related, found under
+``/sys/class/video4linux/videoX/device`` and module specific found under
+``/sys/class/video4linux/videoX``.
+
+
+Global (PCI card) parameters
+============================
+
+**module_type** (R):
+ Module type.
+
+ | 0 - No module present
+ | 1 - FPDL3
+ | 2 - GMSL
+
+**module_version** (R):
+ Module version number. Zero in case of a missing module.
+
+**fw_type** (R):
+ Firmware type.
+
+ | 1 - FPDL3
+ | 2 - GMSL
+
+**fw_version** (R):
+ Firmware version number.
+
+**serial_number** (R):
+ Card serial number. The format is::
+
+ PRODUCT-REVISION-SERIES-SERIAL
+
+ where each component is a 8b number.
+
+
+Common FPDL3/GMSL input parameters
+==================================
+
+**input_id** (R):
+ Input number ID, zero based.
+
+**oldi_lane_width** (RW):
+ Number of deserializer output lanes.
+
+ | 0 - single
+ | 1 - dual (default)
+
+**color_mapping** (RW):
+ Mapping of the incoming bits in the signal to the colour bits of the pixels.
+
+ | 0 - OLDI/JEIDA
+ | 1 - SPWG/VESA (default)
+
+**link_status** (R):
+ Video link status. If the link is locked, chips are properly connected and
+ communicating at the same speed and protocol. The link can be locked without
+ an active video stream.
+
+ A value of 0 is equivalent to the V4L2_IN_ST_NO_SYNC flag of the V4L2
+ VIDIOC_ENUMINPUT status bits.
+
+ | 0 - unlocked
+ | 1 - locked
+
+**stream_status** (R):
+ Video stream status. A stream is detected if the link is locked, the input
+ pixel clock is running and the DE signal is moving.
+
+ A value of 0 is equivalent to the V4L2_IN_ST_NO_SIGNAL flag of the V4L2
+ VIDIOC_ENUMINPUT status bits.
+
+ | 0 - not detected
+ | 1 - detected
+
+**video_width** (R):
+ Video stream width. This is the actual width as detected by the HW.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in the width
+ field of the v4l2_bt_timings struct.
+
+**video_height** (R):
+ Video stream height. This is the actual height as detected by the HW.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in the height
+ field of the v4l2_bt_timings struct.
+
+**vsync_status** (R):
+ The type of VSYNC pulses as detected by the video format detector.
+
+ The value is equivalent to the flags returned by VIDIOC_QUERY_DV_TIMINGS in
+ the polarities field of the v4l2_bt_timings struct.
+
+ | 0 - active low
+ | 1 - active high
+ | 2 - not available
+
+**hsync_status** (R):
+ The type of HSYNC pulses as detected by the video format detector.
+
+ The value is equivalent to the flags returned by VIDIOC_QUERY_DV_TIMINGS in
+ the polarities field of the v4l2_bt_timings struct.
+
+ | 0 - active low
+ | 1 - active high
+ | 2 - not available
+
+**vsync_gap_length** (RW):
+ If the incoming video signal does not contain synchronization VSYNC and
+ HSYNC pulses, these must be generated internally in the FPGA to achieve
+ the correct frame ordering. This value indicates, how many "empty" pixels
+ (pixels with deasserted Data Enable signal) are necessary to generate the
+ internal VSYNC pulse.
+
+**hsync_gap_length** (RW):
+ If the incoming video signal does not contain synchronization VSYNC and
+ HSYNC pulses, these must be generated internally in the FPGA to achieve
+ the correct frame ordering. This value indicates, how many "empty" pixels
+ (pixels with deasserted Data Enable signal) are necessary to generate the
+ internal HSYNC pulse. The value must be greater than 1 and smaller than
+ vsync_gap_length.
+
+**pclk_frequency** (R):
+ Input pixel clock frequency in kHz.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the pixelclock field of the v4l2_bt_timings struct.
+
+ *Note: The frequency_range parameter must be set properly first to get
+ a valid frequency here.*
+
+**hsync_width** (R):
+ Width of the HSYNC signal in PCLK clock ticks.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the hsync field of the v4l2_bt_timings struct.
+
+**vsync_width** (R):
+ Width of the VSYNC signal in PCLK clock ticks.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the vsync field of the v4l2_bt_timings struct.
+
+**hback_porch** (R):
+ Number of PCLK pulses between deassertion of the HSYNC signal and the first
+ valid pixel in the video line (marked by DE=1).
