Add OpenCores PWM controller node and add PWM pins configuration
on VisionFive 2 board.
Signed-off-by: William Qiu <[email protected]>
---
.../jh7110-starfive-visionfive-2.dtsi | 22 +++++++++++++++++++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 9 ++++++++
2 files changed, 31 insertions(+)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index b89e9791efa7..e08af8a830ab 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -323,6 +323,12 @@ reserved-data@600000 {
};
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins>;
+ status = "okay";
+};
+
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins>;
@@ -513,6 +519,22 @@ GPOEN_ENABLE,
};
};
+ pwm_pins: pwm-0 {
+ pwm-pins {
+ pinmux = <GPIOMUX(46, GPOUT_SYS_PWM_CHANNEL0,
+ GPOEN_SYS_PWM0_CHANNEL0,
+ GPI_NONE)>,
+ <GPIOMUX(59, GPOUT_SYS_PWM_CHANNEL1,
+ GPOEN_SYS_PWM0_CHANNEL1,
+ GPI_NONE)>;
+ bias-disable;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
spi0_pins: spi0-0 {
mosi-pins {
pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 45213cdf50dc..1b782f2c1395 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -829,6 +829,15 @@ i2stx1: i2s@120c0000 {
status = "disabled";
};
+ pwm: pwm@120d0000 {
+ compatible = "starfive,jh7110-pwm", "opencores,pwm-v1";
+ reg = <0x0 0x120d0000 0x0 0x10000>;
+ clocks = <&syscrg JH7110_SYSCLK_PWM_APB>;
+ resets = <&syscrg JH7110_SYSRST_PWM_APB>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
sfctemp: temperature-sensor@120e0000 {
compatible = "starfive,jh7110-temp";
reg = <0x0 0x120e0000 0x0 0x10000>;
--
2.34.1