Add INA233 binding documents for Yosemite V4 config.
Signed-off-by: Delphine CC Chiu <[email protected]>
---
.../devicetree/bindings/hwmon/ina233.txt | 27 +++++++++++++++++++
MAINTAINERS | 6 +++++
2 files changed, 33 insertions(+)
create mode 100644 Documentation/devicetree/bindings/hwmon/ina233.txt
diff --git a/Documentation/devicetree/bindings/hwmon/ina233.txt b/Documentation/devicetree/bindings/hwmon/ina233.txt
new file mode 100644
index 000000000000..a1067788ec0c
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ina233.txt
@@ -0,0 +1,27 @@
+Bindings for the Maxim MAX31790 Intelligent Fan Controller
+==========================================================
+
+Reference:
+
+https://pdf1.alldatasheet.com/datasheet-pdf/view/930928/TI1/INA233.html
+
+The INA233 device is a current, voltage and power monitor with an I2C-, SMBus-,and PMBus-compatible interface
+that is compliant with digital bus voltages from 1.8 V to 5.0 V.
+The device monitors and reports values for current, voltage and power.
+The integrated power accumulator can be used for energy or average power calculations.
+Programmable calibration value, conversion times and averaging when combined with an internal multiplier
+enable direct readouts of current in amperes and power in watts.
+
+Required properties:
+- compatible : ti,ina233
+- reg : I2C address
+- resistor-calibration : MFR_CALIBRATION which will be set into register 0xd4
+- current-lsb : Current_LSB for calibration
+Example:
+
+ ina233@45 {
+ compatible = "ti,ina233";
+ reg = <0x45>;
+ resistor-calibration = /bits/ 16 <0x0a00>;
+ current-lsb= /bits/ 16 <0x0001>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index bf0f54c24f81..48b9a73d259f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10243,6 +10243,12 @@ F: Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
F: Documentation/hwmon/ina209.rst
F: drivers/hwmon/ina209.c
+INA233 HARDWARE MONITOR DRIVER
+M: Delphine CC Chiu <[email protected]>
+S: Odd Fixes
+F: Documentation/devicetree/bindings/hwmon/ina233.txt
+F: drivers/hwmon/ina233.c
+
INA2XX HARDWARE MONITOR DRIVER
M: Guenter Roeck <[email protected]>
L: [email protected]
--
2.25.1
On 20/09/2023 07:47, Delphine CC Chiu wrote:
> Add INA233 binding documents for Yosemite V4 config.
>
> Signed-off-by: Delphine CC Chiu <[email protected]>
> ---
> .../devicetree/bindings/hwmon/ina233.txt | 27 +++++++++++++++++++
No bindings in the TXT format.
Anyway, this looks like could be merged with existing ina bindings.
Best regards,
Krzysztof
On 9/19/23 22:47, Delphine CC Chiu wrote:
> Add INA233 binding documents for Yosemite V4 config.
>
> Signed-off-by: Delphine CC Chiu <[email protected]>
> ---
> .../devicetree/bindings/hwmon/ina233.txt | 27 +++++++++++++++++++
> MAINTAINERS | 6 +++++
> 2 files changed, 33 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/hwmon/ina233.txt
>
> diff --git a/Documentation/devicetree/bindings/hwmon/ina233.txt b/Documentation/devicetree/bindings/hwmon/ina233.txt
> new file mode 100644
> index 000000000000..a1067788ec0c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/ina233.txt
> @@ -0,0 +1,27 @@
> +Bindings for the Maxim MAX31790 Intelligent Fan Controller
Not really.
> +==========================================================
> +
> +Reference:
> +
> +https://pdf1.alldatasheet.com/datasheet-pdf/view/930928/TI1/INA233.html
> +
> +The INA233 device is a current, voltage and power monitor with an I2C-, SMBus-,and PMBus-compatible interface
> +that is compliant with digital bus voltages from 1.8 V to 5.0 V.
> +The device monitors and reports values for current, voltage and power.
> +The integrated power accumulator can be used for energy or average power calculations.
> +Programmable calibration value, conversion times and averaging when combined with an internal multiplier
> +enable direct readouts of current in amperes and power in watts.
> +
> +Required properties:
> +- compatible : ti,ina233
> +- reg : I2C address
> +- resistor-calibration : MFR_CALIBRATION which will be set into register 0xd4
> +- current-lsb : Current_LSB for calibration
The lack of valid ranges is a concern for me, as well as the lack of units.
MFR_CALIBRATION is register 0xd4, so I don't think that "MFR_CALIBRATION
which will be set into register 0xd4" is a really useful description.
Also, the calibration register value is, per datasheet, supposed to be
calculated from current_lsb and Rshunt. Since current_lsb is calculated
from the maximum expected current, the properties should actually be
the maximum expected current and Rshunt.
> +Example:
> +
> + ina233@45 {
> + compatible = "ti,ina233";
> + reg = <0x45>;
> + resistor-calibration = /bits/ 16 <0x0a00>;
> + current-lsb= /bits/ 16 <0x0001>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index bf0f54c24f81..48b9a73d259f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -10243,6 +10243,12 @@ F: Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml
> F: Documentation/hwmon/ina209.rst
> F: drivers/hwmon/ina209.c
>
> +INA233 HARDWARE MONITOR DRIVER
> +M: Delphine CC Chiu <[email protected]>
> +S: Odd Fixes
> +F: Documentation/devicetree/bindings/hwmon/ina233.txt
> +F: drivers/hwmon/ina233.c
> +
> INA2XX HARDWARE MONITOR DRIVER
> M: Guenter Roeck <[email protected]>
> L: [email protected]