From: Hugo Villeneuve <[email protected]>
Hello,
this patch series improves regmap debugfs by using one regmap per port.
I have tested the changes on a custom board with two SC16IS752 DUART using a
Variscite IMX8MN NANO SOM.
Thank you.
Link: [v1] https://lore.kernel.org/all/[email protected]/
Changes for V2:
- Remove now useless line variable in struct sc16is7xx_one
Hugo Villeneuve (1):
serial: sc16is7xx: improve regmap debugfs by using one regmap per port
drivers/tty/serial/sc16is7xx.c | 145 ++++++++++++++++++---------------
1 file changed, 81 insertions(+), 64 deletions(-)
base-commit: 98b1cc82c4affc16f5598d4fa14b1858671b2263
--
2.39.2
From: Hugo Villeneuve <[email protected]>
With this current driver regmap implementation, it is hard to make sense
of the register addresses displayed using the regmap debugfs interface,
because they do not correspond to the actual register addresses documented
in the datasheet. For example, register 1 is displayed as registers 04 thru
07:
$ cat /sys/kernel/debug/regmap/spi0.0/registers
04: 10 -> Port 0, register offset 1
05: 10 -> Port 1, register offset 1
06: 00 -> Port 2, register offset 1 -> invalid
07: 00 -> port 3, register offset 1 -> invalid
...
The reason is that bits 0 and 1 of the register address correspond to the
channel (port) bits, so the register address itself starts at bit 2, and we
must 'mentally' shift each register address by 2 bits to get its real
address/offset.
Also, only channels 0 and 1 are supported by the chip, so channel mask
combinations of 10b and 11b are invalid, and the display of these
registers is useless.
This patch adds a separate regmap configuration for each port, similar to
what is done in the max310x driver, so that register addresses displayed
match the register addresses in the chip datasheet. Also, each port now has
its own debugfs entry.
Example with new regmap implementation:
$ cat /sys/kernel/debug/regmap/spi0.0-port0/registers
1: 10
2: 01
3: 00
...
$ cat /sys/kernel/debug/regmap/spi0.0-port1/registers
1: 10
2: 01
3: 00
As an added bonus, this also simplifies some operations (read/write/modify)
because it is no longer necessary to manually shift register addresses.
Signed-off-by: Hugo Villeneuve <[email protected]>
---
drivers/tty/serial/sc16is7xx.c | 145 ++++++++++++++++++---------------
1 file changed, 81 insertions(+), 64 deletions(-)
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index db2bb1c0d36c..b23d3308c92f 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -300,8 +300,8 @@
/* Misc definitions */
+#define SC16IS7XX_SPI_READ_BIT BIT(7)
#define SC16IS7XX_FIFO_SIZE (64)
-#define SC16IS7XX_REG_SHIFT 2
#define SC16IS7XX_GPIOS_PER_BANK 4
struct sc16is7xx_devtype {
@@ -322,7 +322,7 @@ struct sc16is7xx_one_config {
struct sc16is7xx_one {
struct uart_port port;
- u8 line;
+ struct regmap *regmap;
struct kthread_work tx_work;
struct kthread_work reg_work;
struct kthread_delayed_work ms_work;
@@ -360,48 +360,37 @@ static void sc16is7xx_stop_tx(struct uart_port *port);
#define to_sc16is7xx_one(p,e) ((container_of((p), struct sc16is7xx_one, e)))
-static int sc16is7xx_line(struct uart_port *port)
-{
- struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
-
- return one->line;
-}
-
static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg)
{
- struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
+ struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
unsigned int val = 0;
- const u8 line = sc16is7xx_line(port);
- regmap_read(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, &val);
+ regmap_read(one->regmap, reg, &val);
return val;
}
static void sc16is7xx_port_write(struct uart_port *port, u8 reg, u8 val)
{
- struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
- const u8 line = sc16is7xx_line(port);
+ struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
