Add OpenCores PWM controller node and add PWM pins configuration
on VisionFive 1 board.
Signed-off-by: William Qiu <[email protected]>
Reviewed-by: Hal Feng <[email protected]>
---
.../boot/dts/starfive/jh7100-common.dtsi | 24 +++++++++++++++++++
arch/riscv/boot/dts/starfive/jh7100.dtsi | 9 +++++++
2 files changed, 33 insertions(+)
diff --git a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
index b93ce351a90f..11876906cc05 100644
--- a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
@@ -84,6 +84,24 @@ GPO_I2C2_PAD_SDA_OEN,
};
};
+ pwm_pins: pwm-0 {
+ pwm-pins {
+ pinmux = <GPIOMUX(7,
+ GPO_PWM_PAD_OUT_BIT0,
+ GPO_PWM_PAD_OE_N_BIT0,
+ GPI_NONE)>,
+ <GPIOMUX(5,
+ GPO_PWM_PAD_OUT_BIT1,
+ GPO_PWM_PAD_OE_N_BIT1,
+ GPI_NONE)>;
+ bias-disable;
+ drive-strength = <35>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
uart3_pins: uart3-0 {
rx-pins {
pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
@@ -154,6 +172,12 @@ &osc_aud {
clock-frequency = <27000000>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins>;
+ status = "okay";
+};
+
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
diff --git a/arch/riscv/boot/dts/starfive/jh7100.dtsi b/arch/riscv/boot/dts/starfive/jh7100.dtsi
index 35ab54fb235f..0bb9e2e5ae68 100644
--- a/arch/riscv/boot/dts/starfive/jh7100.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7100.dtsi
@@ -274,6 +274,15 @@ watchdog@12480000 {
<&rstgen JH7100_RSTN_WDT>;
};
+ pwm: pwm@12490000 {
+ compatible = "starfive,jh71x0-pwm";
+ reg = <0x0 0x12490000 0x0 0x10000>;
+ clocks = <&clkgen JH7100_CLK_PWM_APB>;
+ resets = <&rstgen JH7100_RSTN_PWM_APB>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
sfctemp: temperature-sensor@124a0000 {
compatible = "starfive,jh7100-temp";
reg = <0x0 0x124a0000 0x0 0x10000>;
--
2.34.1