From: Alvin Šipraga <[email protected]>
For applications where the PLL must be adjusted without glitches in the
clock output(s), a new silabs,pll-reset-mode property is added. It
can be used to specify whether or not the PLL should be reset after
adjustment. Resetting is known to cause glitches.
For compatibility with older device trees, it must be assumed that the
default PLL reset mode is to unconditionally reset after adjustment.
Cc: Sebastian Hesselbarth <[email protected]>
Cc: Rabeeh Khoury <[email protected]>
Cc: Jacob Siverskog <[email protected]>
Cc: Sergej Sawazki <[email protected]>
Signed-off-by: Alvin Šipraga <[email protected]>
---
.../bindings/clock/silabs,si5351.yaml | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.yaml b/Documentation/devicetree/bindings/clock/silabs,si5351.yaml
index 3ca8d998c48c..b6692b323a66 100644
--- a/Documentation/devicetree/bindings/clock/silabs,si5351.yaml
+++ b/Documentation/devicetree/bindings/clock/silabs,si5351.yaml
@@ -50,6 +50,22 @@ properties:
Pair of <number source> for each PLL. Allows to overwrite clock source of
PLL A (number=0) or PLL B (number=1).
+ silabs,pll-reset-mode:
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ minItems: 1
+ maxItems: 2
+ description: |
+ Pair of <number mode> for each PLL. Configures the reset mode for PLL A
+ (number=0) and/or PLL B (number=1). Mode can be one of:
+
+ 0 - reset whenever PLL rate is adjusted (default mode)
+ 1 - do not reset when PLL rate is adjusted
+
+ In mode 1, the PLL is only reset if the silabs,pll-reset is specified in
+ one of the clock output child nodes that also sources the PLL. This mode
+ may be preferable if output clocks are expected to be adjusted without
+ glitches.
+
patternProperties:
"^clkout@?[0-8]$":
type: object
@@ -205,6 +221,9 @@ examples:
/* Use XTAL input as source of PLL0 and PLL1 */
silabs,pll-source = <0 0>, <1 0>;
+ /* Don't reset PLL1 on rate adjustment */
+ silabs,pll-reset-mode = <1 1>;
+
/*
* Overwrite CLK0 configuration with:
* - 8 mA output drive strength
--
2.41.0
On Wed, Sep 20, 2023 at 03:09:54PM +0200, Alvin Šipraga wrote:
> From: Alvin Šipraga <[email protected]>
>
> For applications where the PLL must be adjusted without glitches in the
> clock output(s), a new silabs,pll-reset-mode property is added. It
> can be used to specify whether or not the PLL should be reset after
> adjustment. Resetting is known to cause glitches.
>
> For compatibility with older device trees, it must be assumed that the
> default PLL reset mode is to unconditionally reset after adjustment.
>
> Cc: Sebastian Hesselbarth <[email protected]>
> Cc: Rabeeh Khoury <[email protected]>
> Cc: Jacob Siverskog <[email protected]>
> Cc: Sergej Sawazki <[email protected]>
> Signed-off-by: Alvin Šipraga <[email protected]>
> ---
> .../bindings/clock/silabs,si5351.yaml | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.yaml b/Documentation/devicetree/bindings/clock/silabs,si5351.yaml
> index 3ca8d998c48c..b6692b323a66 100644
> --- a/Documentation/devicetree/bindings/clock/silabs,si5351.yaml
> +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.yaml
> @@ -50,6 +50,22 @@ properties:
> Pair of <number source> for each PLL. Allows to overwrite clock source of
> PLL A (number=0) or PLL B (number=1).
>
> + silabs,pll-reset-mode:
> + $ref: /schemas/types.yaml#/definitions/uint32-matrix
> + minItems: 1
> + maxItems: 2
> + description: |
> + Pair of <number mode> for each PLL. Configures the reset mode for PLL A
> + (number=0) and/or PLL B (number=1). Mode can be one of:
> +
> + 0 - reset whenever PLL rate is adjusted (default mode)
> + 1 - do not reset when PLL rate is adjusted
> +
> + In mode 1, the PLL is only reset if the silabs,pll-reset is specified in
> + one of the clock output child nodes that also sources the PLL. This mode
> + may be preferable if output clocks are expected to be adjusted without
> + glitches.
Same comments as the other matrix property.
> +
> patternProperties:
> "^clkout@?[0-8]$":
> type: object
> @@ -205,6 +221,9 @@ examples:
> /* Use XTAL input as source of PLL0 and PLL1 */
> silabs,pll-source = <0 0>, <1 0>;
>
> + /* Don't reset PLL1 on rate adjustment */
> + silabs,pll-reset-mode = <1 1>;
> +
> /*
> * Overwrite CLK0 configuration with:
> * - 8 mA output drive strength
> --
> 2.41.0
>