2023-12-15 11:49:41

by claudiu beznea

[permalink] [raw]
Subject: [PATCH net-next v2 20/21] net: ravb: Do not apply RX CSUM settings to hardware if the interface is down

From: Claudiu Beznea <[email protected]>

Do not apply the RX CSUM settings to hardware if the interface is down. In
case runtime PM is enabled, and while the interface is down, the IP will be
in reset mode (as for some platforms disabling/enabling the clocks will
switch the IP to standby mode, which will lead to losing registers'
content) and applying settings in reset mode is not an option. Instead,
cache the RX CSUM settings and apply them in ravb_open().

Commit prepares for the addition of runtime PM.

Signed-off-by: Claudiu Beznea <[email protected]>
---

Changes in v2:
- none; this patch is new

drivers/net/ethernet/renesas/ravb_main.c | 12 ++++++++++++
1 file changed, 12 insertions(+)

diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
index 633346b6cd7c..9ff943dff522 100644
--- a/drivers/net/ethernet/renesas/ravb_main.c
+++ b/drivers/net/ethernet/renesas/ravb_main.c
@@ -1868,6 +1868,15 @@ static int ravb_open(struct net_device *ndev)
if (info->gptp || info->ccc_gac)
ravb_ptp_init(ndev, priv->pdev);

+ /* Apply features that might have been changed while the interface
+ * was down.
+ */
+ if (ndev->hw_features & NETIF_F_RXCSUM) {
+ u32 val = (ndev->features & NETIF_F_RXCSUM) ? ECMR_RCSC : 0;
+
+ ravb_modify(ndev, ECMR, ECMR_RCSC, val);
+ }
+
/* PHY control start */
error = ravb_phy_start(ndev);
if (error)
@@ -2337,6 +2346,9 @@ static void ravb_set_rx_csum(struct net_device *ndev, bool enable)
struct ravb_private *priv = netdev_priv(ndev);
unsigned long flags;

+ if (!netif_running(ndev))
+ return;
+
spin_lock_irqsave(&priv->lock, flags);

/* Disable TX and RX */
--
2.39.2


2023-12-16 20:36:58

by Sergey Shtylyov

[permalink] [raw]
Subject: Re: [PATCH net-next v2 20/21] net: ravb: Do not apply RX CSUM settings to hardware if the interface is down

On 12/14/23 2:45 PM, Claudiu wrote:

> From: Claudiu Beznea <[email protected]>
>
> Do not apply the RX CSUM settings to hardware if the interface is down. In
> case runtime PM is enabled, and while the interface is down, the IP will be
> in reset mode (as for some platforms disabling/enabling the clocks will
> switch the IP to standby mode, which will lead to losing registers'

To/From perhaps?
And just "register".

> content) and applying settings in reset mode is not an option. Instead,
> cache the RX CSUM settings and apply them in ravb_open().

Have this issue actually occurred for you?

> Commit prepares for the addition of runtime PM.
>
> Signed-off-by: Claudiu Beznea <[email protected]>
[...]

> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
> index 633346b6cd7c..9ff943dff522 100644
> --- a/drivers/net/ethernet/renesas/ravb_main.c
> +++ b/drivers/net/ethernet/renesas/ravb_main.c
> @@ -1868,6 +1868,15 @@ static int ravb_open(struct net_device *ndev)
> if (info->gptp || info->ccc_gac)
> ravb_ptp_init(ndev, priv->pdev);
>
> + /* Apply features that might have been changed while the interface
> + * was down.
> + */
> + if (ndev->hw_features & NETIF_F_RXCSUM) {

I'm afraid this is a wrong field; we need ndev->features, no?

> + u32 val = (ndev->features & NETIF_F_RXCSUM) ? ECMR_RCSC : 0;
> +
> + ravb_modify(ndev, ECMR, ECMR_RCSC, val);
> + }
> +

The ECMR setting is already done in ravb_emac_init_rcar(), no need
to duplicate it here, I think...

> /* PHY control start */
> error = ravb_phy_start(ndev);
> if (error)
> @@ -2337,6 +2346,9 @@ static void ravb_set_rx_csum(struct net_device *ndev, bool enable)
> struct ravb_private *priv = netdev_priv(ndev);
> unsigned long flags;
>
> + if (!netif_running(ndev))

Racy as well...

> + return;
> +

Hm, sh_eth.c doesn't have such check -- perhaps should be fixed
as well...

[...]

MBR, Sergey

2023-12-18 12:24:57

by claudiu beznea

[permalink] [raw]
Subject: Re: [PATCH net-next v2 20/21] net: ravb: Do not apply RX CSUM settings to hardware if the interface is down



On 16.12.2023 22:36, Sergey Shtylyov wrote:
> On 12/14/23 2:45 PM, Claudiu wrote:
>
>> From: Claudiu Beznea <[email protected]>
>>
>> Do not apply the RX CSUM settings to hardware if the interface is down. In
>> case runtime PM is enabled, and while the interface is down, the IP will be
>> in reset mode (as for some platforms disabling/enabling the clocks will
>> switch the IP to standby mode, which will lead to losing registers'
>
> To/From perhaps?
> And just "register".
>
>> content) and applying settings in reset mode is not an option. Instead,
>> cache the RX CSUM settings and apply them in ravb_open().
>
> Have this issue actually occurred for you?

Setting RX CSUM while the if is down? No.

