Add the ADSP Generic Packet Router (GPR) device node as part of audio
subsystem in Qualcomm SM8650 SoC.
Cc: Neil Armstrong <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Changes in v2:
1. bedais/dais order (Konrad)
---
arch/arm64/boot/dts/qcom/sm8650.dtsi | 40 ++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index 41dfa5e19a15..8d327f83edc8 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -4326,6 +4326,46 @@ fastrpc {
#address-cells = <1>;
#size-cells = <0>;
};
+
+ gpr {
+ compatible = "qcom,gpr";
+ qcom,glink-channels = "adsp_apps";
+ qcom,domain = <GPR_DOMAIN_ID_ADSP>;
+ qcom,intents = <512 20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ q6apm: service@1 {
+ compatible = "qcom,q6apm";
+ reg = <GPR_APM_MODULE_IID>;
+ #sound-dai-cells = <0>;
+ qcom,protection-domain = "avs/audio",
+ "msm/adsp/audio_pd";
+
+ q6apmbedai: bedais {
+ compatible = "qcom,q6apm-lpass-dais";
+ #sound-dai-cells = <1>;
+ };
+
+ q6apmdai: dais {
+ compatible = "qcom,q6apm-dais";
+ iommus = <&apps_smmu 0x1001 0x80>,
+ <&apps_smmu 0x1061 0x0>;
+ };
+ };
+
+ q6prm: service@2 {
+ compatible = "qcom,q6prm";
+ reg = <GPR_PRM_MODULE_IID>;
+ qcom,protection-domain = "avs/audio",
+ "msm/adsp/audio_pd";
+
+ q6prmcc: clock-controller {
+ compatible = "qcom,q6prm-lpass-clocks";
+ #clock-cells = <2>;
+ };
+ };
+ };
};
};
--
2.34.1
Add the Low Power Audio SubSystem Low Power Island (LPASS LPI) pin
controller device node as part of audio subsystem in Qualcomm SM8650
SoC.
Cc: Neil Armstrong <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
arch/arm64/boot/dts/qcom/sm8650.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index 8d327f83edc8..bef4582f2a26 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -21,6 +21,7 @@
#include <dt-bindings/reset/qcom,sm8650-gpucc.h>
#include <dt-bindings/soc/qcom,gpr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
#include <dt-bindings/thermal/thermal.h>
/ {
@@ -2610,6 +2611,19 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
};
};
+ lpass_tlmm: pinctrl@6e80000 {
+ compatible = "qcom,sm8650-lpass-lpi-pinctrl";
+ reg = <0 0x06e80000 0 0x20000>;
+
+ clocks = <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "core", "audio";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&lpass_tlmm 0 0 23>;
+ };
+
lpass_lpiaon_noc: interconnect@7400000 {
compatible = "qcom,sm8650-lpass-lpiaon-noc";
reg = <0 0x07400000 0 0x19080>;
--
2.34.1
Add nodes for LPASS Soundwire v2.0.0 controllers. Use labels with
indices matching downstream DTS, to make any comparisons easier.
Cc: Neil Armstrong <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Changes in v2:
1. pinctrl-n/names order (Konrad)
---
arch/arm64/boot/dts/qcom/sm8650.dtsi | 226 +++++++++++++++++++++++++++
1 file changed, 226 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index 49bc52271301..68d28a955ecf 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -2628,6 +2628,36 @@ lpass_wsa2macro: codec@6aa0000 {
#sound-dai-cells = <1>;
};
+ swr3: soundwire@6ab0000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06ab0000 0 0x10000>;
+ interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&lpass_wsa2macro>;
+ clock-names = "iface";
+ label = "WSA2";
+
+ pinctrl-0 = <&wsa2_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <9>;
+
+ qcom,ports-sinterval = /bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x18f 0xff 0xff 0x0f 0x0f 0xff 0x31f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
lpass_rxmacro: codec@6ac0000 {
compatible = "qcom,sm8650-lpass-rx-macro", "qcom,sm8550-lpass-rx-macro";
reg = <0 0x06ac0000 0 0x1000>;
@@ -2645,6 +2675,36 @@ lpass_rxmacro: codec@6ac0000 {
#sound-dai-cells = <1>;
};
+ swr1: soundwire@6ad0000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06ad0000 0 0x10000>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&lpass_rxmacro>;
+ clock-names = "iface";
+ label = "RX";
+
+ pinctrl-0 = <&rx_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <0>;
+ qcom,dout-ports = <11>;
+
+ qcom,ports-sinterval = /bits/ 16 <0x03 0x1f 0x1f 0x07 0x03 0xff 0xff 0x31 0xff 0xff 0xff>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x09 0x01 0xff 0xff 0x00 0xff 0xff 0xff>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00 0xff 0xff 0x00 0xff 0xff 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff 0xff 0xff 0x00 0xff 0xff 0xff>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff 0xff 0xff 0x0f 0xff 0xff 0xff>;
+ qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff 0xff 0xff 0x18 0xff 0xff 0xff>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff 0xff 0xff 0x01 0xff 0xff 0xff>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0x01 0x03 0xff 0xff 0x00 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00 0xff 0xff 0x01 0xff 0xff 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
lpass_txmacro: codec@6ae0000 {
compatible = "qcom,sm8650-lpass-tx-macro", "qcom,sm8550-lpass-tx-macro";
reg = <0 0x06ae0000 0 0x1000>;