- regmap_write(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, val);
+ regmap_write(one->regmap, reg, val);
}
static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen)
{
struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
- const u8 line = sc16is7xx_line(port);
- u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line;
+ struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
- regcache_cache_bypass(s->regmap, true);
- regmap_raw_read(s->regmap, addr, s->buf, rxlen);
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(one->regmap, true);
+ regmap_raw_read(one->regmap, SC16IS7XX_RHR_REG, s->buf, rxlen);
+ regcache_cache_bypass(one->regmap, false);
}
static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send)
{
struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
- const u8 line = sc16is7xx_line(port);
- u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | line;
+ struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
/*
* Don't send zero-length data, at least on SPI it confuses the chip
@@ -410,19 +399,17 @@ static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send)
if (unlikely(!to_send))
return;
- regcache_cache_bypass(s->regmap, true);
- regmap_raw_write(s->regmap, addr, s->buf, to_send);
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(one->regmap, true);
+ regmap_raw_write(one->regmap, SC16IS7XX_THR_REG, s->buf, to_send);
+ regcache_cache_bypass(one->regmap, false);
}
static void sc16is7xx_port_update(struct uart_port *port, u8 reg,
u8 mask, u8 val)
{
- struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
- const u8 line = sc16is7xx_line(port);
+ struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
- regmap_update_bits(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line,
- mask, val);
+ regmap_update_bits(one->regmap, reg, mask, val);
}
static int sc16is7xx_alloc_line(void)
@@ -477,7 +464,7 @@ static const struct sc16is7xx_devtype sc16is762_devtype = {
static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg)
{
- switch (reg >> SC16IS7XX_REG_SHIFT) {
+ switch (reg) {
case SC16IS7XX_RHR_REG:
case SC16IS7XX_IIR_REG:
case SC16IS7XX_LSR_REG:
@@ -496,7 +483,7 @@ static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg)
static bool sc16is7xx_regmap_precious(struct device *dev, unsigned int reg)
{
- switch (reg >> SC16IS7XX_REG_SHIFT) {
+ switch (reg) {
case SC16IS7XX_RHR_REG:
return true;
default:
@@ -509,6 +496,7 @@ static bool sc16is7xx_regmap_precious(struct device *dev, unsigned int reg)
static int sc16is7xx_set_baud(struct uart_port *port, int baud)
{
struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
+ struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
u8 lcr;
u8 prescaler = 0;
unsigned long clk = port->uartclk, div = clk / 16 / baud;
@@ -540,12 +528,12 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
SC16IS7XX_LCR_CONF_MODE_B);
/* Enable enhanced features */
- regcache_cache_bypass(s->regmap, true);
+ regcache_cache_bypass(one->regmap, true);
sc16is7xx_port_update(port, SC16IS7XX_EFR_REG,
SC16IS7XX_EFR_ENABLE_BIT,
SC16IS7XX_EFR_ENABLE_BIT);
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(one->regmap, false);
/* Put LCR back to the normal mode */
sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);
@@ -561,10 +549,10 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
SC16IS7XX_LCR_CONF_MODE_A);
/* Write the new divisor */
- regcache_cache_bypass(s->regmap, true);
+ regcache_cache_bypass(one->regmap, true);
sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256);
sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256);
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(one->regmap, false);
/* Put LCR back to the normal mode */
sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);
@@ -1078,7 +1066,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
SC16IS7XX_LCR_CONF_MODE_B);
