Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
SFP module is present, but no fiber connected, so definitely no carrier.
After booting, eth2 is down, but netdev LED trigger surprisingly reports
link active. Then, after "ip link set eth2 up", the link indicator goes
away - as I would have expected it from the beginning.
It turns out, that the default carrier state after netdev creation is
"carrier ok". Some ethernet drivers explicitly call netif_carrier_off
during probing, others (like mvneta) don't - which explains the current
behaviour: only when the device is brought up, phylink_start calls
netif_carrier_off.
Fix this for all drivers, by calling netif_carrier_off in phylink_create.
Suggested-by: Andrew Lunn <[email protected]>
Signed-off-by: Klaus Kudielka <[email protected]>
---
drivers/net/phy/phylink.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 6712883498..a28da80bde 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1616,6 +1616,7 @@ struct phylink *phylink_create(struct phylink_config *config,
pl->config = config;
if (config->type == PHYLINK_NETDEV) {
pl->netdev = to_net_dev(config->dev);
+ netif_carrier_off(pl->netdev);
} else if (config->type == PHYLINK_DEV) {
pl->dev = config->dev;
} else {
--
2.42.0
On Mon, Nov 06, 2023 at 07:05:06PM +0100, Klaus Kudielka wrote:
> Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
> SFP module is present, but no fiber connected, so definitely no carrier.
>
> After booting, eth2 is down, but netdev LED trigger surprisingly reports
> link active. Then, after "ip link set eth2 up", the link indicator goes
> away - as I would have expected it from the beginning.
>
> It turns out, that the default carrier state after netdev creation is
> "carrier ok". Some ethernet drivers explicitly call netif_carrier_off
> during probing, others (like mvneta) don't - which explains the current
> behaviour: only when the device is brought up, phylink_start calls
> netif_carrier_off.
>
> Fix this for all drivers, by calling netif_carrier_off in phylink_create.
>
> Suggested-by: Andrew Lunn <[email protected]>
> Signed-off-by: Klaus Kudielka <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Thanks!
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
On Mon, Nov 06, 2023 at 07:05:06PM +0100, Klaus Kudielka wrote:
> Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus;
> SFP module is present, but no fiber connected, so definitely no carrier.
>
> After booting, eth2 is down, but netdev LED trigger surprisingly reports
> link active. Then, after "ip link set eth2 up", the link indicator goes
> away - as I would have expected it from the beginning.
>
> It turns out, that the default carrier state after netdev creation is
> "carrier ok". Some ethernet drivers explicitly call netif_carrier_off
> during probing, others (like mvneta) don't - which explains the current
> behaviour: only when the device is brought up, phylink_start calls
> netif_carrier_off.
>
> Fix this for all drivers, by calling netif_carrier_off in phylink_create.
I would actually say: Fix this for all drivers using phylink, by
calling...
You marked this patch for net, so it should be backported. Ideally you
should include a Fixes: tag, indicating when the problem was
introduced. That is bit hard in this case. Its been broken
forever. But adding LED support made this observable. So maybe a
Fixes: tag based on when the LED trigger was added?
You should also add:
Cc: [email protected]
There is more about this in:
https://docs.kernel.org/process/stable-kernel-rules.html
Reviewed-by: Andrew Lunn <[email protected]>
Andrew