@@ -2682,6 +2742,68 @@ lpass_wsamacro: codec@6b00000 {
#sound-dai-cells = <1>;
};
+ swr0: soundwire@6b10000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06b10000 0 0x10000>;
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&lpass_wsamacro>;
+ clock-names = "iface";
+ label = "WSA";
+
+ pinctrl-0 = <&wsa_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <9>;
+
+ qcom,ports-sinterval = /bits/ 16 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x18f 0xff 0xff 0x0f 0x0f 0xff 0x31f>;
+ qcom,ports-offset1 = /bits/ 8 <0x01 0x03 0x05 0x02 0x04 0x15 0x00 0xff 0xff 0x06 0x0d 0xff 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0xff 0x07 0x1f 0xff 0x07 0x1f 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x0f>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0x08 0xff 0xff 0xff 0xff 0xff 0x18>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0x00 0x01 0x01 0x00 0x01 0x01 0x00 0x00 0x00 0x01 0x01 0x00 0x00>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
+ swr2: soundwire@6d30000 {
+ compatible = "qcom,soundwire-v2.0.0";
+ reg = <0 0x06d30000 0 0x10000>;
+ interrupts = <GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 520 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "core", "wakeup";
+ clocks = <&lpass_txmacro>;
+ clock-names = "iface";
+ label = "TX";
+
+ pinctrl-0 = <&tx_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <0>;
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x01 0x01 0x03 0x03>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x01 0x01>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x02 0x00 0x00>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
lpass_vamacro: codec@6d44000 {
compatible = "qcom,sm8650-lpass-va-macro", "qcom,sm8550-lpass-va-macro";
reg = <0 0x06d44000 0 0x1000>;
@@ -2708,6 +2830,110 @@ lpass_tlmm: pinctrl@6e80000 {
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&lpass_tlmm 0 0 23>;
+
+ tx_swr_active: tx-swr-active-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "swr_tx_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio1", "gpio2", "gpio14";
+ function = "swr_tx_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ rx_swr_active: rx-swr-active-state {
+ clk-pins {
+ pins = "gpio3";
+ function = "swr_rx_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio4", "gpio5";
+ function = "swr_rx_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ dmic01_default: dmic01-default-state {
+ clk-pins {
+ pins = "gpio6";
+ function = "dmic1_clk";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ data-pins {
+ pins = "gpio7";
+ function = "dmic1_data";
+ drive-strength = <8>;
+ input-enable;
+ };
+ };
+
+ dmic02_default: dmic02-default-state {
+ clk-pins {
+ pins = "gpio8";
+ function = "dmic2_clk";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ data-pins {
+ pins = "gpio9";
+ function = "dmic2_data";
+ drive-strength = <8>;
+ input-enable;
+ };
+ };
+
+ wsa_swr_active: wsa-swr-active-state {
+ clk-pins {
+ pins = "gpio10";
+ function = "wsa_swr_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio11";
+ function = "wsa_swr_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
+
+ wsa2_swr_active: wsa2-swr-active-state {
+ clk-pins {
+ pins = "gpio15";
+ function = "wsa2_swr_clk";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio16";
+ function = "wsa2_swr_data";
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+ };
+ };
};
lpass_lpiaon_noc: interconnect@7400000 {
--
2.34.1
Add nodes for WSA8845 speakers on SM8650 MTP board.
Cc: Neil Armstrong <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Changes in v2:
1. pinctrl-n/names order (Konrad)
---
arch/arm64/boot/dts/qcom/sm8650-mtp.dts | 48 +++++++++++++++++++++++++
1 file changed, 48 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
index 656cdbc6f234..9d916edb1c73 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-mtp.dts
@@ -434,6 +434,16 @@ &dispcc {
status = "okay";
};
+&lpass_tlmm {
+ spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
&mdss {
status = "okay";
};
@@ -580,6 +590,36 @@ &sleep_clk {
clock-frequency = <32000>;
};
+&swr0 {
+ status = "okay";
+
+ /* WSA8845, Speaker Left */
+ left_spkr: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ pinctrl-0 = <&spkr_1_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&lpass_tlmm 21 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l3c_1p2>;
+ };
+
+ /* WSA8845, Speaker Right */
+ right_spkr: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ pinctrl-0 = <&spkr_2_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l3c_1p2>;
+ };
+};
+
&tlmm {
/* Reserved I/Os for NFC */
gpio-reserved-ranges = <32 8>;
@@ -611,6 +651,14 @@ mdp_vsync_suspend: mdp-vsync-suspend-state {
drive-strength = <2>;
bias-pull-down;
};
+
+ spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+ pins = "gpio77";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
};
&uart15 {
--
2.34.1
Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8650. The nodes are very similar to SM8550.