/* Configure flow control */
- regcache_cache_bypass(s->regmap, true);
+ regcache_cache_bypass(one->regmap, true);
sc16is7xx_port_write(port, SC16IS7XX_XON1_REG, termios->c_cc[VSTART]);
sc16is7xx_port_write(port, SC16IS7XX_XOFF1_REG, termios->c_cc[VSTOP]);
@@ -1097,7 +1085,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
SC16IS7XX_EFR_REG,
SC16IS7XX_EFR_FLOWCTRL_BITS,
flow);
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(one->regmap, false);
/* Update LCR register */
sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);
@@ -1148,7 +1136,6 @@ static int sc16is7xx_config_rs485(struct uart_port *port, struct ktermios *termi
static int sc16is7xx_startup(struct uart_port *port)
{
struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
- struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
unsigned int val;
unsigned long flags;
@@ -1165,7 +1152,7 @@ static int sc16is7xx_startup(struct uart_port *port)
sc16is7xx_port_write(port, SC16IS7XX_LCR_REG,
SC16IS7XX_LCR_CONF_MODE_B);
- regcache_cache_bypass(s->regmap, true);
+ regcache_cache_bypass(one->regmap, true);
/* Enable write access to enhanced features and internal clock div */
sc16is7xx_port_update(port, SC16IS7XX_EFR_REG,
@@ -1183,7 +1170,7 @@ static int sc16is7xx_startup(struct uart_port *port)
SC16IS7XX_TCR_RX_RESUME(24) |
SC16IS7XX_TCR_RX_HALT(48));
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(one->regmap, false);
/* Now, initialize the UART */
sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, SC16IS7XX_LCR_WORD_LEN_8);
@@ -1464,7 +1451,7 @@ static int sc16is7xx_setup_mctrl_ports(struct sc16is7xx_port *s)
if (s->mctrl_mask)
regmap_update_bits(
s->regmap,
- SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT,
+ SC16IS7XX_IOCONTROL_REG,
SC16IS7XX_IOCONTROL_MODEM_A_BIT |
SC16IS7XX_IOCONTROL_MODEM_B_BIT, s->mctrl_mask);
@@ -1479,7 +1466,7 @@ static const struct serial_rs485 sc16is7xx_rs485_supported = {
static int sc16is7xx_probe(struct device *dev,
const struct sc16is7xx_devtype *devtype,
- struct regmap *regmap, int irq)
+ struct regmap *regmaps[], int irq)
{
unsigned long freq = 0, *pfreq = dev_get_platdata(dev);
unsigned int val;
@@ -1487,16 +1474,16 @@ static int sc16is7xx_probe(struct device *dev,
int i, ret;
struct sc16is7xx_port *s;
- if (IS_ERR(regmap))
- return PTR_ERR(regmap);
+ for (i = 0; i < devtype->nr_uart; i++)
+ if (IS_ERR(regmaps[i]))
+ return PTR_ERR(regmaps[i]);
/*
* This device does not have an identification register that would
* tell us if we are really connected to the correct device.
* The best we can do is to check if communication is at all possible.
*/
- ret = regmap_read(regmap,
- SC16IS7XX_LSR_REG << SC16IS7XX_REG_SHIFT, &val);
+ ret = regmap_read(regmaps[0], SC16IS7XX_LSR_REG, &val);
if (ret < 0)
return -EPROBE_DEFER;
@@ -1530,7 +1517,7 @@ static int sc16is7xx_probe(struct device *dev,
return -EINVAL;
}
- s->regmap = regmap;
+ s->regmap = regmaps[0];
s->devtype = devtype;
dev_set_drvdata(dev, s);
mutex_init(&s->efr_lock);
@@ -1545,11 +1532,10 @@ static int sc16is7xx_probe(struct device *dev,
sched_set_fifo(s->kworker_task);
/* reset device, purging any pending irq / data */
- regmap_write(s->regmap, SC16IS7XX_IOCONTROL_REG << SC16IS7XX_REG_SHIFT,
- SC16IS7XX_IOCONTROL_SRESET_BIT);
+ regmap_write(s->regmap, SC16IS7XX_IOCONTROL_REG,
+ SC16IS7XX_IOCONTROL_SRESET_BIT);
for (i = 0; i < devtype->nr_uart; ++i) {
- s->p[i].line = i;
/* Initialize port data */
s->p[i].port.dev = dev;
s->p[i].port.irq = irq;
@@ -1570,6 +1556,7 @@ static int sc16is7xx_probe(struct device *dev,
s->p[i].port.ops = &sc16is7xx_ops;
s->p[i].old_mctrl = 0;
s->p[i].port.line = sc16is7xx_alloc_line();
+ s->p[i].regmap = regmaps[i];
if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) {
ret = -ENOMEM;
@@ -1598,13 +1585,13 @@ static int sc16is7xx_probe(struct device *dev,
sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG,