>
>> Commit prepares for the addition of runtime PM.
>>
>> Signed-off-by: Claudiu Beznea <[email protected]>
> [...]
>
>> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
>> index 633346b6cd7c..9ff943dff522 100644
>> --- a/drivers/net/ethernet/renesas/ravb_main.c
>> +++ b/drivers/net/ethernet/renesas/ravb_main.c
>> @@ -1868,6 +1868,15 @@ static int ravb_open(struct net_device *ndev)
>> if (info->gptp || info->ccc_gac)
>> ravb_ptp_init(ndev, priv->pdev);
>>
>> + /* Apply features that might have been changed while the interface
>> + * was down.
>> + */
>> + if (ndev->hw_features & NETIF_F_RXCSUM) {
>
> I'm afraid this is a wrong field; we need ndev->features, no?

RX CSUM is not enabled for all ravb aware devices (see struct
ravb_hw_info::net_hw_features). We should be setting the ECMR only for
these ones. ravb_hw_info::net_hw_features is set in ndev->hw_features in
probe(). So here code checks if platforms supports RXCSUM and then below it
applies what has been requested though ndo_set_features(), if any.

>
>> + u32 val = (ndev->features & NETIF_F_RXCSUM) ? ECMR_RCSC : 0;
>> +
>> + ravb_modify(ndev, ECMR, ECMR_RCSC, val);
>> + }
>> +
>
> The ECMR setting is already done in ravb_emac_init_rcar(), no need
> to duplicate it here, I think...

Ok, it worth being moved there.

>
>> /* PHY control start */
>> error = ravb_phy_start(ndev);
>> if (error)
>> @@ -2337,6 +2346,9 @@ static void ravb_set_rx_csum(struct net_device *ndev, bool enable)
>> struct ravb_private *priv = netdev_priv(ndev);
>> unsigned long flags;
>>
>> + if (!netif_running(ndev))
>
> Racy as well...

It's also called with rtnl_mutex locked.

>
>> + return;
>> +
>
> Hm, sh_eth.c doesn't have such check -- perhaps should be fixed
> as well...
>
> [...]
>
> MBR, Sergey

2023-12-21 18:50:34

by Sergey Shtylyov

[permalink] [raw]
Subject: Re: [PATCH net-next v2 20/21] net: ravb: Do not apply RX CSUM settings to hardware if the interface is down

On 12/17/23 5:34 PM, claudiu beznea wrote:

[...]

>>> From: Claudiu Beznea <[email protected]>
>>>
>>> Do not apply the RX CSUM settings to hardware if the interface is down. In
>>> case runtime PM is enabled, and while the interface is down, the IP will be
>>> in reset mode (as for some platforms disabling/enabling the clocks will
>>> switch the IP to standby mode, which will lead to losing registers'
>>
>> To/From perhaps?
>> And just "register".
>>
>>> content) and applying settings in reset mode is not an option. Instead,
>>> cache the RX CSUM settings and apply them in ravb_open().
>>
>> Have this issue actually occurred for you?
>
> Setting RX CSUM while the if is down? No.
>
>>> Commit prepares for the addition of runtime PM.
>>>
>>> Signed-off-by: Claudiu Beznea <[email protected]>
>> [...]
>>
>>> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
>>> index 633346b6cd7c..9ff943dff522 100644
>>> --- a/drivers/net/ethernet/renesas/ravb_main.c
>>> +++ b/drivers/net/ethernet/renesas/ravb_main.c
>>> @@ -1868,6 +1868,15 @@ static int ravb_open(struct net_device *ndev)
>>> if (info->gptp || info->ccc_gac)
>>> ravb_ptp_init(ndev, priv->pdev);
>>>
>>> + /* Apply features that might have been changed while the interface
>>> + * was down.
>>> + */
>>> + if (ndev->hw_features & NETIF_F_RXCSUM) {
>>
>> I'm afraid this is a wrong field; we need ndev->features, no?
>
> RX CSUM is not enabled for all ravb aware devices (see struct
> ravb_hw_info::net_hw_features). We should be setting the ECMR only for
> these ones. ravb_hw_info::net_hw_features is set in ndev->hw_features in
> probe(). So here code checks if platforms supports RXCSUM and then below it
> applies what has been requested though ndo_set_features(), if any.

OK. But we don't need this snippet here anyway...

>>> + u32 val = (ndev->features & NETIF_F_RXCSUM) ? ECMR_RCSC : 0;
>>> +
>>> + ravb_modify(ndev, ECMR, ECMR_RCSC, val);
>>> + }
>>> +
>>
>> The ECMR setting is already done in ravb_emac_init_rcar(), no need
>> to duplicate it here, I think...
>
> Ok, it worth being moved there.

No need to move, it's already there...

[...]
>>> @@ -2337,6 +2346,9 @@ static void ravb_set_rx_csum(struct net_device *ndev, bool enable)
>>> struct ravb_private *priv = netdev_priv(ndev);
>>> unsigned long flags;
>>>
>>> + if (!netif_running(ndev))
>>
>> Racy as well...
>
> It's also called with rtnl_mutex locked.

Well, at least the only place that calls the ndo_set_features()
method, __netdev_update_features() calls ASSERT_RTNL() at the start.
However, since we'd have to use the is_opened flag anyway, let's rely
on it instead...

[...]

MBR, Sergey