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the hbackporch field of the v4l2_bt_timings struct.
+
+**hfront_porch** (R):
+ Number of PCLK pulses between the end of the last valid pixel in the video
+ line (marked by DE=1) and assertion of the HSYNC signal.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the hfrontporch field of the v4l2_bt_timings struct.
+
+**vback_porch** (R):
+ Number of video lines between deassertion of the VSYNC signal and the video
+ line with the first valid pixel (marked by DE=1).
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the vbackporch field of the v4l2_bt_timings struct.
+
+**vfront_porch** (R):
+ Number of video lines between the end of the last valid pixel line (marked
+ by DE=1) and assertion of the VSYNC signal.
+
+ The value is identical to what VIDIOC_QUERY_DV_TIMINGS returns in
+ the vfrontporch field of the v4l2_bt_timings struct.
+
+**frequency_range** (RW)
+ PLL frequency range of the OLDI input clock generator. The PLL frequency is
+ derived from the Pixel Clock Frequency (PCLK) and is equal to PCLK if
+ oldi_lane_width is set to "single" and PCLK/2 if oldi_lane_width is set to
+ "dual".
+
+ | 0 - PLL < 50MHz (default)
+ | 1 - PLL >= 50MHz
+
+ *Note: This parameter can not be changed while the input v4l2 device is
+ open.*
+
+
+Common FPDL3/GMSL output parameters
+===================================
+
+**output_id** (R):
+ Output number ID, zero based.
+
+**video_source** (RW):
+ Output video source. If set to 0 or 1, the source is the corresponding card
+ input and the v4l2 output devices are disabled. If set to 2 or 3, the source
+ is the corresponding v4l2 video output device. The default is
+ the corresponding v4l2 output, i.e. 2 for OUT1 and 3 for OUT2.
+
+ | 0 - input 0
+ | 1 - input 1
+ | 2 - v4l2 output 0
+ | 3 - v4l2 output 1
+
+ *Note: This parameter can not be changed while ANY of the input/output v4l2
+ devices is open.*
+
+**display_width** (RW):
+ Display width. There is no autodetection of the connected display, so the
+ proper value must be set before the start of streaming. The default width
+ is 1280.
+
+ *Note: This parameter can not be changed while the output v4l2 device is
+ open.*
+
+**display_height** (RW):
+ Display height. There is no autodetection of the connected display, so the
+ proper value must be set before the start of streaming. The default height
+ is 640.
+
+ *Note: This parameter can not be changed while the output v4l2 device is
+ open.*
+
+**frame_rate** (RW):
+ Output video frame rate in frames per second. The default frame rate is
+ 60Hz.
+
+**hsync_polarity** (RW):
+ HSYNC signal polarity.
+
+ | 0 - active low (default)
+ | 1 - active high
+
+**vsync_polarity** (RW):
+ VSYNC signal polarity.
+
+ | 0 - active low (default)
+ | 1 - active high
+
+**de_polarity** (RW):
+ DE signal polarity.
+
+ | 0 - active low
+ | 1 - active high (default)
+
+**pclk_frequency** (RW):
+ Output pixel clock frequency. Allowed values are between 25000-190000(kHz)
+ and there is a non-linear stepping between two consecutive allowed
+ frequencies. The driver finds the nearest allowed frequency to the given
+ value and sets it. When reading this property, you get the exact
+ frequency set by the driver. The default frequency is 70000kHz.
+
+ *Note: This parameter can not be changed while the output v4l2 device is
+ open.*
+
+**hsync_width** (RW):
+ Width of the HSYNC signal in pixels. The default value is 16.
+
+**vsync_width** (RW):
+ Width of the VSYNC signal in video lines. The default value is 2.
+
+**hback_porch** (RW):
+ Number of PCLK pulses between deassertion of the HSYNC signal and the first
+ valid pixel in the video line (marked by DE=1). The default value is 32.
+
+**hfront_porch** (RW):
+ Number of PCLK pulses between the end of the last valid pixel in the video
+ line (marked by DE=1) and assertion of the HSYNC signal. The default value
+ is 32.
+
+**vback_porch** (RW):
+ Number of video lines between deassertion of the VSYNC signal and the video
+ line with the first valid pixel (marked by DE=1). The default value is 2.