Cc: Neil Armstrong <[email protected]>
Signed-off-by: Krzysztof Kozlowski <[email protected]>
---
Bindings were documented here:
https://lore.kernel.org/linux-devicetree/[email protected]/
Changes in v2:
1. Drop assigned-clock-rates, split clock-names into multiple lines (Konrad)
---
arch/arm64/boot/dts/qcom/sm8650.dtsi | 86 ++++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index bef4582f2a26..49bc52271301 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -2611,6 +2611,92 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
};
};
+ lpass_wsa2macro: codec@6aa0000 {
+ compatible = "qcom,sm8650-lpass-wsa-macro", "qcom,sm8550-lpass-wsa-macro";
+ reg = <0 0x06aa0000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_WSA2_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&lpass_vamacro>;
+ clock-names = "mclk",
+ "macro",
+ "dcodec",
+ "fsgen";
+
+ #clock-cells = <0>;
+ clock-output-names = "wsa2-mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ lpass_rxmacro: codec@6ac0000 {
+ compatible = "qcom,sm8650-lpass-rx-macro", "qcom,sm8550-lpass-rx-macro";
+ reg = <0 0x06ac0000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_RX_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&lpass_vamacro>;
+ clock-names = "mclk",
+ "macro",
+ "dcodec",
+ "fsgen";
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ lpass_txmacro: codec@6ae0000 {
+ compatible = "qcom,sm8650-lpass-tx-macro", "qcom,sm8550-lpass-tx-macro";
+ reg = <0 0x06ae0000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&lpass_vamacro>;
+ clock-names = "mclk",
+ "macro",
+ "dcodec",
+ "fsgen";
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ lpass_wsamacro: codec@6b00000 {
+ compatible = "qcom,sm8650-lpass-wsa-macro", "qcom,sm8550-lpass-wsa-macro";
+ reg = <0 0x06b00000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&lpass_vamacro>;
+ clock-names = "mclk",
+ "macro",
+ "dcodec",
+ "fsgen";
+
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_WSA_CORE_TX_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <19200000>;
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ lpass_vamacro: codec@6d44000 {
+ compatible = "qcom,sm8650-lpass-va-macro", "qcom,sm8550-lpass-va-macro";
+ reg = <0 0x06d44000 0 0x1000>;
+ clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "mclk",
+ "macro",
+ "dcodec";
+
+ #clock-cells = <0>;
+ clock-output-names = "fsgen";
+ #sound-dai-cells = <1>;
+ };
+
lpass_tlmm: pinctrl@6e80000 {
compatible = "qcom,sm8650-lpass-lpi-pinctrl";
reg = <0 0x06e80000 0 0x20000>;
--
2.34.1
On 12/4/23 16:57, Krzysztof Kozlowski wrote:
> Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
> Qualcomm SM8650. The nodes are very similar to SM8550.
>
> Cc: Neil Armstrong <[email protected]>
> Signed-off-by: Krzysztof Kozlowski <[email protected]>
>
> ---
Acked-by: Konrad Dybcio <[email protected]>
Konrad
On Mon, 04 Dec 2023 16:57:42 +0100, Krzysztof Kozlowski wrote:
> Add the ADSP Generic Packet Router (GPR) device node as part of audio
> subsystem in Qualcomm SM8650 SoC.
>
>
Applied, thanks!
[1/5] arm64: dts: qcom: sm8650: add ADSP GPR
commit: ff28260e3d9820a22d9bf826bdf219d6efa97260
[2/5] arm64: dts: qcom: sm8650: add LPASS LPI pin controller
commit: 2d6bc13321c90217e1ffecf50a183f20c00ec3e3
[3/5] arm64: dts: qcom: sm8650: add ADSP audio codec macros
commit: 58872a54e4a858d86301b4fb802fd60c45aad3e1
[4/5] arm64: dts: qcom: sm8650: add Soundwire controllers
commit: 6a45a90c0c475bf6bf573c4ba89e0415506c868a
[5/5] arm64: dts: qcom: sm8650-mtp: add WSA8845 speakers
commit: 80627a5d72b6be2652920db402fe2477f086902b
Best regards,
--
Bjorn Andersson <[email protected]>