SC16IS7XX_LCR_CONF_MODE_B);
- regcache_cache_bypass(s->regmap, true);
+ regcache_cache_bypass(regmaps[i], true);
/* Enable write access to enhanced features */
sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFR_REG,
SC16IS7XX_EFR_ENABLE_BIT);
- regcache_cache_bypass(s->regmap, false);
+ regcache_cache_bypass(regmaps[i], false);
/* Restore access to general registers */
sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_LCR_REG, 0x00);
@@ -1698,19 +1685,36 @@ static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = {
MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids);
static struct regmap_config regcfg = {
- .reg_bits = 7,
- .pad_bits = 1,
+ .reg_bits = 5,
+ .pad_bits = 3,
.val_bits = 8,
.cache_type = REGCACHE_RBTREE,
.volatile_reg = sc16is7xx_regmap_volatile,
.precious_reg = sc16is7xx_regmap_precious,
+ .max_register = SC16IS7XX_EFCR_REG,
};
+static const char *sc16is7xx_regmap_name(unsigned int port_id)
+{
+ static char buf[6];
+
+ snprintf(buf, sizeof(buf), "port%d", port_id);
+
+ return buf;
+}
+
+static unsigned int sc16is7xx_regmap_port_mask(unsigned int port_id)
+{
+ /* CH1,CH0 are at bits 2:1. */
+ return port_id << 1;
+}
+
#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
static int sc16is7xx_spi_probe(struct spi_device *spi)
{
const struct sc16is7xx_devtype *devtype;
- struct regmap *regmap;
+ struct regmap *regmaps[2];
+ unsigned int i;
int ret;
/* Setup SPI bus */
@@ -1732,11 +1736,20 @@ static int sc16is7xx_spi_probe(struct spi_device *spi)
devtype = (struct sc16is7xx_devtype *)id_entry->driver_data;
}
- regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
- (devtype->nr_uart - 1);
- regmap = devm_regmap_init_spi(spi, ®cfg);
+ for (i = 0; i < devtype->nr_uart; i++) {
+ regcfg.name = sc16is7xx_regmap_name(i);
+ /*
+ * If read_flag_mask is 0, the regmap code sets it to a default
+ * of 0x80. Since we specify our own mask, we must add the READ
+ * bit ourselves:
+ */
+ regcfg.read_flag_mask = sc16is7xx_regmap_port_mask(i) |
+ SC16IS7XX_SPI_READ_BIT;
+ regcfg.write_flag_mask = sc16is7xx_regmap_port_mask(i);
+ regmaps[i] = devm_regmap_init_spi(spi, ®cfg);
+ }
- return sc16is7xx_probe(&spi->dev, devtype, regmap, spi->irq);
+ return sc16is7xx_probe(&spi->dev, devtype, regmaps, spi->irq);
}
static void sc16is7xx_spi_remove(struct spi_device *spi)
@@ -1775,7 +1788,8 @@ static int sc16is7xx_i2c_probe(struct i2c_client *i2c)
{
const struct i2c_device_id *id = i2c_client_get_device_id(i2c);
const struct sc16is7xx_devtype *devtype;
- struct regmap *regmap;
+ struct regmap *regmaps[2];
+ unsigned int i;
if (i2c->dev.of_node) {
devtype = device_get_match_data(&i2c->dev);
@@ -1785,11 +1799,14 @@ static int sc16is7xx_i2c_probe(struct i2c_client *i2c)
devtype = (struct sc16is7xx_devtype *)id->driver_data;
}
- regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
- (devtype->nr_uart - 1);
- regmap = devm_regmap_init_i2c(i2c, ®cfg);
+ for (i = 0; i < devtype->nr_uart; i++) {
+ regcfg.name = sc16is7xx_regmap_name(i);
+ regcfg.read_flag_mask = sc16is7xx_regmap_port_mask(i);
+ regcfg.write_flag_mask = sc16is7xx_regmap_port_mask(i);
+ regmaps[i] = devm_regmap_init_i2c(i2c, ®cfg);
+ }
- return sc16is7xx_probe(&i2c->dev, devtype, regmap, i2c->irq);
+ return sc16is7xx_probe(&i2c->dev, devtype, regmaps, i2c->irq);
}
static void sc16is7xx_i2c_remove(struct i2c_client *client)
--
2.39.2
On 20. 11. 23, 17:39, Hugo Villeneuve wrote:
> From: Hugo Villeneuve <[email protected]>
>
> With this current driver regmap implementation, it is hard to make sense
> of the register addresses displayed using the regmap debugfs interface,
> because they do not correspond to the actual register addresses documented
> in the datasheet. For example, register 1 is displayed as registers 04 thru
> 07:
...
> --- a/drivers/tty/serial/sc16is7xx.c
> +++ b/drivers/tty/serial/sc16is7xx.c
...
