2023-11-17 09:31:28

by Jai Luthra

[permalink] [raw]
Subject: [PATCH v2 4/9] arm64: dts: ti: k3-am625-beagleplay: Add overlays for OV5640

Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI

The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.

Signed-off-by: Jai Luthra <[email protected]>
---
arch/arm64/boot/dts/ti/Makefile | 11 ++++
.../dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso | 77 ++++++++++++++++++++++
.../ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso | 77 ++++++++++++++++++++++
3 files changed, 165 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 77a347f9f47d..c6c7825b4cb2 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -12,6 +12,8 @@
k3-am625-sk-hdmi-audio-dtbs := k3-am625-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
k3-am62-lp-sk-hdmi-audio-dtbs := k3-am62-lp-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
@@ -80,7 +82,16 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb

+# Build time test only, enabled by CONFIG_OF_ALL_DTBS
+k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
+ k3-am625-beagleplay-csi2-ov5640.dtbo
+k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
+ k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
+dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
+ k3-am625-beagleplay-csi2-tevi-ov5640.dtb
+
# Enable support for device-tree overlays
+DTC_FLAGS_k3-am625-beagleplay += -@
DTC_FLAGS_k3-am625-sk += -@
DTC_FLAGS_k3-am62-lp-sk += -@
DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
new file mode 100644
index 000000000000..5e80ca7033ba
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ clk_ov5640_fixed: ov5640-xclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+};
+
+&main_gpio0 {
+ p11-hog {
+ /* P11 - CSI2_CAMERA_GPIO1 */
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "CSI2_CAMERA_GPIO1";
+ };
+};
+
+&wkup_i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY. */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&dphy0 {
+ status = "okay";
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
new file mode 100644
index 000000000000..5e1cbbc27c8f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
+ * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+ clk_ov5640_fixed: ov5640-xclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+};
+
+&main_gpio0 {
+ p11-hog {
+ /* P11 - CSI2_CAMERA_GPIO1 */
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "CSI2_CAMERA_GPIO1";
+ };
+};
+
+&wkup_i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+
+ clocks = <&clk_ov5640_fixed>;
+ clock-names = "xclk";
+
+ port {
+ csi2_cam0: endpoint {
+ remote-endpoint = <&csi2rx0_in_sensor>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&cdns_csi2rx0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_port0: port@0 {
+ reg = <0>;
+ status = "okay";
+
+ csi2rx0_in_sensor: endpoint {
+ remote-endpoint = <&csi2_cam0>;
+ bus-type = <4>; /* CSI2 DPHY. */
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+};
+
+&dphy0 {
+ status = "okay";
+};
+
+&ti_csi2rx0 {
+ status = "okay";
+};

--
2.42.1


2023-11-20 16:04:18

by Andrew Davis

[permalink] [raw]
Subject: Re: [PATCH v2 4/9] arm64: dts: ti: k3-am625-beagleplay: Add overlays for OV5640

On 11/17/23 3:28 AM, Jai Luthra wrote:
> Three different OV5640 modules are supported using the FFC connector on
> BeaglePlay:
> - Digilent PCam 5C
> - ALINX AN5641
> - TEVI-OV5640-*-RPI
>
> The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
> the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
> overlay.
>
> Signed-off-by: Jai Luthra <[email protected]>
> ---
> arch/arm64/boot/dts/ti/Makefile | 11 ++++
> .../dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso | 77 ++++++++++++++++++++++
> .../ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso | 77 ++++++++++++++++++++++
> 3 files changed, 165 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 77a347f9f47d..c6c7825b4cb2 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -12,6 +12,8 @@
> k3-am625-sk-hdmi-audio-dtbs := k3-am625-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
> k3-am62-lp-sk-hdmi-audio-dtbs := k3-am62-lp-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
> dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-ov5640.dtbo
> +dtb-$(CONFIG_ARCH_K3) += k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
> dtb-$(CONFIG_ARCH_K3) += k3-am625-phyboard-lyra-rdk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am625-verdin-nonwifi-dahlia.dtb
> @@ -80,7 +82,16 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-evm.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
>
> +# Build time test only, enabled by CONFIG_OF_ALL_DTBS
> +k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
> + k3-am625-beagleplay-csi2-ov5640.dtbo
> +k3-am625-beagleplay-csi2-tevi-ov5640-dtbs := k3-am625-beagleplay.dtb \
> + k3-am625-beagleplay-csi2-tevi-ov5640.dtbo
> +dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
> + k3-am625-beagleplay-csi2-tevi-ov5640.dtb
> +
> # Enable support for device-tree overlays
> +DTC_FLAGS_k3-am625-beagleplay += -@

Too bad the build test check doesn't add this for us, might be time
to just make this default, I see broadcom/Makefile has:

DTC_FLAGS := -@

Well we can look into that later, this patch LGTM,

Reviewed-by: Andrew Davis <[email protected]>

> DTC_FLAGS_k3-am625-sk += -@
> DTC_FLAGS_k3-am62-lp-sk += -@
> DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
> new file mode 100644
> index 000000000000..5e80ca7033ba
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-ov5640.dtso
> @@ -0,0 +1,77 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ALINX AN5641 & Digilent PCam 5C - OV5640 camera module
> + * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +&{/} {
> + clk_ov5640_fixed: ov5640-xclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <12000000>;
> + };
> +};
> +
> +&main_gpio0 {
> + p11-hog {
> + /* P11 - CSI2_CAMERA_GPIO1 */
> + gpio-hog;
> + gpios = <11 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO1";
> + };
> +};
> +
> +&wkup_i2c0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + ov5640: camera@3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> +
> + clocks = <&clk_ov5640_fixed>;
> + clock-names = "xclk";
> +
> + port {
> + csi2_cam0: endpoint {
> + remote-endpoint = <&csi2rx0_in_sensor>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&cdns_csi2rx0 {
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + csi0_port0: port@0 {
> + reg = <0>;
> + status = "okay";
> +
> + csi2rx0_in_sensor: endpoint {
> + remote-endpoint = <&csi2_cam0>;
> + bus-type = <4>; /* CSI2 DPHY. */
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&dphy0 {
> + status = "okay";
> +};
> +
> +&ti_csi2rx0 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
> new file mode 100644
> index 000000000000..5e1cbbc27c8f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay-csi2-tevi-ov5640.dtso
> @@ -0,0 +1,77 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Technexion TEVI-OV5640-*-RPI - OV5640 camera module
> + * Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +&{/} {
> + clk_ov5640_fixed: ov5640-xclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24000000>;
> + };
> +};
> +
> +&main_gpio0 {
> + p11-hog {
> + /* P11 - CSI2_CAMERA_GPIO1 */
> + gpio-hog;
> + gpios = <11 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "CSI2_CAMERA_GPIO1";
> + };
> +};
> +
> +&wkup_i2c0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + ov5640: camera@3c {
> + compatible = "ovti,ov5640";
> + reg = <0x3c>;
> +
> + clocks = <&clk_ov5640_fixed>;
> + clock-names = "xclk";
> +
> + port {
> + csi2_cam0: endpoint {
> + remote-endpoint = <&csi2rx0_in_sensor>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&cdns_csi2rx0 {
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + csi0_port0: port@0 {
> + reg = <0>;
> + status = "okay";
> +
> + csi2rx0_in_sensor: endpoint {
> + remote-endpoint = <&csi2_cam0>;
> + bus-type = <4>; /* CSI2 DPHY. */
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +};
> +
> +&dphy0 {
> + status = "okay";
> +};
> +
> +&ti_csi2rx0 {
> + status = "okay";
> +};
>