+
+**vfront_porch** (RW):
+ Number of video lines between the end of the last valid pixel line (marked
+ by DE=1) and assertion of the VSYNC signal. The default value is 2.
+
+
+FPDL3 specific input parameters
+===============================
+
+**fpdl3_input_width** (RW):
+ Number of deserializer input lines.
+
+ | 0 - auto (default)
+ | 1 - single
+ | 2 - dual
+
+FPDL3 specific output parameters
+================================
+
+**fpdl3_output_width** (RW):
+ Number of serializer output lines.
+
+ | 0 - auto (default)
+ | 1 - single
+ | 2 - dual
+
+GMSL specific input parameters
+==============================
+
+**gmsl_mode** (RW):
+ GMSL speed mode.
+
+ | 0 - 12Gb/s (default)
+ | 1 - 6Gb/s
+ | 2 - 3Gb/s
+ | 3 - 1.5Gb/s
+
+**gmsl_stream_id** (RW):
+ The GMSL multi-stream contains up to four video streams. This parameter
+ selects which stream is captured by the video input. The value is the
+ zero-based index of the stream. The default stream id is 0.
+
+ *Note: This parameter can not be changed while the input v4l2 device is
+ open.*
+
+**gmsl_fec** (RW):
+ GMSL Forward Error Correction (FEC).
+
+ | 0 - disabled
+ | 1 - enabled (default)
+
+
+====================
+mgb4 mtd partitions
+====================
+
+The mgb4 driver creates a MTD device with two partitions:
+ - mgb4-fw.X - FPGA firmware.
+ - mgb4-data.X - Factory settings, e.g. card serial number.
+
+The *mgb4-fw* partition is writable and is used for FW updates, *mgb4-data* is
+read-only. The *X* attached to the partition name represents the card number.
+Depending on the CONFIG_MTD_PARTITIONED_MASTER kernel configuration, you may
+also have a third partition named *mgb4-flash* available in the system. This
+partition represents the whole, unpartitioned, card's FLASH memory and one should
+not fiddle with it...
+
+====================
+mgb4 iio (triggers)
+====================
+
+The mgb4 driver creates an Industrial I/O (IIO) device that provides trigger and
+signal level status capability. The following scan elements are available:
+
+**activity**:
+ The trigger levels and pending status.
+
+ | bit 1 - trigger 1 pending
+ | bit 2 - trigger 2 pending
+ | bit 5 - trigger 1 level
+ | bit 6 - trigger 2 level
+
+**timestamp**:
+ The trigger event timestamp.
+
+The iio device can operate either in "raw" mode where you can fetch the signal
+levels (activity bits 5 and 6) using sysfs access or in triggered buffer mode.
+In the triggered buffer mode you can follow the signal level changes (activity
+bits 1 and 2) using the iio device in /dev. If you enable the timestamps, you
+will also get the exact trigger event time that can be matched to a video frame
+(every mgb4 video frame has a timestamp with the same clock source).
+
+*Note: although the activity sample always contains all the status bits, it makes
+no sense to get the pending bits in raw mode or the level bits in the triggered
+buffer mode - the values do not represent valid data in such case.*
diff --git a/Documentation/admin-guide/media/pci-cardlist.rst b/Documentation/admin-guide/media/pci-cardlist.rst
index 42528795d4da..7d8e3c8987db 100644
--- a/Documentation/admin-guide/media/pci-cardlist.rst
+++ b/Documentation/admin-guide/media/pci-cardlist.rst
@@ -77,6 +77,7 @@ ipu3-cio2 Intel ipu3-cio2 driver
ivtv Conexant cx23416/cx23415 MPEG encoder/decoder
ivtvfb Conexant cx23415 framebuffer
mantis MANTIS based cards
+mgb4 Digiteq Automotive MGB4 frame grabber
mxb Siemens-Nixdorf 'Multimedia eXtension Board'
netup-unidvb NetUP Universal DVB card
ngene Micronas nGene
diff --git a/Documentation/admin-guide/media/v4l-drivers.rst b/Documentation/admin-guide/media/v4l-drivers.rst
index 1c41f87c3917..61283d67ceef 100644
--- a/Documentation/admin-guide/media/v4l-drivers.rst
+++ b/Documentation/admin-guide/media/v4l-drivers.rst
@@ -17,6 +17,7 @@ Video4Linux (V4L) driver-specific documentation
imx7
ipu3
ivtv
+ mgb4
omap3isp
omap4_camera
philips
--
2.40.1