> #ifdef CONFIG_SERIAL_SC16IS7XX_SPI
> static int sc16is7xx_spi_probe(struct spi_device *spi)
> {
> const struct sc16is7xx_devtype *devtype;
> - struct regmap *regmap;
> + struct regmap *regmaps[2];
IMO, in all places, it would make sense to declare a VLA with
devtype->nr_uart.
> + unsigned int i;
> int ret;
>
> /* Setup SPI bus */
> @@ -1732,11 +1736,20 @@ static int sc16is7xx_spi_probe(struct spi_device *spi)
> devtype = (struct sc16is7xx_devtype *)id_entry->driver_data;
> }
>
> - regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
> - (devtype->nr_uart - 1);
> - regmap = devm_regmap_init_spi(spi, ®cfg);
> + for (i = 0; i < devtype->nr_uart; i++) {
> + regcfg.name = sc16is7xx_regmap_name(i);
> + /*
> + * If read_flag_mask is 0, the regmap code sets it to a default
> + * of 0x80. Since we specify our own mask, we must add the READ
> + * bit ourselves:
> + */
> + regcfg.read_flag_mask = sc16is7xx_regmap_port_mask(i) |
> + SC16IS7XX_SPI_READ_BIT;
> + regcfg.write_flag_mask = sc16is7xx_regmap_port_mask(i);
> + regmaps[i] = devm_regmap_init_spi(spi, ®cfg);
As you trip over the array until devtype->nr_uart which is of course up
to 2. For now.
Or at least add an asserion: devtype->nr_uart <= 2 somewhere.
thanks,
--
js
suse labs
On Tue, 21 Nov 2023 06:57:56 +0100
Jiri Slaby <[email protected]> wrote:
> On 20. 11. 23, 17:39, Hugo Villeneuve wrote:
> > From: Hugo Villeneuve <[email protected]>
> >
> > With this current driver regmap implementation, it is hard to make sense
> > of the register addresses displayed using the regmap debugfs interface,
> > because they do not correspond to the actual register addresses documented
> > in the datasheet. For example, register 1 is displayed as registers 04 thru
> > 07:
> ...
> > --- a/drivers/tty/serial/sc16is7xx.c
> > +++ b/drivers/tty/serial/sc16is7xx.c
> ...
> > #ifdef CONFIG_SERIAL_SC16IS7XX_SPI
> > static int sc16is7xx_spi_probe(struct spi_device *spi)
> > {
> > const struct sc16is7xx_devtype *devtype;
> > - struct regmap *regmap;
> > + struct regmap *regmaps[2];
>
> IMO, in all places, it would make sense to declare a VLA with
> devtype->nr_uart.
Hi Jiri,
are VLA now allowed in kernel code?
> > + unsigned int i;
> > int ret;
> >
> > /* Setup SPI bus */
> > @@ -1732,11 +1736,20 @@ static int sc16is7xx_spi_probe(struct spi_device *spi)
> > devtype = (struct sc16is7xx_devtype *)id_entry->driver_data;
> > }
> >
> > - regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
> > - (devtype->nr_uart - 1);
> > - regmap = devm_regmap_init_spi(spi, ®cfg);
> > + for (i = 0; i < devtype->nr_uart; i++) {
> > + regcfg.name = sc16is7xx_regmap_name(i);
> > + /*
> > + * If read_flag_mask is 0, the regmap code sets it to a default
> > + * of 0x80. Since we specify our own mask, we must add the READ
> > + * bit ourselves:
> > + */
> > + regcfg.read_flag_mask = sc16is7xx_regmap_port_mask(i) |
> > + SC16IS7XX_SPI_READ_BIT;
> > + regcfg.write_flag_mask = sc16is7xx_regmap_port_mask(i);
> > + regmaps[i] = devm_regmap_init_spi(spi, ®cfg);
>
> As you trip over the array until devtype->nr_uart which is of course up
> to 2. For now.
>
> Or at least add an asserion: devtype->nr_uart <= 2 somewhere.
devtype->nr_uart is coming from const struct sc16is7xx_devtype, so it
is always a constant, do we need an assert in this case?
Hugo.
> thanks,
> --
> js
> suse labs
>
>